subcategories
(3rd category level)
Manufacturer:
(Category: 107)
sheet width: 4040 mmplate thickness: 4,00 mmdistance between columns: mmtotal power requirement: kWweight of the machine ca.: 7,50 tdimensions of the machine ca.: mMotorized adjustable backgauge with digital display up to 1000 mmPneumatic sheet metal supportSide fence and table extensionsCut length limiterCut edge lightingThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
sheet width: 3100 mmplate thickness: 6,00 mmdistance between columns: mmtotal power requirement: kWweight of the machine ca.: tdimensions of the machine ca.: mMotorized backgauge with digital displayManual kerf adjustmentVariable cutting lengthCutting edge illuminationNew bladesThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
sheet width: 3100 mmplate thickness: 10,00 mmdistance between columns: mmtotal power requirement: kWweight of the machine ca.: 10,00 tdimensions of the machine ca.: mMotorized backgauge up to 1000 mm with digital displaySide fence and table extensionsCut length limiterCut edge lightingNote: Backgauge is slightly inaccurate (+/- 1 mm)The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
used
Large working width: 3050 mm for sheet metal (with a strength of 45 kg) up to: 6 mm Clear stand width: 3400 mm Cutting angle adjustable by hand: 0.5 - 3° Number of hydraulic hold-downs: 18 Stroke rate approx.: 9 - 17 /min Stop adjustment: 1000 mm Hydraulic drive: 380 V, 7.5 kW Space required incl. back gauge: 3600 x 1800 x 1580 mm Weight: 5200 kg
pressure: 60 tchamfer lenght: 2050 mmdistance between columns: 1550 mmthroat: 255 mmstroke: 165 mmdayligth: 475 mmworking feed: 9,8 mm/secreturn speed: 117 mm/secajustment speed: 150 mm/sectotal power requirement: 5,5 kWweight of the machine ca.: 5000 kgdimensions of the machine ca.: 2300 x 1500 x 2470 mmEquipment:- DELEM DA65 CNC control- Electric backgauge (X-axis), 600 mm- Hydraulic upper tool clamping- Front light barrier- Side and rear protective grilles- Manually adjustable stop bar, foldable (R+Z-axis)- Upper tool- 2x support arms- Machine feet- Operating instructionsThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Punching force: 350 kN (holes e.g. 23 m in 12 mm material) Cuts 150 x 10 mm on the flat steel shear Two separate footswitches for the punching and shearing side, so punching and shearing can be done independently Support table on the punching side with stop cam Range of tools is included in the price
sheet width: 750 mmplate length: 1250 mmplate thickness: 4 mmtable surface area: 1600 x 1050 mmno. of strokes: 180 Hub/minmax. punching diameter: 105 mmpunching pressure: 25 ttotal power requirement: 4,0 kWweight of the machine ca.: 1,8 tdimensions: 1,9 x 1,9 x 1,7 mPunching and nibbling machine- Digital readout for X and Y axis- Tool cabinet with toolsThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
sheet width: 1020 mmplate thickness: 2 mmdistance between columns: 1020 mmbending angle max.: 135 °total power requirement: 0 kWweight of the machine ca.: 0,3 tdimensions of the machine ca.: 1350 x 850 x 1175 mMax. bending angle 135°Manually operated with auxiliary spring on both sides.Upper beam opening 40 mm,Upper and lower beams segmented,Segment division: 25-30-35-40-45-50-75-100-150-200-270 mmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
MITSUBISHI ML3015eX PLUS laser cutting machine was built in 2019 in Japan by MITSUBISHI ELECTRIC CORPORATION. The machine, distinguished by the use of the most advanced technology available on the market, is an excellent choice for precision cutting of sheet metal made of, among others, steel, aluminium and copper. Workpieces with a maximum length of 3050 mm and a width of 1565 mm are machined by means of a reliable head with auto focus, which is powered by a 4.5 kW laser beam. The laser beam is generated by electrical discharges in a special gas mixture with a relatively slow flow and in a direction perpendicular to its axis. Real-time power monitoring, combined with a constant beam length, ensures the highest cutting quality over the entire work area and prevents power deviations of more than ± 1%, which are necessary for machining highly reflective materials. The entire machining ...
Offer 25311 Specifications: - Cutting length 250 mm - Cutting angle 90 ° - Cutting thickness - normal steel up to 4 mm - Stainless steel up to 3 mm - Aluminium up to 5 mm - Stroke rate up to approx. 55 /min - Table size W 800 x D 800 mm - Working height approx. 940 mm - Stops infinitely adjustable in length and number of degrees - Drive 400 V / 4 kW - Oil filling 50 l - E - Footswitch - Space requirement approx. W 1300 x H 1250 x D 1300 mm - Weight approx. 800 kg - Mobile undercarriage
plate thickness: 4 mm STplate thickness: 3 mm VAblade length: 225 mmengine output: 3,5 kWweight of the machine ca.: 650 kgdimensions of the machine ca.: 1250 x 900 x 1100 mmFeatures:- 2x miter stops- 90° fixed angle- Foot switchThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Max. bending length: 1270 mm Max. sheet thickness: 1.75 mm steel Motorized upper bolster adjustment via foot switch Automatic backgauge
Max. bending length: 3200 mm Max. sheet thickness: 4 mm steel Motorized backgauge with hinged cams up to 2500 mm with stop extension (disassembled) Motorized bending beam adjustment Multibend 9001 controller Segmented upper beam tool with automatic tool clamping (height 100 mm) Operating instructions Weight: 5800 kg
: 3050 mm: 12,0 mm: -: 0,5-3,0 °: 1000 mmtable height: 930 mmwork height max.: 930 mmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
KIMLA POWERCUT LF1020 fiber laser was built in 2022 in Poland by POLCOM Przemysław Kimla. The machine has worked for a total of 814 hours and is in very good condition. Laser cutting is performed by means of a stable 2 kW fibre beam, which is generated by a resonator of the highest energy efficiency. A focusing lens system inside the cutting head ensures optimum beam geometry for various types of workpieces. As a result, the edges of the machined workpieces are distinguished by their unprecedented smoothness and absence of irregularities. The entire machining process is fully automatic, thanks to the use of an automatic pallet exchange system. This system enables simultaneous loading and unloading of workpieces during cutting, thus increasing production efficiency and reducing machine downtime to a minimum. The POWERCUT LF1020 fibre laser is offered with an extensive range of equi ...
JORDI PHE-30180 CNC hydraulic press brake was built in 2013 in Spain by JORDI UNIVERSAL V.S.L. The machine, designed for precision machining of sheet metal with a maximum length of 3550 mm, is an excellent choice for any industrial plant. The combination of a high press force of 175 tonnes and an extremely stable design guarantees the best bending results, even during the most intensive challenges. All this is complemented by an intelligent CNC control with all the necessary functions. The PHE-30180 CNC press brake weighs 11000 kg. Technical specifications of the JORDI PHE-30180 press brake - CNC controller: ESA 530 - maximum press force: 175 t - maximum sheet metal length: 3550 mm - maximum slider stroke length: 265 mm - distance between columns: 2600 mm - top tool weight: 55 kg - bottom tool weight: 66 kg - light curtains - foot switch control - oil tank capacity: 250 l - ...
x-travel: 1000 mmy-travel: 600 mmz-travel: 600 mmcontrol: Heidenhain TNC 426spindle nose: 100-700 mmwork table:: 1.080 x 580 mmworkpiece weight max.: 550 kgT-slots: 7 Stk.T-slot - width: 14 mmtool piece magazine with: 36 Plätzenweight of tools max.: 8 kgtool length - max.: 340 mmtotal power requirement: kWweight of the machine ca.: 6,2 tdimensions of the machine ca.: 4.790 x 5.330 x 2.905 mmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
used Forstner slitting line, control left, 0-line right, with motorized cross shear, Machine is repaired, checked, cleaned by a specialist and is then fully functional. Test run was carried out. Working width: 250 - 1250 mm Sheet thickness steel: 1.5 mm Sheet thickness aluminium: 1.5 mm Colour: blue/yellow Total power requirement: 400 V Machine weight: 775 kg Dimensions: 1500 x 2200 x 1500 mm Coil weight: 2 t without straightening rollers Number of blades: 5 pairs Knife shaft diameter: 100 mm Speed: 25 m/min without bevel cut Coil width (max.): 1250 mm Maschinennummer/Machine number 102728 MST
SENTE MAKINA HDTF-SI tube forming machine was built in 2022 in Turkey by SENTE MAKINA İNŞ. SAN. VE TIC. LTD. ŞTI. The machine is used in the HVAC industry for the production of precision ventilation ducts, compliant with Eurovent and Smacna standards. Spiro ducts are created from thin sheets of metal with a maximum thickness of 1 mm. The innovative cutting system eliminates the noise and hot sparks typical of traditional saws, guaranteeing smooth edges without the need for additional deburring. The HDTF-SI duct forming machine weighs 2480 kg. The SENTE MAKINA spiral duct machine is fully complete and consists of the following components: – main frame – sheet metal decoiler – forming heads (2 pcs.) – cutting system – stitching roller system for different sheet thicknesses – unloading table (2 pcs.) Technical data of the SENTE MAKINA HDTF-SI spiral tube machine ...
AMOB MAH 40/3 CNC 3-roll bending machine was built in 2021 in Portugal by AMOB Group. The machine, designed for bending tubes and profiles, ensures the highest precision and repeatability of the produced parts. The machining process is performed by three hardened rollers, of which the upper roller has hydraulic adjustment. Each of these is driven by a reliable, high-power motor, which is located inside a fully welded body. This solution enables bending of even the most complex shapes both vertically and horizontally. All this is complemented by an advanced CNC control with memory for numerous programmes. The MAH 40/3 CNC tube and profile bending machine weighs 540 kg. Technical specifications of the AMOB MAH 40/3 CNC bending machine - control panel with CNC control - number of rollers: 3 - roller diameter: 148 mm - roller rotational speed: 12 rpm - number of shafts: 2 - shaft di ...
Ref. No. 00891 Name of the Tube Laser Cutting System Manufacturer: BLM Adige Model LT 652/B Year of construction 2002 Laser power 2000 watts Loading length Unloading length Loading length 6500mm and unloading length 3500mm. In 2024, 40,000 euros were invested Operating hours 3 shifts Computer 127,653h Heating HF tube 62.850 h High voltage 119,453 h From order confirmation at the time of purchase Lasertube LT652 Automatic feeder for pipes between 3200 and 6500mm Fully automatic pipe support and unloading device for pipes up to 4500mm Siemens Sinumerik 840D control system Teleservice incl. modem CO2-Slab-Laser Model DC020 Kompakt, Fabr. Rofin Sinar Hamburg Integration RF DC020 Compact Laser Cooling Unit Fine dust filter, Fabr. Donaldson Torit Universal AK-HP Cutting Head, Fabr. Precitec Gaggenau Precitec Interchangeable Cassettes AK-HP 5" HP ZNSE 5" ...
Machine Type: Punching/Nibbling Machine Manufacturer: EDEL Type: Micromat 205 Year of manufacture: coming soon Condition: used Offer will only be sent if a complete imprint is provided! Price VB Location Warstein , Germany Reference M-EDE-0925 DESCRIPTION We offer you a used punching / nibbling machine from the manufacturer EDEL. Available now Technical data and accessories will follow! Our offer is aimed at tradespeople who are registered within the meaning of the Trade Regulation Act according to §14 GewO. The offer is subject to change, subject to prior sale. Please provide your full contact details to receive a quote with our terms and conditions of payment. Errors in the descriptions and offers are reserved!
Bending length / working length 2,500 mm Press force / bending force 1,500 kN (≈ 1500 kN) Max. sheet thickness (steel) approx. 2.0 mm Max. sheet thickness (aluminium) approx. 3.0 mm Max. sheet thickness (stainless steel / higher tensile strength) approx. 1.25 mm Max. bending height approx. 300 mm (depending on model) Power / Capacity (Electrical) 24 kW Machine dimensions: 4,050 × 1,600 × 2,400 mm Weight ~ 13,000 kg
FOBA FD84S Sensor for YAG Laser Marking System For sale is a used FD84S sensor from the manufacturer FOBA. The sensor is intended for use in YAG laser marking systems. Technical details: Manufacturer: FOBA Model: FD84S/S50 Design: Sensor / Laser Control Component Laser class (system use): 4 Wavelength: 1064 nm Laser power (system use): 70 W Pulse power: 10 kW Pulse duration: 70 ns Application: Spare part / component for FOBA laser marking systems Condition: Used, functional Buy FOBA FD84S sensors and other items at low prices – Here you can buy goods from the professionals for the professionals – In our SHOP you will find more attractive offers.
Travel: X-axis (mm) 3060 Y-axis (mm) 1530 Z-axis (mm) 160 Max. dimensions sheet metal (mm) 3048×1524 Control: Sinumerik 840D SL Power of laser: 2000W Max. sheet thickness: steel 12 mm Stainless steel 6 mm Aluminium (AlMg3) 6 mm Copper 3 mm Brass 3 mm with loading and unloading system for the sheet metal
Inv. Num. : 8711 Type: MG 2000 x 25/20 Producer: Maqfort Created: 1998, GO 2016 Parameters: Working length rollers: 2000 mm Max. sheet thickness: 25 mm
A Dimeco Alipress coil-to-sheet line with decoiler, straightener, and shear is available. Sheet width range: 200mm-1300mm, sheet thickness range: 1mm-7mm, cross-section range: 1400mm²-3250mm², max. feed speed: 30m/min, max. stroke rate: 150/min, max. material feed: 1000mm/stroke, straightener: Schechtl MSB100. Documentation available. An on-site inspection is possible.
Punching force: 300kN, max. operating pressure: 300bar, weight: 13500kg, operating hours: approx. 52300h. Documentation available. An on-site inspection is possible.
Pressing force: 2000kN, working length: 7200mm, connected load: 15kW, max. oil temperature: 45°C, max. operating pressure: 200bar, max. material thickness S235: 8mm, max. stroke: 215mm, max. closing speed: 200mm/s, pressing speed range: 1mm/s-10mm/s, stop time: 90ms, safety distance: 290mm, weight: approx. 38000kg. Including underfloor equipment and Fiessler AKAS 160 S safety system, year of manufacture: 2013. Documentation available. An on-site inspection is possible.
