Manufacturer:
(Category: 106)
For sale automatic press PTV 65 produced from SACMI Italy for ropp caps. Tools for 25mm and for 28mm ropp caps.
Furnace 1200 temperature 10 - 1200 Celsius 2 heating zones 100kW auto door PLC Poreba Gurutzpe Tacchi Geminis Tos Amutio cazeneuve Skoda Morando Niles Colchester Heyligenstaedt Kramatorsk Mondiale Safop Cazeneuve Alzmetall mas stankoimport csepel carlton kolb soraluce bergonzi flott Erfurt Weingarten smeral schuler ebu mueller zts kosice wlochy minster Stanko stankoimport glaser huta zygmunt aft donaldson eumuko Elblag Engel Demag Arburg Krauss Maffei Battenfeld Manesty Mazak Voronezh Trumpf Amada Cincinnati Netstal Rose Forgrove Illig Foremost Nissei Sandretto Fette Mazak Mori seiki Haas Okuma Gildemeister Doosan Daewoo traub hwacheon index Wema zeulenroda mueller Erfurt tox presso technik dunkes galdabini hare ponar zeulenrdoda eitel Ziel des Spannungsarmglühens ist die Reduzierung von Eigenspannungen im Material. Solche Spannungen entstehen zum Beispiel durch Gefügeu ...
Nominal force: 4000 tons Slider's undershoot to BDC: 10 mm Slider stroke: 630 mm Frequency of continuous strokes per min: 10 The highest frequency of single strokes per min: 7 Closed height: 1180 mm Adjustment of closed height: 200 mm Slider's dimensions: -From left to right: 5000 mm -From front to back: 2000 mm Dimensions of the plate of the die: -From left to right: 5000 mm -From front to back: 2000 mm Capacity of the main drive: 250 kW Overall dimensions: -From left to right: 7640 mm -From front to back: 5980 mm -Height above floor level: 10490 mm
Tool cases for press-fit machines Tool holder type Haeger (compatible) 22 press-in tools for press-fit-in contact-press-persefesters Manufacturer: PressOne - Made in Finland
Press brake edge machine edge bench press used Manufacturer: Mengele Type: C320-4B Built: 1966 last revision and repair: 2000 Location D-01587 Riesa Dimensions WxH: 6,250 x 3,650 mm Edge knife width: 6,150 mm sheet thickness at 6,000 mm bending length: approx. 7.5 mm. The machines are designed for very deep shaft bends, therefore very deep cheek recesses. Original 300 t pressing force - In 1989 the pressing force was increased to 350 t. The press is in very good condition despite its age. The machine is disassembled and ready for loading. documentation for the machine is available. Weight: about 45 t
Qty. 1 Second-hand crank hot forging press – dismantled & in storage Mfc.: Hyunjin Industry, Korea Built: 2008 Status: dismantled and in storage Force: 2500 T Total weight of the machinery: approx. 250 T
PressOne P1S-5 is a press-fit machine from Finland that is powered by a ball-circuit spindle with servo motor. This gives you the best of both worlds. Power, speed and accuracy. No oil means no leakage problems, no rush of oil changes and no filtration problems. Only pure power, accuracy and speed! Specifications: P1S-5 Main press technology: ball-circuit spindle with AC servo drive Maximum pressing force: 50 kN Repeatability of force adjustment: ± 1% Maximum opening/approach speed: 50 mm / s Pressing speed: max 10 mm / s Extension: 470 mm Stroke length: 210 mm Faster range: M2 - M10 Servo motor: 0.6 kW Control: P1S TC12 Touchscreen 12" Tool connection: Type Haeger, 4-fold lower rotary base The maximum approach speed requires the "Fast Approach Speed" option. Control features of the P1S TC12: - Programmable pressing force - Programmable lifting opening - Program ...
PressOne P1S-10 is a press-fit machine from Finland that is powered by a ball-circuit spindle with servo motor. This gives you the best of both worlds. Power, speed and accuracy. No oil means no leakage problems, no rush of oil changes and no filtration problems. Only pure power, accuracy and speed! Specifications: P1S-10 Main press technology: ball-circuit spindle with AC servo drive Maximum pressing force: 100 kN Repeatability of force adjustment: ± 1% Maximum opening/approach speed: 120 mm / s Pressing speed: max 10 mm / s Extension: 620 mm Stroke length: 210 mm Faster range: M2 - M10 Servo motor: 0.6 kW Control: P1S TC12 Touchscreen 12" Tool connection: Type Haeger, 4-fold lower rotary base The maximum approach speed requires the "Fast Approach Speed" option. Control features of the P1S TC12: - Programmable pressing force - Programmable lifting opening - P ...
PressOne P1S-8 is a press-fit machine from Finland that is powered by a ball-circuit spindle with servo motor. This gives you the best of both worlds. Power, speed and accuracy. No oil means no leakage problems, no rush of oil changes and no filtration problems. Only pure power, accuracy and speed! Specifications: P1S-8 Main press technology: ball-circuit spindle with AC servo drive Maximum pressing force: 80 kN Repeatability of force adjustment: ± 1% Maximum opening/approach speed: 120 mm / s Pressing speed: max 10 mm / s Extension: 620 mm Stroke length: 210 mm Faster range: M2 - M10 Servo motor: 0.6 kW Control: P1S TC12 Touchscreen 12" Tool connection: Type Haeger, 4-fold lower rotary base The maximum approach speed requires the "Fast Approach Speed" option. Control features of the P1S TC12: - Programmable pressing force - Programmable lifting opening - Progra ...
press is after overhaul: full function complete mechanical parts, pneumatic and control system. The press has a new pneumatic clutch, the original was electromagnetic clutch as old system. Press capacity: max. 45 t Pull force: max. 45 t Counter force in pressing position: max. 17 t Stroke of the punch: 175 mm Filling height: max. 140 mm Deduction: max. 85 mm Compression distance: max. 55 mm Top pressing: max. 15 mm Stroke rate: 9 – 26 min.-1 Motor: 7,4 kW Approx: 3000x1200x1800 mm Net weight: about 5000 kg
a hydraulic single-stand drawing press Müller model CLZ.100.1.34, Y.O.M. 1994, good condition, with UVV, Siemens S7 screen control, throat gap 400 mm, installation height 800 mm, table surface 800 x 730 mm, stroke 600 mm, drawing cushion 40 to., drawing cushion stroke 200 mm.
The turret press AMADA EUROPE 245 was produced in 2000 (machine installation: 2001). The price of the machine includes: installation and training in the use of the machine Punching machine technical data: - CNC control: FANUC 18 i-P - working time: 35,000 h - pressure: 20 t - work table: X = 600, Y = 400 - maximum punching format without intercept and with 31 stations head: 1020 x 1290 (Y-10; Y1010 T2XX; Y-50; Y970 T3XX) - maximum size of a punched sheet with an intercept: 1020 x 2540 mm - maximum size of the sheet to be punched with the intercept + 1 revolution (optional): 1500 x 2540 mm - maximum sheet thickness on the ball table: 6 mm - maximum sheet thickness on the brush table: 3 mm - maximum allowable weight on the table: 100 kg - punching accuracy: + -0.1 mm - positioning accuracy: + -0.07 mm - number of pneumatic clamps / grips: 2 - number of axes controlled s ...
Crank press HECKERT PKZ 400.1 built in 1980. Technical data : - maximum pressing force: 400 t - working path - lower position of the slider to the maximum pressing force: 21 mm - maximum drawing depth: 125 mm - pressing force using the maximum drawing depth: 160 Mp - idle speed of the slider: 18 min-1 - maximum number of switchings: 9 min-1 - ram stroke (min-max): 315 mm - slider adjustment: 200 mm - holding force of the drawing device at air pressure: 63 Mp, 5 kp / cm2 - force of the drawing device ejector at air pressure: 10 MP, 7 kp / cm2 - total weight: 38.5 t
Crank press ZAMECH PKRR 400A built in 1974. Technical data : - pressure: 400 tons - clearance between stands: 1020 mm - ram stroke: 315 mm - number of strokes per minute: 20 - maximum distance of the slider from the table closed: 742.5 mm - slider adjustment: 250 mm - table dimensions: 1020 x 1050 mm - main engine power: 40 kW - main engine revolutions: 1500 1 / min. - weight of the press: 40 t
Max shearing power: 315 ton Stroke: 70 mm Single stroke: 30/1 min Square: 100 mm Max billet cut : 106 mm Main motor power: 20 kW Weight: 14 ton
used
Qty. 1 Second-hand press for production of Aluminium pots and discs Mfc.: SITI Built: 2005 Renewed in by experts Duration: 3-4 months Force: 4000 Ton Production of Aluminium discs & induction & normal pots Pots height: 120 / 140 mm The press will be overhauled and revamped and sold as specified below: New Piston Grinding of cylinder New Flange Table modification New pumps New gaskets etc . New electric and electronical parts New program
Stroke power: 180 KN (18 tons). Adjustable speed: 100 - 600 strokes per minute. Adjustable stroke: 4 - 36 mm. In very good working condition. Feeder: BBV 60/60 Max. Strip Width: 60 mm. Max. Feeding Length: 60 mm. Max. Thickness: 2 mm. With stroke and speed counter. Programmable speed, number of strokes etc. Three working modes: manual, one stroke and automatic. Heavy Duty, for non stop production. Pneumatic clutch and brake. Machine with warranty 6 months. Machine dimensions: 600 mm x 600 mm x 1850 mm. Machine weight: approx 1.2 tons. Power consumption: 2.2 KW. Technical Air: 8 bar.
STANZNIETZUFÜHRER Manufacturer: EM HART Teknologies (Tucker GmbH) Type: ERF230000/3 3x5
Pressing force: 160 kN Impact stroke: 100 mm Mounting height: 350 mm Hole in the table: 100 mm Pushhole bore: 32 mm Stand passage: 650 mm Table size: 630 x 400 mm Hydraulic pressure: 280 bar electr. Connection: 380 V, 5.5 kW Space requirement: 1550 x 1050 x 2400 mm Weight approx.: 3 t
Maximum force: 1600 tons Slider stroke length: 400 mm Unattainable-course: 12 mm Number of courses of a slider per minute: 16 Number of single turn-on: 12 The closed height: 870 mm Adjustment: 220 mm Under-forginig plate: -From left to right: 1600 mm -From front to rear: 1600 mm -Thickness: 650 mm Slider overall dimensions: 1600x1600 mm Aperture in a table: 1000x1000 mm window dimensions in cheeks: 1650x1650 mm Course of a rigid pusher in a slider: 100 mm Force of a rigid pusher in a slider ton-force: 80 Main electric motor power: 110 kW Course of pneumatic pillow: 160 mm Force of pushing out of a pneumatic pillow ton-force: 71 Hydropneumatic pillow: -Working course: 250 mm -Force of pushing out ton-force: 25 -Force of a clip ton-force: 250 Press overall dimensions: 4670x4670x8110 mm Press weight: 140 tons
Table press, pneumatically operated Manufacturer K & W Beyer O.H.G Type Q10EL Power at 6 Atü 10 mkg Triggering the movement via electric valve Special price
PressOne P1S-5 is a press-fit machine from Finland that is powered by a ball-circuit spindle with servo motor. This gives you the best of both worlds. Power, speed and accuracy. No oil means no leakage problems, no rush of oil changes and no filtration problems. Only pure power, accuracy and speed! Specifications: P1S-5 Main press technology: ball-circuit spindle with AC servo drive Maximum pressing force: 50 kN Repeatability of the force adjustment: . . . . . . . . . . . . . . . . . Maximum opening speed: 50mm/s Approach speed: 50 mm / s Pressing speed: max 10 mm / s Extension: 470 mm Stroke length: 210 mm Faster range: M2 - M10 Servo motor: 0.6 kW Control: P1S TC12 Touchscreen 12" Tool connection: Type Haeger, 4-fold lower rotary base The maximum approach speed requires the "Fast Approach Speed" option. Control features of the P1S TC12: - Programmable pressing f ...
Capacity, ton 1250 Stroke, mm 500 Min number of no-load stroke: 8 /per min Slider adjustment, mm 215 Max. shut height between bolster plate and slider (stroke down, adjustment up), mm 860 Table size, mm 1600 x 1850 Slider size, mm 1300 x 1400 Table gap size, mm 1100 x 1100 Distance between columns, mm 1630 Distance between slides, mm 1580 Cushion travel, mm 200 Cushion capacity, ton 200 main motor power, kW 90 Press weight, kg 130000
with vertical matrix connector Max. work-piece diameter: 140 mm Max. diameter of upset flange: 180 mm Nominal force of upset slide: 12500 kN Force on clamping slide with dies closed: 12500 kN Stroke of: -Upset slide: 460 mm -Upset slide after closing of dies: 310 mm Number of continuous slide strokes per minute: at least 32 Electric motor power: 75 kW Machine dimensions: -Length: 8035 mm -Width: 4800 mm -Height: 3575 mm Machine weight: 140 tons
Mechanical high-efficiency automatic press Pressing force: max. 150kN Ejection force: 50kN Die support in pressing position: max. 150kN Return force of lower punch: max. 32kN Closing force of upper punch: max. 12kN Upper punch stroke: 90mm Upper punch adjusting travel: 60mm Stroke rate: 8...40strokes/min
- The largest diameter of the workpiece, mm 90 - The maximum diameter of the planted flange, mm 120 - Rated force of the landing slide, kN 6300 - The force perceived by the clamping slide with closed dies, kN 6300 - stroke of the landing slider, mm 350 - The stroke of the landing slide after closing the dies, mm 230 - The frequency of continuous idle slider per minute, not less than 42 - Power of the electric motor 45 - Dimensions, mm length 4835 width 3450 height 2880
Max. diameter of initial blank: 30 mm Blank length: -Min.: 120 mm -Max.: 300 mm Max. diameter of upset flange: 60 mm Upset slide nominal force: 2500 kN Max. force on clamping slide with dies closed: 2500 kN Stroke: -Movable die: 100 mm -Upset slide (full): 220 mm -Die closing: 140 mm Slide strokes per minute: 45 Machine overall dimensions: -Length: 6050 mm -Width: 4600 mm -Height: 2260 mm Machine weight: 24680 kg
