Manufacturer:
(Category: 106)
pressure: 2000 tdistance between columns: - mmstroke: 140 mmstrokes per minute: 15-50 H/mintable surface area: 1000 x 1100 mmdimension of ram: - mmweight of tools max.: - kgShut Height: 650 mmdistance table - lower edge of ram: - mmram adjustment: 25 mmmain drive: 30 kWtotal power requirement: - kWweight of the machine ca.: - tdimensions of the machine ca.: - mmProduction of stamped and formed parts, mechanical drive with toggle lever driveThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
pressure: 220 tchamfer lenght: 4100 mmdistance between columns: 3600 mmControl: Cybelec CybTouch 12 throat: 400 mmstroke: 220 mmdayligth: 480 mm: 140 mm/sbending speed: 0-10 mm/s: 110 mm/stotal power requirement: 18,5 kWdimensions: 4500x2000x2900 mmweight: 13.000 kgThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Offer 25461 Technical data: - Max. pressing force 30 t - Press pressure regulation - Stroke infinitely adjustable up to 200 mm - Lifting speed adjustable - Max. installation height 450 mm - Machine table with T slots W 800 x D 500 mm - Penetration between the columns 600 mm - Usable table surface W 800 x D 500 mm - Drive 400 V / 11 kW - Space requirement approx. W 1000 x H 2300 x D 1600 mm - Weight approx. 2500 kg
- Hydraulic clutch- CE-Safety 2e hand opperator system- Adjustable stroke / ram - Full set books / drawing / CE-Mark- Note in the Neck / Throath machine is repaired !- Only EUR 5500
- Hydraulic Clutch- CE-Safety 2e hand opperator system- Adjustable stroke / ram - Full set books / drawing / CE-Mark-
Qty.1 Second-hand deep drawing press Mfc.: LVD Co. Type: EMF-TWI- 200SP Built: 1982 Stopped production in 2002 Tested in 2012 In operation condition! Max. pressure: 200 T (2000 kN) Max. oil pressure: 300 bar Max. hydr. stroke: 2300 mm Max. distance table – ram: 4500 mm Motor power: 250 HP (187 kW) Table & ram dim.: dia. 300 mm Closing speed: 160/80 mm/sec. Working speed: 3507175 mm/sec. Cushion Max. capacity: 2 x 1000 kN Max. oil pressure: 300 bar Max. hydr. stroke: 2000 mm Table dim.: 1800 x 1800 mm Motor power: 75 HP (56 kW) Plate holder Plate holder dim.: 250 mm Plate holder stroke: 1000 mm Motor power: 25 HP (19 kW), 3 x220 V Weight: 75 Ton Pumps Main pump: 3 x A7V355LV 1RPFHO Pilot pump: Vickers V210-5-1A-10-5214 Tank Volume: 3350 L
PRESS DESIGN drive system: eccentric / crank table cushion: yes PRESS FORCES total force (nominal): 63 to nominal work capacity: 630 kNmPRESS TABLE table surface (left-right): 900 mm table surface (front-back): 560 mm opening in bed (diameter): 250 mmSLIDE table surface (left-right): 450 mm table surface (front-back): 310 mm clamping surface diameter: 50 mm stroke: 100 mm stroke rate (max.): 100 /minSLIDE (MECHAN. PRESS) slide adjustment: 80 mm stroke min.: 17.5 mm stroke max.: 100 mmDIE CUSHION (TABLE CUSHION) number of cushions: 1 TOOL ASSEMBLY DIMENSIONS shut height (stroke down, adjustment up), BDC: 340 mm distance table - slide max.: 440 mmELECTRICAL SPECIFICATIONS total powe ...
pressure: 160 tchamfer lenght: 3050 mmdistance between columns: 2550 mmstroke of upper beam: 175 mmdayligth: 240 mmthroat: 350 mmworking feed: 9.0 mm/secreturn speed: 86.0 mm/secwork height max.: ca. 920 mmControl: ERD 110 M oil volume: 150 ltotal power requirement: 15.0 kWweight: 9300 kgrange L-W-H: 4250 x 2170 x 2800 mmFeatures:- NC electro-hydraulic press brakes- with DURMA NC control ERD 110M Illuminated LCD display X-axis control & value display Y-axis control & value display- Swiveling operator panel, front left- NC controlled axes: Y1/Y2 + X- NC electro-motorized backgauge (X-axis) with 2x manually adjustable stop fingers including lateral and height adjustment (Z+R axes)- NC electro-motorized depth adjustment (Y-axis)- Manual bending table crowning Adjustment via hand crank with analog value display- AMADA/PROMECAM upper tool holder with upper wedge crowning & quick-change adapte ...
pressure: ca. 5 tdayligth: 110 mmthroat: 40 mmweight of the machine ca.: ca. 50 kgdimensions of the machine ca.: 1,2 x 0,5 x 1,3 mFunction: ready for operation: 6 t (estimaeted) hand-operated spindle press. The machine is professionally and durably lashed.Machine dealer with own stock of 1600 m².The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
pressure: 200 ttable length: 1600 mmtable width: 1300 mmdayligth: 1800 mmControl: Simatic ram return capacity: 6000 kgtable load capacity: 7000 kptotal power requirement: ? ca. 25-30 kWweight of the machine ca.: 19 tdimensions of the machine ca.: 2,95 5 6 mSpecial price 49,900 EUR from foundation upon acceptance until January 30, 2026. Normal price from warehouse.The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Key data: 200 t
Horizontal Hydr. Straightening and bending press, 200 tons, hand and foot control, hydraulics. 18kw, with bending tools.
Key data: 1 t, 110 mm
Hydraulic Fine Press, MATRA, , up to 1000kg, Table: 260x200mm, Radius 110, Foot or hand release, without UVV Fully functional, can be visited under power
Jessinegg + Urban, Stroke 300, Lift: 300, table 450x370, 1300kg
Key data: 170 t
Trumpf Press Brake Trumabend V170, 1700KN, Stroke: 365,. L-530cm, W- 240cm, H-300cm, Weight: 18to,
Key data: 25 t
Automatic straightener, shaft straightener , MAE -25RH, 1996, used Manufacturer: Maschinen- & Apparatebau Götzen GmbH, Germany Connected load: 14.5kva , Dim.: 2.5 x 1.5 x 1.8m, Weight : 5000kg
CONTROLS PC controller BECKHOFF PRESS DESIGN number of slide actions: 13 SLIDE slide force: 3 to stroke: 60 mm stroke rate (max.): 210 /minSLIDE (MECHAN. PRESS) slide adjustment: 6 mm variable speed: yes stroke rate (min.): 70 /min stroke rate (max.): 210 /min main drive power: 4 kWDIMENSIONS / WEIGHTS space requirements -left/right-: 2300 mm space requirements -front/back-: 1000 mm total height: 1900 mm total weight approx.: 4000 kg
A Beyeler press brake, today Bystronic, is available. Working length: 4100mm, press force: 2250kN, max. stroke: 400mm, throat depth: 250mm, installation height: 917mm, rapid traverse down/up: 150mm/s, working speed: 10mm/s, hydraulic pressure: 315bar, oil volume: 815l, max. oil temperature: 65°C, power: 30kW, max. upper tool weight: 400kg, max. workpiece weight: 13kg. Machine dimensions X/Y/Z: approx. 5500mm/2300mm/3350mm, weight: approx. 22000kg, operating hours: approx. 35000h. Including numerous upper tools, blades and lower tools. Documentation available. On-site inspection is possible.
pressure: 150 tstroke: 300 mmtable surface area: 1070 x 290 mmcolumn travel between the guideways: 1070 mmajustment speed: 9.0 mm/secworking feed: 5.0 mm/secreturn speed: 10.0 mm/secengine output: 11.0 kWweight of the machine ca.: 2070 kg.range L-W-H: 2200 x 1200 x 2550 mm Display machine from 2023 With only approximately 2 operating hours Like new condition Special price upon requestFurnishing:- Robust electro-hydraulic workshop press, with adjustable cylinder- Ideal for aligning axles, shafts, etc., but also for pressing in and out of bolts, bearings, bushings and much more.- Robust welded steel construction for high demands- Table height adjustment via piston rod including round steel chain and 2x locking bolts Piston rod with metric socket- 1x set of V-block prism supports- Manometer for pressure display- simply constructed hand control with: 1x delivery speed 1x working speed 1x re ...
pressure: 30.0 tstroke: 200 mmtable surface area: 775 x 190 mmcolumn travel between the guideways: 775 mmajustment speed: 7.5 mm/secworking feed: 5.0 mm/secreturn speed: 10.0 mm/secengine output: 3.0 kWweight of the machine ca.: 400 kg.dimensions of the machine ca.: 1.500 x 700 x 1.800 mmFeatures:- Robust electro-hydraulic workshop press with fixed cylinder- Ideal for aligning axles, shafts, etc.,. but also for pressing in and out bolts, bearings, bushings, and much more.- Robust welded steel construction for heavy-duty use- Table height adjustment via piston rod Includes round steel chain and 2 locking pins Piston rod with metric mount- 1 set of V-block prism supports- Pressure gauge for pressure display- Simple manual control with: 1 feed speed 1 working speed 1 retraction speed- Piston can be stopped in any position- Fixed hydraulic tank mounted on the side- Operating instructionsThe ...
pressure: 60.0 tstroke: 250 mmtable surface area: 1040 x 370 (315) mmcolumn travel between the guideways: 1040 mmajustment speed: 8.0 mm/secworking feed: 4.0 mm/secreturn speed: 10.0 mm/secengine output: 4.0 kWweight of the machine ca.: 800 kg.dimensions of the machine ca.: 1.700 x 700 x 2.100 mmFeatures:- Robust electro-hydraulic workshop press with fixed cylinder- Ideal for aligning axles, shafts, etc.,but also for pressing in and out bolts, bearings, bushings, and much more.- Robust welded steel construction for heavy-duty use- Table height adjustment via piston rod Includes round steel chain and 2 locking pins Piston rod with metric mount- 1 set of V-block prism supports- Pressure gauge for pressure display- Simple manual control with: 1 feed speed 1 working speed 1 retraction speed- Piston can be stopped in any position- Fixed hydraulic tank mounted on the side- Operating instructio ...
pressure: 100 tstroke: 300 mmtable surface area: 1070 x 315 mmcolumn travel between the guideways: 1070 mmajustment speed: 8.0 mm/secworking feed: 5.0 mm/secreturn speed: 10.0 mm/secoil volume: 90.0 lengine output: 5.5 kWweight of the machine ca.: 1870 kg.dimensions of the machine ca.: 2050 x 1000 x 2200 mmFurnishing:- Robust electro-hydraulic workshop press, with adjustable cylinder- Ideal for aligning axles, shafts, etc., but also for pressing in and out of bolts, bearings, bushings and much more.- Robust welded steel construction for high demands- Table height adjustment via piston rod including round steel chain and 2x locking bolts Piston rod with metric socket- 1x set of V-block prism supports- Manometer for pressure display- simply constructed hand control with: 1x delivery speed 1x working speed 1x retreat speed- Piston can be stopped in any position- Hydraulic tank mounted on t ...
CONTROLS PLC PRESS DESIGN drive system: hydraulic quick die change system: yes SLIDE total force (nominal): 450 to stroke: 230 mmSLIDE (HYDR. PRESS) working velocity min.: 5 mm/s working velocity max.: 70 mm/s return velocity max.: 200 mm/s return force: 200 toV-RING nominal force: 200 toTOOL DIMENSIONS lower table (left-right): 790 mm lower table (front-back): 760 mmOVERALL SPECIFICATIONS (COIL LINES) coil weight max.: 3 toCOIL CHAIR coil weight max.: 3 toSTRIP-FEEDER feeder type: roll feeder band lubrication system: yes ELECTRICAL SPECIFICATIONS total power consumption: 150 kW mains voltage: 400 V mains frequency: 50 HzDIMENSIONS / WEIGHTS total weight approx.: 28400 ...
Press brake Manufacturer: AMADA PROMECAM Type: HFB 125/40 Year of Make: 1991 Control: DELEM DA 58 Press force max:. 1,250 kg Stroke max.: 180 mm Sheet thickness 8 mm Working width/passage: 3.7 m Number of phases: 3 Power consumption: 11 kw Voltage/Frequency: 380/50 Rated current: 24 Weight: 9,900 kg Availability: immediately Reference Number: L2131
chamfer lenght: 0900 mmplate thickness: mmdistance between columns: 900 mmpressure: 20 tcolumn arm: 230 mmstroke length max.: 150 mmtravel -x axis: 350 mmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Hydraulic press JAM HYP-505H in very good condition for sale Manufacturer: JAM Model No.: HYP-505H Year of Make: 1990 Compressive force: 50 kN (5 t) Stroke length: 150 mm Working height: 385 mm Table size: 400 × 340 mm Punching hole: Ø 25 × 60 mm Ram speed: 260 mm/s Fpobmrjwin Emecu Idjb Ram speed: 39 mm/s Plunger return speed: 360 mm/s Pressure range: 7.7 MPa Safety light barriers Two-handed operation Voltage: 3-phase, 200 V, 1.5 kW, 10 A Weight: 400 kg Operating oil: 25 litres Height (mm): 1070 Width (mm): 670 Length (mm): 1060
Manufacturer: AIDA Type: NC1-45 Pressure: 45t Year of manufacture: 1987.08. Stroke length: 80mm Distance over table:: (adjustable) 240-300mm Table: 810x360 Plunger: 410x340 Electrical power: 3x200V(), 5.5kW - Japanese standard Net weight: 3300 kg Size: 980 x 1480 x 2275 mm
Manufacturer: AIDA Type: NC2-160 Thrust: 160t Year of construction: approx. 1991 Stroke length: 130 mm Distance above the table: (adjustable) 235–335 mm Table: 2030 x 600 mm Plunger: 1500x600mm Electrical power: 3x200V(), 15kW - Japanese standard Net weight: 19000 kg Size: 2140 x 2210 x 3175 mm Fobmeu D Ad Ejrcu Idepb Automatic lubrication system. Automatic Cutting Oil Dosing – RAZIOL EST-02 Optionally with disc winder and straightener.
CONTROLS PLC SIEMENS S7 PRESS DESIGN drive system: hydraulic quick die change system: yes feedstock transport direction: right to left SLIDE total force (nominal): 400 to stroke: 200 mmCOUNTER RAM nominal force: 100 to stroke: 30 mmV-RING nominal force: 200 to stroke: 30 mmTOOL DIMENSIONS lower table (left-right): 650 mm lower table (front-back): 650 mm shut height max.: 420 mm passline opening (free passage in side columns): 420 mmOVERALL SPECIFICATIONS (COIL LINES) sheet width max.: 500 mm sheet thickness max.: 12 mm feed velocity max.: 30 m/min feedstock transport direction: right to left LEVELLER UNIT sheet width max.: 500 mm sheet width (min): 60 mm shee ...
