Manufacturer:
(Category: 106)
: 150 t: 3100 mm: 2600 mm: 400 mm: 270 mm: 800 mmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
CONTROLS conventional PRESS DESIGN drive system: eccentric / crank frame design: C-frame, single sided PRESS FORCES total force (nominal): 100 toSLIDE slide force: 100 to stroke rate (max.): 72 /minSLIDE (MECHAN. PRESS) slide adjustment: 80 mm stroke adjustment: yes stroke min.: 8 mm stroke max.: 112 mmTOOL ASSEMBLY DIMENSIONS shut height (stroke down, adjustment up), BDC: 407 mmATTACHMENTS (PRESSES) 2-hand engagement: yes for safe tools only
Inv. Num. : 8718 Type: LDC 250 Producer: SMERAL Created: 1987 Parameters: Compressive force: 245 t Maximum stroke rate upper table: 38 1/min Adjusting the ram: 120 mm Ram stroke: 200 mm Machine weight: 29800 kg
Description: Hydraulic single-column press with cycle feed Type: HEP 100 Specifications Electrical connection: 400 volts/50 Hz +/- 3 % Drive power: 5.5 kW Total power requirement: approx. 6.5 kW Control voltage: 24 volts/50 Hz +/- 3 % Hydr. Max. connection: 210 bar Set: 200 bar Performance data Ram speeds AB: approx. 48 mm/sec. at max. 100 kN compressive force Working speed AB reduced adjustable to: approx. 10 mm/sec. at max. 100 kN compressive force Ram speed ON approx. 96 mm/sec. at max. approx. 50 kN retraction force Plunger stroke: max. 200 mm Flow rate of the pump: approx. 15 l/min.
Single Column Press Dunkes TYPE: HZS 160 Specifications: Manufacturer: Dunkes Model: HZS 160 Operating hours: approx. 2250 The machine is in good condition and fully functional.
pressure: 150 tchamfer lenght: 4050 mmdistance between columns: 3550 mmControl: CYBELEC ModEva Pac throat: 350 mmdistance between table / ram: 430 mmtable width: 250 mmstroke: 250 mmtotal power requirement: 18,5 kWweight of the machine ca.: 16500 kgdimensions of the machine ca.: 4400x2100x3200 mmEquipment/accessories:- Control conversion at the end of 2018- Electric backgauge 1250 mm- 10-stage die displacement- crowning- EHT 26 mm tool holder- Axes controlled: Y1,Y2,X,R- Sheet metal holding table- 4x manually adjustable stop fingers- pneum. Upper tool clamping- Safety light curtain- 3x height-adjustable support arms- Oil cooler- 2-hand foot switchThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
pressure: 130 tno. of strokes: 50-250 Hub/minsheet width: 250mm mmstroke: 8-120 mmram - range of adjustment: 100 mmtable surface area: 1600x800 mmram surface: 1600x800 mmhole in the table: 1100x250 mmtable height: 1000 mm: 370 mmweight of the machine ca.: 24 tdimensions of the machine ca.: BxTxH 3900x2500x3800 mmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
pressure: 75 tstroke: 8-80 mmno. of strokes: 80-200 Hub/minram - range of adjustment: 70 mmtable surface area: 900x600 mmram surface: 900x470 mmhole in the table: 450x180 mmdist. between columns - front to rear: 500x350 mmdist. between pillars (front to rear): 788 mmtotal power requirement: 10 kWweight of the machine ca.: 10 tdimensions of the machine ca.: BxTxH 1600x1200x2800 mmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
pressure: 150 tthroat: 310 mmstroke: 30-120 mmno. of strokes: 20-60 Hub/minram - range of adjustment: 90 mmtable surface area: 820x600 mmram surface: 550x430 mmhole in the table: 330x200 mmtable height: 750 mmtool hole in ram: Ø50 mmweight of the machine ca.: 9,5 tdimensions of the machine ca.: BxTxH 2500x2500x3000 mmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
pressure: 35 tthroat: 240 mmstroke: 12-84 mmno. of strokes: 135 Hub/minram - range of adjustment: 70 mmtable surface area: 600x450 mmram surface: 360x180 mmhole in the table: 220x130 mmtable height: 630 mmtool hole in ram: Ø35 mmweight of the machine ca.: 2,5 tdimensions of the machine ca.: BxTxH 1500x2000x2600 mmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
pressure: 10 tstroke: 8-40 mmno. of strokes: 120-600 Hub/minram - range of adjustment: 40 mmtable surface area: 380x240 mmram surface: 220x140 mmhole in the table: 220x110 mmtable height: 910 mmtool hole in ram: Ø 30 mmthroat: 135 mmtotal power requirement: kWweight of the machine ca.: 1,2 tdimensions of the machine ca.: BxTxH 1000x1500x2000 mmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
pressure: 100 tthroat: 375 mmstroke: 20-125 mmno. of strokes: 60 Hub/minram - range of adjustment: 80 mmtable surface area: 920x660 mmram surface: 700x450 mmhole in the table: Ø90 mmtool hole in ram: Ø50 mmweight of the machine ca.: 8 tdimensions of the machine ca.: 2100x1500x3300 mThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
CONTROLS PLC SIEMENS S7 300 PRESS DESIGN drive system: hydraulic PRESS FORCES total force (nominal): 800 toPRESS TABLE table surface (left-right): 2600 mm table surface (front-back): 2000 mm height above floor level: 540 mmSLIDE stroke: 900 mmSLIDE (HYDR. PRESS) approximation velocity max.: 460 mm/s working velocity min.: 25 mm/s working velocity max.: 44 mm/s return velocity max.: 460 mm/sTOOL ASSEMBLY DIMENSIONS shut height (stroke down, adjustment up), BDC: 1700 mmELECTRICAL SPECIFICATIONS total power consumption: 180 kWDIMENSIONS / WEIGHTS total weight approx.: 95000 kgATTACHMENTS (PRESSES) press automation: yes gripper transfer system: yes acc. to actual accident protection regulation: yes & ...
pressure: 63 tthroat: 260 mmstroke: 8-100 mmram - range of adjustment: 63 mmno. of strokes: 115 Hub/min: 316 mmtable surface area: 630x490 mmram surface: 315x260 mmhole in the table: Ø 140 mmtotal power requirement: 4 kWweight of the machine ca.: 7,5 tdimensions of the machine ca.: 2000x2000x2700 mmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
A Durmazlar press brake distributed by Knuth is available. Pressing force: 35t, bending length: 1350mm, motor power: 5.5kW, stroke: 100mm, stroke rate: 17/min, max. operating pressure: 240bar, oil capacity: 150l. Machine dimensions X/Y/Z: approx. 1400mm/1400mm/2100mm, weight: approx. 1750kg, operating hours: 1258h. An on-site inspection is possible.
- Pressure capacity: 22 t - Projection: 175 mm - Stroke: 120 1/min - Plunger adjustment: 50 mm - Table height adjustment 50 mm - Stroke adjustment: 8-80 mm - Table: 520 x 400 mm - Plunger: 250 x 160 mm - Turnbuckle with trunnion clamping, D35 mm - Motor power 1.5 kW - Very smooth running - Mechanical disengagement of the rotary wedge coupling via pneumatic pneumatic cylinder - Pneumatic foot switch - No UVV - 4 pieces of machine feet - Connection cable CEE plug 16 A - Air connection with quick coupling - Weight: approx. 2,000 kg - Dimensions: Width 820 x Depth 1100 x Height 1800 mm
An old WMW single-column eccentric press is available. Pressing force: 25Mp, torque: 25kpm, shear area: 630mm², max. sheet thickness: 3.2mm, working capacity: 50kpm, pass-through sheet thickness: 1.6mm, working capacity: 25kpm, ram stroke: 5mm-60mm, max. table-to-ram distance: 400mm, stroke rate: 112 strokes/min, machine weight: approx. 1300kg. An on-site inspection is possible.
Capacity: 1600 tons Slide stroke: 300 mm Slide stroke length at maximum force: 0,16 mm Distance adjustment between tableand slider: 10 mm Slide stroke number in 1 min: 75 Length of a rod: 920 mm The closed height: 660 mm Table overall dimensions: 940x1200 mm Table height above floor level: 450 mm Slide overall dimensions: 860x910 mm The size of lateral windows: -Height: 560 E5931468 mm -Width: 600 mm Main motor: 110 kW Press overall dimensions: -Length: 5060 mm -Width: 3940 mm -Height above floor level: 5125 mm Press weight: 120 tons
Key data: 630 t, 275 mm
For sale is a used lowering press, manufacturer Sack + Kiesselbach, type EP 630. The machine is in very good condition. The press worked in an engraving company as a test press. Technical data: Pressing force: max. 630 tons. Installation height: max. 325 mm Stroke: max. 275 mm Weight: 4,000 kg
throat: 350 mmstroke: ca. 400 mmram diameter: 95 mmpress capacity: 25 ttable depth: 450 mmtable width: 1.500 mmtable height: 900 mmweight of the machine ca.: 2,5 tdimensions of the machine ca.: 2,0 x 2,0 x 2,3 mStraightening Press - Single ColumnMÜLLER - CR 25.2.1- Power-On Hours: 543h- incl. working lampThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Key data: 100 t
Sale due to switch to eccentric press Pressing force 100 tons Loading depth 360 mm Stroke 500 mm Daylight 800 mm Plunger area 530 x 400 mm Table height above floor 710 mm Working speed 10mm/sec Approach speed 150 mm/sec Return speed 150 mm/sec Required power 17 kW Dimensions L x W x H 1,400 x 2,000 x 3,200 mm Weight of the machine approx. 5.1 t Year of manufacture 2001 Price is net, VAT can be claimed. Loading facilities available All information without guarantee
gebr. Post-bending press Fabr. Graebener, Type GRNM, YOC 2005 max. bending force 16 t. Tool length 1,600 mm Adjustment of the underswing, hydraulic 2 cylinders Dimensions 5080 x 3290 x 2540 mm Kj Uovvlllerhyxkenb Weight 65 t.
PRESS DESIGN drive system: eccentric / crank PRESS FORCES total force (nominal): 80 toPRESS TABLE table surface (left-right): 850 mm table surface (front-back): 550 mmSLIDE table surface (left-right): 560 mm table surface (front-back): 376 mm spigot hole diameter: 50 mm stroke: 110 mm stroke rate (max.): 60 /minSLIDE (MECHAN. PRESS) slide adjustment: 80 mm stroke min.: 0 mm stroke max.: 110 mmTOOL ASSEMBLY DIMENSIONS shut height (stroke down, adjustment up), BDC: 360 mmDIMENSIONS / WEIGHTS space requirements -left/right-: 855 mm space requirements -front/back-: 1635 mm total height: 2640 mm total weight approx.: 5400 kgATTACHMENTS (PRESSES) 2-hand engagement: yes foot engagement: o ...
pressure: 110 tchamfer lenght: 3550 mmcolumn daylight: 3050 mmcolumn arm: 400 mmstroke of ram: 200 mmControl: Cybelec DNC 70 power capacity: 15 kWweight: 9500 kgThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
pressure: 125 tchamfer lenght: 4050 mmdistance between columns: 3700 mmControl: CybTouch 15 weight: 13.000 kgrange L-W-H: 5000 x 2700 x 2500 mmEquipment:- controlled axes: Y1, Y2, X, R, Z1, Z2, BH1, BH2- Lateral safety guards- Light barrier in front of the machine- Parking space for bending aids- foot switch- Protective grille behind the machine- Die displacement- Hydraulic upper and lower tool clamping- WEINBRENNER tool holder- hydr. crowningThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
An NDC hydraulic punch is available. Weight: approx. 1750kg. An on-site inspection is possible.
Pressing force: 4000kN, pressing pressure: 320bar, oil pressure: 250bar, blank holder force: 1600kN, blank holder stroke: 200mm, blank holder dimensions X/Y: 1000mm/800mm, blank holder ejector force: 160kN, ejector force: 63kN, ejector stroke: 100mm, overrun distance: 40mm, overrun time: 190ms. Documentation available. An on-site inspection is possible.
Punching force 45 t. 2 pcs. available from stock (Video under power on request)
- Rebuild in 2010 with SIEMENS TOUCH- Rebuild cost EUR 200.000- Distance measuring device with double taster- Big package with pressing tools in several diameters
VOLZ Werkzeugmaschinen GmbH & Co.KG
