Manufacturer:
(Category: 106)
CONTROLS electronic controls SIEMENS S5 PRESS DESIGN drive system: hydraulic frame design: C-frame, single sided openings in uprights: yes table cushion: yes opening in table: yes PRESS FORCES total force (nominal): 100 toPRESS TABLE table surface (left-right): 710 mm table surface (front-back): 560 mmSLIDE slide force: 100 to table surface (left-right): 560 mm table surface (front-back): 450 mm spigot hole diameter: 50 mm stroke: 320 mm thickness of bolster plate: 150 mmSLIDE (HYDR. PRESS) approximation velocity max.: 340 mm/s working velocity max.: 32 mm/s return velocity max.: 330 mm/sSLIDE EJECTOR / CUSHION stroke: 40 mmDIE CUSHION (TABLE CUSHION) stroke: 80 mmTOO ...
CONTROLS PLC SIEMENS S5 95U PRESS DESIGN drive system: hydraulic openings in uprights: yes PRESS FORCES total force (nominal): 350 toPRESS TABLE table surface (left-right): 1600 mm table surface (front-back): 1400 mmSLIDE stroke: 1200 mmSLIDE (HYDR. PRESS) approximation velocity max.: 250 mm/s working velocity min.: 14 mm/s working velocity max.: 50 mm/sTOOL ASSEMBLY DIMENSIONS distance table - slide max.: 1250 mm distance between columns (H-frame): 1650 mm passline opening (free passage in side columns): 630 mmELECTRICAL SPECIFICATIONS total power consumption: 60 kWDIMENSIONS / WEIGHTS height above floor level: 4300 mm height under floor level: 1000 mm total weight approx.: 24000 kgATTACHMENTS (PRESSES ...
RÖCHER conversion 1991 (formerly SCHÖN) Pressure capacity 1,600 kN Plunger stroke160 mm Table dimensions 850 x 650 mm Light barrier control next due exam February 26 Tenon clamp lock in the ram Express lowering speed 274 mm/s Working speed 20/10 mm/s Return speed 273 mm/s Drive power 30 kW Operating voltage 380 volts/50 Hz Fuse max. 100 A
CONTROLS PLC SIEMENS S5 95U PRESS DESIGN drive system: hydraulic frame design: H-frame, monoblock openings in uprights: yes number of suspensions: 2 table cushion: yes PRESS FORCES total force (nominal): 650 toPRESS TABLE table surface (left-right): 3000 mm table surface (front-back): 1800 mmSLIDE slide force: 630 to table surface (left-right): 3000 mm table surface (front-back): 1800 mm stroke: 1000 mmSLIDE (HYDR. PRESS) approximation velocity max.: 200 mm/s working velocity min.: 7 mm/s working velocity max.: 15 mm/s return velocity max.: 120 mm/s return force: 65 toDIE CUSHION (TABLE CUSHION) cushion force: 250 to stroke: 400 mm cushion plate surface (l ...
Thermoforming press Jochnick & Norrmans 150/ton upper cylinder 100 Ton Lower Cylinder Table 1000x1000mm Built in 1973 New electrical cabinet in 1998 With light screen and wiring diagram Now in stock Price is freely loaded
- Minimum width 65 mm- Maximium width 185 mm- Load is 200 Metric Ton / Meter- Operation angle from 60 - 180 Gr- Die length 1000 mm and 500 mm sections
Segment radius top tooling for 1000 and 2000 Ton machineFull sets segmented on 835 mm and 10 sections to make 8000 mm- Radius 30 / Radius 31 / Radius 32 / Radius 33 / Radius 35- Radius 36 / Radius 39 / Radius 40 / Radius 41 / Radius 42- Radius 43 / Radius 45 / Radius 47 / Radius 48 / Radius 50- Radius 51 / Radius 53 / Radius 55 / Radius 57 / Radius 58- Radius 60 / Radius 62 / - Radius 70 / Radius 71 / Radius 73 / Radius 75 / Radius 80-
Press force: 1,250 tons. Clear width: 585 mm Installation height: max. 480 mm Piston stroke: max. 355 mm Weight: 7,200 kg.
Pressing force: max. 630 tons. Installation height: 375 mm Stroke: 275 mm Weight: 4,500 kg.
Air steam die forging hammer : Capacity : 16 tons, Nominal mass of drop parts : 16000 kg, Impact energy : 400 KJ, Ram stroke : 1500 mm, Ram stroke per minute : 20, Distance clear between guides : 1180 mm, Ram dimensions front to back : 1500 mm, Die holder dimensions front to back : 1600 mm, Bottom die impression to floor distance : 500 mm, Steam/air pressure : 0.7-0.9 MPa, Overal dimensions : - Floor space : 4500 x 2450 mm, - Height above floor level : 7920 mm, Mass of anvil block : 325 tons, Total weight of hammer : 425 tons.
pressure: 120 tchamfer lenght: 3050 mmdistance between columns: 2550 mmstroke of upper beam: 155 mmthroat: 350 mmajustment speed: 100 mm/secworking feed: 9.0 mm/secreturn speed: 77.0 mm/secControl: P 40 work height max.: 878 mmtable width: 104 mmoil volume: 150 ltotal power requirement: 11.0 kWweight: 7550 kgrange L-W-H: 3550 x 2150 x 2600 mmEquipment:- NC electro-hydraulic press brakes- with NEW ELGO NC control unit P40 New price approx. 4.000 Euro Control / movement of the backgauge - X axis (target/actual input) Control / movement of the depth setting - Y axes (target/actual input) Inching mode for X axis Y axes also possible- Swivel operation, front left- NC controlled axes : Y1 Y2 X- NC electro-motorized backgauge (X axis) with 2x manually adjustable stop fingers including lateral and height adjustment (Z R axis)- 1x branded set of upper tools (split)- 1x branded Multi-V bottom die ...
Qty. 1 Secon-hand aluminium extrusion press line Mfc.: AJAX, LOEWY Built: 1965 Force: 13.6 MN Billet dia.: 152 mm, 6 inch Length: 600 mm Scope of supply: Billet Induction Furnace Extrusion Press Exit profile flame cut Cable Puller Graphite Run-out Table with Pilgrims Pitch Traction bench Oliver Pendular cold saw Manual Piling
Qty. 1 Second-hand Complete Aluminium Extrusion Line Mfc.: SMS, Junker, Allen Bradley Force: 2500 MT Built: 1983 Modernised: 2017 Allen Bradley Ethernet Control System & NITROGEN DIE Cooling system Billet dia.: 8” Length: 450 – 950 mm Scope of supply: Log Loading Table Log Furnace Extrusion Press Run-out table Single Cable Puller Cooling Ventilator System Section Stretcher Storage Table Finishing Profile Saw Aging Furnace Die Heating Furnace Automatic Stacker Spare Parts
Qty. 1 Second-hand Complete Aluminium Extrusion Line Mfc.: CLECIM, AUBURTIN, OILGEAR Force: 3000 MT Bilet dia.: 8’’ Built: 1972 Modernised: Mechanical & Electrical in 2000 Scope of supply: Log Loading Table Log Furnace Billet Shear Extrusion Press Run-out Table Puller Stretcher Finishing Saw Aging Furnaces
pressure: 180 tchamfer lenght: 3100 mmdistance between columns: 2550 mmthroat: 310 mmstroke: 200 mmajustment speed: 80.0 mm/secworking feed: 10.0 mm/secreturn speed: 58.0 mm/secdayligth: 385 mmtable width: 240 mmwork height max.: 885 / 1050 mmoil volume: 180 ltr.total power requirement: 15.0 kWweight of the machine ca.: 9850 kg.range L-W-H: 4200 x 1750 x 2450 mm from a maintenance workshop well-maintained condition ()- in checked condition - machine video -https://www.youtube.com/watch?v=o_t9BBMsNNsEquipment:- simple, conventional electro-hydraulic press brake with torsion shaft for parallelism of the upper beam- electric back stop, with ball screws (X axis) with 4x manually adjustable stop fingers fine adjustment via handwheel at the front, with analog position display- electro-motor adjustment of the immersion depth (Y1 + Y2 axis) with digital position display- swiveling operation, mou ...
SLIDE total force (nominal): 250 to stroke: 61 mm stroke rate (max.): 60 /min stroke rate (min.): 15 /minCOUNTER RAM nominal force: 75 toV-RING nominal force: 75 toTOOL DIMENSIONS lower table (left-right): 540 mm lower table (front-back): 540 mm upper table (left-right): 540 mm upper table (front-back): 540 mmSTRIP-FEEDER sheet width max.: 250 mm sheet thickness max.: 10 mm sheet length min: 1500 mmDIMENSIONS / WEIGHTS space requirements -left/right-: 3150 mm space requirements -front/back-: 2120 mm total height: 3000 mm total weight approx.: 14000 kgLocated in Barcelona - SpainInstallation space of the toolsFront passage between the columns:Movable: 560 mmFixed: 560 mmSide passage between the columns:Mo ...
chamfer lenght: 650 mmplate thickness: -1.6 mmweight of the machine ca.: 150 kgdimensions of the machine ca.: 2000 x 1000 x 900 mmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Offer 25515 Specifications: - Max. working length 2050 mm - Column passage 1750 mm - Max. pressing force 850 kN - Distance table / plunger 535 mm - Stand projection 410 mm - Plunger stroke 365 mm - Lifting speeds - Rapid traverse downward speed 200 mm/sec - Upward speed 135 mm/sec - Downward pressing speed 1 - 11 mm/sec - Total drive power 13 kVA - Space requirement approx. W 2700 x H 2900 x D 2100 mm - Weight approx. 9100 kg - with: - with CNC control DELEM , DA - Two-hand control panel with foot switch - Controlled crowning device - Back gauge with height adjustment 5 - 860 mm - hydr. Tool clamping - Die table displacement pneumatically supported - Sharpening tool + V-die
Offer 25513 Specifications: - Max. working length 2050 mm - Column passage 1750 mm - Max. pressing force 850 kN - Distance table / plunger 535 mm - Stand projection 410 mm - Plunger stroke 365 mm - Lifting speeds - Rapid traverse downward speed 200 mm/sec - Upward speed 135 mm/sec - Downward pressing speed 1 - 11 mm/sec - Total drive power 13 kVA - Space requirement approx. W 2700 x H 2900 x D 2100 mm - Weight approx. 9100 kg - with: - with 5 axis CNC control DELEM , DA - Y1 + 2 ; X ; R ; Z - Two-hand control panel with foot switch - Controlled crowning device - Controlled backgauge with height adjustment 5 - 860 mm - hydr. Tool clamping - Die table displacement pneumatically supported
Offer 25514 Specifications: - Max. working length 3060 mm - Column passage 2690 mm - Max. pressing force 1300 kN - Max. distance table / plunger 535 mm - Stand projection 410 mm - Plunger stroke 215 mm - Lifting speeds - Downward speed idle max. 200 mm/sec - Upward speed 135 mm/sec - Downward pressing speed 1 to. 11 mm/sec - Total drive power 18 kW - Pneumatic connection 6 bar - Space requirement approx. W 3800 x H 2700 x D 2400 mm - Weight approx. 11500 kg - with: - with 6 axis CNC control DELEM - Two-hand control panel with foot switch - crowning device - Controlled backgauge with height adjustment 5 - 860 mm - hydr. Upper + Lower Tool Clamping - Die table displacement pneumatically supported
Key data: 40 t, 1030 mm
For sale is an automated press brake with 1st hand robot system for serial sheet metal part forming. Press brake 2019 BYSTRONIC Xpert 40/1030 Robot 2019 KUKA KR10R 1100 sixx Specifications Press brake - Press force: 400kN (40t) - Working length: 1030mm - Control: ByVision Robot - Max. nominal load capacity: 11kg - Reach: 1100mm - Axles: 6-axle - Position repeatability: 0.02mm - CE certified safety modules Characteristics - Fully automated bending cell with integrated 6-axis industrial robot - from 1st hand - Dimensions (LxWxH): approx. 3.25m x 2.8m x 2.5m - ByVision Bending control terminal with 22-inch Full HD touchscreen Machine condition - Operating hours: 7,724 h - Cycle counter: 310,212 - Complete service history, regular inspections - Technically perfect condition - Functional test: can be demonstrated during inspection - Location: Niederroh ...
CONTROLS PC controller BECKHOFF Offer for servicesof complete Overhaul of a Customer-Supplied Fineblanking Press FEINTOOL GKP 160Scope of Overhaul• Complete disassembly into individual components• Inspection of all parts, including crack testing of critical components• Overhaul of the drive system, new motors• Reworking and precise alignment of all guideways• Complete overhaul of the hydraulic cylinders• Overhaul of the clamping tables• Installation of a new hydraulic unit• Renewal of the pneumatic system• Renewal of the electrical systemModernisation / Retrofit• Combined table• Servo feed systems• Central lubrication system• RAZIOL band lubrication• New brake/clutch unit• BECKHOFF PC-based control system with touch panel• PILZ safety control system• Implementation of CE confo ...
CONTROLS electronic controls SIEMENS S7 300 PRESS DESIGN drive system: eccentric / crank openings in uprights: yes number of suspensions: 2 table cushion: no quick die change system: yes PRESS FORCES total force (nominal): 250 toPRESS TABLE table surface (left-right): 2000 mm table surface (front-back): 1100 mm height above floor level: 1105 mm opening in bed (left-right): 1700 mm opening in bed (front-back): 305 mmSLIDE table surface (left-right): 2080 mm table surface (front-back): 1000 mm stroke rate (max.): 120 /minSLIDE (MECHAN. PRESS) slide adjustment: 120 mm stroke adjustment: yes stroke min.: 20 mm stroke max.: 180 mmTOOL ASSEMBLY DIMENSIONS shut height (str ...
Specifications: Pressure: 50 t Bending length: 2000 mm Equipment: - Backgauge - Emergency stop push button - Foot control
An eccentric press / punching press year approx. 1992 is offered. Viewing is possible by arrangement.
An oil-hydraulic press brake built in 1978 is offered, max. pressing force: 2000kN, max. stroke: 250mm, max. operating pressure: 295bar. Control panel defective. Viewing is possible by arrangement.
CONTROLS PC controller BECKHOFF PRESS DESIGN drive system: knuckle-joint SLIDE total force (nominal): 160 to stroke: 60 mm stroke rate (max.): 70 /minCOUNTER RAM nominal force: 40 to stroke: 14 mmV-RING nominal force: 50 to stroke: 10 mmTOOL DIMENSIONS lower table (left-right): 480 mm lower table (front-back): 520 mm upper table (left-right): 480 mm upper table (front-back): 520 mm shut height max.: 314 mm ram adjustment: 80 mm distance between columns (H-frame): 500 mm passline opening (free passage in side columns): 220 mmSTRIP-FEEDER feeder type: roll feeder sheet width max.: 210 mm sheet thickness max.: 6 mm feeding step max.: 999.9 mm sheet len ...
CONTROLS PC controller BECKHOFF PRESS DESIGN drive system: servomechanic quick die change system: yes feedstock transport direction: left to right SLIDE total force (nominal): 250 to stroke: 70 mm stroke rate (max.): 140 /minCOUNTER RAM nominal force: 80 to stroke: 25 mmV-RING nominal force: 125 to stroke: 25 mmTOOL DIMENSIONS lower table (left-right): 600 mm lower table (front-back): 600 mm upper table (left-right): 600 mm upper table (front-back): 600 mm shut height max.: 386 mm ram adjustment: 125 mmCOIL CHAIR coil weight max.: 5 toDECOILER design: single reel sheet width max.: 500 mm coil weight max.: 5 toLEVELLER UNIT sheet width max.: 500 mm ...
