subcategories
(3rd category level)
Manufacturer:
(Category: 107)
: neu : ca. 12 Wochen ab Auftrags : Türkei : 16100 €: 309.12 €: 2050 mm: 3 mm: 35 1/min: 1.5 °: 750 mm: 3 kW: 800 mm: 520 mm: 2720 mm: 1575 mm: 1230 mm: 1900 kgThe machines feature a robust, welded steel frame for maximum cutting precisionMotorized back gauge 750 mm, ball screw spindles, NC control2 cutting edges on the upper blade and 2 cutting edges on the lower blade800 mm squaring arm with scale2 support armsMechanical downholderManual cutting gap adjustment on the frontCutting line illuminationFoot pedalEmergency stop buttonOperating manual with EC declaration of conformity.INCLUDES THE FOLLOWING OPTIONAL EQUIPMENT:Blades suitable for cutting stainless steelRear light barrier protectionThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
: neu : ca. 4 Monate ab Auftragse : 1280 mm: 12 mm: 9 mm: 9 1/min: 3 °: 7 : 500 mm: 15 kW: 180 l: 950 mm: 1950 mm: 1200 mm: 1800 mm: 3200 kghydr. drive unit, completely integrated in the machine bodyoverload safety, hydraulic and electricaladjusting of the cutting angleadjusting of the cutting gapblank holder pressure, adjustablesupport arm with angle stop and scale up to 600 mm4 rotating knives for VA steelmovable pedal switch with solenoid valvesMotorised backgaugeCentral lubricationexchangeable machine table supportsection area lightingThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
new
: neu : ca. 12 Wochen ab Auftrags : Türkei : 35400 €: 676.14 €: 3030 mm: 6 mm: 6 mm: 4 mm: 220 mm: 5.5 kW: 4750 mm: 1200 mm: 1150 mm: 4920 kg3 rollsAsymmetrical rolls arrangement - with pre-bending2 driven rollsMotorized adjustment of lateral and clamping rollDigital read-out for lateral and clamping rollSwiveling top roll to the frontForward/reverse runHardened rollsMoveable control panelUser manual in GERMAN and ENGLISH(sample photo)The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
: neu : 2024 : 9738 : prompt, Zwischenverkauf v : Türkei : 20300 €: 389.76 €: 1 : 1530 mm: 6 mm: 6 mm: 4 mm: 150 mm: 4 kW: 3100 mm: 1120 mm: 1020 mm: 2100 kg3 rollsAsymmetrical rolls arrangement - with pre-bending2 driven rollsMotorized adjustment of lateral and clamping rollDigital read-out for lateral and clamping rollSwiveling top roll to the frontForward/reverse runHardened rollsMoveable control panelUser manual in GERMAN and ENGLISH(sample photo)The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
: neu : ca. 4 Wochen ab Auftragse : Italien : 3620 €: 38 mm: 245 mm: 300 mm: 320 mm: 23 kg: 19 cm³: 38 x 1,5 mm: 38 x 1,5 mm: 35 x 3 mm: 30 x 2 mm: 35 x 1,5 mm: 42 x 1,5 mm: 42 x 1,5 mm: 50 x 2 mm: 50 x 2 mm: 50 x 4 mm: 20 mm: 10 x 25 mm: 25 x 20 (stehend), 25 x 1 mm: 180 mm: 36 mm: 10 mm: 2,8 U/min: 0.9 kWdigital adjustment of the bending angle from 0 - 180 °single phase motor 220V / 900Welectric engine brakeindicator light for indicating overloadbasement made of cast iron, suitable for mounting a tripod (tripod not included)90° bend in 6 secondsfoot pedalwithout toolsOPTIONAL EQUIPMENT:tripod € 330,-The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
: gebraucht : WA0181 : prompt, Zwischenverkauf v : 1800 €: 1 : 3100 mm: 160 mm: 45 mmmint condition86° Slightly cranked, planedThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
: neu : ca. 10 Wochen ab Auftrags : Türkei : 103100 €: 1948.59 €: 2550 mm: 25 mm: 25 mm: 20 mm: 20 mm: 16 mm: 350 mm: 350 mm: 260 mm: 1,5-5 m/min: 22 kW: 5500 mm: 2000 mm: 1900 mm: 13000 kg4 rollsfullhydraulic drive of upper roll and lower rollhydraulic infeed of lower and side rolldigital read-out of lower and side rolls positionhardened rollsconical bending devicehydraulic load relieving of upper rollhydraulic drop-end bearing2 working speedscentral lubrication systemprotectionagainst overloadmoveable control paneaccording to CE rulesOPTIONAL EQUIPMENT:infinitely adustable speed of rollshydraulic side supporthydraulic top supportNC controlIMPORTANT ISSUES AT CONICAL BENDING:the max. sheet metal thickness isequivalent to 50 % of nominal capacitythe cone length can be max. 30 % oremust be more than 60 % of roll lengthhardened rolls are recommendedThe data for this ad was created wit ...
: neu : ca. 12 - 14 Wochen ab Auf : Deutschland : 8200 mm: 2 mm: 2 mm: 1.5 - 2 mm: 8 : 8 : 1000 mmfully automatic bending in two ways without the need to rotate the sheethydraulic driveBMS MULTI-Touch with automatic depth stoppowered rotary shearadditional rail on the bending beammaterial support2x foot pedalsafety equipment accoring to the control rules BG Germany3 year warranty on stands and tension arms.Quality Made in Germany.FURTHER MODELS FROM3 UP TO12 M LENGTH AND FROM 1,25 MM UP TO 2,00 MM BENDING CAPACITY ON REQUEST.OPTIONS: Preserving material support made out of synthetics price on request Hydraulic radius adjustment (air gap adjustment)the bending capacitiy of aluminium rises up to 2,5mm price on request Extended depth 20 - 1.250 mm price on request Conical depth stop to bend conical profiles andnarrow/wide bendings for easy intermateing price on request Fully automatic grip ...
: neu : ca. 12 Wochen ab Auftrags : Türkei : 28450 €: 543.4 €: 1550 mm: 7 mm: 7 mm: 4.5 mm: 4.5 mm: 3.5 mm: 150 mm: 150 mm: 130 mm: 1,5 / 6 m/min: 4 kW: 3750 mm: 960 mm: 1100 mm: 2500 kg4 rollsTop rolll driven by hydromotor and planetary gearbox, bottom roll driven by gear and cardan systemPinch roll and latereal rolls move with hydraulic cylindersDigital read-out for lower and side rolls positionHardened rollsConical bending deviceHydraulic load relieving of upper rollHydraulic drop-end bearing2 working speedsProtectionagainst overloadMoveable control paneAccording to CE rulesOPTIONAL EQUIPMENT:(time of deliver with options approx. 10 weeks)Infinitely adustable speed of rollsHydraulic side supportHydraulic top supportNC controlIMPORTANT ISSUES AT CONICAL BENDING:The max. sheet metal thickness isequivalent to 50 % of nominal capacityThe cone length can be max. 30 % oremust be more t ...
: neu : ca. 10 Wochen ab Auftrags : Türkei : 5200 €: 100.36 €: 1270 mm: 1.5 mm: 75 mm: 1.5 kW: 1830 mm: 700 mm: 1160 mm: 400 kg3 rollsasymmetric rolls - prebending2 rolls driven by brakemotorlateral roll adjustable by ratchet leverlongitudinal grooves in lower and lateral rolltiltable upper rollright / left rotation with double foot switchuser manual in GERMAN or ENGLISHOPTION (PRICE ON REQUEST):hardened rollsThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
: gebraucht : 2012 : 9403 : prompt, Zwischenverkauf v : China : 180 €: 1 : 1/4, 3/8, 1/2 mm: 4 kgoperation by hand lever and eccentric3 tube diameter combined in oneassembling and welding of tubesin 90 degrees angleThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
: neu : ca. 12 Wochen ab Auftrags : Türkei : 12150 €: 233.28 €: 0.4 - 2 mm: 100 mm: 200 mm²: 63 mm: 150 m/min: 10 m/s²FESTO pneumatic systemSIEMENS servo drive and control system7’ colour touch screen SIEMENS2 feed rollersOption:Handwheel and Simlinx remote maintenance module € 4.290,--The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
: neu : ca. 4 Monate ab Auftragse : 1030 mm: 10 mm: 6 mm: 10 1/min: 3 °: 7 : 5000 mm: 11 kW: 100 l: 900 mm: 1550 mm: 1150 mm: 1600 mm: 1900 kghydr. drive unit, completely integrated in the machine bodyoverload safety, hydraulic and electricaladjusting of the cutting angleadjusting of the cutting gapblank holder pressure, adjustablesupport arm with angle stop and scale up to 600 mm4 rotating knives for VA steelmovable pedal switch with solenoid valvesMotorised backgaugeCentral lubricationexchangeable machine table supportsection area lightingThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Max. working pressure 300 bar, max. stroke 180 mm Auction-ID: A1-48478-3
Tube cutting machine manufactured in 2015. This TRUMPF TruLaser Tube 5000 features a working range of 6500 mm in the X-axis and 310 mm in the Y-axis, with a maximum workpiece length of 3000 mm. It supports various tube diameters and has a maximum workpiece weight of 130 kg. If you are looking to get high-quality tube cutting capabilities, consider the TRUMPF TruLaser Tube 5000 machine we have for sale. Contact us for further details.
Manual beveling line for round tubes and bars 4-spindle deburring and chamfering machine For interior and exterior taping/chamfering Spindle speeds 70/140 rpm Material: steel, stainless steel, aluminium, non-ferrous Diameter: Ø 2 – 75 mm Min. workpiece length from 100 mm Deburring time: 3–4 sec. / front side The machine is equipped with deburring tools from the manufacturer Kopal. Tool holder is MK3 The deburring tools are adjustable so that the same chamfer depth is always achieved. Very good condition
: neu : ca. 10 Wochen ab Auftrags : Türkei : 43550 €: 831.81 €: 1550 mm: 12 mm: 12 mm: 10 mm: 10 mm: 8 mm: 220 mm: 200 mm: 160 mm: 1,5 / 6 m/min: 5.5 kW: 3900 mm: 1150 mm: 1250 mm: 3600 kg4 rollsTop rolll driven by hydromotor and planetary gearbox, bottom roll driven by gear and cardan systemPinch roll and latereal rolls move with hydraulic cylindersDigital read-out for lower and side rolls positionHardened rollsConical bending deviceHydraulic load relieving of upper rollHydraulic drop-end bearing2 working speedsProtectionagainst overloadMoveable control paneAccording to CE rulesOPTIONAL EQUIPMENT:Infinitely adustable speed of rollsHydraulic side supportHydraulic top supportNC controlIMPORTANT ISSUES AT CONICAL BENDING:The max. sheet metal thickness isequivalent to 50 % of nominal capacityThe cone length can be max. 30 % oremust be more than 60 % of roll lengthHardened rolls are rec ...
sheet width: 2000 mmplate thickness: 3,5 mmdistance between columns: 2050 mmdaylight opening: 355 mmtotal power requirement: kWweight of the machine ca.: 2,8 tdimensions of the machine ca.: 3,5 x 1,5 x 1,5 mBending machine- Bending angle preselection via limit switchesThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
I - beam section - flat steel: 100 x 15 (d 400) mmI-beam section - upend: 60 x 10 (d 500) mmL-beam: 50x50x6,0 (d 600) mmround material: 35.0 (d 500) mmbar material dia. max.: 70 x 1.5 (d 1500) mmsquare material: 50x50x3.0 (d 1400) mmbending speed: 8.5 U/minroll diam. toproll: 152 / 162 mmbore: 40.0 mmvoltage: 400 Vtotal power requirement: 2.2 kWStroke length: 120 mmweight: 470 kgrange L-W-H: 900 x 600 x 1100 mm Original price with accessories: approx. 10,000 eurosFeatures:- Two driven rollers (lower rollers)- Manual feed of the upper roller- Horizontal and vertical working positions- Shafts mounted with tapered roller bearings- Lateral, manually adjustable stop rollers- 1 set of standard rollersâsplit - 3 sets of tube rollers- 1 freely movable control unit- Operating instructionsThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
I - beam section - flat steel: 80 x 15 (Ø350) mmI-beam section - upend: 50 x 10 (Ø400) mmL-beam: 40x40x5 (Ø400) mmtool adaptor: Ø 30 Welle mmturning speeds: 7.0 U/mintube diameter: rund 60x1.5 (Ø1000) mmtube diameter: vierk 40x2.9 (Ø1000) mmtotal power requirement: 0.75 kWweight of the machine ca.: 160 kgdimensions of the machine ca.: 650 x 600 x 1400 mmFeatures:- Electric-motor-driven ring profile bending machine- Two driven rollers (lower rollers)- Manual adjustment of the upper roller- Includes analog position indicator (mm scale)- Shafts mounted with tapered roller bearings- 2 side guide rollers - Machine base frame- 1 freely movable control unit Rollers can run clockwise or counterclockwise- Various rollers included in the scope of deliveryThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
I - beam section - flat steel: 120 x 20 (d 750) mmI-beam section - upend: 60 x 10 (d 800) mmL-beam: 50 x 5 (d 1200) mmbar material - diameter: 35.0 (d 800) mmbar material dia. max.: 70 x 3.0 (d 1200) mm: 50.0 mmdiameter of upper rolls: 155 mmdiameter of lower rolls: 155 mmStroke length: 150 mmRotating speeds: 9.0 U/mintotal power requirement: 1.3 kWweight: 305 kgrange L-W-H: 900 x 700 x 1500 mmFeatures:- Robust electric-motor-driven ring/profile bending machine- Machine base frame with rear shelf- Capable of horizontal and vertical operation- Segmented standard rollers (split)- 2 sets of tube rollers, 50 + 60 mm- Manual adjustment of the upper roller- Analog position indicator for the upper rollers (scale)- Manually adjustable side/alignment rollers- Base frame with forklift pockets for easy transportThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
: gebraucht : WA0147 : 890 €: 1 : 3050 mm: 105 mm: 85 mm(screwed 5x from above)The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
: neu : ca. 8 Wochen ab Auftragse : Spanien : 11500 €: 220.8 €: 1 : 55 to: 500 mm: 40 x 10 mm: 37 1/min: 5 kW: 1550 mm: 1200 mm: 1950 mm: 1150 kghydraulic drivetable with gaugeuser manual in GERMAN and ENGLISHCNC options on requestWe have a big stock of punches and dies for immediate dispatchWE HAVE MORE THAN 700 REFERENCES!The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
: neu : ca. 2 - 4 Wochen ab Auftr : Niederlande : 979 €: 1 1/2 48,3 mm, 2 60,3 m mm: 3 mm: 2.5 mm: 15 kgThe AL 2 can be used to notch pipes with an external diameter of 48.3 mm (1 1/2",) and 60.3 mm (2",).ALMI products are subjected to stringent quality control inspections before they leave the factory.ALMI’s pipe notcher, in contrast to punch-cutting machines with separate auxiliary tools, is always available for immediate use.Moreover, the price is more affordable than the auxiliary tools for punch-cutting machines.All the benefits in a nutshell: high productivity, low investments, simple and rapid operation, a number of diameters are available immediately, ideal for double corner joints.The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
: neu : ca. 14 - 16 Wochen ab Auf : Türkei : 81500 €: 1540.35 €: 8 mm: 5 mm: 80 mm: 10 mm: 4500 mm: 720 mm: 95 (R 80) / 35 (R 25) mm: 11 kW: 4900 mm: 1700 mm: 2700 mm: 4550 kgincl. flanging rolls for mild steel (R25)incl. cutting bladetop and lower roll driven by hydromotor and plantary gear boxpossible to flange both, flat and crowned bottomshydraulically adjustable bottom heightcutting and flanging on the same headlateral support rollsoperator panel with touch screenOptional devices as fix or variable angle japanese hat attachement, rolls for stainless steel or high speed, small diameter attachement... on requestThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
: neu : ca. 6 Monate ab Auftragse : Spanien STANDARD EQUIPMENT• Entry guide• 2 Feeding rolls• 5 Straightening rolls• Cut-to-length shears• Encoder• Touch screen control• Servomotor• Slitting shaft with 2 sets of quickly adjustable circular blades, to a maximum of 6 bladesOPTIONS- Film plastic device- Different types of uncoilers- Stacking systems- Recoiler Maximum Width: Material to be processed: Thickness: Number of simultaneous slitting cuts: Production speed: Coil loading capacity: Number of straightening rolls: Straightening ServoMotor: Shears Power: Dimensions: 1250 Steel 420 Nw/mm2 1`25 mm 2 from 0 zu 120 Meter pro Minute3, 6, 10 to 2 + 5 15 kW 3 kW 2100 x 1700 x 1450 mm2500 kg 1`00 mm 4 0`50 mm 6 Steel 700 Nw/mm2 0`75 mm 2 0`50 mm 4 Aluminium 200 Nw/mm2 2`50 mm 2 1`50 mm 1`00 mm 6If you are interested, please send us your enquiry with the following details:- Coil w ...
: neu : ca. 8 Wochen ab Auftragse : Spanien : 25700 €: 490.87 €: 80 to: 500 mm: 5 : 40/14 bzw. 24/24 mm: 70 mm: 40 1/min: 450x15 / 300x20 mm: 130x130x13 mm: 45 mm: 12x52x90 mm: 9 kW: 2310 mm: 1200 mm: 2050 mm: 2400 kg2 foot pedals for independent work at 2 stationshydr. driveflat bar shearangle bar shear with minimum deformation by diagonal moving of the bladeround and square bar shearrectangular notching unitpunching unit up to diam. 40 mmfast hydraulic, centring deviceoilfillingtable at the punching station with gaugetable at the notching unit with gaugetable at the flat bar shearuser manual in GERMAN and ENGLISHOPTION:Kit € 970,00length stop 1000 mm with contact switch, for angle, flat or bar stationmagnetic machine lamp10 set round punches and dies: 8, 10, 12, 14, 16, 18, 20, 22, 24 and 26 mmThe data for this ad was created with ModulMWS - the software solution of LogoTec ...
: neu : 2025 : 090132 : prompt, Zwischenverkauf v : Türkei : 47500 €: 798.38 €: 1 : 41800 €: 3100 mm: 6 mm: 4 mm: 50 mm: 15 1/min: 1.5 °: 16 : 14 to: 1000 mm: 200 mm/s: 15 kW: 200 l: 2 Stk.: 865 mm: 500 mm: 3515 mm: 4110 mm: 2200 mm: 3700 mm: 2100 mm: 7300 kgSwing cut constructionNC-preselection system D-touch 7 with touch screen for back gauge, cutting length, quantity, USB portMotorized back gauge 1000 mm on ball screws, folding upwardsClear control panel mounted on moveablearmHydraulic hold down pistons are arrangedclose to the cutting edgeFoot switchCentral, manual blade gap adjustmentCutting line illuminationBroad table with ballsPiece counterSingle and continous stokeFold up finger guard 1.000 mm1 squaring arm 1. 500 mm with scale,T-slot and tilting cam2 supporting arms 1.000 mm with T-slotSimple replacement and grinding of thebladesVariable adjustable cuttinglength for eco ...
CNC punching machine manufactured in 2016. This TRUMPF TruPunch 5000 S12 features a working range of 3050 x 1550 mm and a maximum material thickness of 8 mm. It has a maximum punching force of 220 kN and can handle workpieces weighing up to 280 kg. If you are looking to get high-quality punching capabilities, consider the TRUMPF TruPunch 5000 S12 machine we have for sale. Contact us for further details.
10 € 
