Manufacturer:
(Category: 106)
pressure: 100 tthroat: 415 mmstroke: 8-140 mmno. of strokes: 48 Hub/minram - range of adjustment: 80 mmtable surface area: 920x670 mmram surface: 700x450 mmtable height: 800 mmtool hole in ram: Ø 50 mmweight of the machine ca.: 8 tdimensions of the machine ca.: BxTxH 1500x2000x2800 mmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
pressure: 160 tthroat: 340 mmstroke: 20-120 mmno. of strokes: 45 Hub/minram - range of adjustment: 100 mmtable surface area: 800x620 mmram surface: 500x400 mmhole in the table: Ø 360 mmtool hole in ram: Ø 50 mmweight of the machine ca.: 12 tdimensions of the machine ca.: 2200x2000x3600 mmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
pressure: 100 tthroat: 330 mmstroke: 10-130 mmno. of strokes: 56 Hub/minram - range of adjustment: 80 mmtable surface area: 830x600 mmram surface: 250x130 mmtable height: 870 mmtool hole in ram: 50 mmweight of the machine ca.: 11 tdimensions of the machine ca.: BxTxH 2100x1900x3000 mmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
pressure: 75 tthroat: 310 mmstroke: 16-140 mmno. of strokes: 105 Hub/minram - range of adjustment: 80 mmtable surface area: 800x610 mmram surface: 600x175 mmhole in the table: Ø 170 mmtable height: 820 mmtool hole in ram: Ø 40 mmweight of the machine ca.: 4 tdimensions of the machine ca.: 1500x2000x2700 mmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
pressure: 63 tthroat: 280 mmstroke: 8-100 mmno. of strokes: 56/84 Hub/minram - range of adjustment: 63 mmtable surface area: 620x500 mmram surface: 310x260 mmhole in the table: Ø 250 mmtable height: 850 mmtool hole in ram: Ø 40 mmweight of the machine ca.: 4 tdimensions of the machine ca.: 1200x1900x2800 mmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
pressure: 360 tstroke: 60 mmtable surface area: 525x430 mmno. of strokes: 60 Hub/min: 40 mmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
pressure: 63 tthroat: 275 mmstroke: 8-120 mmno. of strokes: 30-120 Hub/minram - range of adjustment: 85 mmhole in the table: 220x100 mmtable surface area: 750x540 mmram surface: 400x260 mmtable height: 820 mmtool hole in ram: Ø 50 mmtotal power requirement: 7,7 kWweight of the machine ca.: 5 tdimensions of the machine ca.: BxTxH 1500x2000x2450 mThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
pressure: 30 tthroat: 180 mmstroke: 8-76 mmno. of strokes: 80-200 Hub/minram - range of adjustment: 60 mmtable surface area: 360x580 mmtable height: 840 mmhole in the table: Ø 110 mmram surface: 250x350 mmtool hole in ram: Ø 40 mmtotal power requirement: 3 kWweight of the machine ca.: 1,8 tdimensions of the machine ca.: BxTxH 1350x1200x2100 mmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
pressure: 150 tchamfer lenght: 3550 mmdistance between columns: 3050 mmControl: Cybelec DNC 880S stroke: 700 mmthroat: 350 mmdimensions: 4400x2200x3940 mmweight of the machine ca.: 15.000 kgAccessories/equipment:- Bending aid in front of the machine- Parking space for bending aid- 3 stop fingers- Control conversion 2011The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
pressure: 110 tchamfer lenght: 2550 mmControl: Cybelec CybTouch 15 weight: 9000 kgdimensions: 3000 x 2100 x 3000 mmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Single column - eccentric press WEINGARTEN type E 40 Masch. No. 643 / 62 Year of construction 1963 Pressure capacity 40 ton. Projection 250 mm Table opening 150 x 80 and Ø 200 mm Table area 560 x 460 mm Plunger area 250 x 200 mm Adjustable ram stroke 8-88 mm Plunger adjustment 63 mm Installation height 320 mm Clamping pin bore Ø 40 mm Stroke rate 100 / 130 strokes / min. Motor power 2.2 / 3 kW Mains connection 400 volts, 50 Hz Table height above floor 840 mm - Clutch-brake combination thanks to WEINGARTEN friction threaded clutch with OT flow protection - Electric stroke release via two-hand operation - Overload protection by crushing plate - Manual grease central lubrication - Front crankshaft support bearing - Control cabinet adjacent - UVV for manual insertion work Space requirements L x W x H 1800 x 1500 x 2200 mm Weight 3.1 ton.
Key data: 100 t, 355 mm, 125 mm
Press force 100 t The dimensions of the table top 1000 x 640 mm Stroke adjustment 125 mm Plunger adjustment 90 mm Stroke rate 75-150 rpm Main motor power 6/10 kW Machine dimensions L x W x H 1725 x 2230 x 2970 mm Machine weight 10100 kg
6500ton Open Die Forging Press HJ / Seonam (Korea) Design: Eastern European Corporation Installation: 2006/2008 Press Type: Four column push down Oil hydraulic system Nominal force (static working pressure of 320 bar): 5,000 Tons Up-setting force (static working pressure of 420 bar): 6500 Tons Daylight: 5,200 mm Stroke of Movable cross head: 2,700 mm Main Ram dia. (Center cylinder): 1 set - ￠950 mm Side Ram dia. (Side cylinder): 2 sets - ￠750 mm Return cylinder Ram dia: 2 sets - ￠300 mm Moving Table Width: 2,600×Length 6,600 mm Moving Table stroke (center to both side 2,750mm): 5,500 mm Approaching speed: 300 mm/sec Main cylinder Forging speed (2,200 tons/ 320 bar): 163 mm/sec All cylinder Forging speed (5,000 tons/ 320 bar): 73 mm/sec Up-setting Forging speed (6,500 tons/ 420 bar): 10 mm/sec Return speed: 270 mm/sec Hydraulic Main pump: 12 sets ...
Eccentric press with black shield, Pressure capacity 15 t, Stroke adjustment from 5 - 60 mm, Table dimensions: 550 x 360 Dimensions: W 800 x D 1200 x H 2200 mm Weight 800 kg,
Inv. Num. : 8001 Type: IM6120 Producer: KEYENCE Created: 2014 Parameters: Axis X: 100 mm Axis Z: 30 mm Measuring range: 200 x 100/125 x 25 mm Weight: 36 kg
Max. diameter of initial blank: 30 mm Blank length: -Min.: 120 mm -Max.: 300 mm Max. diameter of upset flange: 60 mm Upset slide nominal force: 2500 kN Max. force on clamping slide with dies closed: 2500 kN Stroke: -Movable die: 100 mm -Upset slide (full): 220 mm -Die closing: 140 mm Slide strokes per minute: 45 Machine overall dimensions: -Length: 6050 mm -Width: 4600 mm -Height: 2260 mm Machine weight: 24680 kg
Offer 24467 Specifications: - Max. pressing force 10 t - Max. ram stroke approx. 550 mm - Tool holder thread M 16 - Stand width approx. 1000 mm - Stand depth approx. 500 mm - Min. / max. installation height 450 / 1350 mm - Height-adjustable table - Space requirement approx. W 1600 x H 2650 x D 850 mm - Weight approx. 350 kg
Pressing force max KN 600 Withdrawal force max KN 300 Die Supporting force max KN 300 Die return force max KN 32 Upper punch travel mm 190 Upper punch adj.travel mm 200 Filling height max mm 180 Pressing travel max. mm 90 Withdraw travel max. mm 95 Top pressing travel max mm 18 Adjustment at Die position mm 50 Filler travel mm 140 Maximum forming Diameter mm 130 Cycle stroke /min 12-25 Main Motor Power KW 15 Total Power KW 15 Speed control method Inverter Driving pressure for Clutch MPa 0.55 Pre-load Travel mm 110 Total air consumption L/min 300 Total weight Kg 5800 Overall size H mm 3200 W mm 1750 D mm 1480
Inv. Num. : 7936 Type: T450 RCE Producer: Sangiacomo Created: 2018 Parameters: Compressive force: 450 t Table length: 1800 mm Table width: 1000 mm Stroke length: 20-250 mm Total power requirement: 37 kW Adjusting the ram: 120 mm Maximum stroke rate: 50 1/min Ram dimensions: 1400 x 900 mm Machine height: 4960 mm Machine width: 2880 mm Machine weight: 50000 kg
Inv. Num. : 7920 Type: UPW 12,5 Producer: VEB Wema Bad Düben DDR Created: 1980-GO 1998 Parameters: Rolling force: 12.5 t Max. workpiece diameter: 70 mm Workpiece width: 200 mm Power consumption: 4 kW Length: 1125 mm Width: 1400 mm Height: 1150 mm Weight: 2100 kg Equipment: Thread Rollers Ring magazine for automatic operation Support ruler
Inv. Num. : 7919 Type: UPW 12,5 Producer: VEB Wema Bad Düben DDR Created: 1986 Parameters: Rolling force: 12 5 t Max. workpiece diameter: 70 mm Workpiece width: 2000 mm Length: 1125 mm Width: 1400 mm Height: 1150 mm Weight: 2100 kg Equipment: Thread Rollers Ring magazine for automatic operation Support ruler
Inv. Num. : 7918 Type: UPW 12,5 Producer: VEB Wema Bad Düben DDR Created: 1984, GO 2006 Parameters: Rolling force: 12.5 t Max. workpiece diameter: 70 mm Workpiece width: 2000 mm Power consumption: 4 kW Length: 1125 mm Width: 1400 mm Height: 1150 mm Weight: 2100 kg Equipment: Thread Rollers Ring magazine for automatic operation Support ruler
2 x Schmidt Eccentric Press ZHS-4/36 - 600 tons of pressing force Good condition, fully functional, can be viewed and tried out on site. Shipping also abroad. Sightseeing: Basically, I would like to point out that the article can be viewed and tested under power before purchase in order to rule out misunderstandings. Please ask questions before purchasing to avoid confusion. If you have any general questions or would like to make an appointment for a viewing, I can be reached at any time on the telephone number below or above. Errors in the description and prior sale excepted. VAT is shown separately on my invoices. Shipping with forwarding agent.
Millutensil spotting press BV25/PM - Output force adjustable (with max. pressure): 100 - 800 kgf - Ejector stroke max.: 120 mm - Hydraulic pressure adjustable from 5 - 100 bar - Width: 150 cm - Depth: 150 cm - Height: 200 cm - With operating instructions Good condition, fully functional, can be viewed and tried out on site. Shipping also abroad. Sightseeing: Basically, I would like to point out that the article can be viewed and tested under power before purchase in order to rule out misunderstandings. Please ask questions before purchasing to avoid confusion. If you have any general questions or would like to make an appointment for a viewing, I can be reached at any time on the telephone number below or above. Errors in the description and prior sale excepted. VAT is shown separately on my invoices. Shipping with forwarding agent.
Control Thrust... 80t Bending length ... 2620mm controlled axes ... 4 Plunger stroke... 200mm Machine weight ... 5750kg The machine is in good condition, possible to test under power.
ULTRAPRAS WKR70H hydraulic press built in 2021 by the Polish company SAKOMET is designed for even the most demanding cold metal forming operations. The operations, such as precise cutting, stamping, punching and extruding of workpieces, are performed with a force of 16 tonnes using a hydraulic cylinder with a diameter of 100 mm. Induction limiters additionally allow adjustment of the piston advance and retraction limits, making the machine adaptable to the working range of various tools. In turn, centrally beneath the piston is a large cross-cut work table with a 90mm diameter bore. The UltraPras WKR 70H 16t hydraulic press weighs 420 kg. Technical specifications of the ULTRAPRAS WKR70H press - press force: 16 t - piston stroke: 70 mm - piston diameter: 100 mm - maximum working speed: 9.8 mm/s - minimum working speed: 2 mm/s - return speed: 20 mm/s - work table dimensions (L x ...
Description of the chip press: Powerful metal chip press with chip shredder for long turnings. The area of application is the processing of large quantities of milled and turning chips. Materials: aluminum, steel, cast iron Drip pan as oil tank Geared motor for optimal agitator operation Hydraulic Compression Cylinder Hydraulic press cylinder with two coaxial sections Diameter of briquettes 60 mm Automatic briquette length adjustment with displacement transducers Inductive Proximity Sensors Pre-compaction cylinder in conjunction with special compression hydraulic cylinder that compacts the material in the bushing-bulkhead unit Briquette ejection system, consisting of a compression chamber and a bulkhead with special anti-wear treatment Highly efficient closed-circuit oil cooling system consisting of an air/oil heat exchanger Hydraulic system with B ...
pressure: 100 tthroat: 315 mmstroke: 8 - 112 mmtable surface area: 725 x 570 mmram surface: 410 x 315 mmram adjustment: 80 mmno. of strokes: 55 / 82 Hub/mintool shank hole (depth x diameter): 85 x 50 mmdayligth: 355 mmtotal power requirement: 7,5 kWweight of the machine ca.: 6 tdimensions of machine L x W x H: 2,00 x 1,00 x 2,87 mThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Capacity, ton 630 Stroke path till its position where it develops nominal capacity, mm 16 Slider stroke, mm 320 Slider strokes, spm 20 Max. distance between table and slider, mm 800 Distance adjustment between table and slider, mm 180 Table size, mm 1250 x 1250 Slider dimensions, mm 1000 x 1000 Opening in the table, mm 800 x 800 Thickness of bolster, mm 180 Cushion stroke, mm 130 Main motor power, kW 58 Machine dimensions, mm 3280 x 3470 x 6190 Machine weight, kg 55500
Nominal force, kN 2500 Slider stroke, mm 400 Number stroke per minute 25 adjustment mm 260 Distance between table and slider, mm 750 Main motor power kW 47 Table size width / length mm 1250/2500 Dimensions of the machine Length Width Height (mm) 4555_2900_5855 Weight kg 50100
