used Hydraulic Double Column Presses for sale

pressure: 1600 tworking area: 140 - 520 mmpump pressure in use: 315 Bar number: 5 Pumpen FCS (Towler) : 650l/min bei 315 Bar forging speed: 1600T: max. 7 - 105 mm/s forging speed: 1200: max. 9,35 -140mm/s return speed: unbeladen: 370 mm/secfeed:: unbelastet: 380 mm/s max: Bewegungsabstand 1000 mmarm on rails: . tightening torque: 4mT weight max.: max. 3 t: geöffnet 1140 mmheight of clamping system above rail: max. 1250 inclination of clamping system above: 10° : +/- 150 mm working feed: 1000 mm/secclamping rotation per minute: 0 - 23 U/min. : The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Pressing force 160kN,pull cushion force 63kN,stoesselstroke 300 mm, pull-cushion stroke 150 mm, recessed height 500 mm, table 630x400,Stoessel 300x250,pull cushion flap 350x270,

a hydraulic four-column press Exner, type H4 SP 450, Y.O.M. 1983, pressure 450 to., side windows 475 mm. Installation height 600 mm, table area 1100 x 850 mm, impact area 300 mm, stroke 200 mm. Dimensions 3100mm x 2100 mm, depth 1,980 mm. Weight 13 to. ]

Here are the technical data of the offered machine: Technical data + information: • No-load speed up to 40 mm/sec • Opening speed up to 40 mm/sec • Starting press speed 5–15 mm/sec • Table size/heating plate size 600 × 600 mm • Plunger size/heating plate size 600 × 600 mm • 2 heating plates, electrically heated, up to 250 degrees – as OPTION • Total size approx. 2000 × 1000 × 2800 mm height • OIL temperature monitoring • Automatic lubrication • Free positioning of the plunger • SICK/LEUTZE light barriers 14.1 mm on the front • Circulating oil cooling • Pressure holding valve 0 to 1800 sec. • Rear monitored door • Pressure adjustment from 30 T to 120 T • Travel limitation either by pressure or position • Programming set-up mode, single stroke (adjustable via rotary switch) • Control panel permanently installed in the wall  ...

Double column press with 200 T output, Idle speed 45 mm/sec Opening speed 60 mm/sec Starting press speed 9 mm/sec Table size 2000x600mm Plunger size 2000x600mm OIL temperature monitoring Manual lubrication Free positioning of the plunger ( adjustable via adjustable sensors ) PILZ photoelectric sensors 14.1 mm on front and back Circulatory oil cooling Pressure retaining valve 0 to 600 sec. Mechanical plunger protection at the upper breakpoint T-grooves according to DIN, and according to customer requirements Pressure adjustment from 40 T to 200 T (adjustable via rotary knob) Travel limitation optionally via pressure or position Set-up operation, single stroke ( adjustable via key switch ) Two-hand operation Construction, commissioning, instruction against separate calculation Design Press design double column press Therma ...

Inv. Num. : 6701 Type: 4000 kN Producer: Hydraulico Created: 1977 Parameters: Control system: SIEMENS SIMATIC OP Compressive force: 4000 kN Stroke: 800 mm Table height: 680 mm

1 Hydraulic double-static press 400 to -refurbished new TOP ZUSTAND Manufacturer: INO Press - Press technology Waiblingen Model/Type 100 K-400 Built in 2000 Machine number 20445 The press has been put back to the original condition as good as new. We have got the press original, all wear parts have been renewed and checked. The press was cleaned 100% deep with dry steam cleaner and then repainted in original light grey. According to our opinion, the press has few hours of operation. The guides have been completely maintained and are in a new condition. The press was reset from its original use to its original condition. Depending on the customer's requirements, the press can also be used in the field of metal/non-metal for heated tools or composite/composite materials, i.e. cold or hot forming processes, warm-pressing, foaming, temperature control, etc. Mr. Eiblmeier  ...

Inv. Num. : 6700 Type: 3000 kN Producer: Loire Created: 1992 GO 2008 Parameters: Control system: SIEMENS SIMATIC OP17 Compressive force: 3000 kN Table length: 2495 mm Table width: 1505 mm Maximum distance between the table and the ram (when the ram is low): 1200 mm Stroke: 800 mm Working speed: 64 mm/s

Description: Distance between columns (length): 3200 mm Max. distance between table and ram: 2100 mm Ram surface: 2840x2100 mm Max. pressing force: 100 to, stroke: 1,500 mm, table surface area l x w : 3200x2100 mm, weight approx.: 50,000 kg, dimensions (l x w x h) approx.: 4,850 x 2,180 x 6,250 mm

Description: Press line consiting of, 6x MÜLLER Hydraulic double column deep draw presses Type: (2x) ZE 630 Year of manufacture: 1962 and 1963 Capacity: 630 ton Ram weight: 19.000 kg Max. punch weight: 47.000 kg Max. tool dimensions: 2460 x 1900 mm Min. installation height: 710 mm Max. installation height (only for cutting tool): 1060 mm Machine dimensions: approx. 4000 x , 2000 x 5500 mm Machine weight: approx. 150.000 kg  , Type: (4x) ZE 400 Year of manufacture: (2x)1971, 1965 and 1960 Capacity: 400 ton Ram weight: (3x) 12.000 kg and (1x) 8.200 kg Max. punch weight: 16.400 kg Max. tool dimensions: (3x) 2460 x 1400 mm and (1x) 2040 x 1300 mm Min. installation height: 610 mm Max. installation height (only for cutting tool): 910 mm Machine dimensions: approx. 4000 x , 2000 x 5000 mm Machine weight: approx. 120.000 kg 7x Pick- and Place robots Manufacturer: ABB Type: IRB ...

pressure: 100 tpassage width: . mmstroke: . mmtracking travel: 45 mmsafety distance: 208 mmtotal power requirement: kWweight of the machine ca.: tdimensions of the machine ca.: mThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

pressure: 630 KNdistance between columns: 800 mmstroke: 150 mmtable surface area: 720x550 mmram surface: 720x520 mmdayligth: 420 mmrapid drop speed: 394 mm/secworking feed: 71/17 mm/secreturn speed: 390 mm/secadjustment movement of the stroke: 120 mmtotal power requirement: 15 kWweight of the machine ca.: tdimensions of the machine ca.: mThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.