plastics and rubber processing machines used for sale (3,068)

used VMI - Holland HP- Batch off (Tunnel) Refrigeration system. available Tunnel Batch off from VMI Description attached!

used Battenfeld + Theysohn Plastic injection machines. 2 pieces Note: - No forklift etc. on site - Oils must be taken with you

used Theysohn und Battenfeld Theysohn + Battenfeld. Extruders Theysohn and Battenfeld

used HF IM90E Mixer Body. HF IM90E Mixer Body and Hydraulic Hopper

used Francis Shaw K4 Mixer Body. K4 Mixer Body and Hydraulic Hopper

used HOLLINGER KPSM-E-V III. Year: 2006 - technically efficient, ready to work – after full service - flash limit: 2 mm - angle range: 30-180 degrees - large heater - side supports - air preparation station

Key data: 1400 kN, 139 g/PS, 35 mm

used ENGEL Victory330/140 tech. 1.0 St. gebr. Injection Molding Machine with Robot, Machine comes from cleanroom production Manufacturer: ENGEL Type: VICTORY 330/140 TECH Year of Make: 2011 Clamping force: 140 tons Spar spacing: SPARLESS Screws DN: 35 mm Max. displacement: 154 ccm³ Moulded part weight 139 g/hp Control: CC200 Equipment: -Robot, manufacturer: Engel, type: V12 -2 x Core Pull -Blow-out valve -16 hot runner control zones -Protective fence -Conveyor belt

used ARBURG 420C1300-150-60 LSR. R1336 Arburg 420C1300 150 2 K +extra injection module LSR silicone here is a very well-preserved, very highly equipped injection molding machine at the warehouse in ergenzingen was training machine from the universityOnly 6496 operating hours autom and 8628 pump.Accessories roughly expressed 2 K machine and additionally a SLR silicone injection module with the necessary connections on the machine. With hydraulic swivel table, what else the machine can do, we will only be able to do it after connection /Construction.

used CR Clarke 1820 Vacuum Former. It is in good cosmetic condition and in good working order.

used Wanner C17.26sv. The Compact Series The new Wanner granulators of the C's series ("C" stands for "compact", "s" stands for "silent") offer practical solutions for almost all problems for the in-line recycling of sprues and defective parts in the production process. Due to the modular design, the granulators of the C's series can be easily adapted to the respective application or the needs of the company. Depending on the method of feeding the sprues, the disposal of the regrind, or the type of sprue used, Injection molding machine, the C's series from Wanner offers optimal solutions that can be adapted to your respective operating process through a variety of standard components. The optimised cutting geometry and the low rotor speed guarantee high-quality regrind with a low dust content, sound-insulated insertion shafts and The grinding chamber structure optimised in ter ...

used ARBURG 270 S 250 . 150 Selocica. Training machine only autom 550 operating hours R1344 Injection moulding machine ARBURG Type 270 S - 250 - 150 built in 2001 SELOGICA control system Very well-maintained training machine with few operating hours approx. 550 h car and 1,300 hPump Screws D = 30mm Machine has now (May 2026) been converted to new software and CF Drive Machine can be demonstrated under power and instructed by a specialist

used Nordmeccanica Duplex Compact SL 1300. Technical description  Laminator for foil finishing . Solvent-free lamination . Foil _Folie, Alu foil, Cylinder width 1310 mm Laminating width 1300 mm Laminator Type = Duplex Diameter unwinder = 850 mm ( turnstile ) Diameter rewinder = 850 mm ( turnstile ) Sleeve 3 and 6 inches, Speed max = 450 m/ min. With accessories 

used Husky HN600. Injection molding machine Husky HN600 BJ 2019

used Dreher und Wanner Mills. 1 x Mill Turner 1 x Mill Wanner

used BORCHE Bi 2240/320. B&A REF: 9228 TON: 320 SCREW DIAMETER: 70MM SHOT WEIGHT: 1266 STROKE VOLUME: 1346CM3 INJECTION PRESSURE: 1660AR PLATEN SIZES: 990 X 990MM DBTB: 680 X 680MM MIN MOULD HEIGHT: 260MM MAX MOULD HEIGHT: 680MM MOULD OPENING STROKE: 650MM MAX DAYLIGHT: 1330MM EJECTOR STROKE: 180MM CONTROLS: KEBA CORE PULLING: 2 AIR VALVES: 2 MOTOR: 45 HEATING CAPACITY: 18.5KW ROBOT INTERFACE: EUROMAP 67 SCREW DRIVE: HYDRAULIC

used UNILOY MILACRON UMA 12 SH EZ SECO2 D Suction Blow Molding Machine. Brand: UNILOY MILACRON Model: UMA 12 SH EZ SECO2 3D Suction Blow Molding Machine , Automotive air ducts / conduits production. (video available). Year: 2010 Materials used: PP, PP-EPDM, TPC Machine time under power (h): 22,496 h Screw diameter (mm): 2 screws Ø60 23.6L/D) Head-Accumulation volume: MULLER - 792 cm³ Max. die diameter: 28 mm Locking force (t): 12 t Platform dimensions (H x W): 765 x 800 mm Max. mold dimensions (H x W): 1140 x 1600 mm Max. mold weight: 2500 kg Opening (min/max): 800/1400 mm Oil volume: 100 L Press weight: 19,650 kg Press dimensions (L x W x H): 5.5 x 6.2 x 4 m

used MORETTO SX 205 Dryer. MORETTO DRYER Model : SX 205 Year: 2013 Airflow: 200 m³/h Static Pressure : 200 mbar Blower Power : 3 kW Dew Point : -45°C

used NEGRI BOSSI VE 210-720. B&A REF: 9305 TON: 210 SCREW DIAMETER: 45MM SHOT WEIGHT: 330 STROKE VOLUME: 360CM3 INJECTION PRESSURE: 2000AR PLATEN SIZES: 870 X 790MM DBTB: 570 X 510MM MIN MOULD HEIGHT: 200MM MAX MOULD HEIGHT: 630MM MOULD OPENING STROKE: 540MM MAX DAYLIGHT: 1170MM EJECTOR STROKE: 225MM CONTROLS: DIMI EL2 PLUS CORE PULLING: 2 AIR VALVES: 1 HEATING CAPACITY: 12KW SCREW DRIVE: ELECTRIC

used NEGRI BOSSI V2100H-1600. B&A REF: 9262 TON: 210 SCREW DIAMETER: 60MM SHOT WEIGHT: 800 STROKE VOLUME: 880CM3 INJECTION PRESSURE: 1840AR PLATEN SIZES: 870 X 790MM DBTB: 710 X 510MM MIN MOULD HEIGHT: 200MM MAX MOULD HEIGHT: 630MM MOULD OPENING STROKE: 540MM MAX DAYLIGHT: 1170MM EJECTOR STROKE: 225MM CONTROLS: DIMI EL2 PLUS CORE PULLING: 1 AIR VALVES: 1 MOTOR: 30 HEATING CAPACITY: 25KW SCREW DRIVE: HYDRAULIC

used KRAUSS MAFFEI CX 160-1000. B&A REF: 9322 TON: 160 SCREW DIAMETER: 55MM SHOT WEIGHT: 476 STROKE VOLUME: 523CM3 INJECTION PRESSURE: 1904AR PLATEN SIZES: 820 X 845MM DBTB: 520 X 520MM MIN MOULD HEIGHT: 300MM MOULD OPENING STROKE: 650MM MAX DAYLIGHT: 950MM EJECTOR STROKE: 150MM CONTROLS: MC5 CORE PULLING: 1 AIR VALVES: 1 MOTOR: 30 HEATING CAPACITY: 19.5KW ROBOT INTERFACE: EUROMAP 67 SCREW DRIVE: HYDRAULIC

used DEMAG SYSTEC 160 / 520-840 C. B&A REF: 9291 TON: 160 SCREW DIAMETER: 50MM SHOT WEIGHT: 402 STROKE VOLUME: 442CM3 INJECTION PRESSURE: 1946AR PLATEN SIZES: 770 X770MM DBTB: 520 X 520MM MIN MOULD HEIGHT: 275MM MAX MOULD HEIGHT: 585MM MOULD OPENING STROKE: 500MM MAX DAYLIGHT: 1085MM EJECTOR STROKE: 160MM CONTROLS: NC5 CORE PULLING: 1 AIR VALVES: 1 MOTOR: 22 SERVO DRIVE HEATING CAPACITY: 14.8KW ROBOT INTERFACE: EUROMAP 67 SCREW DRIVE: HYDRAULIC

used KRAUSS MAFFEI CX 110-380. B&A REF: 9128 TON: 110 SCREW DIAMETER: 40MM SHOT WEIGHT: 183 STROKE VOLUME: 201CM3 INJECTION PRESSURE: 1860AR PLATEN SIZES: 745 X 770MM DBTB: 470 X 470MM MIN MOULD HEIGHT: 300MM MOULD OPENING STROKE: 600MM MAX DAYLIGHT: 900MM EJECTOR STROKE: 150MM CONTROLS: MC5 CORE PULLING: 1 AIR VALVES: 1 MOTOR: 22 HEATING CAPACITY: 10.97KW ROBOT INTERFACE: EUROMAP 67 SCREW DRIVE: HYDRAULIC

used BATTENFELD CDC BA 1000 / 315. B&A REF: 9323 TON: 100 SCREW DIAMETER: 35MM SHOT WEIGHT: 140 STROKE VOLUME: 153CM3 INJECTION PRESSURE: 2057AR PLATEN SIZES: 620 X 620MM DBTB: 420 X 420MM MIN MOULD HEIGHT: 250MM MOULD OPENING STROKE: 475MM MAX DAYLIGHT: 725MM EJECTOR STROKE: 150MM CONTROLS: UNILOG TC 40 CORE PULLING: 1 AIR VALVES: 1 MOTOR: 20 HEATING CAPACITY: 8.9KW SCREW DRIVE: HYDRAULIC

used ROMI EN 370. B&A REF: 9309 TON: 70 SCREW DIAMETER: 40MM SHOT WEIGHT: 215 STROKE VOLUME: 226CM3 INJECTION PRESSURE: 1500AR PLATEN SIZES: 540 X 540MM DBTB: 360 X 360MM MIN MOULD HEIGHT: 130MM MAX MOULD HEIGHT: 360MM MOULD OPENING STROKE: 360MM MAX DAYLIGHT: 720MM EJECTOR STROKE: 100MM CONTROLS: CM 10 CORE PULLING: 1 AIR VALVES: 1 MOTOR: SERVO 11 HEATING CAPACITY: 10KW ROBOT INTERFACE: EUROMAP 67 SCREW DRIVE: HYDRAULIC

used BATTENFELD MICROSYSTEM MM 50/50. B&A REF: 9170 TON: 50 SCREW DIAMETER: 14MM SHOT WEIGHT: 1 STROKE VOLUME: 1.1CM3 INJECTION PRESSURE: 2500AR PLATEN SIZES: 364 X 196MM MIN MOULD HEIGHT: 100MM MOULD OPENING STROKE: 200MM MAX DAYLIGHT: 300MM EJECTOR STROKE: 50MM CONTROLS: UNILOG B4

used URBAN AKS 3950. URBAN AKS 3950 2 head welder - very good condition - barely used, perfect condition

Key data: 2000 kN

used Battenfeld VERTICAL. Battenfeld VERTICAL V - 200T Clamping Force: 200T Machine Brand: Battenfeld Type: Single Material Unit: V 1000 Rotating System: Yes Number of Stations: 4 Distance Between Columns: 575 mm Table Diameter: 1520 mm Table Height: 700 mm Mold Thickness (Min/Max): 300 x 600 mm Opening Stroke: 300 mm Molding Screw Diameter: 50 mm Molding Injection Volume: 491 L/1000 km Number of Pneumatic Cores: 1 Number of Hydraulic Cores: 4 Rotating Tables: Yes Harting Injection Ports (Spins): 24 Harting Ejection Ports (Spins): 16 Molding Washer Diameter: 160 mm

Key data: 1500 kN, 35 mm

used ARBURG 470 C Golden Edition. Arburg 470 C Golden Edition – 150T Year of manufacture 2006 Screw diameter: 35 mm Pump hours: 33,756 h Automatic operating hours: 26,507 h Connection: 400V 50 Hz Installed power: 33 kW The press is operational and in good working order.

Key data: 8000 kN, 105 mm

used ENGEL ES5550/800. Engel ES5550/800 – 800T Manufacturing date: 2001 Closing Technology : toggle Ejection plate : yes Cores : 4 Cooling circuits : 12+12 Magnetic plates: No (will be removed before selling). Equipped with E70.0 Screw diameter: 105mm Barrel volume: 3720cm3 Specific pressure: 1400bars No hot runner No mold heating (separated heating system) PLC: CC100 Operating hours: 102 694h + Robot SEPRO 3061 – S900-II (2002)

Key data: 6500 kN, 90 mm

used ENGEL ES4550/650. Engel ES4550/650 - 650T Year : 1998 Closing Technology : toggle Ejection plate : yes Cores : 4 Cooling circuits : 11+11 Magnetic plates: No Screw diameter: 90mm Barrel volume: 2480cm3 Specific pressure: 2180bars No hot runner No mold heating (separated heating system) PLC: CC100 Operating hours: 126 046h + Robot SEPRO 3041 – S900-II (1997)

used Arburg 470C, 270M, 270S, 320M. 4 x Arburg injection moulding machines Injection moulding machine Arburg 470C 1500-400 BJ 2008 Injection moulding machine Arburg 270M built in 1995 Injection moulding machine Arburg 270S 500-150 BJ 2004 Sprise casting machine Arburg 320M 750-210 BJ 1998

used Dae Kong DKF 3600 EPS Pre-Expander. For sale is an EPS pressure pre-expander, manufacturer Dae Kong, type DKF 3600, with material feed, flow bed dryer, sieve, automatic weight control, control Siemens, Discharge capacity 20g/l ---- 2000 kg 17g/l -----1700 kg the pre-expander is in very good condition.

used BMB 220T KW22PI/700. Screw diameter: 50 mm Injectable volume: 422 cm3 Passage between columns: 560 x 510 Moulded thickness: minimum: 200mm- max: 600 mm Opening stroke: 600 mm

used BMB 350T KW35PI/2200. Screw diameter: 65 mm Injectable volume: 1138 cm3 Column passage: 710 x 630 mm Moulded thickness: minimum: 250 mm- maximum: 750mm Opening stroke: 750 mm Robot interface: E67 Blow Guns

used NETSTAL SYNERGIE 3500/2700. Screw diameter: 70 mm Injectable volume: 1077 cm3 Injection pressure: 2423 bar Passage between columns: 720 x 720 Moulded thickness: minimum: 450mm- max: 750 Opening stroke: 700 mm Number Of Cores :2

used HAITIAN JU10800H. Screw diameter: 110 mm Injectable volume: 4847cm3 Injection pressure: 1892 bar Column passage: 1270 x 1100 mm Moulded thickness: minimum: 500mm- max: 1200 mm Number Of Cores :4 Robot interface: E67 Servo motor

used BILLION H 1300/400 DIXIT III. Screw diameter: 55 mm double thread Injectable volume: 582 cm3 Injection pressure: 2200 Column passage: 780 x 780 mm Moulded thickness: minimum: 760mm- maximum: 1190 mm Opening stroke: 760 mm Number Of Cores :2 Robot interface: E67 36 heated zones

used BILLION GM 4200/750 DIXIT II. Screw diameter: 90 mm Injectable volume: 2862 cm3 Injection Pressure: 1472 Column passage: 1100 x 1100 mm Moulded thickness: minimum: 450mm- max: 1200 Opening stroke: 1200 mm Number Of Cores :0 Robot interface: E12 28 heated zones

used BILLION GM 3500/430. Screw diameter: 75 mm Injectable volume: 1657 cm3 Injection pressure: 2121 bar Column passage: 820 x 820 mm Moulded thickness: minimum: 300mm- max: 850 mm Opening stroke: 950 mm Number Of Cores :3 Robot interface: E12

used BIPEL Twin 40T Press Hydraulic Press. Bed Size:Left to Right 393mm 15.5 in Front to Back 393mm 15.5 in Daylight Between Tables 559mm 22 in Daylight Between Heated Platens 353mm 13.9 in Heating Electrical Induction Heated Platen Sizes(Up To) 355mm x 355mm 14″x14″ Max Working Platen Temperature 220°C Main Ram Stroke(Up To) 355mm 14 in Hydraulic Circuit Pressure 70 Bars 1000 PSI Main Ram Pressing Force 41 T 40 Ton Main Ram pull back 2.2 T 2.2 Ton Closing Speed(Up To) 150mm/s Opening Speed(Up To) 120mm/s