sheet metal working used for sale (3,347)

Decoiler Coil weight: 2 x 2 ton Material width: 380 - 500 mm Coil exterior diameter: 1.300 - 1.400 mm Expansion range: 445 -530 mm Leveller / Straightener Material width : 40 - 500 mm Number of levelling rolls: 7 pcs. Diameter of the levelling rolls: 60 mm Number of pinch rolls: 2 pcs. Diameter of the drawing rolls: 60 mm Number of pull out rolls: 2 pcs. Diameter of the pull out rolls: 60 mm Material thickness: 0,4 - 1,6 mm Cross section: 800 sq mm Feeding speed: 0 - 30 m / min Required power: 3 kW

Coil weight: 500 kg Material width: 41 mm Coil exterior diameter: 1.000 mm Expansion range: 250 - 500 mm Speed: 20 m / min Required power: 0,5 kW Dimensions L x W x H: 1.000 x 850 x 1.700 mm Weight of machine approx.: 200 kg

sheet width: 3100 mmplate thickness: 6.35 mmthickness at Niro-steel: 4.00 mmcutting angle: 0.5 - 2.5 °cutting gap adjustment: 0.05 - 0.8 mmno. of strokes: 12 - 50 Hub/minback stop - adjustable: 1000 mmControl: DELEM DAC 360 oil volume: 120 ltr.engine output: 9.5 kWweight: 7000 kg.range L-W-H: 3950 x 1950 x 1680 mm well-maintained condition () equipped with new DELEM control unitEquipment:- electro-hydraulic, guided plate shear- DELEM CNC control unit type DAC 360 front control panel, swiveling front left- Electro-hydraulic cutting angle adjustment- Electro-hydraulic cutting gap adjustment- electro-motorized backgauge, with ball screws- 1x extra-long side fence with T-slot mm scaleThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Used Hydr. Adira press brake with CNC controlled crowning WILA Scope of delivery: without tools LazerSafe Security System/CE Foot pedal Two front support arms 500mm, movable Table crowning: WILA motorized Special features: patented HEXA-C frame: low-torsion and therefore very accurate Hydraulics in semi-hybrid equipment very energy-saving because the engine is in the Idle only runs at 5Hz The bounce during start-up and descent is controlled by two high-precision servo valves Two linear encoders ensure accurate positioning of the press beam Adjustable guide of the press beam made of self-lubricating material Electrics and hydraulics with surge protection X&R axis run on backlash-free ball screws driven by servo motors 2 manual stop fingers Z axis Machine rear secured with light barrier AD 60 CNC control type Adcontrol 2 D Machine is repaired, check ...

Roll bending machine manufactured in 2021. This MG MG4R1520C features a working width of 1,550 mm and a bending capacity of 20.0 mm. It includes a CNC TouchCommand EVO control for enhanced precision and efficiency. If you are looking to get high-quality bending capabilities, consider the MG MG4R1520C machine we have for sale. Contact us for further details.

plate thickness: 3 mmangle adjustable from - to: 30 - 120 Gradtable height: 900 mmweight: ca. 800 kgCutting capacity: 3 mm St40 at 150 x 150 mm, 2 mm stainless steel, cutting angle continuously adjustable from 30° to 120°, pneumatic clamping for angle adjustment (Boschert system), machine is in good conditionThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

plate thickness: max. 3 mmdistance betw. rolls: 125 mmthroat: max. 500 mmweight: ca. 500 kgMaterial thickness at 40 kg/mm² tensile strength: max. 3 mmWorking width: 500 mmWorking depth: 450 mmManual adjustment of the upper rollerRoller center distance: 125 mmContinuously variable working speed: 3–15 m/minStop skirt1 set of rollersForward/reverse operation via foot switchThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

contact roller: 70 x 50 abrasive belt size: 2000 x 12/50 power capacity: 2,2 kWOverall size: ca. 400 x 1100 x 1250 mmdeburring machine / free belt frinding machineabrasive belt with widt from 12-50 mm with vertical working positionhead inclination up to 45° both wayseasy bending of the belt allows to follow the shapecutting speed 24m / secbig tabel surface with ball rollingwith self filtering dust extractor system, filtering bag in retardant polyester material for retaining finest dust. Impeller with open blades to prevent clogging. air consumption 700 m³/hcomes with a huge bunch of belts!The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

sheet width: 3050 mmplate thickness: 10.0 mmthickness at Niro-steel: 6.0 - 8.0 mmdown holder: 13 Stückdistance between columns: 3070 mmcutting angle: 1.0 - 4.0 °no. of strokes: ~ 22 Hub/minControl: ELGO P8511 oil volume: 240 lvoltage: 400 Vtotal power requirement: 15.0 kWweight: 8000 kgrange L-W-H: 3550 x 2350 x 1900 mm good condition () from a maintenance workshopEquipment:- NC electro-hydraulic guillotine shears- heavy / stable welded construction (machine body)- NC ELGO digital control unit P8511- NC electro-motorized backgauge on ball screws- electro-hydraulic cutting angle adjustment Front analog cutting angle display- 1x stable side fence, with T-slot and mm scale- 3x stable support arms, with T-slot and mm scale- Ball castors in the work table incl. recessed grips- Front finger guard - can be folded up at the front- 1x freely movable foot switch- 2x front emergency stop button-  ...

: 400 kNstroke length max.: 285 mmworking feed: 9 mm/secreturn speed: 20 mm/sec: 660x1250 mmwork height max.: 930 mmtoolpiece height max.: 250 mmtotal power requirement: 4 kW: 200x26 mmbending capacity max. - round: 60x5,0 mmDomestic equipments:- semi-automatic NC control (99 programs with 16 steps each)- incl. bending bolt (without punch)- Incl. tool holder for dies- incl. foot pedalThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: 40 mm: 8,5 U/min: 120 mmroll diameter: 152 / 162 mmengine output: 1,1 kWconnected load: 400 Vweight: 395 kgOverall size: 900x600x1100 mmEquipment / Accessories:- Two driven rollers- Manual delivery of the upper roller- Working position horizontal and vertical- Bearings with tapered roller bearings- Use of replaceable slide rails on the guide carriage- The standard roller set is included. He can turndifferent profiles are usedThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

bending speed: 2.1 m/minBending capacity - square: 30x30 mmbending capacity - flat iron: 80x15 mmBending capacity - flat iron on edge: 50x10 mmtube diameter: 1 oder 60x2 mmShaft diameter - upper: 35 mmShaft diameter - lower: 30 mmtotal power requirement: 0,75 kwrange L-W-H: 650 x 500 x 1300 mmweight: 170 kgStandard features:- hardened special steel shafts- a set of hardened rollers- Bottom rollers are driven- lateral straightening rollers- Foot pedal- horizontal and vertical workingThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

CNC punching machine manufactured in 2001. This Salvagnini S4-40 features a maximum sheet size of 4064 x 1524 mm and can process materials up to 5 mm thick, including mild steel and aluminum. It includes a versatile H-type punching head with multiple stations for efficient operation. If you are looking to get high-quality punching capabilities, consider the Salvagnini S4-40 machine we have for sale. Contact us for further details.

used Dräco coil carriage, smooth-running spindle, optimal tension, very easy to drive Machine is repaired, checked, cleaned by a specialist and is then fully functional. Test run is being carried out Belt width :1000 mm Coil weight load capacity: 1000 kg Colour: blue Weight: 110 kg Dimensions: 1300 x 750 x 1000 mm Coil inner diameter (min.): 250 mm Coil inner diameter (max.): 515 mm Coil outer diameter (max.): 1100 mm Coil width (min.): 1000 mm Clamping range :280 - 510 mm

Laser marking machine manufactured in 2014. This Trotec Speedmarker 300 features a nominal power of 60W and includes a rotary attachment for enhanced versatility. The workstation is designed with an enclosed Class 2 safety housing, ensuring operator safety while providing visibility. If you are looking to get high-quality laser marking capabilities, consider the Trotec Speedmarker 300 machine we have for sale. Contact us for further details.

serial number: 4412956673057 : 95 to. ca. engine output: 7,5 kWweight of the machine ca.: ca 5 tdimensions of the machine ca.: 2,2 × 1,0 × 2,3 m Technical specifications (from the label)Angle steel (L-profile):150 × 15 mm at 90°100 × 14 mm at 45°Flat steel:up to approx. 150 × 16 mmlarger cross-sections up to 340 × 16 mm (depending on function)Beam profiles:U-profiles (UPN): 220I-sections (IPN)The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

The machine is in good technical condition, after prior agreement it is possible to test it. Head Precitech - Germany, Source IPG. Dior plates changed this year. Automatic change - 2 tables. Table 3x1.5 m.

Inv. Num. : 9090 Type: Trumatic L3030 Producer: Trumpf Created: 2001 Parameters: Maximum power: 3 kW Switch-on hours: 49953 h Laser ON: 48307 Beam ON: 20858 s Work table length: 3000 mm Work table width: 1500 mm Source: TLF 3000 Turbo

Key data: 2000 mm, 500 mm, 500 mm

Manual bending bench, 2 m long, with extendable base frame for installation in transporter

Key data: 1030 mm, 2 mm

Used guillotine shears of the make Fasti type 1030x2.5 Built in 1969

Key data: 3000 mm, 4 mm

Used folding machine of the brand Hera type 3000x4 Year of construction 2000

Key data: 3000 mm, 10 mm

Used guillotine shears of the make Vimercati type 3000x10 Year of manufacture 1997

Key data: 2050 mm, 4 mm

Used guillotine shears of the make Vimercati type 2050x4 Year of manufacture 1997

Beyeler, CP 4100x10, Cutting length : 4100mm, Max. sheet thickness 10mm,

Qty. 1 Second-hand Reversing 4-Hi Cold Rolling Mill Mfc.: NKMZ, ABB, Grip Engineering, Launer Engineering Built: 1972 Type: Reversible Cold Rolling Mill (Quarto-1800) The cold rolling stand has been modernized by ABB in 1995. The mill was fitted with automatic gauge control (AGC), flatness control unit (AFC), spot cooling system (by Grip Engineering), and work roll changing device (by Launer Engineering). Besides, the mill has been equipped with a horizontal rolling Oil filtration system (by Launer Engineering). Flatness & AGC control: available /1995

This 3-axis Durma AD-R 40175 was manufactured in 2022. It features a bending length of 4,050 mm and a bending force of 175 tons, providing robust capabilities for various applications. The machine is equipped with a DURMA DT15 CNC control system and a 3D touch screen interface for enhanced usability. If you are looking to get high-quality bending capabilities, consider the Durma AD-R 40175 press brake we have for sale. Contact us for further details.

Qty. 1 Second-hand 2-Hi Skin Pass Rolling Mill Mfc.: Sir James Farmer Norton Type: 2 - High Temper Mill 318/610 x 710 mm Built: 19 Stopped: 2025 Strip Width: 300 – 600 mm Thickness: 0.3 – 4.0 mm Max. Tensile Force 3000 kg, Coil weight: 10 T

CNC Shearing Machine manufactured in 2022. This Durma SBT 4006 features a cutting length of 4,100 mm and a cutting capacity of 6 mm thickness. It is equipped with a DURMA DT-7 CNC control system for precise operation. If you are looking to get high-quality shearing capabilities, consider the Durma SBT 4006 machine we have for sale. Contact us for further details.

Lg.Nr. 26092 Technical data: - 90° cutting head pneumatically operated - Cutting thickness - normal steel up to 2 mm - Stainless steel up to 1.5 mm - Aluminium up to 3 - Blade length 130 mm - Table size W 600 x D 380 mm - Working height 940 mm - Footswitch - Compressed air requirement 6 - 8 bar - Space requirement approx. W 600 x H 1250 x D 850 mm - Weight approx. 180 kg

Offer 24371 Technical data: - Machine for making closed cold formed corners - Material thicknesses 0.8 to 2.5 mm - max. achievable board height see table - Min. workpiece length / min. workpiece width 120 mm - Production time per shaped corner, regardless of the material 10 sec. - Drive 400 V / 4 kW - Control panel with E – foot switch - Space requirement station 1 approx. W 1100 x H 1650 x D 1100 mm - Weight station 1 approx. 800 kg - Space requirement station 2 approx. W 800 x H 1400 x D 900 mm - Weight station 2 approx. 500 kg