Manufacturer:
(Category: 106)
CONTROLS PLC SIEMENS S7 PRESS DESIGN drive system: knuckle-joint frame design: H-frame, monoblock openings in uprights: yes number of suspensions: 2 feedstock transport direction: left to right PRESS FORCES total force (nominal): 315 to nominal work capacity: 38 kNmPRESS TABLE table surface (left-right): 2000 mm table surface (front-back): 1200 mm thickness of bolster plate: 200 mmSLIDE slide force: 315 to table surface (left-right): 1995 mm table surface (front-back): 1100 mm stroke: 160 mm stroke rate (max.): 80 /minSLIDE (MECHAN. PRESS) slide adjustment: 140 mm stroke rate (min.): 20 /min stroke rate (max.): 80 /min main drive power: 90 kWTOOL ASSEMBLY DIMENSIONS shut height (stroke down, adjustment up), BDC: 555 mm distance between columns (H-frame): 2060 mm passline opening (free passage in side columns): 1060 ...
pressure: 100 tthroat: 355 mmstroke: mmtotal power requirement: 11,5 kWweight of the machine ca.: 8,5 tdimensions of the machine ca.: mThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Key data: 3 t, 150 mm
For sale in new condition HYUNDAE CETTA HHP-3 hydraulic press "more pieces" manufacturer: HYUNDAE "Korea" type: HHP-3 year of manufacture: 2018 load range: 1-3 tons Stroke [mm] 150 open height: 250 mm -safety light gate -two-handed operation .-mobile work table Hyundae press control Pressing rod closing speed: 178mm/sec Pressing rod pressing speed: 54mm/sec Opening speed 79 mm/s Table size: 450x360mm Max. Working pressure: 60kg·f/㎠ Hydraulic motor 1,5 kW 3 phase/4P 200v Weight: 350kg machine height "without table": 1415mm machine length: 950mm machine width: ca 700mm working table with casters or level bolts
Key data: 5 t, 150 mm
Hydraulic Press Atsugi AP-5-KL Used Load Range: 20-50 (kN) Stroke (mm): 150 Lower Speed (Approach Fast Speed: 350 (mm/s) Lower Speed (Under Pressure Slow Speed: 36mm/s Rise Speed 250 (mm/s) Working Area Open Height: 250mm Open Depth: 180mm Table Size: 450x50mm Motor Specification 3 Phase AC200V 4P 1.5KW Two-Hand Operation . Mobile Worktable Fuel Oil / Quantity Daphni Hydraulic 46/9L Total Weight (kg) 270 Body Size Height (mm) 986 Width (mm) 485 Depth (mm) 920
Inv. Num. : 8585 Type: KPRW 160 Producer: Kieserling Created: 1972 Parameters: Compressive force: 160 t
Inv. Num. : 8584 Type: PEDA 160 Producer: IWK Created: 1972 Parameters: Compressive force: 160 t
Inv. Num. : 8583 Type: REP 100 Producer: Heilbronn Created: 1989 Parameters: Compressive force: 100 t Stroke length: 6-100 mm Maximum stroke rate per minute: 100 1/min Total power requirement: 11 kW Machine weight: 7000 kg
pressure: 60 tthroat: 280 mmstroke: 10-140 mmno. of strokes: 110 Hub/minram - range of adjustment: 60 mmtable surface area: 740x560 mmram surface: 380x195 mmhole in the table: 300x200 mmtable height: 760 mmtool hole in ram: Ø 40 mmweight of the machine ca.: tdimensions of the machine ca.: mThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
pressure: 35 tthroat: 220 mmstroke: 8-96 mmno. of strokes: 120 Hub/minram - range of adjustment: 50 mmtable surface area: 580x440 mmram surface: 305x170 mmhole in the table: 215x175 mmtable height: 870 mmtool hole in ram: Ø 40 mmweight of the machine ca.: tdimensions of the machine ca.: mThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
pressure: 45 tthroat: 230 mmstroke: 4-80 mmno. of strokes: 120 Hub/minram - range of adjustment: 55 mmtable surface area: 695x455 mmram surface: 365x180 mmhole in the table: 220x180 mmtable height: 890 mmtool hole in ram: Ø 40 mmweight of the machine ca.: tdimensions of the machine ca.: mThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
pressure: 100 tthroat: 300 mmstroke: 10-140 mmno. of strokes: 60 Hub/minram - range of adjustment: 60 mmtable surface area: 800x500 mmram surface: 430x230 mmhole in the table: Ø150 mmtable height: 860 mmtool hole in ram: Ø 50 mmweight of the machine ca.: 5,2 tdimensions of the machine ca.: mThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
The Dorst DK 250 is a robust used sizing and powder compaction press engineered by DORST, offering a substantial pressing force of up to 2500 kN. It supports operations with a maximum withdrawal force of 150 kN and a supporting force in the pressing position reaching 120 kN. Designed for precision, this model includes a 220 mm upper punch stroke with an adjustable travel of 120 mm. The press accommodates a pressing travel and withdrawal travel, each up to 50 mm, making it versatile for various pressing tasks. Operational performance ranges from 6 to 25 strokes per minute, and it provides a filling height of up to 100 mm. The Dorst DK 250 is efficient, consuming approximately 500 liters of air per minute and demanding a connected load of around 60.0 kW. Its dimensions, at 2500 mm in width, 1900 mm in depth, and 4800 mm in height, alongside a weight of approximately 18,500 kg, underscore i ...
AIDA NC2-250(1) 250t eccentric press in excellent condition /ctA2/ Manufacturer: AIDA Type: NC2-250(1) Push force: 160t Year of manufacture: approx. 1991 Stroke length: 170mm Distance above table: (adjustable) 280-400mm Table size: 2700x760mm Bear size: 2100x700mm Electrical power: 3x200V(), 30kW - Japanese standard Pgsc N D D Hou Dxb Tjxop Net weight: 35000kg Size: 2760x2800x3980mm Automatic greasing system. Automatic cutting oil dosing - RAZIOL EST-02 Optionally with disc winder and straightener.
Nominal pressing force ... 100t Table dimensions ... 1000 x 640mm Stroke adjustment ... 125mm Plunger adjustment ... 90mm Number of rams ... 75-150 rpm Main engine power ... 6/10kW L x W x H ... 1725 x 2230 x 2970mm Mechanical weight ... 10100kg
pressure: 25 tthroat: 200 mmstroke: mmpressure: 25 tno. of strokes: 140 Hub/minwindow in frame: 240 mmadjustment of stroke: 8...80 mmram - range of adjustment: 50 mmsurface of ram: 355 x 220 mmtable-size: 560 x 400 mmhole in table: 160 mmtotal power requirement: 3 kWweight of the machine ca.: 2,23 tdimensions of the machine ca.: m- distance table slide: 250 mmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
A Hämmerle hydraulic press brake is available. Pressing force: 2000kN, working length: 2600mm, installation height: 830mm, stroke: 265mm, throat depth: 300mm, rapid traverse: 100mm/s. Machine dimensions X/Y/Z: approx. 3750mm/2600mm/3600mm, weight: approx. 16000kg. The machine is not functional. Documentation available. On-site inspection is possible.
Key data: 75 t, 80 mm, 120 1/min
Pressure 75 t Stroke rate 120-600 / min Sheet width 10-300 mm Table size 1050 x 820 mm Pusher clamping surface 960x820 mm Distance table - UK plunger 380 mm Adjustable stroke - max. 80 mm Feed length 0-150 mm Total power requirement 20 kW Machine weight approx. 13 t Feed unit with max. belt speed 70 m/min Eccentric shaft with 4-fold bearings 2 connecting rods Central lubrication incl. magnetic belt conveyor - in use until 2020 -Operating instructions -Manual - Circuit diagram etc..
used
Bakker horizontal pressLength: 3500 mm Depth: 3100 mm Height: 1600 mm Weight: 6 ton
pressure: 200 tchamfer lenght: 3050 mmdistance between columns: 2550 mmstroke of ram: 274 mmcontrol: Cybelec ModEva Pac total power requirement: kWweight of the machine ca.: 17.000 kgdimensions of the machine ca.: mThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
pressure: 62 tdistance between columns: . mmstroke: 360 mmTable area: 2500x580 mmdayligth: 400 mmdiameter - coniflex cutter: Zilinderdurchmesser 200 mm0: 200 barStud passage: 590 mmtotal power requirement: kWweight of the machine ca.: tdimensions of the machine ca.: mVideo: https://www.youtube.com/watch?v=gkuLoo7ABkcThe tech. Data aremanufacturer or operator information and therefore non-binding. We reserve the right to prior sale, Our terms and conditions of sale apply exclusively.About us More than 400 of our own machines in stock Over 15,000 m² of storage space, 70 t crane capacity More than 10,000 items and accessories for your workshop If you are interested in selling machines, production lines, or your business, please contact us. You can find further offers on our website. Tours are possible by appointment. We look forward to your visit.Your Markus Hirsch TeamThe data for this ...
pressure: 120 tchamfer lenght: . mmdistance between columns: 2550 mmstroke: 200 mmtotal power requirement: 13,2 kVANumber of working hours: 2500 htotal power requirement: kWweight of the machine ca.: 8,3 tdimensions of the machine ca.: mThe tech. Data are manufacturer or operator information and therefore non-binding. We reserve the right to prior sale, Our terms and conditions of sale apply exclusively.About us More than 400 of our own machines in stock Over 15,000 m² of storage space, 70 t crane capacity More than 10,000 items and accessories for your workshop If you are interested in selling machines, production lines, or your business, please contact us. You can find further offers on our website. Tours are possible by appointment. We look forward to your visit.Your Markus Hirsch TeamThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Inv. Num. : 8499 Type: PEKRS 160 Producer: IWK Created: 1970 Parameters: Table length: 2000 mm Table width: 1000 mm Maximum stroke rate per minute: 55 1/min Stroke: 8-180 mm Adjusting the ram: 110 mm
Equipment Description Used Indirect Extrusion Press • Brand / Model: SMS Hasenclever 28 / 31.5 MN McKechinstrang” • Type: Horizontal indirect extrusion system for non-ferrous billets • Drive: Mechanical main unit with hydraulic auxiliaries • Country of Origin: Germany • Current Status: Dismantled and available for dispatch • Serial No. / Year of Manufacture: [To be confirmed] 2. Key Technical Specifications Parameter Value Main Piston Force 25.07 MN Total Press Force with Coupling 31.23 MN Max Stroke 3,070 mm Working Stroke 2,825 mm Ram Speed at 28 MN 0–64 mm/sec Ram Speed at 31.5 MN 0–57 mm/sec Billet Diameter Range Ø 230–355 mm Billet Length (cold) 320–1,320 mm Receiver Heating System Resistance; max 63 kW / 375 °C Shear Force 0.64 MN Profile Ejector Force 0.31 MN Actuation Differential Cylinders Ø 280/200 3. Included Components • B ...
pressure capacity max.: 80 tStroke: 500 mmtable surface area: 960 x 810 mmspindle pitch: 72 daylight between the columns: 950 / 540 mmpassage: 640 mmmachine weight ab.: 4500 kgdimensions of the machine ca.: 2,0 x 2,0 x 3,85 mHydraulic quick adjustment 500mmFlywheel Ø2000mm4 prism bases for straightening wavesdifferent support framesThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Offer 25200 Specifications: - Pressure capacity 200 t - Working width 3100 mm - Passage between the uprights 2600 mm - Table width 180 mm - Projection 300 mm - Installation height 450 mm - Feed speed 80 mm/sec. - Working speed 9 mm/sec. - Retraction speed 60 mm/sec. - Ram stroke 120 mm - Adjustment range fixed stops 120 mm - Drive 400 V / 18.7 kW - Space requirement approx. W 3300 x H 2950 x D 1900 mm - Weight approx. 10500 kg - with: - Adjustment of the crimping depth + baling pressure -Mot. Backgauge with handwheel fine adjustment - 4-fold universal die - sharpening tool - Two-hand control panel, foot switch,
Offer 25227 Specifications: - Pressure capacity 150 t - Working width 3600 mm - Passage between the uprights 3150 mm - Table width 180 mm - Projection 250 mm - Installation height 325 mm - Feed speed 70 mm/sec. - Working speed 7 mm/sec. - Retraction speed 60 mm/sec. - Ram stroke 120 mm - Adjustment range fixed stops 120 mm - Motor power approx. 7.5 kW - Oil filling approx. 300 l - Space requirement approx. W 3850 x H 2300 x D 1600 mm - Weight approx. 8700 kg - with: - Swivel arm – control panel with ATL 550 control - For crimping depth + backgauge -Mot. Backgauge - Crowning device - Lasersafe FIESSLER - 4-fold universal die, split sharpening tool + deer's foot tool - Two-hand control panel, foot switch,
High: 2.050 mm, Long: 750 mm, Force: 10 tons, Width: 600 mm, Weight: 800 Kg., Neckline: 150 mm, Stem travel: 200 mm, Rate of climb: 10 cm / sec, Piston rod ø of: 65 mm, Surface of the table: 300 x 300 mm., Specification: Hydraulics
