subcategories
(3rd category level)
Manufacturer:
(Category: 107)
CONTROLS electronic controls OVERALL SPECIFICATIONS (COIL LINES) sheet width max.: 200 mm sheet thickness max.: 4.5 mm coil weight max.: 0.5 toDECOILER coil weight max.: 0.5 to mandrel expansion range from: 250 mm mandrel expansion range up to: 550 mmLEVELLER UNIT sheet width max.: 300 mm sheet width (min): 20 mm sheet thickness max.: 4 mm sheet thickness min.: 0.5 mm material cross section max. (450 N/mm2): 800 mm² number of leveller rolls: 7 diameter of leveller rolls: 65 mm number of infeed-/outfeed rolls: 4 diameter of feed rolls: 65 mm drive power: 1.5 kW loop controls: yes ELECTRICAL SPECIFICATIONS mains voltage: 380 V mains frequency: 50 Hz
Punching capacity steel: 25x16mm, material strength: 45/60/80kg/mm² depending on hole diameter, angle steel 90°: 110x10mm, angle steel 45°: 90x9mm, T-steel 90°: 110x10mm, T-steel 45°: 90x9mm, U and I profiles: up to NP/IPE 18, round steel diameter: 42mm, square steel: 38x38mm, max. sheet thickness for notching: 12mm, notching width: 50mm. An on-site inspection is possible.
Inv. Num. : 9163 Type: MAH 40/3 CNC Producer: AMOB Created: 2022 Parameters: Diameter of the cylinders: 148 mm Length: 1200 mm Width: 770 mm Height: 1450 mm Weight: 540 kg Hydraulically controlled upper roller feed Can be used vertically and horizontally 3 mechanically driven rollers Side rollers (manually adjustable) Adjustable control pedal 3 standard rollers
Offer 26148 Technical data: - Pressure capacity 420 KN / 42 t - Stroke length 0 - 300 mm - Lifting speed 0 - 0.6 m/min - Tool height 200 mm - Bending performance - with prism MW 125 flat approx. 200 x 16 mm - with prism MW 240 flat approx. 200 x 24 mm - Tube bending up to 2 inches - CNC control SIEMENS SIMATIC HMI TOUCH - For angle programming + length programming - Controlled length stop 3000 mm - Various bending tools - Operating hours (read) 1404 h - Drive 400 V / 4.0 kW - Space requirement approx. W 850 x H 1250 x D 1250 mm - Weight approx. 1200 kg
Key data: 2040 mm, 6 mm
Max. bending length: 2040 mm Max. sheet thickness: 6 mm steel Upper beam stroke: 350 mm Manual and automatic bending process possible Bending angle adjustable via potentiometer Lifting height of the upper beam and material thickness can be preselected via dip switch Motorized adjustment of the bending beam with digital display (adjustment of the sheet thickness) Manual backgauge with spring fingers up to 1500 mm 5700 kg
Max. saw blade diameter: 280 mm Pneumatic material tensioners Swivel table with detent points Minimum quantity spraying device
sheet width: 2050 mmplate thickness: 4.5 mm STpre-bending capacity: 4.0 mm STroll length: 2050 mmmin. dia.: 210 mmroll diam. toproll: 140 mmweight: 1530 kgrange L-W-H: 3220 x 1200 x 900 mm Current new price: approx. 13.000 Euro good condition () Special price upon requestFeatures:- Robust electromechanical plate rolling machine- 2 centrally driven rollers (top and bottom rollers) powered by an electric motor- Manually swiveling top roller with hinged bearing- Includes conical bending device- Freestanding control panel- Manually adjustable bottom roller (via handwheel)- Asymmetrical roller arrangement- Self-braking main motor- Safety device (safety line with switch unit)- CE marking / Declaration of ConformitySpecial equipment included in the price:- Hardened rollers- Motorized adjustment of side rollers- Digital position display for the motorized side rollerThe data for this ad was crea ...
working area: X .. 370 mmworking area: Y .. 700 mmpressure: 28.0 tplate thickness: max. 12.7 mm STthroat: 310 mmheight of stroke: 0 - 40 mmno. of strokes: max. 180 Hub/minpunch diameter: max. 105 mm: 845 x 1420 mmwork height max.: 900 mmoil volume: 50.0 ltotal power requirement: 5.0 kWweight of the machine ca.: 1800 kgrange L-W-H: 1800 x 1200 x 1500 mm New price including accessories approx. 35,000 euros Special price on request The machine was used continuously in a test areaand as a result has very few operating hours !The ECCO LINE hydraulic punching machine has been specially optimized for the processing of sheet metal and profile parts. It is characterized by itsThe machines of the ECCO LINE series are equipped with a punching force ofLINE series are equipped with 28 tons of punching force in conjunction with the proven Trumpf tool system. Tool change time approx. 15 sec (manual)Mod ...
sheet width: 2520 mmplate thickness: 3.0 mm: 350 mmSwing beam adjustment: 80.0 mmback stop - adjustable: ca. 1.000 mmControl: FM 5.1 B upper clamping bar adjustment: 20.0 mm/sekbending speed: 37.0 Grad/sektotal power requirement: 4.5 kWweight: ca. 3.250 kgThe ideal solution for individual and series production.A modern design with particularly high rigidity.Designed for continuous performance.Features:- Dynamic, powerful electro-motorized folding machine Upper beam bending beam drive by geared brake motor Bending beam drive with roller bearings- FASTI CNC control TOUCH - FM 5.1 B Swiveling control unit, front right 11.3 color LCD touch screen display Manual / automatic mode selectable Input of actual/target values possible (X axis / angle etc.) Program memory Tool memory- CNC electro-motorized back gauge with rear sheet support surface- CNC electro-motorized folding beam adjustment- 1x e ...
: neu : ca. 10 Wochen ab Auftrags : Türkei : 52700 €: 996.03 €: 2550 mm: 10 mm: 10 mm: 8 mm: 8 mm: 6 mm: 245 mm: 245 mm: 180 mm: 1,5 / 6 m/min: 7.5 kW: 4800 mm: 1600 mm: 1470 mm: 6170 kg4 rollsTop rolll driven by hydromotor and planetary gearbox, bottom roll driven by gear and cardan systemPinch roll and latereal rolls move with hydraulic cylindersDigital read-out for lower and side rolls positionHardened rollsConical bending deviceHydraulic load relieving of upper rollHydraulic drop-end bearing2 working speedsProtectionagainst overloadMoveable control paneAccording to CE rulesOPTIONAL EQUIPMENT:Infinitely adustable speed of rollsHydraulic side supportHydraulic top supportNC controlIMPORTANT ISSUES AT CONICAL BENDING:The max. sheet metal thickness isequivalent to 50 % of nominal capacityThe cone length can be max. 30 % oremust be more than 60 % of roll lengthHardened rolls are recom ...
: neu : ca. 10 Wochen ab Auftrags : Türkei : 12900 €: 247.68 €: 1550 mm: 3 mm: 110 mm: 3 m/min: 2.2 kW: 2700 mm: 750 mm: 1000 mm: 1200 kg3 rollsasymmetric rolls - prebending2 rolls driven by brakemotormanual Back Rollforward tiltable upper rollforward and reverse revsconical bending by tilt of backrollmovable control panelusers manual in ENGLISH or GERMANOPTIONS:hardened Rolls Motorised Back Roll (Power Rear Roll) Digital Read-OutThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
: neu : ca. 8 Wochen ab Auftragse : Spanien : 25700 €: 490.87 €: 80 to: 500 mm: 5 : 40/14 bzw. 24/24 mm: 70 mm: 40 1/min: 450x15 / 300x20 mm: 130x130x13 mm: 45 mm: 12x52x90 mm: 9 kW: 2310 mm: 1200 mm: 2050 mm: 2400 kg2 foot pedals for independent work at 2 stationshydr. driveflat bar shearangle bar shear with minimum deformation by diagonal moving of the bladeround and square bar shearrectangular notching unitpunching unit up to diam. 40 mmfast hydraulic, centring deviceoilfillingtable at the punching station with gaugetable at the notching unit with gaugetable at the flat bar shearuser manual in GERMAN and ENGLISHOPTION:Kit € 970,00length stop 1000 mm with contact switch, for angle, flat or bar stationmagnetic machine lamp10 set round punches and dies: 8, 10, 12, 14, 16, 18, 20, 22, 24 and 26 mmThe data for this ad was created with ModulMWS - the software solution of LogoTec ...
: neu : ca. 6 Monate ab Auftragse : Taiwan : 50900 €: 962.01 €: 2540 mm: 6.5 mm: Hydraulisch : 135 °: 3900 mm: 1750 mm: 2050 mm: 6200 kghydraulic drivenNC control for bending anglemanual back gauge 600 mmsharp rail 45° (in one piece)front angle beam 75 mmmechanical stop adjustment of upper beamclamping force adjustment of upper beamaccording to CE rulesALTERNATIVELY:versionAMH-K,withSECTIONEDsharp rail 45° € 48.300,--OPTION:2 axes NC control with 7", touchscreen incl. motorized back gauge 800 mm € 11.400,--(sample photos)The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
: neu : 2025 : 090131 : prompt, Zwischenverkauf v : Türkei : 4700 €: 109.71 €: 1 : 50 mm: 155 mm: 2 : 1.5 kW: 4,5 m/min: 60x10 mm / 500 mm, 40x10 : 100x15 mm / 450 mm, 60 x : 35x35 mm / 900 mm, 20x20 : Ø 35 mm / 600 mm, Ø 30 mm : Ø 70x2 mm / 1.000 mm, Ø 3 : 70x30x2 mm / 1.200 mm, 50 : 50x50x3 mm / 1.700 mm, 40 : 50x50x5 mm / 800 mm, 40x4 : 50x50x6 mm / 1.000 mm, 30 : 1050 mm: 750 mm: 1450 mm: 390 kg2 mech. driven rollsstrong cast steel constructionshafts made of special steel,hardened and groundtop roll manual adjustablehardened universal rollslateral rolls adjustable in 1 axishorizontal and vertical operationdouble foot pedal forfor- and backward drivemachine and equipment accordingto the CE regulationsuser manual in GERMAN and ENGLISHWE HAVE MORE THAN 210 REFERENCES!The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
: neu : ca. 12 Wochen ab Auftrags : Türkei : Wechseltisch Laser sources from 3 - 30 kWTable dimensions:3 x 1,5 / 4 x 2 / 6 x 2 / 6 x 2,5 mThe shuttle table is positioned longitudinally, which results in the best possible accessibility for optional loading and unloading systems.The system consists of the following components:Shuttle table system in longitudinal direction for simultaneous loading/unloading and cutting to reduce non-productive production timesEncapsulated cutting room with protective glazingCNC graphics control Siemens Sinumerik 840DLaser source Brilase or IPGCutting head with automatic focus adjustment, Durma or PrecitecCooling unit for cutting head and laser sourceCAD/CAM software LANTEK for programming including autonestingPositioning laserSheet check system (automatic detection of sheet position and dimensions)Automatic nozzle cleaningCentral lubricationSlug boxWorking ...
This 3-axis MicroStep AquaCut-W 4001.20 was manufactured in 2018. It features a working range of 4,000 x 2,000 mm and is equipped with a high-pressure pump system capable of 400 MPa. The machine includes automatic height control for the cutting head and a waterjet cutting table with grid support. If you are looking to get high-quality waterjet cutting capabilities, consider the MicroStep AquaCut-W 4001.20 machine we have for sale. Contact us for further details.
: neu : ca. 10 Wochen ab Auftrags : Türkei : 57000 €: 1077.3 €: 2550 mm: 13 mm: 13 mm: 10 mm: 10 mm: 8 mm: 260 mm: 260 mm: 200 mm: 1,5 / 6 m/min: 7.5 kW: 4800 mm: 1600 mm: 1550 mm: 6800 kg4 rollsTop rolll driven by hydromotor and planetary gearbox, bottom roll driven by gear and cardan systemPinch roll and latereal rolls move with hydraulic cylindersDigital read-out for lower and side rolls positionHardened rollsConical bending deviceHydraulic load relieving of upper rollHydraulic drop-end bearing2 working speedsProtectionagainst overloadMoveable control paneAccording to CE rulesOPTIONAL EQUIPMENT:Infinitely adustable speed of rollsHydraulic side supportHydraulic top supportNC controlIMPORTANT ISSUES AT CONICAL BENDING:The max. sheet metal thickness isequivalent to 50 % of nominal capacityThe cone length can be max. 30 % oremust be more than 60 % of roll lengthHardened rolls are rec ...
: neu : ca. 10 Wochen ab Auftrags : Türkei : 43550 €: 831.81 €: 1550 mm: 12 mm: 12 mm: 10 mm: 10 mm: 8 mm: 220 mm: 200 mm: 160 mm: 1,5 / 6 m/min: 5.5 kW: 3900 mm: 1150 mm: 1250 mm: 3600 kg4 rollsTop rolll driven by hydromotor and planetary gearbox, bottom roll driven by gear and cardan systemPinch roll and latereal rolls move with hydraulic cylindersDigital read-out for lower and side rolls positionHardened rollsConical bending deviceHydraulic load relieving of upper rollHydraulic drop-end bearing2 working speedsProtectionagainst overloadMoveable control paneAccording to CE rulesOPTIONAL EQUIPMENT:Infinitely adustable speed of rollsHydraulic side supportHydraulic top supportNC controlIMPORTANT ISSUES AT CONICAL BENDING:The max. sheet metal thickness isequivalent to 50 % of nominal capacityThe cone length can be max. 30 % oremust be more than 60 % of roll lengthHardened rolls are rec ...
: neu : ca. 12 Wochen ab Auftrags : Italien : 2000 mm: 22 mm: 22 mm: 16 mm: 19 mm: 17 mmHardened and polished rollersNumerical control Siemens PGS-Classic with touchscreenCone bending with electronic control and inclination of the bottom rolleroil coolerSimultaneous rotation and roller movementSimultaneous roller and support movementPossibility to bend variable radii (ovals, ellipses, etc.)Hydraulic micro-positioning by the PLC for higher accuracyInfinitely variable speed for roller movementInfinitely variable speed for rotationPrepared for retrofitting supports (up to 5 axes)Prepared for retrofitting loading/unloading stationsPrepared for retrofitting CNC controlsExtra large, double hinged drop endElectronic parallelism system for the synchronization of the rollersHydraulic lifting of the top roll (for models with a top roll diameter of 205 mm or more)Double linear guide for the movemen ...
: neu : 2025 : 090089 : prompt, Zwischenverkauf v : Türkei : 8900 €: 171.77 €: 1 : 20 to: 185 mm: 200 x 12 mm: 480 x 1060 mm: 200 mm: 80 mm: 10 mm/s: 10 mm/s: 2.2 kW: 930 mm: 1150 mm: 480 mm: 1200 mm: 530 kgProgrammable stroke and retraction pointAdjustable speed and pressureManual jog operation and automatic operating modeHolding pins and tools hardened and ground3 holder pinsBending toolManual stop 400 mmFoot pedalOPTIONS:Cutting-, punching- or pipe bending tools on requestThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
: neu : ca. 12 Wochen ab Auftrags : Italien : 3050 mm: 7 mm: 7 mm: 4 mm: 5 mm: 5 mmHardened and polished rollersNumerical control Siemens PGS-Classic with touchscreenCone bending with electronic control and inclination of the bottom rolleroil coolerSimultaneous rotation and roller movementSimultaneous roller and support movementPossibility to bend variable radii (ovals, ellipses, etc.)Hydraulic micro-positioning by the PLC for higher accuracyInfinitely variable speed for roller movementInfinitely variable speed for rotationPrepared for retrofitting supports (up to 5 axes)Prepared for retrofitting loading/unloading stationsPrepared for retrofitting CNC controlsExtra large, double hinged drop endElectronic parallelism system for the synchronization of the rollersHydraulic lifting of the top roll (for models with a top roll diameter of 205 mm or more)Double linear guide for the movement of ...
new
: neu : ca. 12 Wochen ab Auftrags : Türkei : 13760 €: 264.19 €: 0.4 - 2 mm: 400 mm: 300 mm²: 63 mm: 150 m/min: 10 m/s²FESTO pneumatic systemSIEMENS servo drive and control system7’ colour touch screen SIEMENS2 feed rollersOption:Handwheel and Simlinx remote maintenance module € 4.290,--The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
: neu : ca. 6 Monate ab Auftragse : Taiwan : 56500 €: 1067.85 €: 3100 mm: 6.5 mm: Hydraulisch : 135 °: 4500 mm: 1750 mm: 2050 mm: 6800 kghydraulic drivenNC control for bending anglemanual back gauge 600 mmsharp rail 45° (in one piece)front angle beam 75 mmmechanical stop adjustment of upper beamclamping force adjustment of upper beamaccording to CE rulesALTERNATIVELY:versionAMH-K,withSECTIONEDsharp rail 45° OPTION:2 axes NC control with 7", touchscreen incl. motorized back gauge 800 mm (sample photos)The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
: neu : ca. 12 Wochen ab Auftrags : Türkei : 16000 €: 307.2 €: 2050 mm: 4 mm: 140 mm: 2.2 kW: 3200 mm: 750 mm: 1000 mm: 1650 kg3 reelsasymmetrical roller arrangement - with pre-bending2 driven rollers by means of a brake motormanual Back Rollupper roller can be swiveled forwardforward / reverse runconical rounding by inclining the rear rollersmovable control panelOPTIONS:hardened Rolls Motorised Back Roll (Power Rear Roll) Digital Read-Out (sample photo)The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
: neu : ca. 6 Monate ab Auftragse : Taiwan : 39000 €: 744.9 €: 2035 mm: 2.5 mm: Hydraulisch : 135 °: 3000 mm: 1100 mm: 1750 mm: 2100 kghydraulic drivenNC control for bending anglemanual back gauge 600 mmsharp rail 45° (in one piece)front angle beam 75 mmmechanical stop adjustment of upper beamclamping force adjustment of upper beamaccording to CE rules(sample photo)ALTERNATIVELY:versionAMH-K,withSECTIONEDsharp rail 45° OPTION:2 axes NC control with 7", touchscreen incl. motorized back gauge 800 mmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
: gebraucht : 1968 : 9581 : 3200 €: 1 : 1050 mm: 2 mm: 150 1/min: 500 mm: 1500 mm: 1700 mm: 1100 mm: 800 kgman. back gauge with hand wheel and scaleuser manual in GERMANdidn&apos,t according to CE rulesBUYING USED MACHINERY IS A MATTER OF TRUST - OUR TRANSPARENCY PROMISEWe offer you maximum security and complete transparency.• HONEST INSIGHTS: Detailed photos and functional videos of the current condition• LIVE ON-SITE CHECK: Live testing is possible at our facility• DIGITAL DEMONSTRATION: Individual live demonstration via video call• RISK-FREE PURCHASE: 14-day return policyDetails:https://www.hesse-maschinen.com/en/lp/used-machinesThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
: neu : ca. 8 Wochen ab Auftragse : Spanien : 17800 €: 341.76 €: 80 to: 510 mm: 40x14 mm: 40 1/min: 9 kW: 1700 mm: 1300 mm: 2050 mm: 1715 kghydraulic drivetable with gaugeuser manual in GERMAN and ENGLISHCNC options on requestWe have a big stock of punches and dies for immediate dispatchWE HAVE MORE THAN 700 REFERENCES!The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
: neu : ca. 10 Wochen ab Auftrags : Türkei : 32480 €: 620.37 €: 1550 mm: 9 mm: 9 mm: 7 mm: 7 mm: 5 mm: 180 mm: 180 mm: 150 mm: 1,5 / 6 m/min: 5.5 kW: 3900 mm: 1150 mm: 1250 mm: 3250 kg4 rollsfullhydraulic drive of upper roll and lower rollhydraulic infeed of lower and side rolldigital read-out of lower and side rolls positionhardened rollsconical bending devicehydraulic load relieving of upper rollhydraulic drop-end bearing2 working speedscentral lubrication systemprotectionagainst overloadmoveable control paneaccording to CE rulesOPTIONAL EQUIPMENT (PRICES ON REQUEST):infinitely adustable speed of rollshydraulic side supporthydraulic top supportNC controlIMPORTANT ISSUES AT CONICAL BENDING:the max. sheet metal thickness isequivalent to 50 % of nominal capacitythe cone length can be max. 30 % oremust be more than 60 % of roll lengthhardened rolls are recommendedThe data for this ad ...
: neu : ca. 10 Wochen ab Auftrags : Türkei : 4800 €: 102.29 €: 1270 mm: 1.5 mm: 75 mm: 1.5 kW: 1830 mm: 700 mm: 1160 mm: 400 kg3 rollsasymmetric rolls - prebending2 rolls driven by brakemotorlateral roll adjustable by ratchet leverlongitudinal grooves in lower and lateral rolltiltable upper rollright / left rotation with double foot switchuser manual in GERMAN or ENGLISHOPTION (PRICE ON REQUEST):hardened rollsThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
50 € 
