Manufacturer:
(Category: 106)
An old eccentric press Elmerding with defective foot switch is available. Press capacity 30°: 25t, stroke adjustment range: 12mm-80mm, ram adjustment: 60mm, stroke rate: 120rpm, table adjustment: 150mm, safety distance: 144mm, weight: approx. 1450kg. Only 2-hand operation is possible. Documentation available. An on-site inspection is possible.
Press force: 250kN, ram stroke: 8mm-80mm, stroke rate: 180/min, installation height: 310mm, table dimensions X/Y: 550mm/400mm, ram dimensions X/Y: 355mm/220mm, machine dimensions X/Y/Z: approx. 1100mm/1400mm/2300mm, weight: approx. 2500kg. An on-site inspection is possible.
A single-column eccentric press Edelhoff including transfer unit is available. Press force: 130t, stroke adjustment: 30mm-130mm, ram adjustment: 75mm, stroke rate: 45/min, table dimensions X/Y: 1000mm/700mm, weight: approx. 5000kg. An on-site inspection is possible.
Press force: 650kN, Stroke: 150mm, Pressure piston diameter: 190mm, Column spacing X/Y: 950mm/460mm, Installation height: 500mm, Table dimensions X/Y: 900mm/870mm, max. stroke: 150mm, Operating pressure: 200bar, Machine dimensions X/Y/Z: approx. 1500mm/1750mm/2400mm, Weight: approx. 3000kg. Documentation available. An on site inspection is possible.
pressure: 800 tdistance between columns: 3160 mmstroke: 1100 mmcontrol: Siemens S5 distance table/blankh.,max. stroke up,adjustm. up: 1900 mmtable surface area: 3100 x 1900 mmdie-cushion pressure inside the table: 300 tstroke of drawing cushion in table: 400 mmdie-cushion pressure in pusher: 80 tstroke of drawing cushion in table: 150 mmram surface: 3100 x 1900 mmdie-cushion in pusher: hydraulic, controlled die-cushion inside the table: hydraulic, controlled total power requirement: 200 kWweight of the machine ca.: 150 tdimensions of the machine ca.: 4,95 x 3,3 x 10,2 mThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
pressure: 315 tstroke: 400 mmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
pressure: 160 tthroat: 400 mmstroke: 355 mmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Upgrading of the electrical system carried out in 2020. Press table dimensions: 530 × 640 mm approx. Clearance between shelves: approx. 220 mm Machine dimensions: 4200 x 2200 x 3500 mm approx. Panel dimensions: approx. 1400 × 500 × 2400 mm Capacity: 25 Ton Power: 40 kW Strokes per minute: between 775 and 1425 Warning: the information reported has been taken on board the machine and may not correspond to the actual performance. For further information, on-site inspection is suggested. The item is sold in the state in which it is, unverified and without warranty of operation. Item not subject to sales restrictions. Auction-ID: A7-44316-724
Key data: 100 t
For sale is a used spotting press from the manufacturer Reis with an adjustable press force of up to 100 t. The 4-column press has a table size of 1600 × 1300 mm, a maximum open height of 950 mm and an ejector in the table, making it particularly suitable for spotting, tuning and tool work in mould and tool making. Here are the technical data of the offered machine: Technical data + information: Spotting press – REIS TUS 80-100 Allgemeine Disclosures - Name: spotting press - Manufacturer: REIS - Type: TUS 80-100 - Type: 4-column press - Year of construction: 1998 - Press force: 26–100 T (adjustable) - Retraction force max.: 45 T - Table size: 1600 x 1300 mm - Max. table load: 5,000 kg - Open height max.: 950 mm - Overall dimensions (WxDxH): approx. 3400 x 4200 x 3700 mm - Total weight: approx. 8,500 kg - T-slots: DIN 650 – 22 mm Hydraulik - Hydraulic pum ...
Key data: 100 t
For sale is a hydraulic single-column press (C-frame) from the manufacturer Durendus with an adjustable press force of up to 100 T. The machine has a table size of 800 × 600 mm, a maximum installation height of 700 mm and an adjustable stroke of up to 500 mm, making it suitable for a wide range of pressing, assembly and forming work in industry and production. The machine shown here has already been built and delivered on behalf of a customer. We can manufacture this machine for you at very short notice – gladly taking individual options into account. Here are the technical data of the offered machine: Technical data + information: Hydraulic Single Post Press – C-Frame – 100 T Allgemeine Disclosures - Title: Hydraulic Single Column Press - Type: C-frame / single-column press - Manufacturer: DURENDUS - Press force: 15–100 T (adjustable) - Max. installation heigh ...
ZTS KOSICE LE 160 C eccentric press was built in 1988 in Czechoslovakia by Závody Tažkého Strojárstva n.p. Košice. The machine is in very good technical condition and has been regularly maintained throughout its service life. All control solenoid valves were replaced in February 2023. ZTS KOSICE LE 160C is an excellent choice for a wide range of workpiece machining, i.e. punching, cutting and stamping. All of these machining processes are performed with a high press force of 160 tonnes, which, combined with a rigid design, enables the production of parts with high repeatability and excellent precision. The ZTS LE 160 C eccentric press weighs 10150 kg. Technical specifications of the ZTS KOSICE LE 160 C press - maximum press force: 160 t (1600 kN) - maximum number of slider strokes: 50/min - number of slider strokes in single mode: 30/min - maximum slider stroke: 120 mm - ...
Due to internal production changes, we sell a hydraulic punching press according to the nameplate, this description and the following pictures. The sale is made without any warranty by Schako. Before recommissioning, the buyer must ensure that all regulations for operation are complied with The machine is immediately available and fully functional, but the light barrier does not comply with current regulations As far as we know, no operating hour meter is installed due to the age of the machine. We can note that the machine ran in single-shift operation for about 2-3 days per week. The machine table has a dimension of approx. 1000x800 mm
Due to internal production changes, we sell a hydraulic punching press according to the nameplate, this description and the following pictures. The sale is made without any warranty by Schako. Before recommissioning, the buyer must ensure that all regulations for operation are complied with. The machine is immediately available, fully functional, and was in regular use until the end of 2025 As far as we know, no operating hour meter is installed due to the age of the machine. We can note that the machine ran in single-shift operation for about 2-3 days per week. The machine table has a dimension of approx. 800x600 mm Options include a feed device and a coil unwinder (see pictures).
The machine is in good technical condition, after prior agreement it is possible to test it. - Nominal forming force: 120 t Working length: 3106 mm CNC control Delem (graphic 2D programming) Automatic calculation of bending sequence and collision detection Back gauge X axis with 2× manually adjustable stop fingers CNC electromotive height adjustment of the back gauge (R axis) CNC electrically controlled table deflection Upper tool adapter ROLLERI Equipment and accessories: - Front protective device (tilting door) - Rear protective device (sliding door) - 1× freely movable two-hand / foot control - Operating instructions including CE declaration
Key data: 20 t, 160 mm
Hello, We hereby offer you a used workshop press from Rodkraft, type WP 20F. Manufacturer: Rodcraft Pneumatic Tools GmbH & Co. KG Type WP 20 F Year of construction 2000 Machine No. P18096N Hydraulic stroke 160 mm Pressing force 20 t Machine dimensions 2150 x 960 x 660 mm Transport dimensions 2150 x 980 x 750 mm Machine weight 180 kg Note: The aforementioned technical data have been taken from brochures of the manufacturer or other sources, for which we cannot guarantee the accuracy and completeness. Scope of delivery: 1 piece used workshop press Rodkraft, type WP 20F Area of application and condition: The machine was used sporadically in a company locksmith's shop for squeezing / squeezing bearings, etc. The machine is fully functional and in good condition. We would be happy if this machine is interesting for you. Your service team Mertens & Frowein Gm ...
Hydropneumatic mode of operation Profile height: 200 mm under hold-down Max. Punch Height: 150 mm Wither height: 150 mm Weight: approx. 400 kg
Mechanical stamping press manufactured in 2002. This PRESSIX 160 CNR 6 features a capacity of 160 tons and an adjustable stroke ranging from 20 to 200 mm. It operates at a speed of 20 to 70 strokes per minute and includes a motorized slide adjustment of 100 mm. The table dimensions are 1100 x 700 mm, providing ample workspace. If you are looking to get high-quality stamping capabilities, consider the PRESSIX 160 CNR 6 machine we have for sale. Contact us for further details.
- Brand:AMADEO FARELL - To make bullets - Loading mouth: 1200 x 500 - Tunnel size: 800 x 600 - Motor: 15hp (11kw) - With electrical panel
Press brake Beyeler RT 80x3100 BJ 1992
nominal force - 4000 kN table - 1250x825 mm
Key data: 63 t, 500 mm
table - 750x560 mm lower ejector
Key data: 200 t
Capacity: 2000kN Year: 2017 Serial: 17X00095 Max Daylight: 1700mm Stroke: 1200mm Max Tooling Base Size: 2500x1500mm Max Advance Speed: 200 mm/s Electrical Supply: 415 Volts Phase: 3 Motor Rating: 50kW Continuous Approx. Net Weight: 25,000kg Max. Top Tool Weight: 10,000kg
Beutler P96-C630 - Eccentric Press - Mobile control panel - Infinitely variable drive - Clutch/brake combination - Overload protection in the ram - Light barrier - Gooseneck Lamp - Year of construction 1998 Technical data - Pressure: 630 kN - Stroke: 12 - 120 mm - Stroke rate: 30 - 130 rpm - Max. delay time: 96 ms - Projection: 300 mm - Distance table/plunger: 495 mm - Passage between body walls: 270 mm - Plunger area: 450 x 360 mm - Plunger adjustment: 120 mm - Table surface: 800 x 560 mm - Opening in the table: Ø 100 mm - Working height: 880 mm - Min. safety distance: 192 mm - Drive power: 5.5 kW - Operating voltage: 3x 400 V / 50 Hz - Machine dimensions WxHxD: 1800 x 2600 x 1600 mm - Dimensions control cabinet WxHxD: 800 x 1700 x 450 mm - Weight: approx. 5500 kg
Key data: 56 kN
Machine Type: Toggle Press Manufacturer: Gechter Type: HKPL 56 Condition: used / very good Offer will only be sent if a complete imprint is provided! Price 2.450 Euro incl. 19% VAT Fixed Price Location Warstein , Germany Reference number M-GEC-0126 DESCRIPTION We offer you a used toggle press from the manufacturer Gechter. With fine adjuster Weight approx. 205kg Max. power 56KN at 6.5 bar Availability: immediately Our offer is aimed at tradespeople who are registered within the meaning of the Trade Regulation Act according to §14 GewO. The offer is subject to change, subject to prior sale. Please provide your full contact details to receive a quote with our terms and conditions of payment. Errors in the descriptions and offers are reserved
pressure: 120/15 tdistance between columns: 860 mmstroke: 170 mmtable-size: 860 x 600 mmdayligth: 350 mmmax. distance table - ram: 520 mmram head dimension: 860 x 600 mmhole in the table: 200 x 140 mmtable height over floor: 850 mmtotal power requirement: 25 kWweight of the machine ca.: 7,5 tdimensions of the machine ca.: 2,3 x 1,7 x 3,4 mMaximum ram pressure: 120 kNMaximum pull-out pressure: 15 kNSick light curtainSafety distance: 180 mmMaximum overrun: 15 mmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
pressure: 200 tchamfer lenght: 4000 mmdistance between columns: 3550 mmControl: Delem weight of the machine ca.: 20.000 kgdimensions of the machine ca.: 5000x2000x3000 mmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
pressure: 040 tchamfer lenght: 1600 mmdistance between columns: 1100 mmstroke of upper beam: 100 mmthroat: 195 mmworking feed: 10.0 mm/secreturn speed: 70.0 mm/sec: 180 barwork height max.: 840 mmtable width: 110 mmdayligth: 295 mmControl: ATL 550 total power requirement: 5.5 kWweight: 2500 kgrange L-W-H: 2100 x 1200 x 1800 mmEquipment:- NC-controlled hydraulic press brake, with torsion shaft- with ATLANTIC NC control - model ATL 550 Positioning of the backgauge (X axis) Positioning of the depth adjustment (Y1 Y2 axis) Possibility of programming different programs Memory capacity max. 200 programs - max. 400 blocks Swivel control panel, left front- Electro-motorized backgauge (X axis) with 2x stop fingers, manually adjustable (R Z axis)- Tool holder system A - with top wedge crowning- Split insert/bending tools- Lateral safety guards- rear safety guard- 1x freely movable double foot swit ...
pressure: 035 tchamfer lenght: 1250 mmdistance between columns: 1070 mmpiston stroke: 150 + 60 mmcolumn arm: 410 mmtable height: 800 mmdayligth: 470 mmworking feed: 10.0 mm/secreturn speed: 70.0 mm/sectable width: 140 mmControl: ELGO NC Number of working hours: ~ 9.600 hoil volume: 80.0 loperating pressure: max. 240 barvoltage: 380 Vtotal power requirement: 4.0 kWweight: 2200 kgrange L-W-H: 1800 x 1450 x 2150 mm Well maintained condition With only approx. 9.600 operating hours ()Features:- Robust NC-controlled hydraulic press brake- With ELGO NC control unit P8822” Positioning of the backgauge (X axis) Positioning of the depth adjustment (Y1+Y2 axis) Swiveling control panel, front left- NC electric motorized backgauge (X axis) With 2x stop fingers, manually adjustable (R+Z axis)- 1x split set of pointed tools - top- 1x rotatable Multi-V die block- Side safety device (swivel doors)+ FIE ...
Press brake Manufacturer: Trumpf Type: TRUMABEND V230 Year of Make: 2000 Overhaul: 2010 CNC control: Delem DA 65 graphics Year of Make: 2000 Pressing force max.: 230 to. Max. working range: 3,060 mm C-stand projection: 410 mm Max. installation height: 535 mm Stroke bending beam max. : 365 mm Sheet thickness max. approx.: 12 mm Travel back gauge: 600 mm Passage between the uprights: 2,690 mm Weight: 18.210 kg Space requirement: 3,660 x 2,120 x 3,095 mm Basic equipment : Two-cylinder Y1/Y2 upper drive concept Version Y1/Y2 Electro-hydraulic plunger drive in proportional valve technology Pushrod travel measuring system with spring compensation via glass scales Modern block hydraulics Spherical suspension and inclined position of the pressure beam 2-axis backgauge system (R, X - CNC) New, secure finger adjustment from the front 2 pieces of sel ...
: neu : ca. 4 Monate ab Auftragse : Italien : 66700 €: 1260.63 €: 150 to: 500 mm: 1.550 x 2.000 mm: 800 mm: 20 mm/s: 3 mm/s: 2350 mm: 2000 mm: 2500 mm: 4100 kg: horizontal verschiebbar : 1550 mm: 1000 mm: 1300 mmhorizontal movable cylinderhydraulicaly movable standcontrol by levers as well as control panelaccording to CE regulations user manual in GERMAN and ENGLISHOPTIONS:Work table, welded to the base frame, with holes on the surfaceControl panel on the swivel arm (push buttons for press movement, solenoid valves, Siemens CPU)Radio control panel (push buttons for press movement, solenoid valves, Siemens CPU)Siemens control with touchscreenLifting cylinders in the table (6, 8 or 10 pcs.)No-rotation shaft for the piston2 speeds for stand movement and cylinderOil cooler and decompression valveThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Innovac GmbH
4.800 € 
