sheet metal working used for sale (3,273)

round bar steel: 33 mmsquare edge steel: 30 mmL-beam: 60 x 8 mmhole diameter in sheet thickness: 20 in 13 mmhole punhing press: pressure: 35 thole punching press: throat: 320 mmhole punching press: max. length of stroke: 24 mmhole punching press: capacity (dia. x thick.): 30 x 9 mmhole punching press: capacity (dia. x thick.): 20 x 13 mmtotal power requirement: 1,5 kWweight of the machine ca.: 1,7 tdimensions of the machine ca.: 1,5 x 0,7 x 1,8 mProfile steel shear with:- Hole punch- Notcher- Foot switch- Machine light- Mounted on a trolleyThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Univ. Flanging Machine Specifications: - Flanging machine for raising right-angled borders, on straight, round and curved sheet metal parts. - Drive 400 V - Space requirement approx. W 650 x H 1250 x D 650 mm - Weight approx. 200 kg

Hand-operated 3-roll sheet metal round bending machine with asymmetrical roller order Specifications: - Working width max. 1020 mm - Material thickness max. 1.5 mm - Roller diameter 64 mm - Upper roller turned into a crown, can be swung forward - Rear shaft with handwheel diagonally adjustable for conical rounding - Lower roller adjustment with control lever and eccentric - Front shaft parallel - Space requirement approx. W 1250 x H 950 x D 750 mm - Weight approx. 200 kg

FRAMECAD FL650 roll forming line was built in 2009 in New Zealand by Framecad Solutions Ltd. This state-of-the-art and compact production line is used in the production of precision C- and U-type cold-formed profiles, used as steel floor joists in a wide range of construction projects. The entire machining process is fully automatic and is performed with the highest accuracy. The strip, with a maximum thickness of 1.95 mm, is uncoiled from the coil towards the workspace with a roll forming system. Each profile is precisely formed, cut, punched and individually marked. Large service holes are also made to facilitate the assembly of electrical, HVAC and plumbing systems. The FRAMECAD roll forming line is operated via a touchscreen panel with an intuitive interface that significantly simplifies the daily work of the operator. The full integration of advanced design software with the cont ...

FRAMECAD TF550 roll forming line was built in 2009 in New Zealand by Framecad Solutions Ltd. This state-of-the-art and compact TF series (Truss and Frame) production line is an excellent choice for the mass production of fabricated solutions for the residential and commercial buildings. This is because the FRAMECAD TF550 enables the production of C- and U-type cold-formed profiles in various sizes (150 mm as standard), used as rafters, trusses and steel structures in a wide range of building projects. The entire production cycle is fully automatic. The strip, with a maximum thickness of 1.6 mm, is uncoiled from the coil towards the workspace, where it is machined by means of a special roll forming system. The profiles are accurately formed, cut, punched, dimpled and marked, making them ready for simple assembly with screws. The machine is operated via a touchscreen panel with an in ...

FRAMECAD F300i roll forming line was built in 2009 in New Zealand by Framecad Solutions Ltd. This state-of-the-art and compact production line is the perfect choice for the efficient production of lightweight steel structures. This is because the FRAMECAD F300i enables the precise forming of C- and U-type cold-formed profiles of various dimensions (89 mm as standard), which are used in, among others, partition walls and bathroom modules. The machining process is fully automatic. The strip with a maximum thickness of 1.2 mm is uncoiled from the coil towards the workspace with a special roll forming system. Each profile is precisely formed, cut, punched, and marked, making them ready for direct assembly with screws. The FRAMECAD F300i roll forming machine is controlled via a touch panel with an intuitive interface. The full integration of advanced design software with the controller  ...

Key data: 4000 mm, 12000 mm, 12000 W

4000 x 2000mm 12000w

A hydraulic profile-steel/universal steel shear with integrated punching unit Muhr & Bender is available. Punching force: 500kN, punching capacity for 15mm steel: 25mm, punching stroke: 60mm, stroke rate: 47/min, throat depth: 750mm, installation height: 215mm, working height: 1150mm, flat-steel cutting capacity X/Y: 180mm/20mm. Machine dimensions X/Y/Z: approx. 1500mm/900mm/1900mm, weight: approx. 2000kg. Includes various round and slotted punches with dies. An inspection on site is possible.

pressure: 40.0 tchamfer lenght: 1270 mmdistance between columns: 1000 mmcolumn arm: 200 mmstroke: 100 mmdayligth: 308 mmajustment speed: 150 mm/secworking feed: 1-10 mm/secreturn speed: 100 mm/sectable width: 100 mmtable height: 900 mmcontrol: DNC 60 PS oil volume: 100 lvoltage: 400 Vtotal power requirement: 5.5 kWweight of the machine ca.: 2750 kgEquipment:- CNC electro-hydraulic press brake- CYBELEC DNC 60 PS CNC control Swiveling control panel, front left Tool & program library- CNC electro-motorized backgauge (X-axis) X-axis travel = 800 mm 2x manually adjustable backgauge fingers (R+Z axes) Backgauge on ball screws- CNC controlled axes Y1 - Y2 - X- Rehfuß upper tool system A with quick-change clamping Additional crowning device in the tool holder- 4V universal die block with 60 mm die shoe- 2x sliding material/support arms (Sliding System)- BOSCH/HOERBIGER hydraulic system- SIEMENS ...

A hydraulic large-format sheet metal shear Schneider is available. Width: 6020mm, bending length: 6000mm, max. sheet thickness at 6000mm: 10mm. With position display. An on-site inspection is possible.

Key data: 3 mm, 1050 mm

Notching Machine COMACA type N/EPAS Maxi Sheet thickness: 3 mm Table size: Length 1050 mm x Depth 700 mm Ends tables dimensions: 900 x 470 mm Throat depth: 110 mm Orientable stop Blade length: 225 x 225 mm Voltage: 380 V Total length with ends tables: 2900 mm Length: 1200 mm (with retreated ends tables) Depth: 800 mm Total height: 1100 mm Weight: approx 1 T

Max. bending length: 2040 mm Max. sheet thickness: 4 mm steel Max. upper bolster stroke: 350 mm Manual and automatic bending process possible Bending angle adjustable via potentiometer Lifting height of the upper beam and material thickness can be preselected via toggle switch Bending rail in top condition Manual backgauge with spring fingers 4000 kg

Qty. 1 Second-hand Copper Strip Production Plant – Still in Production Mfc.: J. F. Norton, Shinkwang Tech, Partec, Rozai, Chungwon Control & Sunil, Handuck R-FECO, Mirae Tech Inc., Changjo, Wuishi, Youngchang Machinery, Dongshin Tech., Sonoda Engineering Co., Wuxi Longar Mach., Backsan Machinery, Youngdong Coil Center, Deakwang Machinery, Hanguk E.N.G, Built: 1962, 1965, 1990. 2000, 2001, 2008, 2017, 2018, 2019, 2020 Revamping: 2017, 2019, 2020, Scope of supply: Roughing Mill Mfc.: Famer Norton Type: 4-Hi Irreversible – WR Drive 318 x 610 x 635 mm Built: 1965. 06 Revamping: 2017. 09 by Shinkwang Tech Strip width: 200 – 530 mm Thickness: 3.0 – 12 mm Intermidiate Mill Mfc.: Shinkwang Tech Type: 4-Hi Irreversible, WR Drive - 225 x 570 x 720 mm Built: 2017. 06 Revamping: 2020 by Partec Strip Width: 200 – 650 mm Thickness: 0.8 – 5.0 mm Finishin ...

Offer 25493 Specifications: - Cutting length 3050 mm - Cutting thickness at 400 N/mm², strength 13 mm - Cutting thickness at 400 N/mm², strength up to 1000 mm, length 15 mm - Cutting angle 0.5 - 3 ° - Number of sheet hold-downs 18 pcs - Stroke rate 10 - 23 min -Mot. Back gauge up to 1000 mm - Rear area protection with light barrier - Front angle stop 1000 mm - HSLX version: - CNC control HACO SC 5 controller when entering the sheet thickness in mm -Auto. Cutting angle adjustment according to sheet thickness - Cutting length limitation -Auto. Positioning of the backgauge (8 programs – 80 sets) with - Digital display and autom. Backgauge retraction - Possibility of mot. Adjustment of the backgauge by 2 push buttons - Drive 400 V / 22 kW - E - Footswitch - Space requirement without support arms approx. W 4200 x H 2250 x D 2200 mm - ...

sheet width: 1270 mmplate thickness: 2,0 mmdistance between columns: 1295 mmdaylight opening: 46 mm: 135 °total power requirement: Handbetrieben weight of the machine ca.: 0,4 tdimensions of the machine ca.: 1,6 x 0,8 x 1,2 mSegment bending machine, new.Segment widths:25, 30, 35, 40, 45, 50, 75, 100, 150, 200, 250, 270 mm.Including material stop, max 660mmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

sheet width: 1070 mmplate thickness: 4 mmdistance between columns: 1100 mmdiameter of upper rolls: 110 mmtotal power requirement: 5,0 KWweight of the machine ca.: 1,2 tdimensions of the machine ca.: 2,0 x 0,9 x 1,1 mmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

sheet width: 1070 mmplate thickness: 9.0 / 10,0 mmdistance between columns: 1070 mmdiameter of upper rolls: 190 mmpre-bending capacity: 9,0 mmconnected load: 5,3 kWweight of the machine ca.: 2,4 tdimensions of the machine ca.: 2,7 x 0,92 x 1,2 mm- Electrically adjustable rear roller- Electrically adjustable lower roll (material clamping)- Digital readout for rear roller movement- Digital readout for lower roll movement (material clamping)- Hardened rolls- Conical rolling- Swiveling top roll- Brake motor- Emergency stop- Documentation- 400VThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Key data: 6400 mm, 1 mm

used Jorns double bending machine, with the following equipment: - 4 pneum. Clamping finger with short-part clamping finger - Attachment rail - Foot control - Sheet metal cassettes - Upper beam with rebate groove - Hydr. Material thickness adjustment - Clamp and angle stop (Matic) Machine is repaired, checked, cleaned by a specialist and is then fully functional. Test run is carried out. Working length 6400 mm Sheet thickness max. steel 1.5 mm Sheet thickness max. aluminium 2.0 mm Sheet thickness max. VA 1.0 mm Back gauge (min.) 15 mm Back gauge (max.) 1125 mm Colour anthracite/light grey Total power requirement 20 A Dimensions 7332 x 3721 x 2040 mm Weight 9250 kg Upper beam stroke (opening width) 200 mm Bending angle (max.) 145 degrees Crowning manual without roller scissors Number of stands 5 pieces Insertion depth 1150 mm Machine number K13036

BODOR P3015 fiber laser was built in 2020 in China by Jinan Bodor CNC Machine Co.,Ltd. Distinguished by its use of the most advanced technology available on the market, the machine is the perfect choice for even the most intensive challenges. It enables the precise machining of sheet metal with a maximum length of 3000 mm and a width of 1500 mm by means of a stable 2 kW fibre optic beam. During the machining process, the cutting head with autofocus automatically adjusts the focal position depending on the thickness of the material. The nozzles, in turn, are automatically changed, calibrated and cleaned to ensure reliable operation throughout their service life. All this is completed by the 360° anti-collision system developed by BODOR, which predicts and detects any obstacles. The BODOR P 3015 fibre laser is also extremely easy to operate. The machine operator has an advanced nume ...

BODOR T230 tube and profile fiber laser was built in 2020 in China by Jinan Bodor CNC Machine Co.,Ltd. The machine, which is distinguished by its use of the state-of-the-art technology available on the market, is the best choice for even the most demanding tasks in many industries. It enables precise cutting of tubes and profiles with a square cross-section by means of a stable 1 kW fibre-optic beam. During the machining process, the cutting head with auto focus function stores the focal length values in the control system separately for each type of material. The intelligent technology developed by BODOR, in turn, reduces the piercing time by 90%, regardless of the thickness and type of material. All these solutions reduce energy consumption and the amount of cutting gas to a minimum. The T230 tube laser cutting machine is also extremely easy to operate. The machine operator has an a ...

IZAN MAKINA IZFORM IZ5 roll forming line was built in 2019 in Turkey by İzan Makina – İmalat İnşaat İç ve Dış Ticaret Limited Şirketi. This line, distinguished by the use of the state-of-the-art technology available on the market, is designed for frame constructions. Its extensive machining capabilities allow for the precise, fully automatic forming of C- and U-type cold-formed profiles of various dimensions. These elements are used, among others, in partition walls and bathroom modules. The IZAN MAKINA IZFORM IZ5 profiling machine is offered with extensive equipment, including advanced BIM software and a sheet metal decoiler with a maximum capacity of 3 tonnes. The IZAN MAKINA IZ5 rool forming machine is currently configured for the production of C75x1.2mm and C100x1.2mm profiles. The production cycle is performed by means of a reliable tool head with the following machini ...

pressure: 35.0 tchamfer lenght: 1250 mmdistance between columns: 1095 mmstroke - stepless adjustable: 215 mmcolumn arm: 410 mmtable height: 800 mmdayligth: 455 mmworking feed: 10.0 mm/secreturn speed: 56.0 mm/secwork height max.: ca. 875 mmControl: DM 51 Number of working hours: ~ 13.300 hoil volume: 80.0 loperating pressure: max. 240 barvoltage: 380 Vtotal power requirement: 4.0 kWweight: 2500 kgrange L-W-H: 1700 x 1450 x 2250 mmFeatures:- Robust CNC-controlled hydraulic press brake- With DELEM CNC control unit DM 51” Positioning of the backgauge (X axis) Positioning of the depth adjustment (Y1+Y2 axis) Program + tool storage possible Swiveling control panel, front left- CNC electric motor-driven backgauge (X axis)- CNC electric motor-driven height adjustment of the stop (R axis)- 2x manually adjustable stop fingers- 1x split set of deer foot tools - top- 1x split set of Multi V tools ...

Offer 25500 Specifications: - Cutting length 3050 mm - Cutting thickness at 400 N/mm², strength 13 mm - Cutting thickness at 400 N/mm², strength up to 1000 mm, length 15 mm - Cutting angle 0.5 - 3 ° - Number of sheet hold-downs 18 pcs - Stroke rate 10 - 23 min -Mot. Back gauge up to 1000 mm - Rear area protection with light barrier - Front angle stop 1000 mm - HSLX version: - CNC control HACO SC 5 controller when entering the sheet thickness in mm -Auto. Cutting angle adjustment according to sheet thickness - Cutting length limitation -Auto. Positioning of the backgauge (8 programs – 80 sets) with - Digital display and autom. Backgauge retraction - Possibility of mot. Adjustment of the backgauge by 2 push buttons - Drive 400 V / 22 kW - E - Footswitch - Space requirement without support arms approx. W 4200 x H 2250 x D 2200 mm - ...

: 300 kNstroke length max.: 235 mm: 200x24 mmbending capacity max. - round: 60x4,0 mmtoolpiece height max.: 250 mm: 660x1250 mmwork height max.: 900 mmreturn speed: 20 mm/secworking feed: 10 mm/sectotal power requirement: 3 kWweight: 950 kgDomestic equipments:- semi-automatic NC control (99 programs with 16 steps each)- incl. bending bolt (without punch)- Incl. tool holder for dies- incl. foot pedalEquipment:- Stamp, smallest U = 145 mm 85 °   H = 250 mm, R = 5 mm- Quick change Monomatrize 85 °   H = 250 mm, V = 63 mmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

2005 Amada EM2510NT Excellent condition 45 stations, 4 indexing No loading system A lot of tools and spares Books

Inv. Num. : 8497 Type: HSLX 3008 Producer: HACO Created: 2016 Parameters: Maximum cutting length: 3000 mm Maximum cutting thickness: 8 mm Back gauge: 1000 mm Equipment: Set of knives Truck with rear handling

- Two-roller technology - 180° arrangement of wheels - Closed work area with coolant and lubricant equipment - Hydraulic roundabout centering device - Gearbox with oil circulation lubrication -Temperature Specifications: Workpiece diameter (max.): 360 mm Blank diameter (max.): 380 mm Workpiece length (max.): 600 mm Center width (max.): 1,340 mm Tip width (min.): 200 mm Tool holder DIN 55026: Gr. 11 Force per axis (transverse) (max.): 117 kN Axle force (longitudinal)/feed axle (max.): 140 kN Stroke (transverse): 190 mm Stroke (longitudinal): 690 mm Feed axis speed: (max.) 1.8 m/min Rapid traverse (longitudinal): 7.0 m/min Adjustment roller (axial): 0-20 mm Stroke ejector: 380 mm Ejector force: 26 kN Tailstock stroke: 800 mm Tailstock force: 5-19 kN Speeds (infinitely adjustable): 6-231-387 min-1 25-850-1,550 min-1 Main drive (DC motor): 33  ...

- Gearbox with oil circulation lubrication - Blank counter holder (optional) - Processing unit KA - behind the machine (optional) - Specifications: Blank diameter (max.): 1,200 mm Tip width : 900 mm Tool holder DIN 55027: Gr. 11 Axis force (transverse) (max.): 20 kN Axis force (longitudinal) (max.): 30 kN Stroke (transverse): 360 mm Stroke (longitudinal): 750 mm Cross speed: (max.) 3.0 m/min Longitudinal speed: (max.) 2.0 m/min Stroke ejector: 400 mm Tailstock stroke: 750 mm Speeds (9 levels): 42-660 rpm Main drive: 11 kW Hydraulic drive: 7.5 kW Operating voltage: 400 V Frequency: 50 Hz Connected load: approx. 20 kVA Weight: approx. 6,000 kg

- Hydraulic roundabout centering device - Blank counter holder - Machining unit BAE 1 (on the spindle box) optional 2. - Processing unit KA (in front of the machine) Specifications: Blank diameter (max.): 700 mm Tip width : 825 mm Tool holder DIN 55027: Gr. 6 Axis force (transverse) (max.): 22 kN Axis force (longitudinal) (max.): 20 kN Stroke (transverse): 250 mm Stroke (longitudinal): 400 mm Transverse speed: (max.) 6.0 m/min Longitudinal speed: (max.) 6.0 m/min Stroke ejector: 200 mm Tailstock stroke: 400 mm Speeds (infinitely variable): 100-2,800 rpm Main drive: 11 kW Hydraulic drive: 7.5 kW Operating voltage: 400 V Frequency: 50 Hz Connected load: approx. 20 kVA Weight: approx. 3,500 kg

- Hydraulic roundabout centering device - Blank counter holder - Machining unit BAE 1 (on the spindle box) optional 2. - Processing unit KA (in front of the machine) - Double reel seat Specifications: Blank diameter (max.): 700 mm Tip width : 800 mm Tool holder DIN 55027: Gr. 6 Axis force (transverse) (max.): 22 kN Axis force (longitudinal) (max.): 20 kN Stroke (transverse): 250 mm Stroke (longitudinal): 400 mm Cross speed: (max.) 7.0 m/min Longitudinal speed: (max.) 7.0 m/min Stroke ejector: 200 mm Tailstock stroke: 400 mm Speeds (infinitely variable): 100-3,800 rpm Main drive: 11 kW Hydraulic drive: 7.5 kW Operating voltage: 400 V Frequency: 50 Hz Connected load: approx. 20 kVA Weight: approx. 7,000 kg