subcategories
(3rd category level)
Manufacturer:
(Category: 107)
Trumpf TruBend Cell 5000Year of manuf. : 2018 Control : ____________Description:Technical dataYear of manufacture:2018Pressing force approx.:3200 kNFolding length approx.:4420 mmControl system:TASC 6000Projection:420 mmFree upright clearance approx.:3680 mmUsable installation height approx.:615 mmMachine weight approx.:23400 kgEquipment:- Sturdy machine frame:- Press beam, stress relieved with high bending strength:- Spherical bearing of the press beam (inclined position):- Electro-hydraulic top drive with 4-cylinder technology:- Optical set-up and positioning aid:- Generous edge clearance:- Flat front covers:- Block hydraulics:- Electronic pressure compensator:- Measuring system with glass scale and deflection compensation:- Hydraulic oil in the machine (lifetime lubrication):- Oil cooler:- Control cabinet cooling via air-to-air heat exchanger:- Modern machine designExtended equ ...
Messer MultiTherm 4000Year of manuf. : 2020 ____________Description:Technical specificationsWorking surface:2000 mm x 15000 mmTotal width:5070 mmHeight:1980 mmequipment:-Global Control S with 15 colour touchscreen:-Joystick and handwheel for Global Control S panel:-Cooling for the control cabinet:-Laser diode:-Drives up to a maximum of 35 m/min. AC:-Heat shield without air cooling:-Runway for double-sided longitudinal drive HEB:-OmniFlow oxyfuel supply up to 70 m/h (gas flow control):-ALFA machine cutting torch (internal ignition):-Smartlifter 300:-SensoMat ARKI:-Full addressing of gases:-Light barriers:-Safety device for wheel housing (foot switch)
: neu : ca. 2 - 4 Wochen ab Auftr : Niederlande : 853 €: 20 - 76,1 mm: 3 mm: 2.5 mm: 7 kgThe ALU can be used to notch a sink outflow in pipes with an external diameter of 22 mm to 76 mm.Since ALMI pipe notchers have a favourable price and high productivity they are an excellent investment.ALMI pipe notchers are available for cutting out venting slots in round and rectangular met pipes with an external diameter from 27 mm upwards and a wall thickness of a maximum of 3 mm.All the benefits in a nutshell: high productivity, low investments, simple and rapid operation, a number of diameters are immediately available.The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
: gebraucht : 2023 : 9676 : prompt, Zwischenverkauf v : Deutschland : 13700 €: 1 : 1250 mm: 1.25 mm: 1,25 mm bei 1 Messerpaar, : 0.37 kW: 36 m/min: 70 mm: 1900 mm: 1600 mm: 1000 mm: 350 kgdemo machine / mint condition - fixprice3 pairs of bladesLength measuring by wheelDigital preselection of one positionBrake motorRubber feeding rollsManual crosscutting equipment in front and behind blade shaftwith 1 cutting slide which alternaingly can be used on front and backsideUser manual in GERMANOPTIONS:Additional pair of bladesDecoilerThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
: neu : ca. 2 - 4 Wochen ab Auftr : Niederlande : 4955 €: 3/4 26,9 mm, 1 33,7 mm, mm: 5 mm: 3 mm: 87 kgThe motor driven AL 1-2E can be used to notch pipes with an external diameter of 26.9 mm (3/4",), 33.7 mm (1",), 42.4 mm (1 1/4",), 48.3 mm (1 1/2",) and 60.3 mm (2",).Do you often have to notch pipes? If so, the motor-driven AL1-2E equipped with a 2.2 kW electric motor is the ideal solution!The motor forms one unit with the special eccentric shaft that drives the notching tool. The motor is also equipped with an on/off switch with a zero voltage protection and guard.All the benefits in a nutshell: high productivity, low investments, simple and rapid operation, a number of diameters are readily available, ideal for double corner joints.The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
: neu : ca. 12 Wochen ab Auftrags : Türkei : Wechseltisch Laser sources from 3 - 30 kWTable dimensions:3 x 1,5 / 4 x 2 / 6 x 2 / 6 x 2,5 mThe shuttle table is positioned longitudinally, which results in the best possible accessibility for optional loading and unloading systems.The system consists of the following components:Shuttle table system in longitudinal direction for simultaneous loading/unloading and cutting to reduce non-productive production timesEncapsulated cutting room with protective glazingCNC graphics control Siemens Sinumerik 840DLaser source Brilase or IPGCutting head with automatic focus adjustment, Durma or PrecitecCooling unit for cutting head and laser sourceCAD/CAM software LANTEK for programming including autonestingPositioning laserSheet check system (automatic detection of sheet position and dimensions)Automatic nozzle cleaningCentral lubricationSlug boxWorking ...
: neu : ca. 6 Monate ab Auftragse : Spanien STANDARD EQUIPMENT• Uncoiler• Coil car• Pneumatic input table• Entry guide• 7 Straightening rolls• Slitting shaft with 3 sets of quickly adjustable circular blades• Cut-to-length shears• ServomotorOPTIONS• Hydraulic input table• Film plastic device• Scrap rewinders• Additional circular blades• Stacking tables• Packers Model: Width to process: Cutting thickness (mm): Coil weight (kg) Number of straightening rolls: Cutting accuracy: Number of straightening rolls: Production speed: TwinCut 20 DM6 100012501500 0`5 - 2 6.000 3 - 6+/? 0`5 mm 2 + 7 20 m/min TwinCut 20 DM10 10.000 TwinCut 20 DM15 15.000 MATERIAL TO BE PROCESSED: THICKNESS: N OF SIMULTANEOUS CUTS: Steel 420 Nw/mm2 2`00 mm 3 1`50 mm 4 0`50 mm 6 Steel 700 Nw/mm2 1`25 mm 3 1`00 mm 4 0`50 mm 6 Steel 200 Nw/mm2 4`00 mm 3 2`00 mm 5 1`00 mm 6IF YOU ARE INTERESTED, P ...
: neu : 2026 : 090202 : Mai 2026, Zwischenverkauf : Türkei : 3100 €: 1.2 mm: 100 mm: 140 nm: 8 Stk.: 62 mm: 0.75 kW: 32 1/min: 900 mm: 450 mm: 1350 mm: 135 kgHaevy duty cast iron main frameBrake motorFoot pedalAdjustable lower roll8 set of rollsComplete with standUser manual in ENGLISH or GERMANThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
: neu : ca. 8 Wochen ab Auftragse : Türkei : 29990 €: 572.81 €: 0.4 - 3.5 mm: 200 mm: 700 mm²: 80 mm: 75 m/min: 10 m/s²: 10 Nmhelical gear boxWATTDRIVE (Made in Austria)FESTO pneumatic equipmentservo drive and control SIEMENS7", colour touchscreen SIEMENS2 driven rollsOPTIONAL EQUIPMENTHandrwheel and Simlinx remote control € 4.290,--The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
: neu : ca. 12 Wochen ab Auftrags : Italien : 57900 €: 1094.31 €: 1 : 650 mm: 0,5 - 170 mm: 670 x 2200 mm: 4000 m³/h: 120 mm: 6 bar: 78 (+/-2) dB: 22 kW: 2600 mm: 1350 mm: 2100 mm: 1125 kgWITH 2 WORKING STATIONS: 1 X GRINDING BELT UND 1 X BRUSH UNIT ON TOPMachine made of stress-free welded steel construction for stable and rigid structure.Work table with motorised height adjustment via 4 synchronised spindles.Independent drive motors for each work group.Hoods for extraction inside the machine, one per station.Touch screen for-Automatic star-delta connection of the main motors- Analogue ammeter for each group- Digital display for sheet thickness with decimal point tolerance- Material thickness adjustment (+/- 0.1 mm)- Machine condition monitoring with alarm messagesFEEDING SYSTEMRobust steel structure, wear-resistant surface.Vacuum conveyor belt on requestVariable feed speed via freq ...
: neu : ca. 12 - 14 Wochen ab Auf : Deutschland : 1 : 4010 mm: 1.25 mm: 2 mm: 1.25 mm: 4 : 4 : 1130 mm: 180 mm: 915 mm: 2.2 kW: 5200 mm: 1435 mm: 1980 mm: 2600 kg: 145 °hydraulic drivestandard controladditional rail on the bending beam2x foot pedalremoveable material supportsafety equipment accoring to the control rules BG GermanyOPTIONS AS ROTARY SHEAR, CNC CONTROL, BACKGAUGES … ON REQUEST Prices ex works Germany.Transport and commissioningat customers place on request.The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
: gebraucht : 1988 : 070008 : prompt, Zwischenverkauf v : Deutschland : 1200 €: 1 : 400 mm: 700 mm: 1500 mm: 2050 mm: 820 mm: 1000 mmwith brakeThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
: neu : 2024 : 9739 : prompt, Zwischenverkauf v : Türkei : 22300 €: 428.16 €: 1 : 1 : 2030 mm: 6 mm: 6 mm: 5 mm: 170 mm: 4 kW: 3600 mm: 1020 mm: 1120 mm: 2400 kg3 rollsAsymmetrical rolls arrangement - with pre-bending2 driven rollsMotorized adjustment of lateral and clamping rollDigital read-out for lateral and clamping rollSwiveling top roll to the frontForward/reverse runHardened rollsMoveable control panelUser manual in GERMAN and ENGLISH(sample photo)The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
: neu : ca. 12 Wochen ab Auftrags : Türkei : 33000 €: 630.3 €: 2530 mm: 6 mm: 6 mm: 4 mm: 190 mm: 5.5 kW: 4250 mm: 1200 mm: 1150 mm: 3750 kg3 rollsAsymmetrical rolls arrangement - with pre-bending2 driven rollsMotorized adjustment of lateral and clamping rollDigital read-out for lateral and clamping rollSwiveling top roll to the frontForward/reverse runHardened rollsMoveable control panelUser manual in GERMAN and ENGLISH(sample photo)The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
: neu : ca. 10 Wochen ab Auftrags : Türkei : 4900 €: 109.71 €: 1050 mm: 3 mm: 2 mm: 90 mm: 2080 mm: 700 mm: 1250 mm: 410 kg3 rollsasymmetric rolls - prebending2 rolls driven by handwheellateral roll adjustable by handwheellongitudinal grooves in lower and lateral rolltiltable upper rollconical rolling deviceuser manual in GERMANThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
material width:250 mmmaterial thickness:0,5 - 4,0 mmno. of straightening rolls:9 straightening roll diameter:60 mmnumber of draw-in rolls:2 power requirement:3,8 kWWeight:0,8 tDimensions (WxDxH):1,6 x 0,8 x 1,5 m
band width:1050 mmplate thickness:8 mmnumber of rolls:8 DECOILER:. - design : single coil :. - sheet width max:1050 mm - sheet width (min):150 mm - max. weight of coil:22 to - max. diameter of coil:2000 mm - min. internal diameter of coil:570 mmFEEDERS:. - feeder: type : roll feeder :. - sheet width max:1050 mm - sheet thickness max:150 mmLEVELER UNIT:. - sheet width max:1050 mm - sheet width (min):150 mm - sheet thickness max:8 mm - sheet thickness (min):2.5 mm - number of leveler rolls:8 - diameter of leveler rolls:96 mm - distance between leveler rolls:104 mm - diameter of feed rolls:160 mm - feed velocity min.:2 m/min - feed velocity max.:43.5 m/minELECTRICAL SPECIFICATIONS:. - mains voltage:400 V - mains frequency:50 HzTechnical description :Sheet metal unrolling and straightening system for thick sheet metal up to 8 mm, consisting of:- LAWECO COIL LO ...
material width:500 mmcoil weight:3,0 tmaterial thickness:0,2 - 2,5 mmcoil internal diameter:470 - 530 mmcoil external diameter:1400 mmno. of straightening rolls:9 straightening roll diameter:40 mmnumber of inlet and outlet rolls:4 material cross-cut:1200 mm²speed:1,5 - 30 m/mindimensions decoiler (WxDxH):1,9 x 0,6 x 1,7 mweight decoiler:1,1 tdimensions straightener (WxDxH):3,3 x 1,3 x 2,7 mweight straightener:3,0 tstraightening machine:RYD 40 x 500 decoiler:DY 500 x 3000 coil lifting device:hydraulic rool feed:elektronic; AESL 500-2,8 threading device:hydraulic expansion:hydraulic
material width:600 mmmaterial thickness: - 4,0 mmno. of straightening rolls:21 straightening roll diameter:30 mmmaterial cross-cut:1800 mm²speed:6 - 36 m/minPower capacity:4,5 kWWeight:2,0 tDimensions (WxDxH):1,5 x 2,0 x 1,9 m
material width:70 mmmaterial thickness:0 - 1,5 mmfeed length:100 mmmaterial cross-cut:60 mm²feeding force:400 Nclamping force of feeding pincer:1300 Nair pressure - required:3 - 6 barWeight:0,01 tDimensions (WxDxH):0,4 x 0,4 x 0,7 m
sheet width:5040 mmplate thickness:2 mmtotal power requirement:12 kWweight of the machine ca.:9,4 tdimensions of the machine ca.:6200× 1300 ×1900 mmworking width:5000 mmcontrol:Fasti Matik stroke of upper beam:500 mmadjustment of lower beam:u.Biegewange 80 mmcontrol cabinet:1000 x 850 x1450 mmDocuments:vorhanden
band width:2000 mmplate thickness:1.8 mmnumber of rolls:13 Controls:SIEMENS DECOILER:. - design : single coil :. - sheet width max:2000 mm - sheet width (min):400 mm - max. weight of coil:30 to - max. diameter of coil:2000 mm - min. internal diameter of coil:610 mmFEEDERS:. - sheet width max:2000 mm - sheet thickness max:2 mm - feeding step max.:4000 mmLEVELER UNIT:. - sheet width max:2000 mm - sheet width (min):400 mm - sheet thickness max:1.8 mm - sheet thickness (min):0.6 mm - number of leveler rolls:13 - diameter of leveler rolls:50 mm
Deburring and fine grinding machine for sheet metal / flat material, newThe compact machining centre for deburring, slag removal, rust removal, oxide layer removal, edge rounding, fine grinding through to polishing metal surfaces.Working height: variable from 0,5mm ? 150mm adjustableWorking width: 1150 mmMaximum part weight: 300 kgWide belts with abrasive belt unwinding: 2200 mmAs standard with vacuum hold system, optional with magnetic hold systemDue to the modular design of the machines, it is possible to offer the optimal configuration for the customer's machining task.The machine structure can accommodate up to 3 internal machining units and an additional external machining unit.Please, contact us for getting more information and pictures on mail(at)tar-mc.com or www.tar-mc.com
serial number: 4412956673057 : 95 to. ca. engine output: 7,5 kWweight of the machine ca.: ca 5 tdimensions of the machine ca.: 2,2 × 1,0 × 2,3 m Technical specifications (from the label)Angle steel (L-profile):150 × 15 mm at 90°100 × 14 mm at 45°Flat steel:up to approx. 150 × 16 mmlarger cross-sections up to 340 × 16 mm (depending on function)Beam profiles:U-profiles (UPN): 220I-sections (IPN)The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Deburring and fine grinding machine for sheet metal / flat material, newThe compact machining centre for deburring, slag removal, rust removal, oxide layer removal, edge rounding, fine grinding through to polishing metal surfaces.Due to the fixed working height, this machine can also be optimally integrated into a production line and is suitable for machining large parts.Working width: 1350 mmMaximum part weight: 400 kgWide belts with abrasive belt unwinding: 2620 mmAs standard with vacuum hold system, optional with magnetic hold systemBy using 2620 mm long abrasive belts, you get a uniformly smooth surface and reduce consumption costs, as these belts have a longer service life.Due to the modular design of the machines, it is possible to offer the optimal configuration for the customer's machining task.The machine structure can accommodate up to 3 internal machining units and an addition ...
Deburring and fine grinding machine for sheet metal / flat material, newThe compact machining centre for deburring, slag removal, rust removal, oxide layer removal, edge rounding, fine grinding through to polishing metal surfaces.Due to the fixed working height, this machine can also be optimally integrated into a production line and is suitable for machining large parts.Working width: 1150 - 1350 mmMaximum part weight: 500 kgWide belts with abrasive belt unwinding: 2620 mmAs standard with vacuum hold system, optional with magnetic hold systemBy using 2620 mm long abrasive belts, you get a uniformly smooth surface and reduce consumption costs, as these belts have a longer service life.Due to the modular design of the machines, it is possible to offer the optimal configuration for the customer's machining task.The machine structure can accommodate up to 5 internal machining units and 2 ad ...
Deburring and fine grinding machine for sheet metal / flat material, newThe compact machining centre for deburring, slag removal, rust removal, oxide layer removal, edge rounding, fine grinding through to polishing metal surfaces.Machine is suitable for heavy-duty use.Due to the fixed working height, this machine can also be optimally integrated into a production line and is suitable for machining large parts.Working width: 650 - 1650 mmMaximum part weight: 2000 kgWide belts with abrasive belt unwinding: 3250 mmAs standard with vacuum hold system, optional with magnetic hold systemBy using 3250 mm long abrasive belts, you get a uniformly smooth surface and reduce consumption costs, as these belts have a longer service life.Due to the modular design of the machines, it is possible to offer the optimal configuration for the customer's machining task.The machine structure can accommodate up ...
: neu : ca. 12 - 14 Wochen ab Auf : Türkei : 95000 €: 1795.5 €: 3100 mm: 13 mm: 12 mm: 8 mm: 13 mm: 10 mm: 10 mm: 8 mm: 270 mm: 270 mm: 230 mm: 50 mm: 1155 mm: 15 kW: 5310 mm: 1660 mm: 1590 mm: 10050 kg4 rollsfully hydraulic drive of upper and lower roll (from 30 mm bending capacity all four rolls) by planetary gear boxhydr. side rolls positioning with electronical synchronisationhydr. lower roll feed with mechanical synchronisationadjustable pinching pressurevariable rolling speedhardened rollsconical bending devicehydraulic drop-end bearingmoveable control paneloverload protectionuser manual in GERMAN or ENGLISHaccording to CE rulesOPTIONAL:NC controlupper and lateral supportsIMPORTANT ISSUES AT CONICAL BENDING:the max. sheet metal thickness isequivalent to 50 % of nominal capacityThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
: neu : ca. 6-8 Wochen ab Auftrag : Türkei : 12900 €: 247.68 €: 40 to: 285 mm: 200x24 mm: 660x1250 mm: 250 mm: 80 mm: 10 mm/s: 10 mm/s: 4 kW: 930 mm: 1250 mm: 650 mm: 1250 mm: 1100 kgStroke adjustment with digital displayManual and automatic operation modeTool holder pins and tools hardened and groundBending toolFoot pedalOPTIONS:Cutting-, punching- or pipe bending tools on requestThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
: neu : ca. 6 Monate ab Auftragse : Taiwan : 47400 €: 905.34 €: 2540 mm: 4.5 mm: Hydraulisch : 135 °: 3900 mm: 1700 mm: 1900 mm: 5100 kghydraulic drivenNC control for bending anglemanual back gauge 600 mmsharp rail 45° (in one piece)front angle beam 75 mmmechanical stop adjustment of upper beamclamping force adjustment of upper beamaccording to CE rulesALTERNATIVELY:versionAMH-K,withSECTIONEDsharp rail 45° OPTION:2 axes NC control with 7", touchscreen incl. motorized back gauge 800 mm (sample photos)The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
