rubber machines used for sale

Key data: 450 mm, 1200 mm

Manufacturer: Berstorff Type: 1200 x Ø 450 mm Year of manufacture: 1961 / revised by DEGUMA Engine No.: 60-20409 Rolls: 1200 mm roller length 450 mm roller diameter Cylindrical rollers, smooth roller surface Roller cooling: Central bottle neck bore, with NEW ROTOFLUX rotary unions Speed: Fixed speed, non-variable Rear roller: 18.2 rpm = 25.7 m/min Front roller: 16 rpm = 22.6 m/min Friction: 1 : 1.14 – new coupled wheels Roller bearings: plain bearings, very good condition, bearing journals reground during last revision Lubrication: Automatic oil circulation lubrication with electric pump Gap adjustment: Manual by ratchet; Display via scale on the stand Roller breakage protection: fracture plates Guide jaws: 2-part, moving material wiper jaws made of steel with center sword; Firmly attached to the bearing housings, cannot be swivelled Material pan: Sliding sheet steel ...

cross-section width:: 800 mmcross-section heigth:: 15 mmfeed:: ab ca. 5 mmspeed of feed:: m/mincuts max.:: Schnitte/mcondition: used, overhauledSpecification: Panel cutting machine - overhauled with CE- Section width max.approx.: 800 mm- Section height max.: 15 mm, depending on the hardness of the rubber sheets- Cutting length from approx.: 5 mm (depending on material)- cutting force approx.: 10 tons - Connected load approx.: 1.8 kW- Painting: green- Operating voltage: 3 x 400V, 50Hz, N, PE- Dimensions approx.: 1,200 x 1,450 x 1,950 mm - Safety devices according to current standards,- New on-board system machine,- New control cabinet with PLC system Siemens S7-1200,- CE marking,- Instructions for use and maintenance in English or German language ...

Key data: 400 mm, 1000 mm

Year of manufacture: approx. 1980 / 2024 completely overhauled by DEGUMA Machine No.: Unknown Rolls: 1000 mm roller length 400 mm roller diameter Cylindrical rollers, smooth roller surface (no fluting) - Roller bales and bearing journals reground Roller temperature control: Water cooling via central bottle neck hole, with NEW ROTOFLUX rotary unions with spray lances (Connections: 1" inlet; 11/2" drain) Speed: Infinitely variable via potentiometer Tight roller: 1 - 20 rpm = 2 - 25 m/min Adjustment roller: 1 - 16.4 rpm = 2 - 20.5 m/min Friction: 1 : 1.22 - NEW coupling wheels - Fixed friction ratio; not adjustable Roller Bearings: 4 NEW Bronze Plain Bearings - NEW silicone gaskets Lubrication: Recirculating oil lubrication with electric pump - NEW Electrical Flow Monitoring Gap adjustment: Electromotive - 2 NEW three-phase motors 1.5 kW - NEW magn ...

machine measurements: -- mmmachine weight: -- kgpower capacity: -- kWCondition: used, Specification: drum-type blast deburring machine type: MEWO Rotor TS 60- batch volume approx.: 1-600 litres,- working temperature: - 150°C- drum speed: 5 - 30 rpm- Blast wheel speed: 1,000 - 9,500 rpm- Control: Siemens S7 SimaticThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Key data: 300 mm, 750 mm

Year of manufacture: 1991 / 2023 revised by DEGUMA Make No.: 6552 Rollers: 750 mm roller width, 650 mm working width 300 mm diameter Cylindrical, smooth surface Working height: 1350 mm Note: on the roller bales there are several traces of indentation of screws Roll gap: 0.5 – 25 mm Rear roller speed: 2 – 26.5 min-1 Friction: switch for synchronization and fixed friction 1 : 1.82 Gap adjustment: electric gap adjustment Gap display: digital Material wiper jaws: 2-piece steel wiper jaws, foldable Surface temperature Roller: up to 220 °C Heating type: electric Heating capacity per roller: 18 kW Temperature control: electronic regulator with feedback Temperature sensor: RTD PT 100 Roller cooling: medium water, connection inlet Dmr. 12 mm, connection outlet Dmr. 22 mm, water pressure approx. 4 bar New rotary unions, without temperature contr ...

Press force max.:: 1600 kNheating plates:: 400 x 400 mmelectrically heated:: -- °Cheating power:: 9,92 kWpiston stroke:: 400 mmno. of stages:: 1 Condition: Used,Specification: Press 400 x 400 mm, second-hand steel frame construction- Clamping force: 160 tonnes- pressure force: 1600 kN- Operating pressure: 300 bar- Closing: from bottom to top- Heating platens: 2 electric platens- Heating power: 4.96 kW/platen- Heating platen dimensions: 400 x 400 mm- Specific pressing pressure: 1000 N/cm²- Distance between the heating platens: 500 mm- Piston stroke: 400 mm- Piston diameter: 260 mm- AC motor power: 7.5 kW- Pneumatic protective cover in the front area,- lifting device- Sliding table- Approx. dimensions: 1,760 x 1,150 mm- System height approx.: 2,470 mm- Weight appro ...

Key data: 110 mm, 350 mm

Year of Make: 1990 Make No.: 6439 Rollers: 350 mm roller width 110 mm diameter - Cylindrical, smooth surface - Height of the top of the roller to the floor: 1200 mm Roller temperature control: Electrically heated up to 300°C via electric heating rods; - Water-cooled via new spray lances and NEW rotary unions in both rollers; - Without temperature control unit Speed: Infinitely adjustable via frequency converter Adjustable roller: max. 22.5 rpm = 7.8 m/min Fixed roller: max. 27 rpm = 9.3 m/min Friction: Switchable friction ratio (friction or synchronization) - 1 : 1.2 or 1 : 1 Roller bearings: Bronze plain bearings Bearing Lubrication: Oil Circulation Lubrication Gap adjustment: Manual manual adjustment by crank - Parallel adjustment of both sides Gap Indicator: Mechanical Analog Dial Gauge Material wiper jaws: One-piece metal scrapers - Manu ...

roll diameter: 550 mmroll length: 1500 mmrolls drilled: Kernbohrung Nip adjustment: hydraulisch 0total power requirement: 90 kWThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Key data: 150 mm, 450 mm

Power supply Voltage V 380 Type of current three-phase current Frequency Hz 50 Amperage A 30 Connected load kW 18 Electrical fuse A 63 Cooling water requirement 1/min 10 Characteristics Roller diameter mm 150 Roller width mm 450 Working width mm 350 Batch volume dm³ 1 Drive Rear roller speed 1/min 20 Speed front roller 1/min 10 - 20 Friction 1 : 2 Drive torque Nm 2000 Drive power kW 8.0 Heating Surface temperature °C up to 220 Heating type: electric Heating capacity per roller kW 5.5 Total heating capacity kW 11.0 Temperature Control Electronic Controllers with recirculation Switching behavior PID Temperature Sensor Resistance Thermometer PT 100 Dimensions Machine length mm 1600 Overall length (incl. water connection) mm approx. 2000 Machine width mm 750 Machine height mm 1600 Working height mm 1200 Work surface requirements m x m ...

machine measurements: 850 x 1.800 x 1.450 mmmachine weight: 360 kgpower capacity: 0,7 kWCondition: newSpecification: Powder coating machine, type: EPC-30/2EThe machine is designed for the powder coating of cables, hosesand profiles.- Product diameter max.: 30 mm- Product speed max.: 1,500 m/min- Powder throughput min.: 30 g/min with fine dosage- Powder throughput max.: 400 g/min per powder injector- Electrostatic: available as option- Connected load: 0.7 kW- Dimensions LxHxW: 850 x 1,800 x 1,450 mm- Weight approx.: 360 kgThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Key data: 200 mm, 450 mm

Rollers: 450 mm roller width 200 mm diameter Cylindrical, smooth surface Height of the top of the roller to the floor: 1340 mm Roller temperature control: water-cooled, spray lances in both chamber-drilled rollers, Without temperature control unit Speed: Infinitely adjustable via frequency converter Adjustable roller: max. 28 / 24 rpm = 17.6 / 15.1 m/min Fixed roller: max. 34 rpm = 21.3 m/min Friction: Switchable friction (switchable by lever) 1:1.2 and 1:1.4 Roller bearings: Bronze plain bearings Bearing Lubrication: Oil Circulation Lubrication Gap adjustment: Manual manual adjustment by ratchet; Separate setting for right and left side Gap Indicator: Mechanical Analog Dial Gauges Material wiper jaws: Two-piece metal wipers; not foldable • Strippers move with the adjustable roller when adjusting the roller gap and are therefore always in ...

roll diameter: 150 mmroll length: 300 mmrolls drilled: Flaschenhals Nip adjustment: hydraulisch total power requirement: 4 kWcondition: used, overhauledSpecification: Laboratory Rolling Mill 150 x 300 mm - second-hand Motor under the rollers- Roller diameter approx.: 150 mm- roller length: 300 mm- Friction between the rollers- Rolls drilled with central chamber for water cooling- Rolls with new slewing rings, manufacturer MAIER, for water cooling,- Rollers mounted on bronze bushes with circulating oil lubrication via pump,- Gap adjustment: NEW, hydraulic and as emergency system- Hydraulic unit NEW- NUE Tilting guide plates- NEW safety cage- Safety brake for emergency stop- AC brake motor: 4 kW - 400 Volt - 50 Hz- new mixing tanks made of stainless steel for the mixture- Safety devices according to current EN 1417:3/2015- Painting: in RAL colours according to ...

Key data: 110 mm, 225 mm

Year of manufacture: 1963 / Control system renewed in 1985 Rollers: 225 mm bale width 110 mm diameter Cylindrical, smooth roller bales Temperature control: Chamber-drilled rollers, oil-tempered via rotary union and spray lances Speed: Infinitely adjustable Solid roller: 11 - 63 rpm = 3.8 - 21.8 m/min Adjustment roller: 11 - 63 rpm = 3.8 - 21.8 m/min Friction: Infinitely adjustable Bearing: Bronze Plain Bearing Lubrication: Electric oil circulation lubrication Gap adjustment: Manual with ratchets Material guide jaws: Two-piece with centre centreboard, non-folding Material tray: plastic tray below the rollers, can be pulled out by hand Motor: Two SEW three-phase brake motors with 2.2 kW each, 230/400 V, 50 Hz, 1395 rpm Transmission: Two PIV gearboxes (for speed control) in combination with two JAHNEL helical gearboxes Control: Conventional ...

cross-section width:: 100 mmcross-section heigth:: 40 mmfeed:: 2 - 999.999,9 mmCondition: new,Specification: Impact knife cutting machine CC-600/40 for hoses and profiles- contact length: 600 mm- product diameter: 40 mm- belt width: 100 mm- Tractive force: 400 N to 800 N- Drive: 2 drives upper and lower belt- Conveyor belt speed: 100 m/min- Drive feed, cutting motor: Servo drives- Cutting capacity with blade max.: 4,000 1/min- Connected load: 3.5 kW- Dimensions L/H/B: 1,900 x 1,650 x 960 mm- Weight approx.: 580 kgThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Key data: 150 mm, 400 mm

Year of manufacture: 1989 / currently revised by DEGUMA Machine No.: 1150-22-89 Rolls: 400 mm roll width / 350 mm usable roll width 150 mm diameter - Cylindrical rollers - Chrome-plated surface - Root ball condition very good - Height of the top of the roller to the floor: 1200 mm Roller temperature control: Peripherally drilled rollers - Oil-tempered via rotary unions in both rollers; - Temperature control unit is NOT included in the scope of delivery - this can also be offered as a used device on request Roller speed: Speed of the front roller variably adjustable - Infinitely adjustable via input on the control panel) - Rear roller speed depends on the set friction Front roller: 1 – 21.4 rpm = 1 – 10.7 m/min Rear roller: 1 – 21.4 rpm = 1 – 10.7 m/min Friction: Adjustable in the range of 2:1 – 1:2 by independently adjustable speed of both roll ...

cross-section width:: 100 mmcross-section heigth:: 50 mmfeed:: 10 - 999.999,9 mmspeed of feed:: 1 - 50 m/minThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Key data: 150 mm, 350 mm

Year of Make: 1973 Make No.: 1413; Com: 23243 Rollers: 350 mm roller width 150 mm diameter Cylindrical, smooth surface Height of roller top to floor: 1020 mm Roller temperature control: chamber-drilled rollers Speed: no speed control Friction: 1:1.23 Roller Bearings: Plain Bearings Bearing Lubrication: Grease Cartridges Gap adjustment: Manual manual adjustment by spindles; Gap indicator: on scale on the adjustment spindle Material wiper jaws: Two-piece, fixed with PA6 coating Material tray: below the rollers Main drive: SEW-Eurodrive 7.5 kW, 380 V, 50 Hz Gearbox: SEW spur gear, n1: 1,400 min-1, n2: 85 min-1, i: 16.47, immersion bath lubrication Safety: Emergency retaining bracket above the rollers Control: simple contactor control with brake motor El. Connection: 3 Ph., 400 V, 50 Hz Dimensions: approx. 2,000 x 1,000 x 1,700 ...

cross-section width:: 700 mmcross-section heigth:: 500 mmfeed:: -- mmCondition: used, overhauledSpecification: splitter for rubber bales - overhauled with CE- cross section width max.ca.: 700 mm- cross section height max. approx.: 500 mm- cutting force approx.: 10 tons - AC motor: 4 kW, 400 V, 50 Hz- Infeed roller conveyor for product transport- Machine stands on a raised pedestal- Two-hand safety control for driving the blade movement- Safety guard according to current standards- New control cabinet- New on-board system machine- Operating and maintenance manual in English- CE marking- Paintwork: according to customer requirements- Refurbished with 1 year warranty- CE marking,Option:- Output roller conveyor newThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Complete salt bath production line, cold feed extruder EEK 90.21 V with LCM 26 RS - Details in brief

roll diameter: 550 mmroll length: 1500 mmrolls drilled: Kernbohrung Nip adjustment: Hydraulisch total power requirement: 150 kWCondition used, refurbished, Specification Roll mill 550 x 1500 mm - used- roll diameter: 550 mm- roll length: 1500 mm- Variable friction ratio between rolls - cored rolls with central chamber for water cooling- nip adjustment: NEW hydraulical- hydraulic unit: NEW- tipper guiding plates- cylinders: mounted on bronze bushings with forced oil lubrication by pump, new rotary joints for connections to water circuit- N.2 safety brake for emergency stop - N.2 AC engine 75 kW – 380 V – 50 Hz- mill tray to contain compound- bi-directional bars for safety system- visualization display to monitor gap between rolls an ...

125 mm cold-feed siftext rudder with strainer or strand injection head for calender loading

clamping force: 1.300 kNinjection volume: 230 cm³screw diameter: 45 mmplaten size: 685 x 685 mmCondition: used,Specification: injection moulding machine for TPE - usedincluding Koch dosing unitclamping unit:- clamping force: 1.300 kN- heating platen size: 685 x 685 mm- Clear distance between tie bars: 470 x 470 mm- Mould installation height min.: 250 mm- Distance between platens max.: 900 mm- Opening stroke max.: 650 mm- Ejector stroke: 225 mmInjection unit:- Screw diameter: 45 mm x 18D- Injection volume max.: 230 cm³- Injection part weight: 210 g/hp- Max. injection pressure: 1,670 bar- Screw circumferential speed: 75 m/min- Cylinder heating: 4x 2,200 W- Nozzle heating: 600 W- Connection value: 3x 400 V, 50 Hz- Electrica ...

Cold-feed pin extruder, EEK 125.10 M, screw speed 10 to 60 rpm, drive 135 KW AC

cross-section width:: Schläuche max. 11 mmcross-section heigth:: 11 mmfeed:: 0,5 - 100.000 mmCondition: used, very good conditionSpecification: universal cutting machine with roller drive for hoses - small cutting machine for hoses- feed unit: roller drive- microcontroller control: 80537- cutting unit: pneumatic- Type of cut: Blade cut- Industrial blade: for PVC hoses- Max. hose diameter: 11 mm- Maintenance unit: yes- Max. feed speed: 1 - 50 m/min - Cutting capacity max.: 450 cuts/min depending on the cutting length- Cutting force approx.: 500 N at 6 bar- Cutting length: 0.5 - 100,000 mm- Resolution/step change: 0.5 mm- Operating voltage: 230V, 50-60 Hz- Compressed air: 5 - 6 bar- Air consumption per stroke approx.: 0. ...

Cantilever Batch-Off, strip width 2-fold, 40 to 120 mm, strip thickness 6 to 12 mm, Throughput capacity 500 to 800 kg/h

machine measurements: 1500 x 2400 x 1150 mmmachine weight: -- kgpower capacity: 12 kWThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Fine strainer system from UTH, type Roll-Ex 70 TRF

0: 200 °CTorque: - 0Dimensions (HxWxD): 680 x 1320 x 760 mmweight: 177 kgThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Powder machine PM 1000 Z , Fabr. PEKU / Germany, for powdering rubber films and sheet goods up to 1000 mm passage width,

screw ø:: 90 mmscrew length:: 20D screw speedl:: 0 - 60 U/minCondition: NEW,Specification: Rubber vacuum extruder - with warranty- Screw diameter: 90 mm- Screw length: L = 20 D (approx. 1,800 mm conveying length)- Screw speed: 0 - 60 rpm- Centre height of extruder: approx. 1,125 mm incl. base frame- Max. permissible injection pressure: 500 bar- with feed roller- Extruder water-tempered- Extruder base frame as welded construction, to accommodate the extruder with drive motor, the temperature control, the vacuum pump- Funnel piece with intermediate flange: two tempering zones approx. 4D = 480 mm- Vacuum cylinder: three tempering zones BL = 1,057 mm- End cylinder: one temperature control zone  ...