machines and plants for waste disposal and recycling used for sale (1,306)

used Klanke RGS50 Roll splitter guillotine reel splitter roll cutter. Roll splitter RGS50 -Used machine- Good condition - ready for immediate use partially overhauled: Hydraulic hoses renewed Hydraulic oil change carried out Safety valves retrofitted Control overhauled Surround renewed Knives renewed Knife length 2500mm Max opening 1600mm V-table version Drive power: 15kW with soft start Dual pump with 2 stages cutting speed Two-handed operation Emergency stop cable on both sides Base frame and feed table available

used RUF + Co RUF 5.5/3700/60X40. For sale is a RUF 5.5/83700 with 60x40mm briquette size used for steel. Machine is in very good condition. Power requirement is 400V AC 11kW 32Amp. Control system is Siemen's S7-200

used Sant Andrea Novara 40/750. AG

used Doppstadt AK 565 Eco Power. Fine shredder Doppstadt AK 565 EcoPower used Model: AK 565 EcoPower Year of manufacture: 05 / 2021 Build No.: 1550 Operating hours: approx. 2,700 hours Availability: by arrangement Equipment: - Mobile shredder, mounted on a central axle trailer chassis for 80 km/h according to StvZo with ABS - Total weight approx. 19,000 kg - Mercedes/MTU diesel engine 6R1300, 390 KW at 2,000 rpm, meets EUROMOT IV emission standard - Fuel system 600 liters - Load-dependent control of the material feed via scraper floor - Aggressive feed roller: length 1,690 mm, diameter 510 mm, with attached toothed elements - Four-row flail drum with 36 free-swinging cast steel flail holders and interchangeable DoppLock flail tips - Centrally located lubrication strips - Electric pump for operating the cylinder functions (raise/lower support leg, open/close re ...

used Willibald Shark 5500. Fine Shredder Willibald Shark 5500 used Model: Shark 5500 Series 1 Year of Make: 2015 Build No.: 162 Operating hours: approx. 2,600 hours Availability: by arrangement Basic equipment: - Mobile shredder, mounted on a central axle trailer chassis for 80 km/h according to StvZo with ABS - Total weight approx. 19,000 kg - MAN diesel engine 353 kW (480 hp) - 40 free-swinging mallets - Neodymium magnetic roller - Hydraulic drive - Radio remote control Condition of the machine The machine is in a technically and visually good condition and ready for use. Warranty: The machine will be sold in the condition existing at the time of delivery. The seller assumes no liability for defects.

used WMS WMSII Sainless Steel. Scrap metal sorter specifically VA Stainless steel or all metals, Slag Ready for testing Software Update 2009-2016

used TECNOECOLOGY Junior 25. AGICOM Recycling Machine Trade The Junior 25 cable peeler is a compact tabletop device. The machine is ideally suited for extracting copper from the thinnest electrical cables (with rubber or PVC jacket). Peeling range: 2 to 28 mm Cutting speed: approx. 25m/min. Power consumption: 220V/440Watt Dimensions: 450x500x500 mm Easy adjustment and operation, Cutting Unit: Two-Knife System Weight approx. 50 kg; Year of construction 2020

used TECNOECOLOGY TR 250. AGICOM Recycling Machines

used JMC Mcintyre JMC 500 GT. AGICOM Recycling Machines Very powerful and high-quality alligator shears with a cutting force of up to 90 tons. The scissor head is operated with a foot pedal for individual cuts or continuous cutting and is protected by a safety cage. Cutting force: 90 tons Knife length: 508 mm Max. knife opening: approx. 250 mm Drive: 7.5 kW/380 V Overall dimensions: 1370 x 720 x 1280 mm Total weight: approx. 1020 kg Drive: 7.5 kw / 380 V Number of strokes at full opening: 16 / min Operation: Foot pedal; Machine on wheels Operating instructions in German CE Declaration of Conformity Spare parts available

used TECNOECOLOGY SRL TG500. AGICOM Recycling Machines

used Sant Andrea Novara 40/750. AGICOM recycling machines

used EMILOS 1200 Ecosystem. AGICOM recycling machines: Used vibratory screen 1200 ECOSYSTEM, overhauled by the manufacturer. Working diameter approx. 1200 mm. Perforated screen thickness: 0.800 mm Completely made of stainless steel Icon Video

used TECNOECOLOGY Maxi 100. AGICOM Recycling Machine Trade The powerful and robust MAXI 100 cable peeling machine is ideal for processing cables with a diameter of 6 to a maximum of 90 mm. How do you peel cables? The two-knife system cuts open the cable insulation, and the copper or aluminum core can be easily removed. The cable peeling machine can be infinitely adjusted to all cable diameters via a hand crank. The cutting depth of the blades (cable sheath) is also adjustable and thus enables the processing of a wide variety of cable types (e.g. triangular wires made of high-voltage cables, cables with lead sheath ...) All-round intrusion protection CE Declaration of Conformity Manual in German Spare parts available! Cable diameter: 6 to 90 mm Number of blades: 2 Cutting speed: approx. 22 m/min Drive: 2 electric motors, 2 x 1.1 kW / 380V 50 Hz Dimensions: L 1850  ...

used IRS SRL EASY 180. AGICOM Recycling Machine Trade The Easy 180 cable pelletizing system is the ideal entry-level model for professional cable recycling. This one-man machine is thrown in by hand. Pre-shredded cable material or uncut cables are thrown in. The Easy cable pelletizing system is very robust, powerful and delivers the best results from old and residual cables. The machine is characterized by: Compact design Low space requirement Easy to use Low energy consumption Operating instructions in German Spare parts (knives, perforated sieves) available Technical data Feed material: Electrical cable without impurities Throughput capacity: up to 180 kg/h Drive: 8.5 kW Weight: approx. 1200 kg Dimensions: approx. 1700 x 1300 x 2100 mm

used Lefort Conkest mobile 500. For sale is a robust Conkest Mobile 500 machine. We have collected this machine, however, it has sustained fire damage. Our plan is to carry out a comprehensive package of work to restore its mobility and replace many of its worn and damaged parts. Key Advantages and Features: Radio Remote Control: The unit can be fully operated via a radio remote control, providing exceptional flexibility, convenience, and safety for the operator. Thanks to remote operation, machine movement and workflow management can be carried out precisely from an optimal viewpoint and a safe distance within the work area. Important Note Regarding Photos: Please note that the attached photographs show the machine in its previous, pristine condition and do not reflect its current fire-damaged state. This machine provides an excellent foundation for a complete restorati ...

used Lefort trax 600. For sale is a high-performance, industrial-grade Trax 600 shear baler. This machine is expertly designed for the efficient compaction and size reduction of various metal scrap types, structural steel, and light plates. Key Technical Specifications and Features: Type: Trax 600 Shear Baler Year of Manufacture: 2021 Serial Number (SN): 1459 Operating Hours: 4,871 hours (as of August 19, 2026) Application: Engineered for the continuous processing of mixed metal scrap, light sheet metal, and industrial steel scrap, featuring high pressing and cutting force. Availability and Schedule: This equipment is scheduled to be taken back in part exchange at the beginning of December 2026.

used Lefort Conkeror 650. Make and Model: Lefort Konkest 650 (currently designated as the Konkeror 650), the entry-level model of the manufacturer’s uniform monobloc product range. Year of Manufacture and Delivery: 2023 Expected Availability: Early 2027 (taken as a trade-in due to the delivery of a new machine). Operating Hours: Approximately 5,000 operating hours (the machine had 4,349 hours on March 10, 2026). Condition: Excellent, continuously maintained, and in immediate working condition. Cutting Force: 650 tons, featuring the latest shear head design. Compression Box: 6.0-meter folding compression box. Power Unit: Reliable Perkins 275 horsepower diesel engine, enabling fast and flexible installation across most sites. Applicability and Efficiency This equipment is specifically designed to be an ideal addition to smaller metal scrap p ...

used PAAL KONTI 325 G/S/k. Fully automatic baler Manufacturer: PAAL Type KONTI 325 G/S/k Operating hours: approx. 39,000 h Year of Make: 2012 Technical manufacturer data: Pressing force: 990 kN at 300 bar Specific pressing pressure: 120 N/cm² Drive power: 2 x 55 kW Pump capacity: 2 x 370 l/min. Total connected load: 150 kW / 260 A Volume output at idle: 800 m³/h Volume capacity at 35 kg/m³: 390 m³/h Performance at: 35 kg/m³ bulk density: approx. 13.50 t/h 60 kg/m³ bulk density: approx. 21.5 t/h 100 kg/m³ bulk density: approx. 33 t/h Filling opening: 1,020 x 1,750 mm Bale size: 750 x 1,100 mm Binding: 5-fold vertical + 3-fold horizontal Machine weight: approx. 28 t Bale weights: 525 to 800 kg including: - Free kicks - Wirbulator 15 kW - Automatic 3-fold horizontal tying with 40 kg w ...

used Goudsmit Magnetic Systems Eddy Current REC-08. AGICOM recycling machine trade: Used eddy current separator Eddy Current from Goudsmit. The Eddy Current non-ferrous separator is intended for the separation and recovery of non-ferromagnetic metals (e.g. aluminium and copper) from non-adherent material streams. The separation process of the Eddy Current non-ferrous separator is based on the so-called "eddy current principle". When electrically conductive materials are exposed to a rapidly changing magnetic field, current is induced. Such eddy currents create a magnetic field that is opposed to the changing magnetic field of the magnetic roller (the output magnet). Electrically conductive particles passed over such a magnetic roller are therefore repelled by the changing magnetic field. The non-electrically conductive materials fall off after passing through the magnetic roller.  ...

used HSM VK 8818 R-FU. Technical data press: Manufacturer HSM GmbH + Co. KG, Germany Type VK 8818 R-FU Year of construction 2010 Operating hours 3,817 hours, as of August 2026 Number of bales pressed 36,001 bales, as of August 2026 Press force main press 1000 kN Specific pressing force 120 N/cm² Press force cutting edges free kick 121 kN Dimensions of the insertion tray 970 x 1,800 mm Theoretical cycle time in idle mode 8.3 seconds Theoretical throughput 643 m³/hour Bale dimensions 1,100 x 750 mm, the length is variable 600 to 2000 mm Drive power 2 x 45 kW, frequency-controlled Connected load 110 kW Current consumption, total 213 A Fuse 250 A slow blow Tying 5-fold horizontally, fully automatic throughput capacities with a Bulk density of 20 kg/cbm 12.86 t/hour Bulk density of 50 kg/cbm 32.15 t/hour Bale weights with a bale length of approx. 1.2 m 650 up to 750  ...

used NEUE HERBOLD SM 600/1000-S7-2. Granulator, heavy-duty version Manufacturer: NEUE HERBOLD, D-74889 Sinsheim Drive: 75 kW Hopper: Conveyor belt hopper Working width: 1000 mm Rotor diameter: 600 mm Year of manufacture 2015, overhauled with - New rotor - New funnel - New base frame Application examples: Crushing of massive lumps, start-up chunks, profiles, beverage costs, boxes, vegetable crates,...

used Presto PZA. Technical data cardboard shredder (2-shaft shredder): Manufacturer: Presto GmbH & Co. KG Type PZA Year of construction 2007 (52,998 h and 55,325 h) Throughput volume 130 m³/hour Speed 37/9 1/min. Motor power 7.5 / 2.2 kW Electrical connection 32 A Dimensions shredder inside 1,490 x 1,320 x 530 mm (L x W x H) Dimensions shredder external dimensions without hood 2,308 x 1,320 x 685 mm (L x W x H) Machine weight 0.45 t Use of the systems: The 2 pieces of cardboard shredders of the type PZA were used in a Dutch logistics center to pre-shred loose, erected cartons from the returns department and then press them into bales. The cartons were fed by hand onto the feed belt and were transported directly to the carton shredder with a sliding belt conveyor belt and torn. The pre-shredded cartons were then transported over hundreds of meters to the baler and press ...

used Cross Wrap Oy BO 4000. Technical data of the bale opener line for RDF, MSW, paper, cardboard: Manufacturer Cross Wrap Oy Ltd., Siilinjärvi, Finland Type BO 4000 Year of construction 2015 Number of opened bales 674 pieces Operating time only 3 days, exclusively by running-in the entire system during new installation Opening time approx. 45 seconds per bale Bale dimensions (W x H x L) 1100 x 1100 x 1400 – 1900 mm Max. bale weight 2,000 kg Conveying height of the system 1,400 mm Max. conveyor width of the system 1,200 mm Openable material RDF/MSW Availability of the system 98% Noise level of the bale-opener line 85 dB(A) Total connected load 37 kW Rated current 125 A SIEMENS SIMATIC HMI Touch operating display Control SIEMENS S7 ET200S Dimensions 8,463 x 2,890 x 3,960 mm (L x W x H) Scope of delivery: Feed conveyor 3,500 x 1,200 x 1,400 mm Conveyor belt f ...

used Presto CC 36 M. Technical data press: Manufacturer: Presto GmbH & Co. KG Type CC 36 M Year of construction 2010 Operating hours 3,641 hours Press force main press 36 t Specific pressing force 467 N/cm² Dimensions of the insertion tray 1,080 x 1100 mm (L x W) Cycle time 34 seconds Filling volume / pressing cycle 0.85 m³ Theor. Throughput capacity 90 m³/hour Throughput under operating conditions with a material bulk density of 35 kg/m³ approx. 51 m³/hour Bale dimensions 1100 x 750 mm (W x H), length variable Drive power 15 kW Tying 4-fold vertical, semi-automatic, with polyester plastic yarn throughput capacities with a Bulk density of 35 kg/cbm 1.8 t/hour Bulk density of 60 kg/cbm 2.5 t/hour Bulk density of 100 kg/cbm 3.1 t/hour Transport dimensions excluding press 4,200 x 1,640 x 2,200 mm (L x W x H) Machine weight press approx. 4 t Remarks: The press  ...

used Paal Konti 600. Technical data press: Manufacturer Paal (Kadant Paal) Type Konti 600 Year of construction 2008 Total operating hours: 23,020 hours Effective operating hours 1st pump: 10,719 hours, as of August 2026 Effective operating hours 2nd pump: 10718 hours, as of August 2026 Effective operating hours 3rd pump: 9,766 hours, as of August 2026 Number of bales pressed 183,075 bales, as of August 2026 Press force main press 158 t Specific pressing force 12.83 N/cm² Filling volume 3.45 m³ Theor. Throughput capacity approx. 1,266 m³/h Throughput under operating conditions approx. 805 m³/h Bale dimensions 1,100 x 1,100 mm, length variable Drive power 2 x 75 kW Total connected load, 135 kW Bonding 5-fold vertical, fully automatic throughput capacities with a Bulk density of 35 kg/cbm approx. 28.2 t//h Bulk density of 60 kg/cbm approx. 45.6 t/h Bulk density o ...

used Lefort 800AS. This is a Lefort Mobile 800 shear baler designed for processing light scrap and car bodies. It is the AS variant, which means an asymmetric box where one side is higher than the other to fit in more scrap per load. Originally manufactured in 2006, this machine was factory refurbished in 2011, after which it was sold to the previous owner. We took it back in part exchange earlier this year and have prepared it for sale. The machine does require some refurbishment work and can be sold either as seen or with a package of work completed. For more information, please contact us.

used Lindemann SAS 1000. For sale is a fully operational, industrial-grade Lindemann SAS 1000 three-dimensional baler, offering reliable performance for scrap metal processing applications. Key Technical Specifications: Type: Lindemann SAS 1000 (Three-dimensional baler) Year of Manufacture: 1993 Drive System: 2 x 90 kW electric motors Cycle Time: 30 seconds Bale Size: 30 x 30 cm Control System: Modern touchscreen display Condition and Logistics Options: The machine is in fully working condition and was carefully dismantled solely due to relocation. We offer flexible delivery and handover options tailored to your needs: Standard Option: Provided in its current condition, loaded onto the buyer’s truck. Turnkey Option: Upon request, we can handle transport, professional assembly, and commissioning at the buyer’s site.

used Klanke RGS50 Supercut guillotine reel splitter roll cutter. Roll Splitter Guillotine RGS50 Used machine in good condition, partially overhauled immediately ready for use Year of Make: 2014 Drive power: 15kW Cutting force 2x25to Knife length: 2500mm Max aperture. 1600mm incl. base frame and feed table Work/feed height 1200mm Two-handed operation PLC supported

used UNOTECH UPAMAT 130 H5. automatic baler Manufacturer: UNOTECH Type: UPAMAT 130 H5 Year of construction 2025 Operating hours: approx. 1,300 h Technical data: Press force: 1,200 kN / 315 bar Specific pressing pressure: 10.00 kg/cm² Filling opening 2,000 x 1,020 mm Channel format: 1,100 x 1,100 mm (H x W) Bale weight: 800 - 1,100 kg (depending on material and bale length) Binding: 5 times horizontally seen in the direction of pressing on the right side Drive power: 1 x 75 kW Oil tank volume: 2,400 litres incl. oil drip pan and leak oil warning device Volume output: - at idle approx. 920 m³/h - Under operating conditions: approx. 410 m³/h Weight output depending on the bulk material: - For 20 to 30 kg/m³ bulk density: approx. 12 t/h - For 30 to 50 kg/m³ bulk density: approx. 20 t/h - At 60 kg/m³ bulk den ...

used MacPresse MAC 105. Coming soon Baler Macpresse MAC 105, press force 70 t, year 2011 Technical data: Manufacturer: Macpresse International S.R.L., Milan / Italy Type: MAC 105 Year of Make: 2011 Operating hours: as of 09/26: 23105 Pressing force: 70 t Drive power: 45 kW Mains voltage: 380 V / 50 Hz Filling opening: 1500 x 750 mm Bale chamber volume: 1.5 m³ Bale size: 1100 x 800 mm Throughput / mixed paper: 15 t/h Binding: 5-fold horizontal Transport dimensions: approx. 9,500 x 1,800 x 2,500 mm (L x W x H) Press weight: approx. 16,000 kg Accessories: Funnel Note: The press is expected to be dismantled in mid/late September and can be viewed in operation until then if desired. The conveyor belt seen in the photos is not included in the scope of delivery and can be purchased as an option. Please note: All technical data refer to the manufacturer's spec ...

used Doppstadt AK 310 Biopower. Very good condition, radio, drive, magnetic roller, rear belt, fine shredding basket 40mm for wood chips from pallets etc.

used Erema SW8 470 P/T. Erema SW8 470 P/T Plastic Recycling / Re-granulation Line Year: 1999 Make: Erema Model: SW8 470 P/T Erema Recycling Line • Make: EREMA • Type: SW8 470 P/T • Year of Manufacture: 1999 • Serial Number: C997043 • Weight: 3350 kg Technical Specifications • Designed for plastic film recycling and re-granulation • Includes extruder, cutter/compactor section, and downstream pelletizing equipment • Electrically driven system with integrated process control panel • Complete line as shown in photos Features & Equipment • Control cabinet with touchscreen interface • Feeding and cutting section with integrated motors • Vibratory cooling and pellet separation trays • Heavy-duty construction suitable for continuous industrial operation

used MACFAB BMF650 Auto HT RAL - MM9.8. Baler, MACFAB, – used - : Price from location: 13.500.-€ (net)! Manufacturer: MACFAB Systems Ltd Type: BMF650 Auto HT RAL - MM9.8 Year of construction: 01/2020 Serial Number: MF J144 Weight: 1770 kg Operating hours: approx. 16h Automatic operation & "bale ready" display Horizontal door can be swivelled sideways Surface / Colour: RAL6018 Filling opening: 1,500x880x769mm (WxHxD) Abm. Press: 2,100x1,524x3,217mm (WxDxH) Former new price. 18.921.-€ Condition: The machine has only been used once for testing purposes. Available: immediately Location: 72336 Balingen

used Kleemann MC 110 Z. Mobile jaw crushing plant Kleemann Mobicat MC 110 Z Year of manufacture 2007 Operating hours approx. 8600 UVV up to 23 Crushing performance depending on material Approx. 330 t/h Accessories: Magnetic separator Feed size max. 1,050 x 650 mm Crusher inlet 1,100 x 700 mm Transport width 3,000 mm Transport length 14,900 mm Transport height 3,600 mm Transport weight 39,500 kg Price from location near Magdeburg

used Ludden and Mennekes SVS+KEV. Papildoma informacija — Naujas preskonteineris Ludden & Mennekes SVS11+KEV 1. Stationary Screw Compactor L&M SVS 11 Almost unused stationary (~ 1 month) screw compactor designed for filling compaction containers and/or other containers. The machine is built from a robust welded steel structure with continuously welded seams. Its low-maintenance screw compaction system is suitable for continuous feeding, and the compaction chamber does not require periodic cleaning. Main technical specifications Overall length 2,480 mm Overall width 1,660 mm Overall weight 2,300 kg Loading height 1,350 mm Feed opening 1,375 × 1,490 mm Screw diameter 750 / 500 mm Screw speed 17 rpm Drive power 11 kW Residual-current device / FL plug Type B / 300 mA 2. Hydraulic Container Coupling / Decoupling System Hydraulically operated coupling and decoupling sy ...

used Goudsmit Magnetics Eddy. AGICOM recycling machine trade: Used eddy current separator Eddy Current from Goudsmit

used ISVE MR2260. AGICOM recycling machines: The used single-shaft shredder MR2260 is a powerful and energy-efficient shredder for the pre-shredding of cables, electronic waste, waste plastics, wood and much more... It has two stator knives for better product quality and higher hourly output. The shredder is equipped with an electronic control system. This monitors the hydraulic feed and the cutting shaft. As a result, the single-shaft shredder rarely has to reverse and retains its high throughput. Machine pre-equipped for cooling Electric motor: Siemens 19.0 kW + 2.2 kW, 400 V Weight: approx. 1,800 kg Dimensions: approx. 1750 x 1300 x 1800 mm Capacity: max. 200 – 400 kg/hour Year of Make: 2019 Machine in good condition and ready for immediate use!

used EUROPRESS 6000 V5 Hakenlift. Fully automatic baler Manufacturer: EUROPRESS Type: 6000 V5 Hook lift mount Year of Make: 2013 Technical data: Pressing force: 60 t Main drive power: 2 x 22 kW Filling opening: 1,450 x 1,000 mm Bale size: 750 x 1,100 mm Binding: 5-fold vertical Machine weight: approx. 13,800 kg Bale weights: up to approx. 600 kg Transport height: approx. 2,587 mm Transport width: approx. 2,500 mm Transport length: approx. 6,645 mm Subject to errors in the technical data!

used HSM HL 7009 ST/A. Baler HSM, type HL 7009 ST/A, year of construction 2021 Technical data: Manufacturer: HSM Type: HL 7009 ST/A Year of Make: 2021 Hours: 1118 Pressing force: 70 t Specific pressing force: 58 N/cm² Drive power: 11 kW Filling opening: 1020 x 900 mm Bale size: 1100 x 1100 mm (WxHxL) Bale weight: up to 600 kg Binding: 4-fold horizontal, manual Machine dimensions: 5992 x 2066 x 2394 mm (LxWxH) Weight: 7500 kg Materials: paper, cardboard, foil Note: The press is in good condition and has been inspected and tested by us. You can find a video on our website or YouTube channel. Please note: All technical data refer to the manufacturer's specifications. We assume no liability for the information provided or any errors. The offer is subject to change, subject to prior sale and can be revoked at any time. Visits are possible by arrangement. The sale ...

used Presto HPK 20/50 S. Channel baler Presto HPK 20/50 S, built in 2007 Manufacturer: Presto Type: HPK 20/50 S Year of Make: 2007 Operating hours: 10490 (as of 08/2026) Drive: 22 KW Press force: 50 t Filling opening: 1200 x 700 mm (LxW) Channel cross-section: 700 x 750 mm Filling volume, max. 0.63 m³ Cycle time: 23 s Binding: 3-fold, automatic throughput at 35 kg/cbm: 2.9 t/h 60 kg/cbm: 4.3 t/h 100 kg/cbm: 6.3 t/h Bale weight: up to 450 kg Machine dimensions: 760 x 1350 x 2350 mm (LxWxH) Machine weight: approx. 7,500 kg Materials: paper, cardboard, foil Note: The press is in good condition and is currently still in operation. A visit is possible by arrangement. The machine will be available from the end of 2026. Please note: All technical data refer to the manufacturer's specifications. We assume no liability for the information provided or any errors. ...