Manufacturer:
(Category: 106)
: neu : ca. 10 Wochen ab Auftrags : Türkei : 16100 €: 309.12 €: 100 to: fix : 300 mm: 680 mm: 1020 mm: 8 mm/s: 5 mm/s: 10 mm/s: 500x1020 mm: 100 mm: 190 mm: 2110 mm: 1000 mm: 2350 mm: 1985 kg2 guidingsupper plate with T-slotstable plate with T-Slotsmanometerrapid down move with automtic changeto working speedpiston stops in every position2 HAND CONTROL AND FOOT PEDALtable height adjustableaccording to CE regulationsuser manual in GERMAN and ENGLISHThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Manufacturer: Müller Stanz- und Umformtechnik GmbH & Co. KG Type: PMLE250x1700 R-HK Engine No.: A05036-02 Year of Make: 2006 Machine Type: Eccentric Press Press force: 2500 kN Press force: 250 t Stroke rate: 20–120 min⁻¹ Stroke: 25–125 mm Plunger adjustment: 100 mm Voltage: 400 V Motor power: 55 kW Connected load: 100 kW Weight: 47,000 kg Throw cushion: No Condition: Used Machine loses hydraulic oil Several leaks present in the hydraulic area Clamping pins for plunger adjustment deactivated due to hydraulic leaks Sale without conveyor system Videos available on request Location: Freiburg
Key data: 300 t
Manufacturer: Hylatechnik Paul Chrubasik GmbH Type: HSSP 300-3-XA4 Machine Type: Hydraulic Press Year of Make: 2000 Condition: used Press force: 3,000 kN Press force: 300 t Stroke: 300 mm Maximum installation height: 800 mm Table surface: 2,000 × 1,550 mm Plunger area: 2,000 × 1,540 mm Passage at the front: 2,000 mm Side passage: 1,050 mm Table height: 800 mm Fast forward: 340 mm/s Working speed 1: 32.5 mm/s Working speed 2: 19.5 mm/s Retraction: 340 mm/s Maximum working pressure: 280 bar Drive power: 75 kW Power supply: 400 V Frequency: 50 Hz Machine weight: approx. 38,500 kg Hydraulic oil tank: approx. 2,000 l Throw pillow: no Equipment: Complete DREHER conveyor system DREHER Belt Unwinder DREHER Belt Feed DREHER belt conveyor system Hydraulic cut impact damping with parallel hold Hydraulic Rolling Blocks Tool change consoles Siemens SIMATIC control ...
Offer 26226 Technical data: - Pressure capacity 220 t - Working width 3050 mm - Passage between the uprights 2550 mm - Table height 950 mm - Projection 450 mm - Installation height 550 mm - Drive 400 V / 18.5 kW - Floor recess - Space requirement approx. W 3500 x H 2950 x D 2000 mm - Weight machine approx. 17500 kg - Two-hand control panel with foot switch - Back gauge adjustable from the front by handwheel - Various bending tools
CONTROLS PLC PRESS DESIGN quick die change system: yes SLIDE total force (nominal): 630 to stroke: 125 mmV-RING nominal force: 320 toTOOL DIMENSIONS lower table (left-right): 800 mm lower table (front-back): 800 mm shut height max.: 420 mmSTRIP-FEEDER band lubrication system: yes ELECTRICAL SPECIFICATIONS mains voltage: 400 V mains frequency: 50 HzDIMENSIONS / WEIGHTS space requirements -left/right-: 6800 mm space requirements -front/back-: 3300 mm total height: 3730 mm height above floor level: 3005 mm height under floor level: 725 mm total weight approx.: 26000 kgATTACHMENTS -FINEBLANKING PRESS- autom. tool clamping device: yes light barrier: yes decoiler: yes leveller unit: yes Strip levelling machine SCHMID HR12H (YoM 1995)
CONTROLS electronic controls PRESS DESIGN drive system: hydraulic frame design: C-frame, single sided number of suspensions: 1 number of slide actions: 1 PRESS FORCES total force (nominal): 25 toPRESS TABLE table surface (left-right): 645 mm table surface (front-back): 535 mmSLIDE slide force: 25 to table surface (left-right): 500 mm table surface (front-back): 430 mm stroke: 400 mmSLIDE (HYDR. PRESS) return force: 4 toTOOL ASSEMBLY DIMENSIONS shut height (stroke down, adjustment up), BDC: 500 mmSTRIP-FEEDER feeder type: grip feeder sheet width max.: 76 mm sheet thickness max.: 3 mmELECTRICAL SPECIFICATIONS total power consumption: 7.5 kW mains voltage: 400 V mains frequency: 50 HzDIMENSIONS / WEIGHTS total weight approx.: 4000 kgMachine in like-new condition (lightly used)Optional with conveyor system and gripper feed:
: neu : 2025 : 080091 : prompt, Zwischenverkauf v : Türkei : 51120 €: 966.17 €: 1 : 60 to: 2550 mm: Y1 / Y2 und X Achse : 160 mm: 2150 mm: 250 mm: 350 mm: hydraulisch : 120 mm/s: 9 mm/s: 70 mm/s: 620 (mit optionaler R-Ach mm: 250 mm/s: 813 mm: 104 mm: 100 l: 5.5 kW: 3250 mm: 1200 mm: 2350 mm: 4250 kg3 axes (Y1, Y2, and X axis)CNC control DT-10- intuitive touch-screen control (simple drawing of the bending outline with your finger)- user friendly programming in dialogue form- automatic calculation of bending sequence- automatic calculation of the blank sheet size- graphic product and tool memory- correction possibility- USB interfaces for backup and programm transportation- PC software, generating programms on the PC and transfer to the machine by USBCNC controlled back gauge with linear guide and ball screw spindlesCNC controlled crowning tableintermediate clamps for upper toolupper ...
Press force: 200t, working length: 3550mm, distance between columns: 3050mm, length: 4000mm, width: 2000mm, height: 3000mm, weight: 16t. The machine is fully functional and in good technical condition. Upper tools are included. The lower tool, consisting of the die block or prism, is missing. An on-site inspection is possible.
Hydro-pneumatic corner jointing presses with support arms and new foot switches Profile height max. 140 mm Punching height max. 93 mm Punching stroke: 15 mm Press force 45 kN Weight approx. 280 kg
A transfer press line is offered, consisting of a Gräbener double-column transfer press including a feed unit and a Fecker decoiler-straightener combination with strip feed. 1) Gräbener GSET 2-250-280-315 double-column transfer press, year of manufacture: 1997, condition: operational, nominal force: 2500kN, nominal force stroke: 5mm, nominal energy capacity: 45kJ, slide stroke: 315mm, max. stroke rate: 50strokes/min, slide adjustment: 125mm, number of connecting rods: 2, shut height between bolster and slide: 800mm, bolster dimensions X/Y/Z: 2800mm/1150mm/200mm, slide area X/Y: 2800mm/900mm, max. die cushion stroke: 160mm, die cushion force: 88kN, machine dimensions X/Y/Z: approx. 5200mm/2700mm/5450mm, dimensions including sound enclosure X/Y/Z: approx. 7200mm/4700mm/5610mm, weight: approx. 55000kg. 2) Feed unit, condition: partially operational. 3) Fecker decoiler-straightener combina ...
: neu : ca. 4 Monate ab Auftragse : Italien : 63500 €: 1200.15 €: 70 to: 500 mm: 900x700 mm: 600 mm: 25 mm/s: 6 mm/s: 4 kW: 1140 mm: 940 mm: 2350 mm4-pillar guideram guide roundtable and ram with T-slots2 hand operationSiemens PLCmanometerusers manual Light barrier € on RequestSiemens touchscreen-control, 50 programsstoreable, for programming: • Upstroke and downstroke quota• Break time in the bottom• time of Decompression• setting pressure of work• Pieces counter• prestop in upstroke and downstroke• setting for movement in manual and in automatic• management of alarms and anomalies € on Request Working hour counter € on Request Stroke counter € on Request Decompression valve € on Request Oil cooler with decompreission valve € on Request Pressur switch € on RequestThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
: neu : ca. 14 - 16 Wochen ab Auf : Türkei : 83200 €: 1572.48 €: 130 to: 4.5 mm: 650 mm: 950 mm: 220 mm: 1 - 132 mm: 50 1/min: 6 : 95 mm: 70 mm: 325 mm: 500 mm: 11 kW: 1800 mm: 1725 mm: 3020 mm: 8000 kgWelded steel frame construction6-fold ram guidePneumatic clutch-brake combinationProtective enclosure with light barriers and side doorsMechanical overload protectionTwo-hand and foot pedal operationManual stroke adjustmentMotorized ram adjustmentVariable stroke rate via frequency converterOperating modes: Adjustment mode Two-hand release Foot release 2-stroke operation via light barriers Continuous operationTouchscreen for Stroke counter with preselection for continuous operation Stroke rate adjustment Lubrication intervals and duration Alarm messages Motor direction of rotation Monitoring of inputs and outputs2 free cams for connecting peripheralsAutomatic central lubrica ...
: neu : ca. 14 - 16 Wochen ab Auf : Türkei : 92600 €: 1750.14 €: 160 to: 6 mm: 750 mm: 1100 mm: 230 mm: 1 - 172 mm: 45 1/min: 6 : 100 mm: 80 mm: 375 mm: 540 mm: 11 kW: 1890 mm: 1950 mm: 3650 mm: 15500 kgWelded steel frame construction6-fold ram guidePneumatic clutch-brake combinationProtective enclosure with light barriers and side doorsMechanical overload protectionTwo-hand and foot pedal operationManual stroke adjustmentMotorized ram adjustmentVariable stroke rate via frequency converterOperating modes: Adjustment mode Two-hand release Foot release 2-stroke operation via light barriers Continuous operationTouchscreen for Stroke counter with preselection for continuous operation Stroke rate adjustment Lubrication intervals and duration Alarm messages Motor direction of rotation Monitoring of inputs and outputs2 free cams for connecting peripheralsAutomatic central lubric ...
: neu : ca. 4 Monate ab Auftragse : Italien : 89700 €: 1695.33 €: 85 to: 500 mm: 700x400 mm: 800x600 mm: 600 mm: 300 mm: 105 mm/s: 41 mm/s: 7 mm/s: 58 mm/s: 7.5 kW: 1200 mm: 1600 mm: 2500 mm4 guides for the slideT-slots in the tableRexroth hydraulic unitMonitored electrovalvesAir/oil heat exchangerPressure switchDouble pushbuttons controlStroke adjustment by limit switch micronsSiemens CPULateral fixed protrection gratesCE certification following ",IV enclosure",OPTIONS(prices on request):Blank holderPrismatic guidesFrontal light curtainCNC control Siemens with touchscreenHydraulic pump with variable flowProportional valvesLateral sliding guides with security micronsThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
: neu : ca. 6-8 Wochen ab Auftrag : Italien : 3800 €: 20 to: fix : 825 mm: 520 mm: 1150 mm: 500 mm: 1800 (PSS: 1950) mmThe table can be lifted manuallyHydraulic unit with motor and pumpAdjustable maximum pressureManometerEquipment compliant with CE regulations. Operating instructions in German and English.MODEL VERSIONS:PSS 20 TL: 1 speed 4 mm/s, single-hand control with lever € 3.800,00 PSS 20 L: 2 speeds 9 / 3 mm/s, single-hand control with lever € 4.500,00 PSS 20 NC: 2 speeds29 / 4 mm/s, two-hand control with lever and push button € 5.100,00 PSS 20: same as PSS 20 NC but with stroke 500 mm € 5.200,00The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
: neu : 2024 : 7321 : prompt, Zwischenverkauf v : Türkei : 12500 €: 216.96 €: 1 : 11300 €: 150 to: horizontal verschiebbar : 300 mm: 1570 mm: 280x200 mm: 5 mm/s: 10 mm/s: 2630 mm: 1000 mm: 2480 mm: 2100 kghorizontal adjustable cylinder with clamping leversteel welded framestop at any positionpressure manometersafety valve against overloading2 V-blockstable height adjustabletable up-down movement attachmentcontrol by operating leveraccording to CE regulations user manual in GERMAN and ENGLISHThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
: neu : ca. 12 Wochen ab Auftrags : Türkei : 41200 €: 786.92 €: 40 to: 1550 mm: X und Y Achse : 160 mm: 1260 mm: 320 mm: 380 mm: hydraulisch : 90 mm/s: 10 mm/s: 600 mm: 845 mm: 100 mm: 120 l: 5.5 kW: 2000 mm: 1600 mm: 2235 mm: 3450 kgNC control for immersion depth (Y) and back gauge (X)synchronization control by means of a torsion shaftsheet support armslight barriersintermediate pieces for the upper tool clampingdie seat and diedie seat with 4 V openingssplit upper tool, slightly cranked, dividedpedaluser manual in GERMAN or ENGLISHOPTIONAL EQUIPMENT (PRICES ON REQUEST):laser safety device FiesslerNC controlled R axismanual crowning tablemotorized crowning tableThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
: neu : ca. 4 Monate ab Auftragse : Italien : 38200 €: 729.62 €: 70 to: 500 mm: 700x350 mm: 700x500 mm: 500 mm: 250 mm: 24 mm/s: 5 mm/s: 4 kW: 1500 mm: 1000 mm: 2500 mm: 2100 kg2-fold round guidancetable and ram with T-slots2 hand operationSiemens PLCmanometerusers manual 4-fold round guidings € on Request Light barrier € on Request Siemens control for programming of stroke and press time € on RequestSiemens touchscreen-control, 50 programsstoreable, for programming:• Upstroke and downstroke quota• Break time in the bottom• time of Decompression• setting pressure of work• Pieces counter• prestop in upstroke and downstroke• setting for movement in manual and in automatic• management of alarms and anomalies € on Request Working hour counter € on Request Stroke counter € on Request Deompression valve € on Request Oil cooler with decompreission valve € on ...
CONTROLS electronic controls PRESS DESIGN drive system: hydraulic frame design: 4 column number of suspensions: 1 slide ejectors / cushion: yes table cushion: yes PRESS FORCES total force (nominal): 200 toPRESS TABLE table surface (left-right): 1330 mm table surface (front-back): 1150 mm height above floor level: 850 mm opening in bed (diameter): 250 mmSLIDE slide force: 200 to table surface (left-right): 1200 mm table surface (front-back): 1200 mm stroke: 800 mmSLIDE (HYDR. PRESS) approximation velocity max.: 300 mm/s working velocity min.: 30 mm/s return velocity max.: 400 mm/s return force: 200 toSLIDE EJECTOR / CUSHION working principle: hydraulical nominal force: 30 to stroke: 130 mmDIE CUSHION (TABLE CUSHION) cushion force: 30 to stroke: 850 mmELECTRICAL SPECIFICATIONS mains voltage: 400 V mains freq ...
: neu : ca. 12 Wochen ab Auftrags : Türkei : 18200 €: 349.44 €: 100 to: fix : 1500 mm: 300 mm: 1520 mm: 680 mm: 10 mm/s: 5 mm/s: 6 mm: 500x1520 mm: 100 mm: 190 mm: 2630 mm: 1000 mm: 2275 mm: 2500 kg2 guidingsbig upper tool holder and table with t-slotsupper and lower pressbrake toolmanometerrapid down move with automtic change to working speedpiston stops in every position2 hand operating panelTisch höhenverstellbaraccording to CE regulationsuser manual in GERMAN and ENGLISHThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Key data: 163 t
Hydraulic 4-column press – 163 T – 2,000 × 1,400 mm For sale is a hydraulic 4-column press from the manufacturer HYMAG with a maximum pressing force of 163 t. The machine has a table size of 2,000 × 1,400 mm, an open height of 1,300 mm and a stroke of 700 mm, making it suitable for forming, straightening, pressing, press-fitting and assembly work in industrial use. Technical data + information: Hydraulic 4-column press – 163 T – 2,000 × 1,400 mm General information - Manufacturer: HYMAG - Type: Hydraulic 4-column press - Model: HS 4 160-K3 - Machine number: 1606.18 - Year of construction: 2015 - Press force: 163 t - Nominal force: 1,600 kN - Table size (usable area): 2,000 × 1,400 mm - Plunger plate size: 2,000 × 1,400 mm - Table height: 800 mm - Open height: 1,300 mm - Stroke: 700 mm - Front passage: 2,010 mm - Side passage: 900 mm - Total height ...
A small Alfred Reith bench punch is available. Punching force: 50kN, max. round hole diameter: 60mm, max. square hole dimensions X/Y: 46mm/46mm, max. mild steel sheet thickness: 3mm, max. stainless steel sheet thickness: 2mm, max. aluminum thickness: 4mm, throat depth: 500mm, stroke: 66mm, weight: approx. 200kg. Documentation available. An on-site inspection is possible.
PRESS DESIGN drive system: eccentric / crank PRESS FORCES total force (nominal): 30 toPRESS TABLE table surface (left-right): 580 mm table surface (front-back): 360 mm thickness of bolster plate: 60 mm opening in bed (diameter): 110 mmSLIDE table surface (left-right): 350 mm table surface (front-back): 250 mm spigot hole diameter: 40 mmSLIDE (MECHAN. PRESS) slide adjustment: 60 mm stroke min.: 9 mm stroke max.: 76 mm stroke rate (max.): 140 /min main drive power: 2.2 kWTOOL ASSEMBLY DIMENSIONS distance table - slide max.: 214 mmELECTRICAL SPECIFICATIONS total power consumption: 2.25 kWDIMENSIONS / WEIGHTS space requirements -left/right-: 1.08 mm space requirements -front/back-: 1.05 mm total height: 2.1 mm total weight approx.: 1800 kgATTACHMENTS (PRESSES) 2-hand engagement: yes European CE standards: yes
: neu : ca. 14 - 16 Wochen ab Auf : Italien : 34500 €: 658.95 €: 100 to: fix : 835 mm: 500 mm: 780 mm: 1050 mm: 25 mm/s: 10 mm/s: 4 mm/s: 800 x 600 mm: 700 x 350 mm: 1800 mm: 1000 mm: 2400 mm: 2050 kgHydraulic multifunction workshop press for pressing and straightening and optional bendingVersion A (automatik): with 2-hand panel with limit micron switch for up/downstroke stop, automatic piston retraction, Siemens CPUVersion S (semiautomatik): 2-hand function by hand lever and pushbutton, limit micron switch for up/downstroke stopStandardmodel for pressing and straightening: table with t-sloats and straightening punchOPTIONS:Bending accessorie with tool holder, upper tool, dies with 4 slots and 2 frontal support armsMobile truck for quick assembly/disassembly of bending unitSiemens controlPressure switchHeat exchangerPiece counterTimerPlate supports for the rear sideSafety light guard ...
Key data: 250 t
Hydraulic press SCHULER Pressure 250 ton
Key data: 160 t, 1000 mm, 600 mm
STROKE 500 mm TABLE AREA 1000x850 DISTANCE BETWEEN COLUMN 1010mm DAYLIGHT 350 mm Approx speed 400 mm/s Motor: 40 kw
Key data: 250 t, 55 mm
Punching Press Minster Clutch Control Diameter 250 ton Stroke 55mm incl. Decoiler Perfecto type 28-12-7
Feindie Press Feintool Ostenwalder Cutting force 100 ton Total force 160ton Hydr. back pressure 0-40 yon Hydr. Hold-down 0-50 ton Stroke rate 18-72
: neu : 2023 : 7295 : ca. 12 Wochen ab Auftrags : Türkei : 22750 €: 436.8 €: 150 to: fix : 1520 mm: 300 mm: 1520 mm: 610 mm: 9 mm/s: 5 mm/s: 10 mm/s: 10 mm: 600x1520 mm: 100 mm: 190 mm: 2630 mm: 1000 mm: 2450 mm: 3270 kg2 guidingsbig upper tool holder and table with t-slotsupper and lower pressbrake toolmanometerrapid down move with automtic change to working speedpiston stops in every position2 hand panel and foot pedalTisch höhenverstellbaraccording to CE regulationsuser manual in GERMAN and ENGLISHThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
: neu : ca. 8 Wochen ab Auftragse : Italien : 11000 €: 211.2 €: 50 to: fix : 350 mm: 900 mm: 900 mm: max. 9 mm/s: 0,75 kW: 1700 mm: 700 mm: 2100 mm: 650 kgThe hydraulic movement of the piston is controlled by a handwheel,which enables very sensitive and precise positioning.One-handed operation is possible thanks to the working speed of less than 10 mm/s.Very suitable for straightening and pressing work.The cylinder can be moved sideway by handwheel (only ",M", versions)The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
