other machines for plastic used for sale (525)

Consists of: vacuum boiler, with agitator, temperature measurement, double-walled tank, can be heated, position detector, separation filter, vacuum valve, 1500ltr, vacuum pump, frame with recess for pallet forks, Content: 1.5 m³, medium: Water / Oil, test pressure: 5.6 bar(g), design temperature: 180 °C, pressure range installation: -1 to 10 bar, spiral (heat exchanger), capacity: 0.05 m³, medium: Cooling water / Steam, test pressure: 15.4 bar, Vertical cylindrical process tank made of stainless steel, mounted on a steel support frame, tank is equipped with an integrated heat exchanger (spiral) for temperature control of the product, on top there is an inspection/manhole cover and a drive for agitator or mixing device (if applied). A mechanical pump (vacuum or circulation pump) is mounted under the tank for product transport or process support. Auction-ID: A1-41983-119

Type: MSE, type: 063-008030-00, year of manufacture: 1992, medium: Air, density (ρ): 1,134 kg/m³, Inlet temperature: 20 °C, volume flow: 90 m³/min ≈ 5,400 m³/h, total pressure Δpt₂: 630 daPa, total pressure Δpt₁: 593 daPa, fan speed: 3000 min⁻¹, steel housing, radial impeller, axial inlet, radial exhaust, horizontal arrangement on frame with vibration dampers, Leroy-Somer LS160L engine, 18.5 kW, voltage: 380 / 400 / 415 V (Δ), frequency: 50 Hz, speed: 2930–2945 rpm, current: 32.6 – 34.3 A, protection class: IP55, insulation class: F, operation: S1 (continuous), Cos φ: 0.88 – 0.91. Auction-ID: A1-41983-106

Equipped with: 2 pieces Emo-G, with 2 pieces Piovan 10C vacuum loader, power: 3.0 kW, voltage: 220–240 V Δ, 380–420 V Y, approx. 12.1 A (Δ), approx. 7.0 A (Y), speed: approx. 2850 min⁻¹, IP55, insulation class: F, continuous (S1), vacuum range: ± -200 to -300 mbar, overpressure range: ± 200 to 300 mbar, oil-free operating system, 2x C10C vacuum loader / material transport unit, Stainless steel collection funnel with filter. Auction-ID: A1-41983-115

Consists of: 21 sieves, motor 0.75kW, supply connection 100mm, drain 50mm, compressed air connection with pressure regulator, main switch, cabinet for storage sieves, separation screen, see photos for Auction-ID: A1-41983-117

Consists of: including 4 pieces C10IX vacuum loader, 3x Piovan F48 side channel blower / side channel blower, power: 3 kW, voltage: 400V – 3-phase, vacuum: ± -250 to -350 mbar, air flow rate: ± 250–350 m³/h, 1x Piovan F44, side channel blower, 1.5 kW, 400V – 3-phase, vacuum: ± -200 to -300 mbar, air flow rate: ± 120–200 m³/h, 4 pieces C10IX (hopper loader) for pneumatic transport of plastic granulate, 230V (control + vacuum valve), capacity: ± 5–25 kg/h, filter unit with automatic cleaning, pneumatic vacuum valve system. Auction-ID: A1-41983-114

Equipped with: Chicago Blower, centrifugal fan / industrial blower, direct driven, steel impeller housing (heavy industrial version), square inlet with round discharge connection, mounted on steel frame with vibration dampers, suitable for industrial air and process air applications, TECHT TOP T3A132S1-2 motor, 5.5 kW, speed: 2930 rpm (50 Hz), voltage: 400V Δ / 690V Y (50 Hz), current: 10.0 A (400V) Protection class: IP55, insulation class: F, S1 (continuous operation, suction 150mm, exhaust 150mm. Auction-ID: A1-41983-108

Consists of: bore 38mm, total dimensions 850mm wide, 900mm high, 500mm wide, capacity: 27 m³/min, speed nominal: 2930 rpm, maximum: 3000 rpm, motor power: 5.5 kW, max. Valve speed 60 rpm, bulk density product: 1.22 kg/dm³ (≈ 1220 kg/m³. Auction-ID: A1-41983-101

Universal Components Mixer EM 300 in stainless steel, Fabr. MTI Detmold / Germany, built in 1997

used screening machine, function-tested, immediately available

The main machines in the line: fluid mixer Trusioma hot and cold KO-kneader BUSS Mixing mill Buzuluk 660x2100 mm 4-roll calender Buzuluk 700x1800 mm, inverted "L" tempering and stretching device behind the calender – roller track film thickness profile measuring device winding device

Dryer / Centrifugal Dryer / Dry Cleaner Can be used for pre-shredded plastic waste (hard plastic, films), Throughput depending on the type of material approx. 0.5-2 t/h Drive power 30 kw

Conveyor belt / belt conveyor Belt width: approx. 300 mm Axle distance: approx. 3,130 mm Drive: 0.75 kW new - only very short in use

Conveyor belt / belt conveyor Belt width: approx. 1,400 mm Axle distance: approx. 8,000 mm Drive: 2.2 kW

Condition: Very good condition

Vacuum: 20 mbar Motor Oil: Type SAE 30 Qt.: 6 Ltr.

62 m³/h 60 hPa (mbar) 1,5 kW

Hz: 50/60 V250/300 m3/h P 100 hPa (0.1 bar)

MF-0170 4-Axis Ripper - Brand: Weima - Model: ZM30 - Year: 2000 - Two motors of 11 KW each (15 hp) - Cutting chamber: 600 x 462

MF-0169 1-Shaft Ripper - Brand: Weima - With hydraulic pusher - Model: WL 500 - Power: 15 hp (11 KW) - With rotor width of 500 mm - Year: 2008

- Brand: PURIPLASTIC - Model: NG.320 - Spindle diameter: 320 mm - Spindle speed: 63 rpm - Main engine power: 180 hp (132 KW) - Cut-off: 4 HP (3 KW) - Electrical panel

USED VERTICAL MIXER, constructed in sturdy carbon steel, Nominal capacity 8.500 lt.ca, inspection hatch on barrel, loading hopper, control panel, capacity: 5.000 kg ca, conditions: used

USED VERTICAL MIXER, constructed in sturdy carbon steel, Nominal capacity 8.500 lt.ca, inspection hatch on barrel, loading hopper, control panel, capacity: 5.000 kg ca, conditions: used

AMT PostPro SFX – Chemical Vapor Smoothing System | Year of Manufacture 2024, Used vapor smoothing system for professional post-processing of 3D-printed parts, The AMT PostPro SFX brings industrial surface finishing to the lab bench. As the worlds first desktop vapor smoothing system, it processes parts from SLS, MJF, HSS, and FDM/FFF into injection-molding-like surfaces – fully automatic, odor-neutral, and without complex room installation., Technical specifications, Manufacturer: AMT (Additive Manufacturing Technologies), Model: PostPro SFX, Year of construction: 2024, Process chamber: 190 × 320 × 190 mm (approx. 11.5 liters), Footprint: 450 × 500 × 845 mm, Weight: approx. 50 kg, Cycle time: 90–120 minutes, Connection value: 230 V (Plug & Play), Compatible processes: SLS, MJF, HSS, SAF, FDM/FFF, Materials: PA12, PA11, Onyx, filled nylons, Consumables: AMT Pos ...

Year: 2011 - technically efficient, ready to work – after full service - WT 535B automatic rotary station - disc cutter: 250 mm - windows PC control - profile recognition system - for turning tools on and off as needed - extensive tool equipment

MD-0107 Overhead Cut to Water - Brand: BAUSANO - Model: TDF-500 - Year: 2015 - With 1.5 meter centrifuge - Made of stainless steel - 5.5 hp (4kw) - With water bath and electrical panel

Year: 2006 - technically efficient, ready to work – after full service - handle function - copying template - pneumatic profile mounting - centering device

GT-5407 Knife Sharpening Machine - Brand: HOLZ MANN - 1 meter - Auto-scroll - Manual lowering - Power: 2HP (1 kW)

GT-5382 Corrugator for Pipe - Brand: ITIB - 1.85 m long with chain sets of: - 21 Ø 2 mm Separ - 25 Ø 2 mm Separ - 25 Ø 3 mm Separ

GT-5322 2-Axis Ripper - Brand: JBF - Model: DC 50/40 - Cutting chamber: 500 x 400 mm - Motor: 9.2 KW - Year of manufacture: 2015 - With 2.70 x 0.35 feed conveyor

- For plastic, - Brand: Falzoni, - Model: FBP600, - Engine: 30 kW (40 hp). - Tank: 250 L. - Vacuum cleaner for steam extraction 0.5 Kw (0.75 hp). - With electrical panel.