subcategories
(3rd category level)
Manufacturer:
(Category: 107)
Trumpf TruMicro 6 kW laser source High-power disk laser with nanosecond pulses. The high-power nanosecond lasers of the TruMicro Series 7000 are based on disk laser technology and combine short pulses and high pulse energies even at high frequencies. This allows you to remove layers and dirt at top speed and reduce your cycle times. Further optimize your processes by varying the repetition rate – while maintaining the same pulse duration The short-pulse lasers of the TruMicro Series 7000 are the ideal tool for efficient and economical cleaning of tire molds. Large-area applications with high medium power Ablating, cleaning, tempering: The TruMicro Series 7000 lasers show their full performance in large-area applications. With pulse energies of up to 100 mJ, they achieve enormous decoating rates. A scanner ensures excellent performance utilization. Flexible las ...
Key data: 3020 mm, 1 mm
in good condition, POS 400 control with digital display, without stop system, with standard rail Machine is repaired, checked, cleaned by a specialist and is then fully functional. Test run is carried out. Working length: 3020 mm Sheet thickness steel: 1.5 mm Sheet thickness aluminum: 2.0 mm Blechdicke VA/sheet thickness Stainless 1.0 mm Colour: white/blue Dimensions: 3930 x 700 x 1175 mm Machine weight: 2120 kg Motor power: 0.55 kW Upper bolster stroke: 120 mm without cutting device for cutting to length Bending angle (max.: 145 degrees Machine number: 180928
- Forming rolls R30/40/50/60/70/80/90/100- Under power good running order- Documentation drawings availebel-
tube diameter: 60.3 x 4.5 mm STtube diameter: 60.3 x 5.4 mm ALUtube diameter: 2 x 3.91 mm GASbar material - diameter: 35.0 mmrevolutions per minute: 2.0 U/minbending radius min.: 10.0 mmbending radius max.: 270 mmexternal diameter: min. 5.0 mmexternal diameter: min. 1/8 Zollvoltage: 230 Vtotal power requirement: 1.5 kWweight: 76.0 kgrange L-W-H: 302 x 243 x 674 mmEquipment:- mandrel-less tube bending machine- Model M = ELECTRO-HYDRAULIC SINGLE-PHASE- high performance and compact design- completely hydraulic machine- bends 210° without the need to catch up- no electronic control- Ercolina patent n. 102017000142179- control of the bending angle via adjustable angle scale- mobile machine base BENDING SEGMENT AVAILABLE AT AN EXTRA CHARGE The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Key data: 8020 mm, 3 mm
with hydraulic scissors, emergency stop rail, attachment rail, control on the swivel bracket, radius adjustment. The connection Hydraulic power unit is behind the machine. Machine is repaired, checked, cleaned by a specialist and is then fully functional. Test run is carried out. Working length: 8020 mm Sheet thickness steel: 3.0 mm Sheet thickness aluminum: 4.0 mm Sheet thickness front: 1.5 mm Back gauge (max.): 1000 Radius: 1020 Colour: grey/blue Total power requirement: 46 A Space requirement: 10,000 x 2,300 mm Insertion depth: 1000 Machine weight: 8000 kg Oberwangenhub: 200 Roller shears: 3.0mm Number of stands: 10 with cutting device for cutting to length/ Öffnungsweite_ h 200 Max. bending angle: 143 crowning without underbeam adjustment Back gauge (min,) 15 Machine number: 09488-01/K19149
Offer 25425 Technical data - Motorized upper roller 175 x 30 mm - Continuous lower rollers 250 x 50 mm - Upper roller can be delivered by handwheel - Top roller diameter 175 mm - Lower roller diameter 250 mm each - Projection 1100 mm - Distance base plate – lower roller 1520 mm - Drive 400 V - Space requirement approx. W 900 x H 2650 x D 2000 mm - Weight approx. 1500 kg
High-precision and versatile punching/nippling machine Boschert Compact 500 CNC Z (built in 2011) – Ideal for flexible sheet metal processing! We sell a powerful and reliable punching/nippling machine from the quality manufacturer Boschert, which convinces with its extended equipment and precision. This machine is the ideal solution for a wide range of Spectrum of punching and nipple tasks, from individual parts to large series. Features that convince: • Manufacturer: Boschert • Type: Compact 500 500 x 1000 CNC Z • Year of manufacture: 2011 • Intuitive CNC control: Multi-axis Ladob control with graphical user interface for easy Programming and visualization of the machining processes. • Extended working range for greater flexibility: o X-axis: 0 - 2000 mm (allows the machining of long workpieces) o Y-axis: 0 - 750 mm (offers generous space for wide sheets) ...
used
Key data: 2 mm, 12 mm
Cut-to-length line 2,000 x 12 mm Bandwidth. 2,000 mm Tape thickness... 4-12 mm Coil weight 30 tons. Straightener 11 reels Speed 15 m/min. Main Engine. 200 KW Voltage. 380 V / 50 Hz.
chamfer lenght: 0900 mmplate thickness: mmdistance between columns: 900 mmpressure: 20 tcolumn arm: 230 mmstroke length max.: 150 mmtravel -x axis: 350 mmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Slitting line 2,100 x 14 mm Bandwidth... 2,100 mm Strip thickness 4-14 mm Coil weight.. 35 tons. Coil Diam. I 508-810 mm Coil Diam. Rewinder 750 mm Coil A Dia. 2,000 mm Knife shafts diameter 380 mm Connected load 660 KW
Key data: 2 mm, 10 mm
Sheet Straightener 2,000 x 10 mm Execution.. 4high Blechdicje . 3-10 mm Straightening rollers.. 13 pcs. Straightening rollers durcm.. 145 mm Support rollers Duchm 290 mm Weight... 32,000 kg Drive mot... 30 KW
Slitting line 500 x 0.3-2.5 mm Coil weight . 7 to. Coil I diam 508 mm Coil A Dia. 1,300 mm Coil I Dia. Expenditure. 400 mm Strip number 2-25 Speed 1-150 m/min. Working Guidelines right/left
Coil turner, usable as a stand-alone machine for dressing coils of all kinds, or at the end of a slitting line for setting up sliced coils as a transfer for a coil packaging system.
Shear force 60 t Punching force 40 t Profile steel shears L- and T-irons at 90° 100 x 10 mm at 45° 65 x 8 mm Notching device with square notch for sheet metal up to 10 mm Flat steel shears for flat steel 380 x 8 mm or 150 x 14 mm Weight: approx. 1.5 t Dimensions: approx. 1.7 x 1.05 x 1.98 m Accessories - Electrical contact stop 3000 mm - Anchor table - Adjustable hold-down device - Tool package Validity of the security check until Feb. 2026
Offer 25455 Hydr . Flat profile and bar steel shears with notching device and hole punch Technical data: - Flat steel shears cut up to 300 x 15 mm - Profile steel shears - Cuts L-steel at 90° to 120 x 12 mm - Steel bar shears - Cuts round steel up to 40 mm - Square steel up to 35 mm - Notching device - with square notch. 100 x 42 x 10 mm - Hole punch - punching force 600 KN - With stop table - Projection 220 mm - Punches in steel up to 28 mm Ø in 15 mm - or 38 mm Ø in 11 mm - various punches + dies, - Drive 400 V / 4 kW - Space requirement approx. W 600 x H 1550 x D 1500 mm - Weight approx. 1300 kg
Punching force: 1000 kN Projection: 760 mm For example, punch a 40 mm hole in 22 mm steel Stroke release via foot switch Quick-change device Range of tools is included in the price 3000 kg
Offer 25437 Technical data: - Pressure capacity 500 KN - Stroke infinitely adjustable 10 - 32 mm - Stroke rate 22 - 27 1/min - Projection 510 mm - Installation height 350 mm - Drive 400 V / 4 kW - Holes e.g. up to 27 mm Ø in steel 14 mm - With special punching saddle, e.g. up to 39 mm Ø in steel 9.5 mm - e.g. up to 90 mm Ø in steel 4 mm - Space requirement approx. W 700 x H 1700 x D 1200 mm - Weight approx. 1150 kg - with: - Hydr. Low-Pressure Grain Locator - Long punch holder for punching in sectional steel - Roller conveyor with plier feed control PEHU 101 - Roller conveyor approx. 6000 mm - Footswitch - Emergency stop button
Offer 25507 Technical data: - Max. working width 2520 mm - Max. material thickness 2.0 mm - Cutting angle 2.2 ° - Stroke rate up to 25 1/min - Back gauge with ELGO positioning control up to 750 mm - Table height 850 mm - Front angle stop 2000 mm - 2 front support arms 1000 mm - pneum. Supported sheet metal hold-up - E-footswitch - Typing - Single stroke pre-selectable - Rear protection grille - Drive 400 V / 3 kW - Space requirement approx. W 3450 x H 1150 x D 2200 mm - Weight approx. 1600 kg
FEEDSTOCK STEEL STRIP sheet thickness max.: 4 mm sheet thickness min.: 0.8 mmPRODUCT (PROFILE, TUBE) external diameter min.: 24.9 mm external diameter max.: 60 mm wall thickness min.: 0.8 mm wall thickness max.: 4 mmLINE CHARACTERISTICS Forming Process: rollforming welding process: HF inductive sawing process: travelling system consisting of:- large coil reel- Bandschweisseinrichtung- optional: horizontal band loop- side planer- forming unit- HF welding unit- units for outside scarfing, inside scarfing - each without impeders, tooling- cooling section- calibration unit with alternative calibration station for ovals, polygons- flying saw- chip blow unit- hexagon bundling- and binding unitoptional roll-sets available for:forming section:26,30, 32, 36, 38, 40, 44, 46, 52, 60 mmcalibration section:25, 26, 29.5, 29.89, 30, 32, 33, 33.4, 33.5, 33.7, 34, 35, 36, ...
FEEDSTOCK STEEL STRIP sheet thickness max.: 4 mmPRODUCT (PROFILE, TUBE) external diameter max.: 51 mm specifically suitable for the welding of USM furniture tubes -Large reel without storage-Strip welding device-Side planer-Calibrating roll stand-Forming unit-HF welding unit THERMOTOOL-Unit for scraping without tools -Cooling section-Calibrating unit-Flying saw-Removal section for manual removal-Roller sets for 19, 20, 25, 35.9, 36, 37, 40.8, 41 mm-Various accessories and machine-specific spare parts-Documentation and maintenance logs-CE declaration
sheet width: 3100 mmplate thickness: 6.0 mm STpre-bending: 4.0 mm STdiameter of upper rolls: 200 mmside roll diameter: 165 mmdiameter of lower rolls: 190 mmbending speed: ca. 5.0 m/minControl: DIGI oil volume: 80.0 Litervoltage: 380 Vtotal power requirement: 6.0 kWweight: 6000 kgrange L-W-H: 5250 x 1500 x 1400 mm very good condition () Current new price approx. 80,000 euros Special price on requestFeatures:- Robust electro-hydraulic 4-roll bending machine 4-roll concept offers a wide range of bending and rounding options- MG swivel control panel Operation - control of all rolls and machine axes Digital position display Manual operation via joysticks- Two central rolls are driven directly by hydraulic motors- Conical rolling possible via inclined position of the rolls- Parallelism of the side rollers via torsion shafts- Bending on both sides- Diameters of up to 1.1 times the upper roller ...
table length: 3048 mmtable width: 1524 mmburner heads: 1 stroke: 270 mmspeed: 100 m/mindimensions: 8900 x 2260 x 2220 mmweight of the machine ca.: 7.500 kgThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Stock number: 4017 PROFILE BENDING MACHINE Manufacturer: Roundo , Type: R4 Machines NO.: 1735, Year of manufacture: 1977 Specifications: Angle steel 90x9 mm Flat steel 200 x 30 mm Frame steel upright 100 x 18 mm Round steel 60 mm Load by steel 40 Kg/mm2 30 cm3 Upper roller 275 mm Ø Shaft dia. 105 mm Square steel 55 x 55 mm T-steel 90x10 mm Total power 5.5 kW Length: 1500 mm, Height: 1400 mm, Width: 1400 mm, Weight: 2500 kg
working pressure: 300 bartotal power requirement: / kWweight of the machine ca.: 1 tdimensions of the machine ca.: mThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Manufacturer: Trumpf TYPE: TC L 2530 Year of Make: 2000 Working space / travel: 2580 x 1305 x 115 Weight: 8450KG Automation: Plate changer Laser: CO2, 2400W Strahlein: 29,000 hrs Laserein: 41,000 hrs Footprint: 6,500 x 4800 Accessories: Top ́s lite Plate changer Works flawlessly
Key data: 4050 mm, 6 mm
Year of construction 1988 Cutting length 4050 mm Cutting capacity 6 mm Weight approx. 8500 kg Knife renewed about a year ago.
MICROSTEP MSF-Pipe-T 6501.200L tube and profile fiber laser was built in 2018 in Slovakia by MicroStep spol. S.r.o. The machine, which is designed for precision cutting of tubes and profiles of various cross-sections and non-standard shapes, is an excellent choice for modern business. This is because a number of state-of-the-art technical solutions guarantee the most accurate cutting results throughout its entire service life. 2D or 3D cutting is performed by means of a stable 2 kW fibre optic beam, which is generated by a resonator of the highest energy efficiency. The 3D laser scanner accurately measures the workpiece before machining to determine its actual shape along the cutting trajectory. Advanced algorithms then allow the control system to appropriately adjust the movement of the cutting tool and supports, as well as compensate any workpiece inaccuracies. The work area is c ...
AMADA LC-1212 ALPHA III laser cutting machine was built in 1999 in Japan by AMADA CO., LTD. The machine is used for precision machining of sheet metal with a maximum weight of 220 kg. Laser cutting is performed by means of a stable 2 kW laser beam, which guarantees the achievement of extremely smooth edges with no irregularities. All this is complemented by an advanced NC control and a laser source of the highest energy efficiency. The AMADA LC 1212 A3 laser cutting machine weighs 4500 kg. Technical specifications of the AMADA LC-1212 ALPHA III laser - laser power: 2 kW - number of axes: 3 (X,Y,Z) - feed in the X/Y/Z axis: 1270/1270/300 mm - rapid traverse in the X/Y/Z axis: 80/80/60 m/min - working speed: 20 m/min - maximum sheet metal dimensions (L x W): 2540 x 1270 mm - maximum sheet metal weight: 220 kg - work table height: 820 mm - positioning accuracy: ± 0.01 mm - pos ...
QC11K 18×6000 hydraulic guillotine shears were built in 2018. This highly efficient machine is designed for precision cutting of sheet metal made from e.g. steel, non-ferrous metals, as well as selected plastics. Workpieces with a maximum thickness of 18 mm are machined by means of high-quality cutting knives with four cutting edges. All process parameters, on the other hand, are programmed on the intelligent DELEM CNC control with an intuitive interface and many useful functions. The QC11K 18×6000 guillotine shears weighs 40000 kg. Technical specifications of the QC11K 18×6000 guillotine shears - maximum cutting length: 6000 mm - maximum sheet metal thickness (Rm=420 N/mm2): 18 mm - maximum sheet metal thickness (Rm=700 N/mm2): 12 mm - work table height: 900 mm - back stop stroke: 1000 mm - adjustable gap between blades and cutting angle - motor power: 21 kW - power supply ...
TRUMPF TruLaser 5040 6kW laser cutting machine was built in 2012 in Germany by TRUMPF Maschinen Grüsch AG. The machine has been continuously serviced, upgraded and maintained throughout its service life. A set of quartz tubes, all internal optics and the lamp were replaced in September 2022. A cleaning and calibration of the external optics, meanwhile, was performed in September 2025. All filters and oils were changed on an ongoing basis according to TRUMPF recommendations. Water was changed once a year, along with flushing of the CU and AL circuits. All these activities are confirmed by the corresponding service reports. The TRUMPF TruLaser 5040 (L18) laser cutting machine is the perfect choice for any industrial plant. It enables precision cutting of sheet metal made from, among others, steel, aluminium, copper and brass. Laser cutting is performed by means of a stable 6 kW laser b ...
