subcategories
(3rd category level)
Manufacturer:
(Category: 107)
Feed length - 0.1 - 6500 mm Width 20 - 300 mm Belt thickness 1.0 - 3.0 mm Material Quärschnitt 500 mm2 motor - 2,2 kW Complete documents more info on request
sheet width: 300 mmplate thickness: 2,5 mmdistance between columns: 300 mmdiameter of upper rolls: 32 mmtotal power requirement: Handbetrieben weight of the machine ca.: 15 Kgdimensions of the machine ca.: 500 x 300 x 150 mmSheet bending machine with:- Capacity 1050 x 2 mm- High strength wrought iron rollers with SAE 1050 certificate.- Footswitch- conical bending- Swiveling top roller- Safety device emergency leash- Documentation- 400 volts- CE certificateThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
material width: 300 mmmaterial thickness: 2,0 mm: max. 90° Gradweight: 12 Kgdimensions: 400 x 250 x 100 mCombined sheet metal working machine with:- Bending, tool widths 25 - 50 - 75 - 75 - 105 mm.- Rolls, roll diameter 38 mm- scissors, max. 1015 x 1mmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
: 30 / 900 mm: 30 / 900 mmL-beam: 35X35X5 / 600 mmT - beam - web outwards: 50x6 / 600 mmAxis diameter: 40 mmwork speed: 4,5 m/minroll diameter: 148 mmtotal power requirement: 1,1 kWweight of the machine ca.: 0,3 tdimensions of the machine ca.: 0,75 x 0,6 x 1,4 mElectric profile roller- Either horizontal or vertical working- 1 set of hardened standard rollers- lower 2 rollers are driven- 1 set of plastic rollers for diameter 33.7mm / 1 - Operation manual- Foot switch left / right and EMERGENCY STOPThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
working width: 2000 mm for sheets up to: 3 mm Clear stand width: 2050 mm Stand discharge: 250 mm Support table size: 220 x 2200 mm electr. Drive: 380 V, approx. 5 kW Weight: 2.7 t
round bar steel: 25 mmsquare edge steel: 22 mmL-beam: 70 x 7 mmcutting capacity: 100 x 10 mmplate thickness: 10 mmtotal power requirement: 1,3 kWweight of the machine ca.: 0,6 tdimensions of the machine ca.: 1,1 x 0,65 x 1,5 mThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Make: RIJVA Model: 502/1 S/N: 405 Cap: 12 tons
Ref.-No. 10017 – No. 21-1417 Described Open Laser System Manufacturer SH-Germany Type LAS 26 Year of construction New LAS 26 The LAS 26 is an open laser system with which small parts and also large, bulky parts can be lasered. Due to the lack of limitation of an enclosure, the dimensions of the workpiece are variable. It is possible to integrate this laser system into an existing system. Product • Fiber laser 20 W (optional: 30 W, 50 W) • Laser class 4 • Marking field size 150 x150 mm • Marking software EZCAD • Pilot laser (easy preview) • Focus finder (easy focus adjustment) • Marking height approx. 330 mm • Electrically adjustable Z-axis (Working Plane setting) • Connection 230 V • Air-cooled • Laptop with Win 10 • Dimensions: approx. 840 x 775 x 700 mm (L x W x H) • Weight: approx. 45 kg
Ref.-No. 10013-21-1337 Marking laser SAL 27 Name of the attachment marking laser SAL 27 Manufacturer S-Germany Model SAL 27 Year of construction of new goods The SAL 27 in a flexible allroud talent. Thanks to the three different, manually adjustable axes, inscriptions from small to very large parts up to a height of over one meter can be easily realized. With the swivel axis, the laser head can be positioned in the most difficult places. The SAL 27 is mobile and can be easily rolled onto the workpiece. Product • Fiber laser 30W (optional 50W) • Laser class 4 • Wavelength 1064nm • Marking field size standard 110 x 110mm (optional 150 x 150mm) • Y-axis from 1020 - 1320mm, travel max. component height 1120mm X-axis approx. 250mm travel • Pilot laser (easy preview) • Focus finder (easy focus adjustment) • manually adjustable Z-axis • Touch PC with la ...
Ref.-No. 10010-21-1339 Portable Laser Name of the system Compact ALL-in-one system component for laser processing Portable Marking Laser Manufacturer SH-Germany Model SAL 23 Year of construction NEW Compact ALL-in-one system component for laser processing • Fiber laser 20W (Optional: 30W, 50W) • Laser class 4 • Wavelength 1064nm • Marking field size 110x110mm • Marking software EZCAD • Electrically adjustable Z-axis (working plane adjustment) • Welded construction made of sheet steel • Connection 230V • Air-cooled • Touch IPC with Windows 10 operating system • Keyboard • Dimensions: 1150 x 500x 1500mm (DxWxH) • Weight: approx. 85 Kg • Weight of the portable laser unit 6.8 Kg • Smoke extraction included
Ref.-No. 10009-20-1276 Table Laser Designation of the attachment marking laser SAL 22 Manufacturer SH-Made in Germany Model SAL22 Year of construction NEW Compact ALL-in-One table machine for laser processing • Fiber laser 20W (Optional: 30W, 50W) • Laser class 1 • Wavelength 1064nm • Marking field size 110x110 mm • Marking software EZCAD in German / English • Pilot laser (easy preview) • Focus finder (easy focus adjustment) • max. component height approx. 300 mm • marking height approx. 110 mm • Working range approx. 390x240mm • Welded construction made of sheet steel • Connection 230V • Air-cooled • Notebook with cable, Windows 10 (German or English) • Dimensions: 670x 430x 700 mm (LxWxH) • Weight: approx. 55 Kg
Punching machine Trumpf TruMatic TC3000-1300 FMC Year of construction 2004 87500 hours (03.2021) In this case, the configuration : TruMatic TC3000-1300 FMC Year of construction 2004 Working range : 2550 x 1280 mm Standard: • Sturdy C-frame • Coordinate guidance with integrated linear magazine, 21 seats for tools and clamps • 2 clamps • Drives: Maintenance-free digital three-phase servo motors • Punching head: hydraulic system with closed control loop, hydraulic mono tool holder, 360° rotation for all Tools, automatic tool length compensation, programmable scraper movement • Programmable hold-down • Tool spray lubrication • Punch butt suction • Partial slide 500 x 500 mm • Control Bosch PNC-P, activity-oriented user interface, Online Help, Diagnostics, 3.5" Floppy Drive, RJ45 Network Connection • Graphics programming ToPs 2000 • ToP ...
Single Slab Reheat Furnace • Type: Walking Beam • Manufacturer: Davy • Capacity: 150 t/h • Inside Refractory Width: 8,35 m • Effective Length: 32,6 m • Slab Thickness: 160 mm • Slab Maximum Length: 7,5 m • Primary Fuel: mixed BFG and COG • Alternate Fuel: N°6 Fuel Oil • Commissioned in 1995 Water Descalers • Primary descaler at slab reheat furnace run out table • Front and back 3 Hi Rougher Mill descalers. • Finishing Mill descaler at run-in table. Water Descaling Pumps • Manufacturer: Union Pump Company • N° of Pumps: Two (one operating, one stand by.) • Power: 5.000 HP (3.730 kW) • Pump Speed: 4.500 rpm • Discharge Pressure: 127 barg (1.840 psig) Rougher Mill • Type: 3 Hi, one stand 22" x 34" x 100" Reversing Mill • Manufactured by Blaw-Knox in 1923. • Ma ...
Very high-quality CNC – controlled precision sheet metal bending machine with automatic bending sequence calculation – automatic, CNC – controlled double-sided pre-bending – conical bending device Roll diameter 350 mm Smallest weft diameter 1.1 x the roll diameter = 385 mm Maximum bending length 3,000 mm Nominal pre-bending performance over the entire bending length at 5 x D = 18 mm for sheet steel/ST40 Nominal bending performance over the entire bending length at 5 x D = 22 mm sheet steel/ST40 Drive power 22 kW Weight 13,500 kg. Three hydraulically driven rollers (one hydraulic motor per roller) - The rollers run in bronze plain bearings Hydraulic linear sub-roller adjustment Hard chrome-plated piston rods Hardened and ground rollers PILZ® Laser Validation BECKHOFF® CNC – Control with Ethernet technology and large touch screen DANFOSS® Precision Hydrau ...
Very high-quality CNC – controlled precision sheet metal bending machine with automatic bending sequence calculation – automatic, CNC – controlled double-sided pre-bending – conical bending device Roll diameter 350 mm Smallest weft diameter 1.1 x the roll diameter = 385 mm Maximum bending length 3,000 mm Nominal pre-bending performance over the entire bending length at 5 x D = 18 mm for sheet steel/ST40 Nominal bending performance over the entire bending length at 5 x D = 22 mm sheet steel/ST40 Drive power 22 kW Weight 13,500 kg. Three hydraulically driven rollers (one hydraulic motor per roller) - The rollers run in bronze plain bearings Hydraulic linear sub-roller adjustment Hard chrome-plated piston rods Hardened and ground rollers PILZ® Laser Validation BECKHOFF® CNC – Control with Ethernet technology and large touch screen DANFOSS® Precision Hydrau ...
Very high-quality CNC – controlled precision sheet metal bending machine with automatic bending sequence calculation – automatic, CNC – controlled double-sided pre-bending – conical bending device Roll diameter 350 mm Smallest weft diameter 1.1 x the roll diameter = 385 mm Maximum bending length 3,000 mm Nominal pre-bending performance over the entire bending length at 5 x D = 18 mm for sheet steel/ST40 Nominal bending performance over the entire bending length at 5 x D = 22 mm sheet steel/ST40 Drive power 22 kW Weight 13,500 kg. Three hydraulically driven rollers (one hydraulic motor per roller) - The rollers run in bronze plain bearings Hydraulic linear sub-roller adjustment Hard chrome-plated piston rods Hardened and ground rollers PILZ® Laser Validation BECKHOFF® CNC – Control with Ethernet technology and large touch screen DANFOSS® Precision Hydrau ...
CNC - Sheet Metal Parts - Roll Straightening Machine for plane straightening and relaxing of thermally cut sheet metal parts, for stamped parts, for sheet metal parts that have been cut to size with the sheet shear. Our roller straightening machine is a purely electric machine, not hydraulics, the electronically controlled servo motors enable automatic CNC – controlled face straightening in the continuous process. CNC – controlled precision sheet metal parts roll straightening machine for sheets from 0.7 mm to a maximum of 14 mm sheet thickness at 500 mm sheet width Largest sheet width 1,500 mm Guideline power over the full width - - Steel sheet quality SR235 from 0.7 mm to 10 mm - Stainless steel sheet from 1 mm to 6 mm Planning by - 19 piece straightening rollers with Ø 50 mm 21 pieces of intermediate rollers with Ø 30 mm 13 pieces of support roller sets wi ...
CNC - Sheet Metal Parts - Roll Straightening Machine for plane straightening and relaxing of thermally cut sheet metal parts, for stamped parts, for sheet metal parts that have been cut to size with the sheet shear. Our roller straightening machine is a purely electric machine, not hydraulics, the electronically controlled servo motors enable automatic CNC – controlled face straightening in the continuous process. CNC – controlled precision sheet metal parts roll straightening machine for sheets from 0.7 mm to a maximum of 14 mm sheet thickness at 500 mm sheet width Largest sheet width 1,500 mm Guideline power over the full width - - Steel sheet quality SR235 from 0.7 mm to 10 mm - Stainless steel sheet from 1 mm to 6 mm Planning by - 19 piece straightening rollers with Ø 50 mm 21 pieces of intermediate rollers with Ø 30 mm 13 pieces of support roller sets wi ...
sheet width: 3100 mmplate thickness: 6 mmpre-bending: 5 mmupper roll diameter: 170 mmmin. bending diameter: Ø 255 mmbending speed: 4,5 m/mintotal power requirement: 4 kWweight of the machine ca.: 2300 kgdimensions of the machine ca.: 3800x1100x1130 mmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
• 3000w IPG with Picking • Sorting Unit LSR & Combo Storage H38 • Large Format 3000 x 1500mm • Year 2014 • Servo Electric - High Speed 30 Ton Punching Head • ONLY 535 HOURS!
1250 x 2500mm TLF 2000w Laser STOPA Sheet storage, SheetMaster, ToolMaster, SortMaster Year: 2005
TOP CONDITION - OVERHAULED IN 2022 ! - 1 year warranty Year of construction: 2007 Panel format: 3000 x 1500 x 100mm Power: 4000W Control: Mazatrol Preview with LAN / USB incl. cooler incl. linear drives on all axes incl. programming software incl. training incl. commissioning incl. quick puncture incl. ball roller table incl. 4x head change magazine incl. 2 cutting heads incl. 10x automatic nozzle changer FE: up to 24mm VA: up to 15mm oxide-free designed for high-pressure cutting up to 20bar no foundation ! necessary Optional automatic loading and unloading by Mazak CELL510 can be offered with warranty / commissioning / training always regularly maintained
sheet width: 2035 mmplate thickness: 6 mmdistance between columns: 2000 mmtotal power requirement: kWweight of the machine ca.: tdimensions of the machine ca.: mmotorized limit stop behindfoot switchTechnische Daten / technical details:Schnittleistung (Blechdicke) / max. cutting capacity (thickness of sheet) 6 mmSchnittlänge / max. cutting length 2035 mmHinteranschlag / arrester behind 1000 mmStänderweite / distance between columns 2000 MmAntriebsleistung / drive capacity 11 kWGewicht der Maschine / weight 3500 kgTechnische Daten, Zubehör und Beschreibung der Maschine sind unverbindlich -Technical data, accessories and description of the machine are not binding.The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Punching machine X5 Manufacturer: FINNPOWER YEAR: 2006 Desktop... 2530x1270mm Nominal pressing force... 056 Axis X ... 2584mm Axis Y ... 1317mm thickness of the cut material ... 8mm Magazine slots ... 20 Control Fanuc ... Oi-PC Machine weight ... 10500kg L x W x H ... 7600x6980mm The machine is in good condition, possible to test under power.
sheet width: 3000 mmplate thickness: 50 mmpre-bending: total power requirement: kWweight of the machine ca.: tdimensions of the machine ca.: mThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
sheet width: 3050 mmplate thickness: 25 mmdistance between columns: mmtotal power requirement: kWweight of the machine ca.: tdimensions of the machine ca.: mThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Specifications: - max. material thickness at 40 kg/mm² strength approx. 3 mm - Shaft mount 45 mm - manual hydraulic feed of the top roller - E. foot switch - Drive 400 V / 1.1 kW - Space requirement approx. W 550 x H 1200 x D 1200 mm - Weight approx. 180 kg
Unbek. Type, YOC ca. 1990, Revision 2002 Specifications: - Bending capacity at 45 kg / mm² up to approx. Ø 25 x 3 mm - Bending angle left + right selectable - Hydr. Double-sided bending function - Hydr. Delivery ° - Drive 400 V / 11 kW - Space requirement approx. W 1750 x H 2200 x D 2300 mm - Weight approx. 1600 kg - with - bending angle adjustment - Hydr. Voltage - Bending tools
Inv. Num. : 3861 Type: L-K 120-3100 TSI Producer: SAFAN Created: 2002 Parameters: Control system: SAFAN Pressing force: 1200 KN Bending length : 3100 mm stroke: 180 mm Dimensions: 4200 x 1650 x 2775 mm Machine weight: 8700 kg
sheet width: 3100 mmplate thickness: 10 mmcutting angle: 2 °down holder: 14 Stückno. of strokes: 13 Hub/minthroat: 350 mmoil volume: 260 lcontrol: CYBELEC CybTouch 8 total power requirement: 22 kWweight of the machine ca.: 10.550 kgdimensions of the machine ca.: 4000x2250x2050 mmDomestic equipments:- Hydraulic swing cut sheet metal shears- Touch screen controller with digital display for backgauge- automatic kerf adjustment via the control- Backgauge control 1000 mm travel with recirculating ball screws- Vibration cutting machine with kerf adjustment- 2 support arms- 1 side stop- Photocell behind the machine- Cutting length limit- cut line lighting- Chrome steel knife- Ball rolls in the table- hinged finger guard with limit switch- Footswitch- CE mark / Declaration of Conformity- Bed instructions in GermanThe data for this ad was created with ModulMWS - the software solution of LogoTec ...
