Manufacturer:
(Category: 106)
pressure: 230 tchamfer lenght: 3060 mmdistance between columns: 2690 mmStroke: 365 mmControl: DELEM DA 65 throat: 410 mmdayligth: 535 mmdimensions: 3660 x 2310 x 3100 mmmachine weight ab.: 17.700 kgThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
: neu : 2026 : 070223 : September 2026, Zwischenv : Türkei : 20100 €: 385.92 €: 10 to: 1.4 mm: 270 mm: 370 mm: 100 mm: 1 - 40 mm: 200 1/min: 4 : 35 mm: 25 mm: 160 mm: 180 mm: 0.75 kW: 1170 mm: 1180 mm: 1700 mm: 590 kgWelded steel frame construction4-fold ram guidePneumatic clutch-brake combinationProtective enclosure with light barriers and side doorsTwo-hand and foot pedal operationManual stroke adjustmentManual ram adjustmentVariable stroke rate via frequency converterOperating modes: Adjustment mode Two-hand release Foot release 2-stroke operation via light barriers Continuous operationTouchscreen for Stroke counter with preselection for continuous operation Stroke rate adjustment Lubrication intervals and duration Alarm messages Motor direction of rotation Monitoring of inputs and outputs2 free cams for connecting peripheralsAutomatic central lubricationEquipment in a ...
Key data: 100 t, 400 mm
Press force 1000 kN Stroke 400 mm Clear dimension 600 mm Installation height max./min. 590 / 210 mm Closing speed 100 mm/s Working speed 10 mm/s Retraction speed 160 mm/s Drive power 15 Kw Table area 800 x 500 mm Plunger area 800 x 500 mm Cushion force 300 kN Cushion stroke 150 mm Cushion speed 30 mm/s Machine dimensions 1600 x 1700 x 2930 mm Machine weight approx. 5500 kg SIEMENS safety controller Input of part data such as speed, pressing force, etc. via 12" touch panel Stepless switching from rapid to working speed Stepless programming of the pressing force 15 - 100% Integrated tool management for 5000 tools Safety two-hand transmission mounted on stand Sliding side doors Light barriers installed in the side doors Control cabinet with control on the stand Operating modes: Set-up operation Single stroke with protection functionality Single stroke in 1-str ...
Offer 26175 Technical data: - Max. pressure capacity up to 25 t - Max. plunger stroke 160 mm - Installation height without straightening unit 675 mm - Projection to the middle of the ram 250 mm - Table size approx. 1300 x 300 mm - Working speed AB approx. to max. 30 mm/s - Working speed to approx. 100 mm/s - Oil filling quantity approx. 150 ltr - Drive 400 V / 10 kW - Space requirement approx. W 4900 x H 2400 x D 1500 mm - Weight approx. 3000 kg - with: - Straightening table extension 2030 + 1520 mm - Transfer carriage with mounts on straightening table - Lace intake - Roll recording - Directional stamp - Swivel switch with dial gauge
press capacity: 14,5 MNoperating pressure: 310 barstroke of press: 960 mmspeed: Press: max. 23 mm/sspeed: Press: nom. 17 mm/sExtrusion PressSMS - HyBrEx 14- Extrusion centerline above pass line: 1.000 mm- Extrusion height above pass line: 3.400 mmBILLET CONTAINER- Contact force: 1.4 MN- Retraction force: 1.0 MN- Retraction stroke: 1,155 mm- Bore diameter: 160 mm- Container length: 830 mm- Billet length, min. - max.: 250–800 mm- Shortest billet length (with billet shearing): 200 mmSHEARS- Shear, cutting force: 0.4 MN- Profile shear – tool slide, cutting force: 0.2 MNPROFILE CIRCLE / TOOL ASSEMBLY- Die backer opening – diameter: 190 mm- Die backer opening – width: 230 mm- Tool assembly – diameter: 330 / 277.5 mm- Tool assembly – height: 380 mmHYDRAULIC SYSTEMFour high-pressure oil pumps- Max. operating pressure: 310 bar- Drive power: 75 kWHigh-pressure variable-displacement pum ...
Key data: 200 t
Press brake – 200 T – Open width 1,600 mm For sale is a hydraulic press brake from the manufacturer DURENDUS with a maximum press force of 200 t. The machine has an open width of 1,600 mm, a maximum installation height of 1,200 mm and a stroke of 1,000 mm, making it suitable for bending, forming and straightening work in industrial use. Technical data + information: Press brake – 200 T – Open width 1,600 mm General information - Reference ID: ME-2026-A-180_DE-2026-ME-215-01 - Type: 2-column frame press - Manufacturer: DURENDUS - Press force: 200 T (adjustable) - Open width: 1,600 mm - Open height: 1,200 mm - Usable area ram: 1,500 mm - Table height from the floor: 850 mm - Overall dimensions (W × D × H): approx. 1,300 × 2,700 × 3,900 mm - Total weight: approx. 5,300 kg Hydraulic cylinders - Stroke: 0–1,000 mm - Working pressure: 270 bar - Cylin ...
Machine number: 473678Delay time: 69 msSafety distance for hand control tool: 110 mmTable dimensions: 700 x 525 mmReference: Walter - Lot 17 Auction-ID: A7-48268-7
Machine number: 2810292Operating voltage: 380 VConnection: 1.5 kWMax. pressing force: 250 kNThroat: 190 mmPlunger strokes: 120/minPlunger adjustable: 5 mmStroke adjustable: 4 - 60 mmTable dimensions: 550 x 430 mmincl. straightening device from the manufacturer REBENDERReference: Walter - Lot 156 Auction-ID: A7-48268-19
The dimensions of the machine are LxWxH 2500mm x 1600mm x 2500mm. The weight is 8250kg. The machine is in a little-used condition.
: neu : ca. 14 - 16 Wochen ab Auf : Türkei : 202100 €: 3869.08 €: 320 to: 6050 mm: Y1 / Y2 / X und R Achse : 365 mm: 5100 mm: 450 mm: 630 mm: hydraulisch : 160 mm/s: 10 mm/s: 160 mm/s: 650 mm: 500 mm/s: 250 mm: 1100 mm: 154 mm: 160 l: 7500 mm: 1910 mm: 3350 mm: 29000 kg1 SERVO MOTOR AND PUMP PER CYLINDER4 axes (Y1, Y2,X andR)CNC control SKY 22- intuitive touch-screen control (simple drawing of the bending outline with your finger) 21,5 in full HD- with 2D and 3D working screen- direct programming of the bending angle- user friendly programming in dialogue form optionally in 2D or 3D mode- 2D and 3D simulation of the bending sequence- automatic tool selection in 3D mode- automatic calculation of the blank sheet size- bending order calculation- graphic product and tool memory- correction possibility- USB and Ethernet interfaces for import, backup and programm transportation- OS: Windo ...
CONTROLS conventional PRESS FORCES total force (nominal): 100 toSLIDE stroke rate (max.): 55 /minSLIDE (MECHAN. PRESS) slide adjustment: 80 mm stroke min.: 10 mm stroke max.: 120 mmDIMENSIONS / WEIGHTS total weight approx.: 4800 kg
full function, can be programming for robot, etc. Press capacity: max. 45 t Pull force: max. 45 t Counter force in pressing position: max. 17 t Stroke of the punch: 175 mm Filling height: max. 140 mm Deduction: max. 85 mm Compression distance: max. 55 mm Top pressing: max. 15 mm Stroke rate: 9 – 26 min.-1 Motor: 7,4 kW Approx: 3000x1200x1800 mm Net weight: about 6000 kg
pressure: 135 tchamfer lenght: 4100 mmdistance between columns: 3600 mmControl: DELEM feed down: 100 mm/secfeed bending: 10 mm/sectotal power requirement: 15 kWweight of the machine ca.: 11.700 kgThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
A CNC press brake Amada is available. Press force: 170t, bending length: 3170mm, bending length: 3100mm, frame distance: 2700mm, throat depth: 420mm, stroke: 350mm, installation height: 620mm, table width: 180mm, working height: 960mm, backgauge X: 600mm, repeatability Y: +/-0.01mm. Machine dimensions X/Y/Z: approx. 4550mm/2650mm/3150mm, weight: approx. 12700kg, control system: Amada, operating hours: 51039h. Without a bending tools. Documentation available. An on-site inspection is possible.
A CNC press brake Amada is available. Press force: 800kN, bending length: 2500mm, press beam length: 2570mm, distance between uprights: 2125mm, throat depth: 420mm, max. stroke: 350mm, installation height: 620mm, table width: 60mm, table height: 960mm. Machine dimensions X/Y/Z: approx. 3300mm/1600mm/2750mm, weight: approx. 6100kg, control system: Amada. Documentation available. An on-site inspection is possible.
pressure: 250 tdistance between columns: 1350 mmstroke: 400 mmdayligth: 600 mmTable dimensions: 1250x800 mm: 640 mmtable height: 800 mmweight of the machine ca.: 36.000 kgdimensions of the machine ca.: 3600x2800x5700 mmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
High: 2.100 mm, Long: 1.200 mm, Force: 20 TN, Width: 1.300 mm, Voltage: 220/380 V, Neckline: 160 mm, Lower speed: 18 mm / s, Stem travel: 100 mm, Total power: 5.5 CV, Rate of climb: 27 mm / s, Maximum aperture: 650 mm, Piston rod ø of: 100 mm, Surface of the table: 1050 x 360 mm, Specification: Hydraulics
NC HYDRAULIC SIMPLE PRESS BRAKE NOMINAL FORCE: 3000KN WORKTABLE LENGTH: 5000MM POLES DISTANCE: 3800MM THROAT DEPTH: 400MM STROKE: 300MM MAX OPEN: 600MM POWER: 45KW DIMENSION: 5000MM(L) X 2500MM(W) X 3200MM(L) LOCATION: F39, TGE KINDLY CONTACT: syweetopglove.com.my
Millutensil BV 30 ERGYear of manuf. : 2022 Control : Siemens Simantic HMI ____________Description:In Generel:Table dimensions:1,500 x 1,000 mmMax. clamping force:500 kNMax. load capacity top plate:2,500 kgMax. load capacity under plate:7,000 kgRG version:plate can be pulled out and tilted:
PRESS DESIGN quick die change system: yes SLIDE total force (nominal): 100 to stroke: 20 mm stroke rate (max.): 80 /minTOOL DIMENSIONS lower table (left-right): 430 mm shut height max.: 220 mmApprox. 79 million strokes
Metal press manufactured in 1959. This Müller SE 201.1.1 /32 features a T-slotted table and includes a optional hydraulic unit. The machine is in production environment and is used. If you are looking to get high-quality metal pressing capabilities, consider the Müller SE 201.1.1 /32 machine we have for sale. Contact us for further details.
Qty. 1 Second-hand Aluminium Extrusion Press Line Mfc.: Youngstown USA Force: 1650 MT Billet dia.: 6”, 152 mm Built: early 1980s, completely Revamped in 1999 Production start: 1999 Stopped: 2025, but still under power Billet size: 6”, 152 x 550 mm Press Type: Horizontal Hydraulic, Direct Extrusion PLC: LS XGK (Korea) Required floor space: 20 mtrs x 60 mtrs
max. wheel diameter: 450 mmmax. module: 4 mminternal dia. - min.: 100 mminternal dia. - max.: 300 mmMaximum permissible peeling wheel diameter: 175 mmDiameter of the installation area: 125 mmslide travel X-axis: 350 mmslide travel Z-axis: 300 mmslide travel Z-axis: 440 mmLargest swivel range of the peeling head: ±25 Gradworkpiece table outer diameter: 570 mmWorkpiece table – Maximum permissible load: 5 kNFeed - X: 12000 mm/minFeed - Y: 5000 mm/minFeed - Z: 8570 mm/minTools speed: 0-3000 U/minWorkpiece table speed: 0-1500 U/minvoltage: 400 VControl: weight of the machine ca.: 11 tdimensions of the machine ca.: 5,85 x 8,3 x 3,8 mTechnical specifications: - CNC Siemens 840 sl - Swivel grab travel: 180 degrees Fluids: - Hydraulic: 150 l - Coolant: 850 l - Engine and hydraulic cooling: 100 l - Grease lubrication: 2 kg The data for this ad was create ...
used
pressure: . tstroke: 500 mmdaylight: 800 mmarbor support: 3000 Ram: 600x250 total power requirement: kWweight of the machine ca.: tdimensions of the machine ca.: mBanning feed unitAdjustable supports (1300 mm each)2 x roller conveyors (4000 x 800)Storage area (4000 x 1600)The tech. Data are manufacturer or operator information and therefore non-binding. We reserve the right to prior sale, Our terms and conditions of saleapply exclusively.About us Morethan 400 of our own machines in stockOver 15,000 m² of storage space, 70 t crane capacityMore than 10,000 items and accessories for your workshopIf you are interested in selling machines, production lines, or your business, please contact us. You can find further offers on our website. Tours are possible by appointment.We look forward to your visit.Your Markus Hirsch TeamThe data for this ad was created with ModulMWS - the software solut ...
Offer 25418 Technical data: - Printing capacity approx. 110 kN - Working stroke approx. 50 mm - Power stroke 12 mm - Projection approx. 150 mm - Table size 280 x 180 mm - Installation height adjustment up to max. 300 mm - 2 Hand control - Air inlet 6 - 8 bar - Total - space requirement approx. W 600 x H 2500 x D 900 mm - Weight approx. 400 kg
: 150 t: 3100 mm: 2600 mm: 400 mm: 200 mm: 600 mmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Hydraulic 4-Column Press manufactured in 2013. This Hymag HS 4 160-K features a press force of 1,600 kN and a stroke of 700 mm, making it suitable for metal pressing and forming applications. With a main motor power of 55 kW, this machine is designed for efficiency and reliability. If you are looking to get high-quality metal pressing capabilities, consider the Hymag HS 4 160-K machine we have for sale. Contact us for further details.
Hydraulic press manufactured in 1995. This EXNER EX SBR 200 features a pressing force of 2000 kN and a drive power of 78 kW. With an oil capacity of 1400 liters and a weight of 52000 kg, this machine is designed for robust performance. If you are looking to get high-quality pressing capabilities, consider the EXNER EX SBR 200 hydraulic press we have for sale. Contact us for further details.
: neu : ca. 10 Wochen ab Auftrags : Türkei : 88113 €: 1665.34 €: 220 to: 3050 mm: Y1 / Y2 / X Achse : 265 mm: 2600 mm: 450 mm: 530 mm: hydraulisch : 140 mm/s: 10 mm/s: 140 mm/s: 500 mm/s: 350 mm/s: 250 mm: 900 mm: 104 mm: 250 l: 22 kW: 4250 mm: 1770 mm: 3000 mm: 12600 kgStandard accessories:3 axes (Y1, Y2,X)CNC control DT-15- 2D grafic display 15",- intuitive touch-screen control (simple drawing of the bending outline with your finger)- user friendly programming in dialogue form- automatic calculation of the bending sequence- automatic calculation of the blank sheet size- graphic product and tool memory- correction possibility- USB interfaces for backup and programm transportation- PC software, generating programms on the PC and transfer to the machine by USBservo motorized back gauge on linear guides and ball screwsback gauge finger blocks on double linear guidesCNC crowning ta ...
990 € 
