gear cutting and hobbing machines used for sale

Various sizes, please note! Without pallet

Workpiece diameter maximum: 500mm, Equipped with: adjustable table, Number of operating hours: 5190 hours.

Control voltage: 220 V. Three-phase current: 50 Hz, Circuit diagram: 127.88.002.00.8,

Various sizes, please note! Without pallet

max. wheel diameter:80 mmmax. module:3 total power requirement:25-35 kWweight of the machine ca.:10 tworkpiece weight:15 kgworkpiece length - max.:-50+450 mmtable diameter:145 mmdiameter of hob:90 mmcutter length max.:220 mmhob turning speeds:1.000 U/min

rolling capacity max.:6,1 tworkpiece diameter:160 mmworkpiece length:25 mmtotal power requirement:14 kWweight of the machine ca.:4000 kgsdimensions of the machine ca.:2,5 x 2,5 x 2,1 mInternal rolling machine for transmission shift sleeves

max. wheel diameter:300 mmgear width:100 mmmax. module:5 workpiece turning speeds:0 - 1000 1/minwork piece - max.:1100 mmworkpiece clamping:auto. tension device number of spindle speeds:1000 1/min.spindle bearing diameter:100 mmdiameter of spindle flange:120 mmtailstock travel:80 mmweight of the machine ca.:3500 KGdimensions:1200 x 1450 x 2250 mmtotal power requirement:10 kVAThe Gear Tooth Deburring machine WERA, ZEM 300 for deburring of splines gear wheels and shafts, with Pointing Facility.

max. wheel diameter:200 mmgear width:250 mmmax. module:3 min. module:0,5 total power requirement:45 kWweight of the machine ca.:8,5 tdimensions of the machine ca.:4,4 x 2,4 x 2,7 mMachine out of prototype productionWithout automation

grinding wheel diameter:400 mmtotal power requirement:3 kWweight of the machine ca.:1,5 tdimensions of the machine ca.:1,5 x 1,4 x 1,3 mDressing Grinder for gears REISHAUER AMmax. width of grinding wheel 104 mmmax. dia. of grinding wheel 400 mmmax. module 7min. module 0,5pressure angle 10 - 30 °grinding worm dia. 270 - 400 mmwidth of grinding worm 62/84/104 mmgrinding worm turning speeds: at profiling 18/35/70 U/minelectrics - voltage/frequency 380 / 50 V/Hzlong. movement of crowning device 156 mm

control:siemens 1P 6SL 3054--0CE01-1AA0 Documents:vorhanden

frequency:5.000-150.000 Hzweight of the machine ca.:10 tZ-axis:45-50 mmX-axis:pneumatisch working lenght:45-50 mmwith induction generator Sinak 100PH CN: 26811/100014 built in 2006 with belt filter press Heat exchanger and hydraulic unit

weight of the machine ca.:8 tdimensions of the machine ca.:2,95 x 1,6 x 2,36 mchucking diameter:250 mmswing diameter:265 mmx-travel:170 mmz-travel:200 mmspindle turning speed range:1.500 U/minspindle bearing diameter:100 mmPick-up machine

weight:22 t

max. wheel diameter:40-320 mmgear width:90 mmmax. module:3,5 min. module:1,25 weight of the machine ca.:5,6 t

max. wheel diameter:200 mmgear width:250 mmmax. module:3 min. module:0,5 total power requirement:45 kWweight of the machine ca.:6,5 tdimensions of the machine ca.:4,4 x 2,4 x 2,7 mMachine out of prototype productionWithout automation

max. wheel diameter:40-200 mmtotal power requirement:31,3 kWweight of the machine ca.:4 t

max. wheel diameter:130 mmgear width:170 mmmax. module:3 min. module:0,5 total power requirement:48 kVAweight of the machine ca.:9 tdimensions of the machine ca.:7,64 x 3,14 x 3,25 mFor technical data, see PDF-File enclosed

max. wheel diameter:275 mmgear width:55 mmmax. module:6,5 min. module:1,5 Face Hobbing-Continious ProcessContinuous process: The workpiece and tool (usually Spiron) rotate at the same time, and all teeth are created in one operation at the same time. Knife head has several knife groups (not arranged in a circle) Parallel tooth Conical tooth tip surface Single Item procedure: The workpiece is stationary and the tool (usually Arcon) rotates and cuts a tooth by immersing the tool. Once a tooth is cut, the tool moves out of the tooth again, the workpiece divides by one tooth width and the next tooth is cut until all teeth are finished. Knife head has arranged all knives in a circular path. Conical tooth height Parallel tooth head surfaceC28 can do both, wheel + pinion. However, a C28 must be ?prepared? for the individual part procedure. I.e. direct measuring system + part gear brake, workpie ...

max. wheel diameter:275 mmgear width:55 mmmax. module:6,5 min. module:1,5 Face Hobbing-Continious ProcessContinuous process: The workpiece and tool (usually Spiron) rotate at the same time, and all teeth are created in one operation at the same time. Knife head has several knife groups (not arranged in a circle) Parallel tooth Conical tooth tip surface Single Item procedure: The workpiece is stationary and the tool (usually Arcon) rotates and cuts a tooth by immersing the tool. Once a tooth is cut, the tool moves out of the tooth again, the workpiece divides by one tooth width and the next tooth is cut until all teeth are finished. Knife head has arranged all knives in a circular path. Conical tooth height Parallel tooth head surfaceC28 can do both, wheel + pinion. However, a C28 must be ?prepared? for the individual part procedure. I.e. direct measuring system + part gear brake, workpie ...

workpiece diameter:38 mmworkpiece length:500 mmrack milling length - max.:610 mmprofile width:92 mmmodule range:0,3-1,3 slide stroke:760 mmdrive motor: kWelectrics - voltage/frequency:380/50 V/Hztotal power requirement:24 kWweight of the machine ca.:10 tSpline/cold Rolling Machine EX-CELL-O XK 251 with automatic loading device FELSOMAT PE03, fitted in 1999 and tailstock.A cold rolling machine, intended for non-cutting shaping of profiles, such as plug type gearing (straight or diagonal), spiral gearing, oil grooves

workpiece diameter:38 mmworkpiece length:500 mmrack milling length - max.:610 mmprofile width:92 mmmodule range:0,3-1,3 slide stroke:760 mmdrive motor: kWelectrics - voltage/frequency:380/50 V/Hztotal power requirement:52 kWweight of the machine ca.:10 tSpline/cold Rolling Machine EX-CELL-O XK 251 with automatic loading device FELSOMAT PE03, fitted in 1999 and tailstock.A cold rolling machine, intended for non-cutting shaping of profiles, such as plug type gearing (straight or diagonal), spiral gearing, oil grooves

max. wheel diameter: mmgear width: mmweight of the machine ca.:7000 kgdimensions of the machine ca.:9130 x 3895 x 3450 mmmax. top circle diameter:80 mmmax. length of teeth cutting:170 mmTotal length:240 mmtaper diameter:32 mmslide travel radial ( X-axis ):100 mmslide travel tangential ( Y-axis ):160 mmaxial movement Z-axis:300 mm/minworkpiece spindle - bore:45 mmelectr. connected load:44 kVA

weight of the machine ca.:4 t

total power requirement:413 kWInduction hardening machine Rotary table Eldec: Z (servo drive 750 mm Y (electromechanical) 300 mmX (electromechanical) 200 mmMaximum part diameter 600 mmMaximum workpiece weight 500 kg High frequency generator type HFG 200 Medium frequency generator type MFG 30

max. wheel diameter:280 mmmax. module:7 weight of the machine ca.:13 ttable turning speeds:100 U/mintable diameter:250 mmmin. number of teeth:4 hob turning speeds:1500 U/minmax. hob diameter:160 cutter length max.:230 mmMachine in good condition.Available 01.08.2024

max. wheel diameter:200 mmgear width:60 mmmax. module:7 weight of the machine ca.:15 ttable diameter:180 mmtable turning speeds:100 U/minhob turning speeds:750 U/minMachine in good condition, without feed, without automationAvailable 24.08.2024

max. wheel diameter:900 mmCounter holder milling mandrel is missing