Manufacturer:
(Category: 106)
Dear Sir or Madam, We have in the offer for you The Tiger metal and scrap press.These are available with different press box dimensions and Bale dimensions (25 x 25, 30 x 30, 40 x 40). Cutting edges on all three sides of the box give the machine the ability to handle oversized materials. The machine is equipped with side pre-loading box, oil cooler and radio remote control. (further equipment possible) Out of stock. If you have any questions, please do not hesitate to contact us. To make an offer, we need your company data and a direct e-mail address.
Air steam die forging hammer : Capacity : 16 tons, Nominal mass of drop parts : 16000 kg, Impact energy : 400 KJ, Ram stroke : 1500 mm, Ram stroke per minute : 20, Distance clear between guides : 1180 mm, Ram dimensions front to back : 1500 mm, Die holder dimensions front to back : 1600 mm, Bottom die impression to floor distance : 500 mm, Steam/air pressure : 0.7-0.9 MPa, Overal dimensions : - Floor space : 4500 x 2450 mm, - Height above floor level : 7920 mm, Mass of anvil block : 325 tons, Total weight of hammer : 425 tons.
Compressive force: 170 t Spindle Ø: 160 mm Table support surface: 700 x 900 mm Plunger area: 500 x 800 mm Gr. Distance between table and plunger: 450 mm Drive motor: 380 V, 11 kW Weight: 8200 kg
Year: 2021 (brand new machine, immediately available) - stable cast iron construction - hydro-pneumatic controls - adjustable position of the heads - lowered thrust unit (30 mm hoof) - profile supports - scissors stroke: 10.5 mm - working stroke of the clamp: 80 mm - crimping height: 120 mm - crimping point: 30-60 mm
PKZZ 250 Double Column Crank stamping Press Completely overhauled. Electric and Control- Not available. Table 2500 x 1400 mm Ram 2320 x 1250 mm Distance between uprights 2525 mm Window in table width 2300 mm Window in table depth 850 mm Stroke 400 mm Strokes per minute SPM 12 Adjustment of ram 120 mm Shutheight 550 mm Table cushion force 50 to Cushion stroke 160 mm Motor 32 kW Weight ca. 39 tons
Maximum force ton-force 400 Slider stroke length mm 250 Number of courses of a slider per minute 25 Maximum distance between table and slider (in lower position of slider) mm 670 Table overall dimensions: mm - from front to rear 1000 - from left to right 1000 Main electric motor power kW 40 Press overall dimensions mm - length 3410 - width 3140 - height 5930 Press weight kg 30 600
Specification: Nominal force: 2500 ton Ram stroke: 190 mm Number of strokes in 1 minute: 20 Shut height: 800 mm Bolster plate-to-ram adjustable stroke: 15 Table size: 1250x1400 mm Weight 124.230T
Specifications: - Hole diameter approx. 44 , 45 , 48 , 52 , 2 x 55 , 2 x 58 , 61 , 66 mm 2 x 68 , 2 x 80 , 81 , 85 mm - Long hole dimension approx. 12 x 42 , 12 x 50 , 18 x 55 mm - Stamp holder 58 mm - Stamp height 54 + 58 mm - Adapter ring for stamps - Die height 30 + 40 mm - Die outer diameter 90 + 140 mm - Adapter ring for matrices 90 - 140 mm - Weight approx. 90 kg
Schuler PE4s 50/800 High Speed Press Manufacturer: Schuler Type: PE4s 50/800 High-speed press 61/21 600/3 Pressing force: 50 t Projection: 800 mm Stroke rate /min: 125-300 Plunger stroke: 40 mm Kohler unwinding reel 500.1 M We sell a large number of paternosters. The devices are in operation until 30.06.2021. After the purchase, there are also the documents for it From 01.07.21 the devices are ready for collection. Dismantling and transport by the buyer. Location is Hildesheim The dismantling, loading, as well as transport can alternatively be offered by us. In addition to about 50 paternosters, countless other machines are available. After purchase, the amount is due within 7 working days. Please also note our other offers. Have fun browsing and buying.
- Pressing force: 1000 kN pressure: 289 bar - Piston stroke: 300 mm - Downward speed: 10.5 mm/s - Working speed: 2.7 mm/s - Return speed: 15 mm/s - Passage: 1050 mm - Table dimensions: 1030 x 460 mm - Table height adjustment: 600 mm / 5 steps - Stop adjustment: 400 mm - Pressure stamp Ø: 110 mm - Guide piston Ø: 60 mm - Motor power: 7.5 kW - Connection voltage: 400 V - Dimensions WxHxD: 2000 x 2150 x 900 mm - Weight: 1250 kg
- Pressing force: 1500 kN - Pressure: 300 Mpa - Piston stroke: 300 mm - Downward speed: 9.8 mm/s - Working speed: 2.6 mm/s - Return speed: 13 mm/s - Passage: 1550 mm - Table dimensions: 1530 x 500 mm - Table height adjustment: 750 mm / 5 steps - Stop adjustment: 400 mm - Pressure stamp Ø: 2x 150 mm - Guide piston Ø: 70 mm - Motor power: 7.5 kW - Connection voltage: 400 V - Dimensions WxHxD: 2150 x 2050 x 1000 mm + 750 x 1100 x 750 mm - Weight: 1800 kg
pressure: 320 tchamfer lenght: 4000 mmdistance between columns: mmtotal power requirement: kWweight of the machine ca.: 25 tdimensions of the machine ca.: mBrand: LVDType: PPEB 320/40CNC brand: MorrisCNC model: Solutions ESA 630Year of make: 1990HydraulicCapacity: 320 TBend length: 4.000 mmMulti V + J-kniveSteered backstop X+RIncl. 1 Set of toolsMachine weight: 25.000 kgMachine is flat on the groundThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
pressure: 300 tworking feed: 9 / 14 mm/secstroke: 600 mmcolumn daylight: 1550 mm: 600 adjustment of press crosshead: 1500 mmslide adjustment -horizontal: 3000 mmtank capacity: lfeed speeds: 9 mm/secreturn speed: 14 mm/sectotal power requirement: 18,5 kWweight of the machine ca.: 35 tThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
pressure: 2000 /1000 tdistance between columns: 2650 mmstroke: 500 mmcolumn travel -side: 500 x 1000 mmdiameter of piston: 710 mmnumber of pistons: 2 distance between table / ram: 1000 mmoperating pressure: 130 / 230 bardayligth: 800 mmtable length: 2500 mmtable width: 1600 mmtable height: 250 mmdraw back pressure: 500 kNnumber of T-slots: 8 turning speeds: 1500 U/minrapid speed: 120 - 140 mm/minclosing speed: max. 120 - 140 mm/sec.hydraulical ram locking: return of plunger by small single cylinders: 100 - 110 mm/seccutting sound absorber: 300 tdie cushion capacity: 200 tdie cushion stroke: 250 mmspeed of die cushion: 100 mm/secvoltage: 380 Vfrequency: 50 Hzquantity of oil: 2000 ltotal power requirement: 93 kWweight of the machine ca.: 90 tdimensions of the machine ca.: 5000 x 2500 x 7200 mmtransport measurements: ca. 6500 x 3750 x 2190 mm1991 assembly of a die cushion, pressure reducti ...
pressure: 17,0 kNstroke: 60 mmthroat: 105 mmWorking height from to: 75 -180 mmtable surface area: 170 x 130 mmspindle diameter: 25 mmweight of the machine ca.: 35 Kgdimensions: 260 x 130 x415 mmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
pressure: 1,5 kNstroke: 40 mmthroat: 70 mmWorking height from to: 75 - 170 mmtable surface area: 115 x 70 mmweight of the machine ca.: 11 Kgdimensions: 115 x 175 x 290 mmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
pressure: 17,0 kNstroke: 40 mmthroat: 110 mmWorking height from to: 70 - 220 mmtable surface area: 190 x 140 mmspindle diameter: 30 mmweight of the machine ca.: 60 Kgdimensions: 310 x 190 mmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
pressure: 100 tpassage width: 1000 mmstroke: . mmwidth: 800 mmtotal power requirement: kWweight of the machine ca.: tdimensions of the machine ca.: mThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
press capacity: 250 tspindle diameter: 160 mmram stroke range: 180 mmstroke speed: 71 Hub/mincolumn daylight: 450 mmtable surface area: 560x450 mmram surface: 450x400 mmtotal power requirement: 12 kWweight of the machine ca.: 9 tdimensions of the machine ca.: mThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
pressure: 100 tstroke: 300 mmCylinder: 205 MMdistance between table / ram: 520 mmtable surface area: 1100X350 mmram surface: 350X350 mmtotal power requirement: 7,5 kWweight of the machine ca.: tdimensions of the machine ca.: mThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
pressure: 100 tno. of strokes: 30-70 Hub/minMax ram stroke: 130 mmram adjustment: 100 mmtable surface area: 950x630 mmram surface: 630x600 mmthroat: 340 mmdayligth: 480 mmcoil: GSW total power requirement: kWweight of the machine ca.: 8,9 tdimensions of the machine ca.: mThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
pressure: manuell tdistance between columns: 50 mmdayligth: 50 mmtotal power requirement: kWweight of the machine ca.: 0,01 tdimensions of the machine ca.: 0,3 x 0,3 x 0,3 m• 4 units available,• bore at bottom, Ø 10 mm,• thread in spindle M 6,The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
pressure: 200 tchamfer lenght: 3000 mmdistance between columns: 2560 mmdayligth: 450 mmthroat: 450 mmadjustment of stroke: 240 mmhorn length over column outer edge each: 175 mmtable length: 3050 mmtable width: 280 mmtable height over floor: 820 mmelectrics - voltage/frequency: 220/50 V/Hzcontrol: CYBELEC, DNC60 stroke: 250 mmoperating pressure: 150 bartotal power requirement: kWweight of the machine ca.: 15 tdimensions of the machine ca.: L:4,0 x B:3,2 x H:3,44 m• hydraulical press brake, • new control CYBELEC DNC60 (in 2005),• lower part of the machine moves down 500 mm to the floor, at the moment the machine is mounted on a double-T-support,• prism and upper part of the machine in 3000 mm lengthThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
The nominal gain kN 4000 Slide stroke, mm 400 Frequency Slider strokes min-1, 25 The frequency of single strokes, min-1 19 Slider travel to its lowest position, where the press develops the rated force, mm 8 The distance between table and slider in its lower position at the upper adjustment position, mm 470 Size of adjustment of distance between table and slider, mm 160 The size of the table, mm 1000x1000 The size of the slide from front to back, mm 800 Width of windows in racks mm 600 Main electric motor power, kW 37.0 Air flow, m3 / stroke 0,017 Press overall dimensions, mm left to right 3470 front to back 3140 Height above floor level, mm 5940 Weight without hydro pillow kg 32600
pressure: 140 tchamfer lenght: 3000 mmdistance between columns: mmtotal power requirement: kWweight of the machine ca.: tdimensions of the machine ca.: mStocknumber 2010012Type of machine PressbrakeMake COLLYType 3000/140Build in nbChamfer lenght 3000 mmPressure 140 tonStroke 250 mmThroat 310 mmDaylight 520 mm Additional informationincl. 1 set of toolingThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
The LVD EHT DELTA 1250 RS TK turret punching machine was built in 1999. It is equipped with a MNC 32000 CNC control. The punching machine has a maximum pressure of 20 tons and allows the processing of a sheet with dimensions of 1250×1250 mm and a thickness of 4.5 / 6 mm. The machine performs a maximum of 650 beats per minute. The press is equipped with a hydraulic system, a turret with four stations (A, B, C, D) and a clearance adjustment sensor G8823142. Technical parameters: – CNC control: MNC 32000 – maximum pressing force: 20 tons – sheet dimensions X x Y: 1250 x 1250 mm – sheet thickness: 4.5 / 6 mm – maximum number of strokes: 650 1 / min – rated number of strokes: 300 1 / min – oil tank: 200 L – total power: 18.7 kW – engine: 11 kW – voltage: 400 V – weight: 17 tons Hydraulic System – Thick Turret: – instrumentation: station A, B, C, D ...
pressure: 320 tthroat: 800 mmstroke: 630 mmdistance between table / ram: max. 1000 mmram head dimension: 710 x 600 mmtable-size: 800 x 1200 mmwork height max.: 1015 mmquantity of oil: 1100 lNumber of working hours: 7663 hweight of the machine ca.: 15 tdimensions: ca. 1600 x 2200 x 4800 mmdimensions of switch cabinet: ca. 1200 x 400 x 1800 mmTested for function. During the test run it is noticed that the press ramnot 100% leak-proof.In addition, the cable for manual operation was mended several times.Upper cover is missing, since this was dismantled by the customer due to crane use.Operating instructions and electrical plans available.The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
pressure: 63 tdistance between columns: 0 mmstroke: 160 mmtable surface area: 630 x 500 mmdayligth: 400 mmtotal power requirement: kWweight of the machine ca.: 5 tdimensions of the machine ca.: mThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
closing pressure: 4360 kNtable-size: 730 x 730 mmcontrol: B+R Industrieelektronik draw back pressure: 190 kNajustment speed: max. 60 mm/secreturn speed: max. 90 mm/secdaylight between the columns: 900 mm= vulcanizing press with vertical closing unit, with form removal and form separation deviceThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
NOTE additionally a new shaft Description Force , 4000 TN Slide stroke, mm 400 Number of continuous slide stroke, stroke / min 50 Closed height of stamping space mm 1000 Adjusting the table mm 15 Distance between columns in light,mm 1660 Drive power, kW 185 Table dimensions in plan mm: - From left to right in 1620 - Front-to-back in 1570 Dimensions in mm: - in the plan 6100 x 4710 - Height above floor level 6820 - Press height 8680 Weight, t 377
