subcategories
(3rd category level)
Manufacturer:
(Category: 107)
tube diameter: 48,3 mmwall strength: 3,25 mmbending radius min.: max. 180 mmBending speed: 20 °/sectotal power requirement: 2,4 kWweight of the machine ca.: 700 tdimensions of the machine ca.: 3880 x 800 x 1250 mDescription:Round tube steel (S235): 60.0 x 6.0 mmRound tube stainless steel (S 355): 60.0 x 4.0 mmSquare tube steel: 50 x 50 x 4.0 mmRectangular tube steel: 60 x 40 x 2.0 mmmax. usable length: 3048 mmBending speed: 10°/secincluding tools (see photos)Mandrel is no longer available, can be retrofittedThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Key data: 3100 mm, 16 mm
- Year of construction 2001 Specifications - Cutting length: 3100 mm - Capacity: 16 mm - Stroke: 170 mm - Stroke rate: 10 /min - Oil tank: 410 l - Engine power: 37 kW - Operating voltage: 400 V - Rated current: 72 A - Rated current main fuse: 100 A - Dimensions WxHxD: 3750 x 2400 x 3425 mm - Weight: 13800 kg
Key data: 1100 mm, 1 t
Paternoster for sheet metal coils 7 gondolas, each with a usable width of 110 cm Load capacity 1300 kg Net weight 800 kg Height 235 cm
Little-used guillotine shears, only occasionally 1.5 mm sheet thickness Stroke rate 56/ min. Power (Rm 400/mm) 3.5mm Rated power 4.0 kVA Weight 860 kg
OFFER PLATE ROLL 2000x6 mm SERGI 3ROLL INITIAL PINCH ASYMMETRIC 2050 X6 MM Rolls length 2050 mm -Top roll 170 mm -lower/Side rolls 150 mm -Power electric 5,5 Hp Capacity -plate width 2000 mm -plate thickness 6 mm with prepinch Configuration on the machine -Rollers surface hardened high strength -Central rolls driven electric rotation on gearunit -side roll electric run with prepinch Pinch roll position with handwheel Front open manual drop-end -Readout gauge of side bending roll -Foot-pedal electric rollers rotation back/forth -Joystick electric control of side roll -Safety installations with emergency stop. -Machine in good conditions
Profiles bending roll Tauring Alfa 70H2 year 2003 Used machine in perfect working condition Technical data: -Hydraulic section bending machine with digital readout -dual pre-pinch pyramid roll configuration 3 rolls powered driven - Shafts output 70 mm – Size of universal rollers 245 mm Lateral correctors left/right side hydraulic motorized operated Machine reversible can work with shafts vertical/horizontal Tooling: -Set of universal rolls and spacers Pipe bending rolls set for tube size 22,5 – 61 – 76 - ( see photos of the rolls in enclosed ) Power total installed 5,5Kw Vac 380/50 Dimension 1640 x 1220 x H1580 mm Weight 1300 kgs -CAPACITY CHART IN ENCLOSED ::::::
Key data: 200 mm, 300 , 200
Profile bending roll used equipment hydraulic model AR200 year 2008 make MG Italy Capacity bending chart photo in enclosed -Technical data: Output shafts size 200 mm -Machine complete with set of rollers adjustable for the various shape of profiles. -Traction tool hydraulic operated for the HEB-beam - IPE - UNP bending the hard side. -Lateral correctors left and right side hydraulic operated in 3 direction. -Included additional set of rolls for pipe 6" inches -Machine with 3 rolls driven system with individual hydraulic motor and axial gear-unit on each shaft. -The 3 shafts working on bearings, heavy duty type with sealed lubrication. -Centralized control panel movable on wheels with all electric commands. -Dual rolling speed up to 5 mtr/min with automatic balancing system between the 3 rolls. -Safety devices in compliance with European regulation ...
Key data: 200 mm, 400 , 360
Profile Bending machine Model AR360 -Year 2004 MG brand made in Italy OUTPUT SHAFTS 360 MM Capacity as per the original bending chart here enclosed Configuration installed with the machine -Pyramid dual pinch side rolls independent hydraulic positioning bending and pre-bending performance -The 3 shafts driven with hydraulic motor and gear unit individual on each roll -Synchronized speed automatic hydraulic control between the 3 rotating shafts -hydraulic traction tool to roll HEB_INP_UPN bending on hard-side. -Lateral correctors left/right hydraulic operated in 3 directions Tooling with the machine -Set of rollers for pipe: 6” and 12” -Set of rollers with adjustable opening width up to 400 mm ( for all the profiles bending easy way and hard way ) -Set of rings to increase the rollers opening width up to 500 mm ( for all the symmetric pro ...
Capacity plate width up to 3000 mm thickness 22 mm plate prebend 18 mm dual prepinch technical data: -length of rolls 3100 mm -top roll dia. 350mm -lower roll dia. 330mm -Hydraulic power unit with 20Hp motor -Electric supply Vac 400/50 – 480/60 Configuration complete: -Hardened surface of the 4 rolls -Conical plate bend hydraulic attachment. -hydraulic power driven rolls rotation with gear unit axial each -Synchronized hydraulic power dragging . -front open drop-end to remove closed shells. -Calibration re-rolling feature for welded shells Safety configuration in compliance. Control console electric commands with digital readout Predisposed ready to connect nr. 1 central hydraulic support for large dia. nr. 1 side arm hydraulic to hold in place think plate sheet being formed
pressure: 135 tchamfer lenght: 4100 mmdistance between columns: 3600 mmcolumn arm: 410 mmram stroke speed: 200 mm/secwork speed: 12.0 mm/secreturn speed: 190 mm/secwork stroke: 275 mmdayligth: 550 mmtable height: 900 mmoil volume: 300 ltr.voltage: 400 Volttotal power requirement: 15.0 kWweight: 10800 kgrange L-W-H: 5100 x 2100 x 2850 mm-------------------------------------------------- HIGH-SPEED hydraulic press brake withincreased installation heightincreased cylinder strokeenlarged projection-------------------------------------------------- Furnishing:- DELEM CNC control model DA 66T- swiveling touchscreen control unit- 7 controlled axes: Y1 - Y2 - X - R - Z1 and Z2, as well as CNC crowning- electr. controlled backgauge X-axis = 800 mm / R-axis = 250 mm- on ball screws- controlled electr. Stop fingers Z1 + Z2- split upper deer foot tool Roleri 135.85.R08, System A- with additional cro ...
pressure: 220 tchamfer lenght: 4100 mmdistance between columns: 3600 mmcolumn arm: 410 mmram stroke speed: 180 mm/secwork speed: 10.0 mm/secreturn speed: 185 mm/secwork stroke: 275 mmdayligth: 550 mmtable height: 900 mmtable width: 160 mmback stop - adjustable: max. 800 mmoil volume: 300 ltr.voltage: 400 Volttotal power requirement: 18.5 kWweight: 14000 kgrange L-W-H: 5150 x 2250 x 3000 mm-------------------------------------------------- HIGH-SPEED hydraulic press brake withincreased installation heightincreased cylinder strokeenlarged projection-------------------------------------------------- Furnishing:- DELEM CNC control model DA 66T- swiveling touchscreen control unit- 7 controlled axes: Y1 - Y2 - X - R - Z1 and Z2, as well as CNC crowning- electr. controlled backgauge X-axis = 800 mm / R-axis = 250 mm- on ball screws- controlled electr. Stop fingers Z1 + Z2- split upper deer foot ...
diameter of brush: Ø 250 mmwidth of brush: 40.0 mmturning speed range: 2850 U/minvoltage: 400 Volttotal power requirement: 1.3 / 1.8 kWweight of the machine ca.: 36.0 kgdimensions of the machine ca.: 415 x 467 x 356 mmEquipment:- Deburring of individual pieces and small series- Deburring of stretched round, rectangular and square tubes + flat material- Heavy, durable industrial design- with maintenance-free motor- long service life and very smooth running thanks to balanced rotor- with quality ball bearings- storage area for safety glasses- incl. 1x multi-purpose wire brush, wire thickness 0.35 mm- operating instructionsThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
pressure: 225 tchamfer lenght: 3050 mmdistance between columns: 2550 mmcolumn arm: 300 mmajustment speed: 110 mm/secwork speed: 9.0 mm/secreturn speed: 130 mm/secwork stroke: 240 mmdayligth: 320 - 560 mmtable height: 1000 mmtable width: 200 mmoil volume: 350 ltr.operating pressure: max. 296 barair pressure: 4.5 - 6.0 barvoltage: 400 Volttotal power requirement: 18.5 kWweight: 14900 kgrange L-W-H: 5180 x 2400 x 3100 mm- in checked condition - machine video -https://www.youtube.com/watch?v=ebbbzSYMxKwFurnishing:- electro-hydraulic CNC die bending/press brake- CYBELEC CNC control ModEva 12S, swiveling at the front right High-resolution graphic color screen 14 inches Representation as a line, area or volume drawing of the product Clear, concise menus in the operators language Large tools and products library- CNC-controlled back gauge adjustment (X-axis) Stop range X axis of bending line .. ...
pressure: 320 tchamfer lenght: 3100 mmdistance between columns: 2600 mmcolumn arm: 410 mmram stroke speed: 140 mm/secwork speed: 10.5 mm/secreturn speed: 150 mm/secwork stroke: 375 mmdayligth: 650 mmtable height: 900 mmtable width: 240 mmoil volume: 400 ltr.voltage: 400 Volttotal power requirement: 30.0 kWweight: 17082 kgDimensions (HxWxD): 4550 x 2450 x 3200 mm-------------------------------------------------- HIGH-SPEED hydraulic press brake withincreased installation heightincreased cylinder strokeenlarged projection-------------------------------------------------- Furnishing:- DELEM CNC control model DA 66T- swiveling touchscreen control unit- 7 controlled axes: Y1 - Y2 - X - R - Z1 and Z2, as well as CNC crowning- electr. controlled backgauge X-axis = 800 mm / R-axis = 250 mm- on ball screws- controlled electr. Stop fingers Z1 + Z2- split upper deer foot tool Roleri 135.85.R08, Sys ...
pressure: 160 tchamfer lenght: 3760 mmdistance between columns: 3250 mmcolumn arm: 250 mmram stroke speed: 90.0 mm/secwork speed: 7.5 mm/minreturn speed: 80.0 mm/secwork stroke: 160 mmdayligth: 395 mmtable height: 900 mmoil volume: 200 ltr.voltage: 400 Voltweight: 8514 kgrange L-W-H: 4910 x 1900 x 2550 mmFurnishing:- DELEM - CNC control model DA-58T- controlled axes: Y1 - Y2 and X- SICK light barrier in front of the machine- Upper tool, deer foot- Lower tool, die block with 4Vs- manual table crowning- SICK light barrier behind the machine- 2 front support arms- SIEMENS - electrical system- BOSCH / HOERBIGER hydraulic system- CE mark / declaration of conformity- Operating manual: machine and control- Safety manual: press brakes The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
pressure: 85.0 tchamfer lenght: 2050 mmdistance between columns: 1750 mmcolumn arm: 410 mmstroke: 365 mmdayligth: 535 mmajustment speed: 200 mm/secworking feed: 1.0 - 10.0 mm/secreturn speed: 135 mm/secback stop - adjustable: max. 600 mmtable width: 120 mmwork height max.: 1050 mmNumber of working hours: 28.500 hoil volume: 200 loperating pressure: 340 bartotal power requirement: 14.0 kVAweight of the machine ca.: 9050 kgrange L-W-H: 2680 x 2100 x 2885 mm with increased installation height / piston stroke very well maintained condition () with only approx. 28.500 operating hours- in checked condition - machine video -https://www.youtube.com/watch?v=ZuwyPKJSYLwEquipment:- CNC electro-hydraulic press brake- including DELEM CNC control swiveling control panel at the front left- CNC controlled axes: Y1 - Y2 - X - R - Z1 - Z2 - I + CNC crowning- CNC electro-motorized back stop (X axis)- CNC e ...
pressure: 175 tchamfer lenght: 3100 mmdistance between columns: 2600 mmcolumn arm: 410 mmram stroke speed: 180 mm/secwork speed: 10.0 mm/secreturn speed: 135 mm/secwork stroke: 275 mmdayligth: 550 mmtable height: 900 mmtable width: 90.0 mmoil volume: 200 ltr.voltage: 400 Volttotal power requirement: 15.0 kWweight: 9450 kgrange L-W-H: 4250 x 2150 x 2800 mm--------------------------------------------------Press brake with special equipment increased installation height increased cylinder stroke as well as increased bending beam speeds-------------------------------------------------- Furnishing:- DELEM CNC control model DA-58T graphic/touch screen 2D graphical programming 15 TFT color screen with high resolution Bending sequence calculation Product programming and real size display USB interface- Motorized backgauge with R-axis, on ball screws- X = 800 mm R = 250 mm with 2 stop fingers- co ...
pressure: 60,0 tsquare edge steel: 35,0 mmround bar steel: 40,0 mmL-beam: 120x120x12 mmpunching cross-cut in cmm: Ø28 in 15 / Ø38 in 11 mmthroat: 220 mmflat steel: 200x20 / 300x15 mmblade length: 317 mmoil volume: 45,0 ltr.work height max.: 940 / 1140 mmstrokes per minute: max. 26 work stroke: 55,0 mmtotal power requirement: 4,0 kWweight of the machine ca.: 1425 kg.Dimensions (HxWxD): 1510 x 590 x 1570 mmFurnishing:- Support table at the hole punch- Support table on the square notcher- foot switch- Bed. Instructions- CE declaration+ MUBEA - punch and die holderThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
sheet width: 1600 mmplate thickness: 15,0 mm STpre-bending: 13,0 mm STdiameter of upper rolls: 230 mmside roll diameter: 210 mmdiameter of lower rolls: 190 mmtotal power requirement: 7,5 kWweight of the machine ca.: 4225 kg.dimensions of the machine ca.: 4000 x 1300 x 1440 mmFurnishing:- electro-hydraulic 4-roller bending machine- 2x driven main rollers (upper & lower roller)- with hydraulic conical bending device- Induction hardened rollers- including straightening function for welded pipes- Control unit / display with touch screen function digital position display for the two side rollers- mobile control panel- 2x bending speeds selectable- hydraulic folding bearing- Safety device (safety line with switch unit)- Pressure gauge / pressure indicator for the rollers- CE mark + declaration of conformity- Operation manualThe data for this ad was created with ModulMWS - the software solution ...
weight max.: 5000 kgtable turning speeds: 6 - 60 m/hroll diameter: 250 x 120 mmworkpiece diameter: 250 - 2.800 mmweight: 300 kgrange L-W-H: 0 mm Antriebrange L-W-H: 0 mm Mitläufertotal power requirement: 0,75 kWStable turningThe HGK_Series has two synchronously working drive units that are used forensure continuous rotation with stepless speed control. Of the Roller spacing can be increased and decreased manually using locking pins to achieve a large diameter range of the workpieces.Characteristics:- For rotating and positioning- in the field of machine, container, plant and pipeline construction- Two synchronously running drive motors- Adjustable rotation speed.- PU castors- Adjustment is via bolts- Remote controlScope of delivery:- 1x controller- 1x driven unit- 1x traveling unitThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
sheet width: 3100 mmplate thickness: 6,0 mmthickness at Niro-steel: 4,0 mmdown holder: 14 Stückno. of strokes: 20 Hub/mincutting angle: 1,2 °control: CYBELEC CybTouchwork height max.: 800 mmoil volume: 150 ltr.total power requirement: 11,0 kWweight: 5500 kgrange L-W-H: 4.000 x 2.410 x 1.640 mm-------------------------------------------------electr. / hydraulic CNC swing cut shears with CYBELEC CNC touch screen control with electr. / hydr. Kerf adjustment-------------------------------------------------Furnishing: - CNC electr. / hydraulic swing cut shears- CYBELEC CNC touch screen controller, model CybTouch 8 Backgauge preselection - X axis Cutting gap adjustment Quantity Cutting length limitation Material preselection, including sheet thickness Cutting line lighting- motorized backgauge, travel = 1,000 mm (X axis) on ball screws autom. Can be folded up at max.travel, for longer cuts- ...
sheet width: 4080 mmplate thickness: 2.0 mm STthickness at Niro-steel: 0.8 mmSheet thickness for ALU: 2.5 mmno. of strokes: 34 Hub/mincutting angle: 1.3 Graddistance between columns: 4310 mmback stop - adjustable: 15.0 - 750 mmtable height: 820 mmControl: ELGO engine output: 9.0 kWweight of the machine ca.: 3600 kg.range L-W-H: 5250 x 2200 x 1400 mm Good condition () Current new price approx. €70,000 Special price upon requestThe MHSU motor-driven guillotine shear is based on a torsion-free, rigid welded construction and a dynamic, quiet, and powerful gear motor. High static and dynamic rigidity is ensured by robustly dimensioned main components such as the cutter bar, support table, side supports,and the main drive unit. The motor-driven guillotine shear was developed forsheet metal and plastics processing. With these shears, you can effortlessly produce clean cuts in series.Features: ...
tube diameter: 1/2 - 2.0 Zollwall strength: 2.75 - 4.5 mm STpressure: 10.0 tweight of the machine ca.: 46.0 kgWith a hinged bending frame for efficient work- Various bending dies included- Universally applicable for gas, boiler, and water pipes- Fast work thanks to rapid feed- With a tripod stand for safe work- Also ideal for copper and coated pipes- Bends up to 90° can be createdFeatures:- Bending dies: ½ - ¾ - 1 - 1 ¼ - 1 ½ - 2The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
sheet width: 3100 mmplate thickness: 6,0 mmdistance between columns: 3.100 mmdown holder: 14 Stückno. of strokes: 16 - 24 Hub/minoil volume: 150 ltr.cutting angle: 0,5 - 1,5 °thickness at Niro-steel: 4,0 mmcolumn arm: 350 mmengine output: 11,0 kWweight of the machine ca.: 7.060 kgrange L-W-H: 4100 x 2200 x 2190 mm--------------------------------------------------electr. / hydraulic CNC guillotine shears - guided by a backdrop with CYBELEC CNC touch screen control with electr. / hydr. Cutting gap and cutting angle adjustment-------------------------------------------------- Furnishing:- CNC guiding guillotine shears- with electr. / hydr. Cutting gap and cutting angle adjustment- CYBELEC CNC touch screen controller, model CybTouch 8 Backgauge preselection - X axis Cutting gap adjustment Number of pieces Cutting length limitation Material preselection, including sheet thickness Cutting li ...
tube diameter: 42,0 mm Stahlwall strength: 3,0 mm Stahltube diameter: 54,0 mm CU/Aluwall strength: 2,0 mmbar material - diameter: 30,0 mmrevolutions per minute: 2,0 U/minvoltage: 400 Volttotal power requirement: 1,1 kWweight: 80,0 kgrange L-W-H: 410 x 1000 x 570 mm Demonstration/demo machine () from our exhibition (like NEW) with very few operating hours current new price approx. 8.000 euros special price on requestERCOLINA MediBender MB 42 M- Capacity steel pipe 42 x 3.0mm- Capacity gas pipe 11/4 gas x 3.5 mm- Capacity square profile (FE 42) 35 x 35 x 3 mm- Max. bending radius 10-260 mm- Minimum radius 2 x D- 6-edge tool holder- Min. outside diameter 5 mm - 1/8 gasEquipment:- patented fast tool change system- one bending speed- freely movable foot switch- bending tools on request for an additional chargeincluding ERCOLINA microprocessor control:- with 30 programs (0 - 29)- each program ...
sheet width: 3100 mmplate thickness: 13,0 mmthickness at Niro-steel: 8,0 mmdown holder: 14 Stückno. of strokes: 11 - 20 Hub/minoil volume: 310 ltr.cutting angle: 0,05 - 2,0 °throat: 350 mmtable height: 900 mmtotal power requirement: 22,0 kWweight of the machine ca.: 13.300 kgrange L-W-H: 5.110 x 2.570 x 2.400 mm-------------------------------------------------- heavy electr. / hydraulic CNC guillotine shears - guided by a backdrop with CYBELEC CNC touch screen control with electr. / hydr. Cutting gap and cutting angle adjustment-------------------------------------------------- Furnishing:- CNC guillotine guiding shears- with electr. / hydr. Cutting gap and cutting angle adjustment- CYBELEC CNC touch screen controller, model CybTouch 8 Backgauge preselection - X axis Cutting gap adjustment Number of pieces Cutting length limitation Material preselection, including sheet thickness Cutt ...
sheet width: 2065 mmplate thickness: 1,20 mmdaylight opening: mit WZ 35,0 mmdaylight opening: ohne WZ 60,0 mmbending angle max.: 0 - 135 °total power requirement: manuell weight of the machine ca.: 520 kg.dimensions of the machine ca.: 2400 x 1115 x 1150 mm- Segmented upper beam for a large number of bending options- Universally applicable bending machine for plumbing and repair shops- High upper beam for the production of high-edged profiles- Quick and easy bending process using a bow handle- Easy adjustment of the upper beam for efficient work- The bending angle is set using a scale- Individually removable segments for bending boxes- Robust construction in a modern designFurnishing :- segmented upper beam + bending beam- Foot clamp- Fixed stop for angle adjustment- back gauge- bending segments 38 | 38 | 38 | 50 | 50 | 50 | 50 | 76 | 76 | 101 | 127 | 152 | 203 | 254 | 254 | 254 | 254 ...
cutting capacity: 2.0 mmthroat: 700 / 280 mmround blank diameter max.: 1000 mmround blank diameter min.: 120 mmspeed: 7.0 m/mintotal power requirement: 1.10 kWweight of the machine ca.: 360 kgrange L-W-H: 1400 x 400 x 1150 mm Exhibition machine - like NEW not yet in use () Special price on requestEquipment:- electro-motor-driven circular shears with large projection- with hardened blades- machine base- manual setting of the desired round diameter- manual material clamping- electric motor brake- 1x freely movable foot switch including emergency stop buttonThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
sheet width: 2020 mmplate thickness: 2,0 mmdaylight opening: 124 mmbending angle max.: 0 - 135 °work height max.: 930 mmtotal power requirement: von Hand kWweight of the machine ca.: 1.010 kgdimensions of the machine ca.: 2,75 x 0,56 x 1,26 mcharacteristics- Easy to use swivel bending machine- Flat guide for exact movement of the upper beam- Manually adjustable bending angle using a scale- Robust welded steel construction, designed for heavy use- Large opening width for processing tall workpieces- Optionally with back gauge for series work- Quick and easy bending process using a bow handle- Workpiece clamping by means of a large leverThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
sheet width: 2020 mmplate thickness: 2,0 mmdaylight opening: 122 mit Segmente mmbending angle max.: 0 - 135 °work height max.: 930 mmtotal power requirement: von Hand kWweight of the machine ca.: 1020 kgdimensions of the machine ca.: 2,75 x 0,56 x 1,26 mcharacteristics- Segmented upper beam for a large number of bending options- Universally applicable bending machine for plumbing and repair shops- High upper beam for producing high-edged profiles- Quick and easy bending process using a bow handle- Easy adjustment of the upper beam for efficient work- The bending angle is set using a scale- Individually removable segments for bending boxes- Large opening width for processing large workpieces- Robust construction in a modern designscope of delivery- Segmented upper cheek- Biegesegm. 25 | 30 | 35 | 40 | 50 | 75 | 100 | 150 | 200 | 300 | 500 | 510 mmThe data for this ad was created with Mod ...
