subcategories
(3rd category level)
Manufacturer:
(Category: 103)
used
GeneralVertical Machining Center; Control: Control SIEMENS 828D CharacteristicsTable surface850 x 650 mmDimensions (L x W x H)3,07 x 2,67 x 2,84 mRapid feed X / Y / Z24/24/24 m/minMovement X / Y / Z550/550/510 mmSpindle taperSK 40 DIN 69871 Tool Magazine with24 PositionsMax. torque83 NmTorque (100% DC)57 NmDrive power (40% DC)13 kWDrive power (100% DC)9 kWSpeed max.12000 rpmWeight approx.5600 KgMechanical preparation for Oil-Mist Extractor UnitMechanical preparation for Oil-Mist Extractor Unit (opening diameter: D150 mm)SK40 interfaceTool clamping SK 40 for pull-studs DIN 69872Air coolant external and internalAir coolant external and internal (through spindle centre) switchable via M-FunctionElectronic HandwheelExternal electronic Handwheel
GeneralHSC-Precision Centre - Active chiller for main spindle and linear drives - Active chiller for electrical cabinet - Direct absolute measuring system with air purge - Coolant-airblast changeover - MPC (Machine Protection Control); Control: CELOS X with HEIDENHAIN TNC7 Technical DataSpindle taperHSK-E 50 Feed rate longitudinal/transverse/vertical1-80000/1-80000/1-80000 mm/minRapid traverse longitudinal/transverse/vertical80/80/80 m/minWorking area 1Longitudinal450 mmCross580 mmVertical460 mmTool changerApplicationVertical Type of magazineChain Type of gripperDouble gripper Number of tools60 Special equipmentFischer spindle 40,000 rpm with wave cooling 5-axis design Tool magazine 60 places HSK-E50 Production package high chip volume with IKZ (chip conveyor, rinsing gun, rotating viewing panel, AR flushing, IKZ 40 bar/600 1) Oil Mist Separator AFS BlowinSpecial equipmentPreparati ...
GeneralHorizontal 5-axis universal machining centre; Control: CELOS with Siemens 840D sl Operate Technical DataFeed rate longitudinal/transverse/vertical60000/60000/60000 mm/minRapid traverse longitudinal/transverse/vertical60/60/60 m/minWorking area 1Cross900 mmLongitudinal850 mmVertical1150 mmNC swivel rotary table integrated in rigid tableType of Measuring systemTable surface 1000 x 850 (Ø 850) mm5. Axes (swivelling range) +120 / -120 (AC) degree4. Axes (swivelling range) 360 x 0,001 degreeDistance between T-Slots 63 mmNumber of Slots 9Slot width 14 mmMaximum load (table centre) 1000 KgCentre bore 50 mmCabineFull protection cabinMotor spindle 20,000 rpmMotor spindle speedMASTER® HSK-A 63 Spindle speed 20 - 20,000 min-1 Output 35 kW / 25 kW (47 hp / 33 hp) Torque 130 Nm / 86 Nm (96 ft lbs / 63 ft lbs) (40 / 100 % duty cycle)Taper cleaning brushesTaper cleaning unit with rotating brus ...
GeneralUniversal turning-/milling center; Control: CELOS X with Siemens SINUMERIK ONE Working areaSwing diameter over guide ways580 mmTurning diameter550 mmMax. Turning Length1600 mmBar diameter max.104 mmWork spindle (left)Spindle bore118 mmSpindle diametre on front bearing160 mmMain drive 1Drive power (100% DC)32 kWDrive power (40% DC)36 kWSpeed range- 4000 rpmBench speed510 rpmTorque (100% DC)600 NmMax. torque (40% DC)720 NmTurning-milling spindleSpindle taperHSK-T 63 Spindle speed-12000 rpmDrive power (100% DC)8,8 kWDrive power (40% DC)10,5 kWTorque (100% DC)73 NmTorque (40% DC)90 Nmlocking moment800 NmSwivelling range+/- 120 degreeTool magazineType of magazineChain Number of tools30 Max. tool diameter78 mmMax. tool-Ø with free adjacent pockets130 mmCounter spindle ISM 102, A2-8Counter spindle as integrated spindle motor, ISM 102, A2-8 - Drive power 32/36 kW (S1-100%ED / S3-40%ED ...
x-travel: 1120 mmy-travel: 350 mmz-travel: 400 mmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Key data: 1600 mm, 800 mm
CNC bed milling machine with Heidenhain control 415, good condition, hydraulic tool clamping, coolant device, central lubrication, lighting,.. Travel X1600/y800/z650/ Spindle holder SK 50 Spin elder speed 60-1800rpm Working feed rate 10-3000mm/min Rapid traverse 10m/min Table clamping surface 1800x610mm Machine weight 9500kg Table load 3000kg
CNC milling machine, cover FP3A, spare parts machine, control defective / incomplete We sell parts. of this machine, SK40 milling head, with quill, tool changer, ... Control unit, table, spindles, motors, spindle nuts, ... Or total: Euro 1800,- ex works
Tool milling machine Maho, 700C Control : Maho 432, Year of construction 1989, Mounting SK40, Process : X-700, Y-450, Z-500, quill Machine can no longer be viewed under power. Has lost parameters! Would also sell spare parts, table, milling head, drives, control, ...
Tool milling machine Maho, 700C Control : Maho 432, Year of construction 1989, Mounting SK40, Process : X-700, Y-450, Z-500, quill Machine can no longer be viewed under power. Has lost parameters! Would also sell spare parts, table, milling head, drives, control, ...
PFAUTER P630 Gear Hobbing Machine.Chip ConveyorMaximum Gear Diameter 630 mmGear Width 425 mmMaximum Module 10Table Diameter 550 mmTable Bore 125 mmMaximum Cutter Length 215 mmMinimum Number of Teeth 8Maximum Workpiece Length 825 mmDistance Milling Spindle - Clamping Surface 50 - 425 degreesMilling Slide Swivel 240 degreesSpindle Speeds 62 - 390 RPMTangential Adjustment 200 mmAxial Feeds 0.4 - 6.8 mm/revRadial Feeds 0.1 - 1.7 mm/revMaximum Cutter Diameter 192 mmTotal Power Requirement 20 kWChange Gears Set / Chip Conveyor / Coolant Tank
external diameter: - mmbore diameter in mm: - mmwidth: - mmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
4 Spindle High Speed Train Milling Machine, ANGER, HCP 10/5, 2005 Control : NUM, very few operating hours. Methods: X-300, Y-1130, Z-300, 4-axis +/- 180 degrees 4 high frequency spindles : Precise 60000 / 160000 / 18000 / 16000 rpm , rpm Tool holder : Collets depending on the spindle Chip conveyor, ATC, recooling unit, external measuring system Renishaw Power consumption 41 kw
4 Spindle High Speed Train Milling Machine, ANGER, HCP 10/5, 2005 Control : NUM, very few operating hours. Methods: X-300, Y-1130, Z-300, 4-axis +/- 180 degrees 4 high frequency spindles : Precise 60000 / 160000 / 18000 / 16000 rpm , rpm Tool holder : Collets depending on the spindle Chip conveyor, ATC, recooling unit, external measuring system Renishaw Power consumption 41 kw
Lg.Nr. 26305 Technical data: - Operation via two-hand lever - Material clamping by pneumatic clamping cylinder - Workpiece width / clamping range W 115 x D 100 mm - Milling area at the top after stop / copy template. W 340 x D 100 mm - Stroke at the top T 110 mm - Milling area at the bottom after stop / copy template. W 240 x 90 mm - Stroke bottom front / rear 95 / 45 mm - Spindle speed 12000 rpm - Dosing spray device - Air consumption per work cycle - without spraying 12 ltr - with spraying 24 ltr - Left + right original material support - Drive 400 V / 0.75 kW - Space requirement approx. W 900 x H 1400 x D 1250 mm - Weight approx. 300 kg
This 3-axis MORI SEIKI DURA VERTICAL 5060 was manufactured in 2007. It features a travel distance of 600 mm in the X-axis, 530 mm in the Y-axis, and 510 mm in the Z-axis. The machine includes a table size of 900 x 600 mm and a maximum table load of 500 kg. If you are looking to get high-quality machining capabilities, consider the MORI SEIKI DURA VERTICAL 5060 vertical machining centre we have for sale. Contact us for further details.
This 5-axis DOOSAN VCF850 was manufactured in 2018. It features a substantial X-axis travel of 3500 mm, Y-axis travel of 950 mm, and Z-axis travel of 800 mm. The machine operates at a maximum rotational speed of 12000 rpm and includes a BT40 tool holder type. If you are looking to get high-quality milling capabilities, consider the DOOSAN VCF850 vertical machining center we have for sale. Contact us for further details.
This 3-axis Quaser MV184P/12B was manufactured in 2015. It features a travel distance of 1020 mm on the X-axis, 610 mm on the Y-axis, and 610 mm on the Z-axis. The machine is equipped with a Siemens 828D controller and has a maximum rotational speed of 12000 rpm. If you are looking to get high-quality machining capabilities, consider the Quaser MV184P/12B vertical machining centre we have for sale. Contact us for further details.
This 4-axis Mazak HCN-5000 was manufactured in 2024. It features an X-axis travel of 730 mm, Y-axis travel of 730 mm, and Z-axis travel of 800 mm. The machine has a maximum workpiece weight of 700 kg and a spindle speed of 18,000 RPM. If you are looking to get high-quality machining capabilities, consider the Mazak HCN-5000 horizontal machining centre we have for sale. Contact us for further details.
This 3-axis KUNZMANN WF 4/3 was manufactured in 1998. It features a travel of 400 mm in the X, Y, and Z axes, with a table size of 650 x 350 mm and a maximum table load of 250 kg. The spindle speed reaches up to 2,500 rpm, providing efficient machining capabilities. If you are looking to get high-quality vertical machining capabilities, consider the KUNZMANN WF 4/3 vertical machining centre we have for sale. Contact us for further details.
This 3-axis Matsuura Vplus 1000/40 was manufactured in 2005. It features a travel range of 1020 mm in the X-axis, 550 mm in the Y-axis, and 500 mm in the Z-axis. The machine includes a table size of 1150 x 550 mm and a maximum table load of 500 kg. If you are looking to get high-quality machining capabilities, consider the Matsuura Vplus 1000/40 vertical machining centre we have for sale. Contact us for further details.
This 3-axis YCM NSV 156 A was manufactured in 2013. It features a travel distance of 1530 mm in the X-axis, 650 mm in the Y-axis, and 610 mm in the Z-axis. The machine includes a robust table size of 1630 x 650 mm and a maximum table load of 1500 kg. If you are looking to get high-quality machining capabilities, consider the YCM NSV 156 A vertical machining centre we have for sale. Contact us for further details.
This 4-axis Matsuura H. Plus 405 was manufactured in 2006. It features an X-axis travel of 600 mm, Y-axis travel of 660 mm, and Z-axis travel of 660 mm, along with a 360° rotary B-axis. The machine has a maximum workpiece size of 700 × 850 mm and a tool changer capacity of 60 tools. If you are looking to get high-quality machining capabilities, consider the Matsuura H. Plus 405 horizontal machining centre we have for sale. Contact us for further details.
x-travel: 3500 mmy-travel: 1000 mmz-travel: 900 mmControl: Heidenhain iTNC 530 total power requirement: kWweight of the machine ca.: 21 tdimensions of the machine ca.: 10770 x 4100 x 3150 mControl system: Heidenhain iTNC 530Operating hours: 54631 hX-axis 3500 mmY-axis 1000 mmZ-axis 900 mmDrive power 30 kWSpeed range 20–3800 rpmRapid traverse 15 m/minFeed rate 4 m/minClamping surface 2x 1600 x 960 mmMax. table load 2 x 4000 kgMachine weight (approx.) 21 tMachine dimensions (WxDxH) 10770 x 4100 x 3150 mmTechnical data / AccessoriesUniversal bed-type milling and boring machineMilling head position: Vertical, horizontal (top, center, left, right)Heidenhain TS 120 3D touch probeKekeisen TW 32 drum-type tool changerKnoll hinged-belt chip conveyorThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
This 3-axis Hurco VMX42t was manufactured in 2007. It features an X-axis travel of 1067 mm, Y-axis travel of 610 mm, and Z-axis travel of 610 mm. The machine includes a table size of 1270 x 610 mm and a spindle speed of 12,000 rpm. If you are looking to get high-quality machining capabilities, consider the Hurco VMX42t vertical machining centre we have for sale. Contact us for further details.
