Pressing force: 8 t Table surface: 450x260 mm Stroke: 250 mm Projection: 175 mm Lifting speed: 3.9 m/min Retraction force: 4,000 kg Engine: 4 hp Weight approx. 1 t
No. 4877: 1 gebr. Single-stand hydraulic press Fabr. EITEL, Type T 6.3, Bauj. 1973
pressure: 20 tthroat: 185 mmstroke: 100 mmtable surface area: 380 x 350 mmtotal power requirement: 4 kWweight of the machine ca.: 1 tThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
pressure: 100 tthroat: 320 mmstroke: 160 mmtable surface area: 850 x 550 mmdayligth: 500 mmoil volume: ca. 500 lram surface: 560 x 450 mmtotal power requirement: 30 kWweight of the machine ca.: 6,5 tdimensions of the machine ca.: 1,5 x 2,0 x 3,0 mMachine was overhauled in 2008- Workroom enclosure with Sick light barrier- Large ram with ejector and pin clampThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
pressure: 63 tthroat: 280 mmstroke: 160 mmtable surface area: 560 x 500 mmram surface: 280 x 280 mmdayligth: 400 mmoil volume: ca. 360 ltotal power requirement: 22 kWweight of the machine ca.: 4 tdimensions of the machine ca.: 1,45 x 1,75 x 2,67 m- Workroom enclosure with Sick light barrier- Large ram with ejector and pin clamp- foot switch- Motorized depth stop in the cylinderThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
hydraulic drawer, used hydraulic single column drawing press , used Type: CEZ 160.5.9 Built / new in: 1978/1992 Manufacturer / make: Müller Pressing force / rated pressure: 160 t Max piston stroke / max. piston stroke: 560 mm Table size / table size: 740 x 710 mm Table hole/ hole in table: 200 mm Pestle surface / slide surface: 200 mm Extension / depth of gap: 360 mm Mounting height / height of table: 480 mm Printing power of the draw cushion/ force cushion: approx. 40 t Pressure piston diameter / diam. of piston: 200 mm Weight: 7.9 t Connection value / connected load: approx. 31 kW
Inv. Num. : 6047 Type: OP 200 Producer: NEFF Created: 2006 Parameters: Control system: SIEMENS Simatic S7-300 Compressive force: 200 t Top table length: 1700 mm Top table width: 900 mm Total power requirement: 75 kW Ram stroke: 595 mm Machine height: 5500 mm Machine length: 2100 mm Machine width: 3100 mm Machine weight: 26000 kg Equipment: Technical Documentation Automatic ramming oil lubrication
Compressive force 100 tons. Plunger stroke 360 mm Installation height 560 mm Table area 1000 x 650 mm Table opening Ø 150 mm Plunger area 1100 x 600 mm Clamping pin bore Ø 50 mm Table height over corridor 900 mm Tank capacity hydraulics 450 liters Drive power 22 kW Mains connection 400 Volt, 50 Hz, - Tappet stroke manually adjustable via electrical position initiators - Fine adjustment pots for lifting speeds - Fine adjustment pot for press force adjustment - Light barrier (not attached) Weight 7800 kg
The machine is in excellent technical condition, almost in the condition of a new machine. The purchase price of the machine was 900,000 CZK. Possibility of examination by prior arrangement. Machine weight: 4500 kg Machine dimensions (WxDxh): 1470 x 2220 x 3420 mm Rated pressure force: 500 kN Working pressure: 280 bar Impact clamp surface: 800 x 600 mm impact stroke: 600 mm impact speed (optional): 10/20 mm / s
Pressing force: 100 t Projection: 320 mm Stroke: 300 mm Installation height: 500 mm Table clamping surface approx.: 1,000 x 600 mm Impact clamping surface approx.: 600 x 320 mm Table height above corridor: 950 mm Rapid traverse from: 400 mm/s Working speed: 50mm/s Rapid traverse on: 400 mm/s Die cushion force in the table: 25 t Die cushion stroke: 100 mm Ejector in the plunger: 5 t Ejector lift in plunger: 50 mm Drive power: 45 kW Weight machine : 11,8 t
Pressing force 1000 kN Table size 750 x 560 mm, diarrhoea opening 100 mm Installation height 800 mm, stroke 500 mm Projection 360 mm Bear size 530x400 mm, 2 T-slots Ram speed: down 200 mm/sec, up 400 mm/sec Connection load approx. 21 kW Incl. Feeder WE16 for 160 mm bandwidth Coil tray and straightening unit Fabr. OFFICE; Type CA200/R40-7, YOC 1994 Reel, loop control Two-hand operation Manuals
