ID3353 Drilling rods 160 pieces of drill rods with 76 BOMAG thread – 2 meters 20 pieces of drill rods with 76 BOMAG thread – 3.5 meters 160 drill pipes with 76 BOMAG thread – 2 meters 20 pieces of boring rod with 76 BOMAG thread – 3.5 meters

existing pipes on the machine: COD91 - 3, 4M pipe, 50 pieces (200m), Engine/Type: John Deere 6068 HF 485, Power: 160 kW at 1500 rpm, Fuel: Diesel (tank capacity 600 liters), Compressor Type: Wabco, Max pressure:7.5 bar, Main winch cable Type: 19x7 swing arm, Diameter 6mm, Tensile strength 1960 N/mm2, Max pulling force 6 kN (600 kg), Tracked chassis Type:TG-12.0/SB1/600/11/3414, Length:3414mm, Width:2400 mm, Height:600 mm, Track width:600 mm, Swivel range:360°, Trolley cables Type: 6x36 WS + steel core, Diameter:14mm, Max load pull up:64 kN (6400 kg), Max load pull down :57.8 kN (5780 kg), (Main dimensions), Max length in transport position 8.65 m, Max width in transport position 2.50 m, Max height in transport position 3.10 m, Max working position length 7.88 m, Max working position width 2.50 m, Max height working position 9.79 m, Max turning radius 5.3 m, Spacing 2 outriggers for :198 ...

ID3354 Unimog - 4x4 year/Baujahr 1982 Unimog 4x4, Nordmeyer DSB 1 3/5 (combination drilling rig for dry and mud drilling), with piston pump with approx. 200 litres per minute for core drilling, with centrifugal pump for well drilling (supplied loose), two-stage power rotary head (450 daN - 175 revolutions/ 225daN - 350 revolutions), drilling diameter dry drilling max. 324mm, flush drilling max. 600mm in air-lift or suction flush drilling (additional equipment: drilling diameters up to 290mm are possible in rotary drilling), without casing machine Unimog 4x4, Nordmeyer DSB 1 3/5 (combination drilling rig for dry and flush drilling), with piston pump with approx. 200 l per minute for core drilling, with centrifugal pump for well drilling (loosely enclosed), power rotary head two-stage (450 daN - 175 revolutions/ 225daN - 350 revolutions), drilling diameter dry drilling max. 324mm, fl ...

Connected load: 55kW, weight: 6.8t.

ID2753 Müller MS16 HFV year/Year of construction 1999 approx. 3900 hours/hours 3.5 t Vibrator, with hydraulic unit MS-A360V, clamps MSU140 for steel sheet piles and 30 m of hydraulic hoses Vibrator, with hydraulic power unit MS-A360V, clamps MSU140 for steel sheet piles and 30 m of hydraulic hoses

Includes aggregate weigher, cement weigher, water weigher, additive weigher, special material weigher, Schlossermixer and Biotronik control system, documentation available, on-site inspection is possible.

ID2487 Eurodrill CDH 2400 year/Year of construction 2008 1.4 t Double-head drilling rigs, ready for use, little used (approx. 500 hours) Double-head drilling rig, ready for use, little used (approx. 500 hours)

1x hydraulic earth drill 945 € 1x auger 225mm 160€ 1x auger 300mm 190€ 1x auger 350mm 220€ 1x adapter, quick coupler MS-01 180€ 1x adapter, quick coupler MS-03 220€

ID2285 Clamp Rod Magazine/Rod Magazine Rod magazine for drilling rig, 3-shaft magazine Boom magazine for drilling rig, 3-bay magazine

Cone splitter JSK-350-MS01, splitting cone, drill cone, log splitter, 1x hydraulic earth boring device HBG-1500 (for mini excavator, tractor, front loader), 1x adapter, quick coupler MS-01 (for HBG-1500 and HBG-2000), 1x Jansen splitting cone, 1x jansen fixation adapter splitting cone

ID3092 Clamp KR803-3 year/Year of construction 2009 approx. 10420 hours/hours Drilling rig, hydraulic hammer 1215, RT70 insertion end, Deutz diesel engine TCD2013L042V, with additional short carriage (but without clamping device) Drilling rig, hydraulic breaker 1215, plug-in end RT70, Deutz diesel engine TCD2013L042V, with additional short mount (but without clamping device)

Diamond drill bit, core drill bit, 2 pieces, with 2x spline shaftPAGUSØ 40 / 50 mm drill bit 1: Diameter: Ø 40 mm ( 11/2 ( inches )), total length: 107 mm drill bit 2: Diameter: Ø 50 mm ( 2 ( inches )), total length: 107 mmspline shaft 1: Diameter: Ø 29 mm, length: 178 mmspline shaft 2: diameter: Ø 29 mm, length: 400 mmspline shaft profile: diameter: Ø 20 / 16 mm, length: 30 mm, 12 wedges, wedge width: 2.5 mmused, tested !Dimensions ( packaging ): 400 x 70 x 50 mm

ID3073 Atlas 1304 with Botec-Scheitza drill rig year/Year of construction 1990 13630 hours/hours 17 t Mobile excavator Atlas 1304 with Botec-Scheitza drilling mount for auger and down-hole hammer drilling (max. diameter 130 mm), without impact mechanism Atlas 1304 wheeled excavator with Botec-Scheitza drill rig for auger and down-the-hole hammer drilling (max. diameter 130 mm), without impact mechanism

Hammer drill, drillHILTITE 54 ( TE54 )Drilling capacity steel: 13 mmDrilling capacity concrete: 52 mm230 / 480 rpm900 W230 Vwith caseDimensions: 600 x 400 x 140 mm

ID2934 ABI TM10/12,5 year/Year of construction 1995 hours/hours 10000 Pile driver, ZR20T carrier, with MRZV 500V vibrator, with hydr. Auxiliary winch (tractive force 30 kN), with single tongs and storage frame, very good condition Piling rig, carrier device ZR20T, with vibrator MRZV 500V, with hydr. Auxiliary winch (pulling force 30 kN), with single pliers and storage frame, very good condition

Diamond drill bit, core drill bitHILTIDD-BI 25/280 RC ( DD-BI25/280RC )250900/8Ø 25 mmDepth: 280 mmNew !Dimensions (packaging): 350 x 40 x 40 mm

ID3337 Wassara Drilling equipment / Bohrausrüstung Drilling equipment (Wassara W150 water hammer), new price of the entire equipment approx. 50,000 euros Drilling equipment, (Wassara W150 water hammer), original price of all equipment approx. 50,000 euros

Diamond drill bit, core drill bitHILTIDD-BI 10/190 ( DD-BI10/190 )B18/512672Ø 10 mmDepth: 190 mmNew !Dimensions (packaging): 280 x 40 x 40 mm

ID3334 Rotomax XL GTI – Geothermal Drilling rig year/Baujahr 2020 approx. 7300 hours/hours 12.5 t Drilling rig, double rotary head 36000 Nm for boreholes up to 300 m depth, rubber tracks 450 mm, 6-cylinder diesel engine (205 KW) with particle filter, drill carriage with support plate (drilling pressure max. 4000 Kg, retraction max. 19000 kg, clamping head max. Diameter 219 mm, gear shift and gear swivel device, drill pipe catch clamp 419 mm, cable remote control, 4-gear protective tube drilling gear and 4-gear rod drilling gear, 240 kN shock tongs (80-419 mm diameter), cable winch, lubrication system double head system, trailer coupling Drilling rig, double rotary head 36000 Nm for drilling up to 300 m depth, rubber tracks 450 mm, 6 cylinder diesel engine (205 KW) with particulate filter, drilling rig with support plate (drilling pressure max. 4000 kg, retraction max. 19000 kg ...

Diamond drill bit, core drill bitHILTIDD-BI 14/280 ( DD-BI14/280 )B10/510574Ø 14 mmDepth: 280 mmused, tested !Dimensions (packaging): 400 x 40 x 40 mm

Drill bits for rock drills in different lengths

Drill head with cross edge, cross crown, drill bitBWS Ø 102.5 mmlength: 195 mm mount: spline shaft, 6 wedges, 10 mm widespline shaft diameter: 34 / 46 mmNew !Dimensions: 200 x 110 x 110 mm

ID3316 Unimog 437-40 year/Year of construction 1994 87,600 km Unimog 437-40 with Wirth ECO-0 drilling rig, Ingersoll-Rand 7-41 compressor (4350 hours), all-wheel drive, 324 mm casing rotary table, exchange gearbox, power rotary head, drilling diameter DN178 mm to DN324 mm Unimog 437-40 with Wirth ECO-0 drilling rig, Ingersoll-Rand 7-41 compressor (4350 hours), all-wheel drive, casing turntable 324 mm, exchange gear, power rotary head, drilling diameter DN178 mm to DN324 mm

ID3278 Mercedes Atego 1828 year/Year of construction 2003 6465 hours/hours 27.820 km Nordmeyer DSB 1/5 drilling rig, with centrifugal pump, on Mercedes Atego 1828 Drilling rig Nordmeyer DSB 1/5, with centrifugal pump, on Mercedes Atego 1828

Lots of monobloc boring bars Rock drills and extensions from tunnelling unused and used - Diameter: 23 to 83 mm - Length: 500 mm - 5600 mm Manufacturer: ROCBO, SANDVIK, BÖHLERIT u.a. Cone Boring Rods, Monobloc Boring Rods and Extension Boring Bars The drills come from the bearing dissolution of a tunnel construction company and are mostly as good as new. See list for details Changes and errors in technical data, information and prices as well as prior sale. Number Description Description Addendum 3 cone boring bars length approx. 4,000 mm inserting end approx. 25x159 mm, as good as new 1 cone boring bar length approx. 5,000 mm Inserting end approx. 22x82 mm, as good as new 2 cone boring bars length approx. 1,000 mm Inserting end approx. 22x82 mm, as good as new 25 cone boring bars length approx. 2,400 mm inserting end approx. 25x159 mm, as good as new 18 c ...

ID3274 Sandvik Ranger 500 with HLX 5 T Hammer approx. 6000 hours/hours Hammer approx. 3000 hours/hours Machine with fire damage, cabs burnt out, otherwise everything is in order Machine with fire damage, driver's cabs burned out, otherwise everything is fine

TOPHAMMER ENGINE - CUMMINS , 260hp,QSB6.7,Tier 4 COUNTRY OF PRODUCTION - South Korea DELIVERY - EXW

ID3265 Adler B50 year/Year of construction 2020 approx. 1500 hours/ hours 3.1 t Well drilling rig (well construction and geothermal energy up to 100 m), with trailer for drilling rig up to 3.5 t, standpipe with auger for pre-drilling, 110 m flushing drill pipe on steel pallet, complete maintenance was carried out at the end of 23. The machine was fitted with a new drill head from Eurodrill at the end of 2013 for approx. 20,000 euros. Water well drilling rig (well construction and geothermal energy up to 100 m), with trailer for drilling rig up to 3.5t, standpipe with auger for pre-drilling, 110 m directional drill pipe on steel pallet, complete maintenance was carried out at the end of 23. At the end of 23, the machine received a new drill head from Eurodrill for about 20,000 euros.

ID3208 Unimog 405/12 year/Year of construction 2000 10360 hours/hours – 71.100 km Unimog with Nordmeyer DSB 2/6 drilling rig, auger pump, overhauled in 2020, maximum crown load 100 kN, feed 60 kN, drilling cable winch 19 kN, power flushing head 7 kNm, crushing device 11 kNm, cable impact device (cable pulling force 30 kN, drilling load 5 kN, stroke 400 mm) Unimog with Nordmeyer DSB 2/6 drilling rig, screw pump, overhauled in 2020, maximum crown load 100 kN, feed 60 kN, drill cable winch 19 kN, power rinsing head 7 kNm, crushing device 11 kNm, rope impact device (rope pulling force 30 kN, drilling load 5 kN, stroke 400 mm)

The machine is already in Poland with us on site. , a drilling rig from the well-known Swedish brand Sandvik. Used for rocks mainly underground but can also work on the surface. This model is An excellent tool for securing high workings and tunnels, ensuring a safe working environment and constant access to the workplace. The universal screwdriver head design allows all common screw types and combinations to be used, with bolt lengths of up to 6 meters (20 feet), depending on the screwdriver head alternative chosen. The telescopic boom allows you to mount several rows of bolts without moving the machine. An optional second boom – screen holder or basket boom – increases productivity and versatility. Additional automatic functions allow the operator to focus on safe, fast and efficient rock reinforcement. The air-conditioned, soundproofed and tilting cab further enhances safety an ...