Manufacturer:
(Category: 106)
Make: MABU Model: 25 VPR. Made in Germany. Max. Pressure: 250 [kN] (25 [T]) Speed range: 80-400 [spm]. Year of manufacture: 1998. Operating modes: Manual, One-cycle and Automatic. Equipped with two hand start and foot-clamp start. Fixed stroke: 17 [mm]. Ram adjustment: 40 [mm]. Max. Tool dimensions: 400 x 400 [mm]. Power: 3 [kw]. Current: 230 / 400 [V]. Air connection: 5.5 [bar]. Feeder: Silicon SFS 200 on left-hand side. Max. strip width: 200 [mm]. Machine dimensions: H 2350 x W 1700 x D 1400 [mm]. Weight of machine: cca. 2500 [kg]. Electrical cabinet with Mabu Pf 1.3 control. Front and rear safety guards with inspection glass. Technical documentation and operating instructions in English and German included. CE certificate and EUR-1 certificate of origin. On stock, tested and ready for delivery. More used machines from Mabu, Bruderer, Bihler and Schaal available ...
Hydraulic press 1500 tons. Clearance between the two side pistons = 1400 mm. Clearance between uprights = 400 mm. Vertical clearance between open boards 3200 mm. Moving table dimensions = 1700 x 1800 mm. Fixed table size = 1500 x 2000 mm. This press has been used to produce forks for forklift.
FEINTOOL GKP F 100T fine blanking press was manufactured in Switzerland in 1974. The machine, distinguished by its robust, stable design, can perform several demanding machining steps in one precise process, saving time and labour. Workpieces with a maximum thickness of 6 mm thus achieve an extremely even surface and precisely defined edges that are impossible to achieve on other machines. The machining process can be fully automated when the FEINTOOL GKP F 100/160 hydraulic blanking press is retrofitted with a sheet metal feeder. The total weight of the machine is approximately 9 tonnes. Technical data of the FEINTOOL GKP F 100T hydraulic press - maximum workpiece thickness: 6 mm - maximum sheet metal width: 210 mm - total force including auxiliary functions: 160 t - shearing force: 100 t - hydraulic counterweight force (upper table): 1-40 t - hydraulic force of ring jaw (lower ...
Technical characteristics Nominal force, mc 1600 Not reach the slide to BDC, mm 12 Progress in the slide, mm 400 The frequency of continuous strokes, min-1 16 The highest frequency of single strokes, min-1 12 Closed height mm 870 Adjusting the closed height 220 mm Size slider, mm left to right 1600 front to back 1600 Dimensions plate, mm left to right 1600 front to back 1600 Power of main drive, kW 110 Dimensions, mm left to right 4670 aft 4670 height above floor level 8110 W 154 000kg
pressure: 100 tthroat: 345 mmstroke: 20-100 mmno. of strokes: 60 Hub/minram - range of adjustment: 85 mmtable surface area: 980x650 mmram surface: 600x440 mmhole in the table: Ø 200 mmtable height: 820 mmtool hole in ram: ¤7 65 mmweight of the machine ca.: 7 tdimensions of the machine ca.: 2000x2000x2900 mmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Effort 2000t moving matrix 280 mm landing pad 570 mm landing slider after closing the matrices 390 mm Number of moves of the ram, stroke / min 25 Electric motor power 160 kW Dimensions, mm: LWH = 856053604850, the level above the floor is 3200. Weight of the car without electricity: 239.8 tons. Weight of the bed: Front part: 82 tons. Rear part: 55t. Weight 270 ton
Qty. 1 Second-hand extrusion press including log furnace Mfc.: SMS Built: 1986 Force: 960 MT (9.3 MN) Press jaw: Wide: 155 mm Height: 140 mm Max. inlet: 130 mm (144 mm block, 5 mm protection per side) Recipient: 149,9 mm Extras: Heatable tool cassette from Marx (installed 2016) Conversion of recipient to resistance heating (beginning of 2016) Punch press disc: 149,2 mm Broaching disc: 150 mm Billet Ø: 144 mm Length: 265 – 540 mm Log length: 3000-4800 mm Log Furnace Mfc.: Extrutec GmbH Built: Temperature: 480-520 °C Zone 1: 460-490 °C Zone 2: 440-470 °C Zone 3: 400-450 °C Table weight: Max. 1350 g/m Min. 80 g/m Electrical control cabinet Puller Exhausting system Cooling device Spare parts for furnace combustion air Spare parts hea ...
Key data: 75 t
Specifications: Capacity 75 tons Stroke rate 90 strokes Projection 300 mm Plunger stroke 16 - 140 mm Plunger adjustment 80 mm Table size approx. 800 x 600 mm Installation height max. approx. 400 mm
Capacity, ton 630 Stroke path till its position where it develops nominal capacity, mm 16 Slider stroke, mm 320 Slider strokes, spm 20 Max. distance between table and slider, mm 800 Distance adjustment between table and slider, mm 180 Table size, mm 1250 x 1250 Slider dimensions, mm 1000 x 1000 Opening in the table, mm 800 x 800 Thickness of bolster, mm 180 Cushion stroke, mm 130 Main motor power, kW 58 Machine dimensions, mm 3280 x 3470 x 6190 Machine weight, kg 55500
pressure: 55 tthroat: 200 mmstroke: 10-80 mmram - range of adjustment: 60 mmno. of strokes: 120 Hub/mintable surface area: 600x450 mmram surface: 290x230 mmtable height: 850 mmtool hole in ram: Ø 40 mmweight of the machine ca.: 3,5 tdimensions of the machine ca.: BxTxH 2000x2000x2700 mmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
pressure: 40 tthroat: 195 mmstroke: 8-78 mmno. of strokes: 76-190 Hub/minram - range of adjustment: 60 mmtable surface area: 650x380 mmtable height: 840 mmhole in the table: Ø 110 mmram surface: 250x350 mmtool hole in ram: Ø 40 mmtotal power requirement: 3 kWweight of the machine ca.: 2,2 tdimensions of the machine ca.: BxTxH 1450x1220x2110 mmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
pressure: 63 tthroat: 320 mmstroke: 8-100 mmno. of strokes: 120 Hub/minram - range of adjustment: 63 mmtable surface area: 730x600 mmram surface: 540x360 mmtable height: 850 mmtool hole in ram: Ø40 mmweight of the machine ca.: 5,5 tdimensions of the machine ca.: BxTxH 2000x2000x3000 mmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
pressure: 200 tchamfer lenght: 3050 mmdistance between columns: 2550 mmControl: CYBELEC VisiTouch Pac stroke of ram: 524 mmweight of the machine ca.: 17.000 kgThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
pressure: 100 tchamfer lenght: 2050 mmdistance between columns: 1550 mmthroat: 250 mmstroke: 200 mmadjustment of press crosshead: 200 mmstroke speed - idle stroke downwards: 105 mm/secstroke speed - idle stroke upwards: 180 mm/secstroke speed - under load: 9,5 mm/sectable width: 200 mmtable height over floor: 900 mmdayligth: 280 - 480 mmback stop - adjustable: 3 - 729 mmcontrol: CYBELEC SYNCHRO control: CNC 7400 PS total power requirement: 7,5 kWweight of the machine ca.: 10 tdimensions of machine L x W x H: 3,70 x 2,45 x 2,80 mAccessories: programmable back gauge, table extensions, various upper and lower dies segmentsThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Offer 22564 Specifications: - Printing capacity 150 t - Working width 2600 mm - Passage between uprights 2100 mm - Table width 180 mm - Projection 250 mm - Installation height 325 mm - Drive 400 V / 7.5 kW - Space requirement approx. W 3000 x H 2400 x D 1600 mm - Weight approx. 7000 kg - With: - Two-hand control panel with foot switch
pressure: 2500 ttable length: 5200 mmtable width: 2300 mmPRESS FORCES: • CAPACITY : 2500ton• Point pressure capacity: • - Upper 1600t• - Down 900ton• Slide stroke: 650mm• Slide adjustment: 225mm• Slide stroke number: continue 9~25spm • Die-height: 1250mm• Slid size(LxR ,FxB): 5400x2400mm• Bolster size(LxR, FxB, T): 5200x2300x200mm• Balance capacity: 30ton• Main motor: DC 355kw• Feed back(bolster upper side): 700,780mm• Feed back stroke : 550,700,1000mm• Cramp stroke : 0-250mm• Lift stroke: 0~150mm• Transfer inner size(cramp): 650~2200mm • Die cushion capacity• No.1 station 120ton• No.2 station 80ton• No.3 station 60ton• No.5,6,7 station: 5ton• Stroke: 200mm• Bed size: 480x1780mm• Stop time: 430msThe data for this ad was created with ModulMWS - the software solut ...
pressure: 25 tthroat: 200 mmstroke: 4 - 80 mmtable surface area: 595 x 410 mmram adjustment: 70 mmno. of strokes: 150 Hub/mintable adjustable in height: 240 mmtotal power requirement: 1,1 kWweight of the machine ca.: 1,45 tdimensions of machine L x W x H: 1,30 x 0,80 x 2,0 mThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Offer 20202 Specifications: - max. pressing force 35 t - Projection to the middle of the ram 240 mm - Working height adjustable with hand crank 540 to 940 mm - 2 Hand control - Protective shield enclosure with light barrier - Material - Slide-in device - Pneumatic connection - Press control via SIEMENS SIMATEC OP 7 - Drive 400 V / 15.5 kW - Space requirement approx. W 1200 x H 2000 x D 2400 mm - Weight approx. 2500 kg
Key data: 750 kN, 150 mm
Control: STE 328-89-1 1/2" complete TOX Powerhouse: S75.160.200.12D Table size: 996 x 695 mm Installation height: 600 mm Total stroke: 150 mm Power stroke: 10 mm Weight: 5700 kg Electrical connection 230 V
Inv. číslo: 4465 Type: PL-140 LC Výrobce: OMC Vyrobeno: 2014 Parametry: Příkon: 75 kW
pressure: 180 tstroke: 400 mmcolumn daylight: 1500 mmFrame Width: 550 mmdistance spindle /table: max. 1000 mmtotal power requirement: 7,5 kWweight of the machine ca.: 2100 kgdimensions of the machine ca.: 2300x1200x2850 mmDomestic equipments:- Stable welded construction- Pressure cylinder laterally adjustable- Electric control via lever / manual over hand lever- Pressure gauge via pressure gauge- Material supports per cylinder in the height adjustable- CE markThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
pressure: 30 tstroke: 170 mmcolumn daylight: 600 mmFrame Width: 200 mmdistance spindle /table: max. 700 mmweight of the machine ca.: 200 kgDomestic equipments:- Stable welded construction- manually via hand lever- Pressure gauge via pressure gauge- CE markThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
echnical characteristics Nominal force, mc 1600 Not reach the slide to BDC, mm 12 Progress in the slide, mm 400 The frequency of continuous strokes, min-1 16 The highest frequency of single strokes, min-1 12 Closed height mm 870 Adjusting the closed height 220 mm Size slider, mm left to right 1600 front to back 1600 Dimensions plate, mm left to right 1600 front to back 1600 Power of main drive, kW 110 Dimensions, mm left to right 4670 aft 4670 height above floor level 8110 W 154 000kg
Inv. Num. : 6992 Type: LKT 250 Producer: METALPRESS Created: 1963 Parameters: Ram stroke: 120 mm Plunger adjustment: 100 mm Machine weight: 2700 kg
Key data: 400 t, 800 mm
Oil-hydraulic double-column press 400 T with sliding table Press type: Double column press Thermally neutral 80 – 120 °C Number of operating pages 1 page Forces Pressing force max. 4000 kN Free tear-off force max. 400 kN Print build-up time Closed tool steel on steel Max. 4 sec. Dimensions: 3,800 mm long and 4,475 mm wide Max. opening width 800mm Stroke 800mm Table height above floor 1100mm Height above ground (height) approx. 4300 mm Hall height min. 5500 mm Parallel deviation at 20°C +/- 0.1 mm Deflection Determined at max. clamping force with 70% occupancy < = 0.2 mm/m Weight Total weight of the press without consumables and table top approx. 28 tons Press table Table size 1500x1500 mm Velocities Quick closing at 100 mm sec. Pressing speed 8 – 3 mm sec. Acoustic pressure Sound pressure level, measured at a height of 1.5m on the control pane ...
Nominal force: 6300 ton Number of continuous strokes per minute: 40 Ram stroke: 460 mm Distance between ram and table (table is in upper position): 1150 mm Table adjustment: 15 mm Distance between press columns: 1950 mm Ram dimensions: -front to back: 1680 mm; -left to right: 1680 mm Table dimensions: -front to back: 1950 mm; -left to right: 1920 mm Mechanical upper ejector: -max stroke: 100 mm; -number of positions: 1 -steps of stroke adjustment: 25-30-75 mm -force: 30 ton Pneumatic lower ejector: -max stroke: 300 mm -stepless stroke adjustment: 15-300 mm -number of positions: 3; -force: 65 ton Side windows dimensions: -width: 1100 mm; -height: 1280 mm Main motor: 400/590 kW/rpm Press layout dimensions: 6300x8965 mm Total height: 11125 mm Height above floor level: 9150 mm Total weight: ...
2000 Ton Sumitomo Hot Forging Press line Year 2006 Stroke 350 mm (13.78") Strokes per min 75 Shut height 850 mm (33.47") SlideAdj. 7 mm (.27") Ram size 1200 mm LR X 1300 mm FB Bed size 1320 mm LR X 1300 mm FB 4 stage transfer system Slide knockout Bottom knockout Scrap System Dual Die Changer Extra Die Shoes Billet Heater and Billet Saw Also Available This line was used by HONDA to make transmission gears, It takes a billet, cuts it to size, heats it to 1300 C then the press hits it 4 times. It can determine good from bad parts, the bad parts get sent to a quench tank, the good parts get sent into a cool down conveyor that you can pick the parts up by hand at the end. The entire system was ran by one operator.
SPK KB 2132 eccentric press was manufactured in the USSR in 1980. Operating with a force of 160 tonnes, the press of almost indestructible design offers the highest quality and precision during the most demanding workpiece machining. The machine’s equipment includes among others a pneumatic clutch, a large-area slider performing up to 71 strokes per minute, central lubrication and manual control. The total weight of the press is 13200 kg. Technical data of the SPK KB 2132 press - maximum press force: 160 t - work table dimensions (L x W): 1000 x 700 mm - maximum slider stroke: 160 mm - minimum slider stroke: 25 mm - slider dimensions (L x W): 580 x 460 mm - slider adjustment range: 120 mm - slider stroke rate: 71/min - intermediate plate thickness: 110 mm - distance between work table and slider (slider in lower position, largest stroke, connector unscrewed): 480 mm - bore ...
