Manufacturer:
(Category: 106)
Description: Hydraulic single-column press with cycle feed Type: HEP 100 Specifications Electrical connection: 400 volts/50 Hz +/- 3 % Drive power: 5.5 kW Total power requirement: approx. 6.5 kW Control voltage: 24 volts/50 Hz +/- 3 % Hydr. Max. connection: 210 bar Set: 200 bar Performance data Ram speeds AB: approx. 48 mm/sec. at max. 100 kN compressive force Working speed AB reduced adjustable to: approx. 10 mm/sec. at max. 100 kN compressive force Ram speed ON approx. 96 mm/sec. at max. approx. 50 kN retraction force Plunger stroke: max. 200 mm Flow rate of the pump: approx. 15 l/min.
Single Column Press Dunkes TYPE: HZS 160 Specifications: Manufacturer: Dunkes Model: HZS 160 Operating hours: approx. 2250 The machine is in good condition and fully functional.
pressure: 150 tchamfer lenght: 4050 mmdistance between columns: 3550 mmControl: CYBELEC ModEva Pac throat: 350 mmdistance between table / ram: 430 mmtable width: 250 mmstroke: 250 mmtotal power requirement: 18,5 kWweight of the machine ca.: 16500 kgdimensions of the machine ca.: 4400x2100x3200 mmEquipment/accessories:- Control conversion at the end of 2018- Electric backgauge 1250 mm- 10-stage die displacement- crowning- EHT 26 mm tool holder- Axes controlled: Y1,Y2,X,R- Sheet metal holding table- 4x manually adjustable stop fingers- pneum. Upper tool clamping- Safety light curtain- 3x height-adjustable support arms- Oil cooler- 2-hand foot switchThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
pressure: 75 tstroke: 8-80 mmno. of strokes: 80-200 Hub/minram - range of adjustment: 70 mmtable surface area: 900x600 mmram surface: 900x470 mmhole in the table: 450x180 mmdist. between columns - front to rear: 500x350 mmdist. between pillars (front to rear): 788 mmtotal power requirement: 10 kWweight of the machine ca.: 10 tdimensions of the machine ca.: BxTxH 1600x1200x2800 mmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
pressure: 150 tthroat: 310 mmstroke: 30-120 mmno. of strokes: 20-60 Hub/minram - range of adjustment: 90 mmtable surface area: 820x600 mmram surface: 550x430 mmhole in the table: 330x200 mmtable height: 750 mmtool hole in ram: Ø50 mmweight of the machine ca.: 9,5 tdimensions of the machine ca.: BxTxH 2500x2500x3000 mmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
pressure: 35 tthroat: 240 mmstroke: 12-84 mmno. of strokes: 135 Hub/minram - range of adjustment: 70 mmtable surface area: 600x450 mmram surface: 360x180 mmhole in the table: 220x130 mmtable height: 630 mmtool hole in ram: Ø35 mmweight of the machine ca.: 2,5 tdimensions of the machine ca.: BxTxH 1500x2000x2600 mmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
pressure: 100 tthroat: 375 mmstroke: 20-125 mmno. of strokes: 60 Hub/minram - range of adjustment: 80 mmtable surface area: 920x660 mmram surface: 700x450 mmhole in the table: Ø90 mmtool hole in ram: Ø50 mmweight of the machine ca.: 8 tdimensions of the machine ca.: 2100x1500x3300 mThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
CONTROLS PLC SIEMENS S7 300 PRESS DESIGN drive system: hydraulic PRESS FORCES total force (nominal): 800 toPRESS TABLE table surface (left-right): 2600 mm table surface (front-back): 2000 mm height above floor level: 540 mmSLIDE stroke: 900 mmSLIDE (HYDR. PRESS) approximation velocity max.: 460 mm/s working velocity min.: 25 mm/s working velocity max.: 44 mm/s return velocity max.: 460 mm/sTOOL ASSEMBLY DIMENSIONS shut height (stroke down, adjustment up), BDC: 1700 mmELECTRICAL SPECIFICATIONS total power consumption: 180 kWDIMENSIONS / WEIGHTS total weight approx.: 95000 kgATTACHMENTS (PRESSES) press automation: yes gripper transfer system: yes acc. to actual accident protection regulation: yes European CE standards: yes Complete hot forming line consisting of: Hydraulic press NEFF 800 to. Ruhstrat furnace system:- Natural gas heat ...
pressure: 63 tthroat: 260 mmstroke: 8-100 mmram - range of adjustment: 63 mmno. of strokes: 115 Hub/min: 316 mmtable surface area: 630x490 mmram surface: 315x260 mmhole in the table: Ø 140 mmtotal power requirement: 4 kWweight of the machine ca.: 7,5 tdimensions of the machine ca.: 2000x2000x2700 mmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
A Durmazlar press brake distributed by Knuth is available. Pressing force: 35t, bending length: 1350mm, motor power: 5.5kW, stroke: 100mm, stroke rate: 17/min, max. operating pressure: 240bar, oil capacity: 150l. Machine dimensions X/Y/Z: approx. 1400mm/1400mm/2100mm, weight: approx. 1750kg, operating hours: 1258h. An on-site inspection is possible.
- Pressure capacity: 22 t - Projection: 175 mm - Stroke: 120 1/min - Plunger adjustment: 50 mm - Table height adjustment 50 mm - Stroke adjustment: 8-80 mm - Table: 520 x 400 mm - Plunger: 250 x 160 mm - Turnbuckle with trunnion clamping, D35 mm - Motor power 1.5 kW - Very smooth running - Mechanical disengagement of the rotary wedge coupling via pneumatic pneumatic cylinder - Pneumatic foot switch - No UVV - 4 pieces of machine feet - Connection cable CEE plug 16 A - Air connection with quick coupling - Weight: approx. 2,000 kg - Dimensions: Width 820 x Depth 1100 x Height 1800 mm
Capacity: 1600 tons Slide stroke: 300 mm Slide stroke length at maximum force: 0,16 mm Distance adjustment between tableand slider: 10 mm Slide stroke number in 1 min: 75 Length of a rod: 920 mm The closed height: 660 mm Table overall dimensions: 940x1200 mm Table height above floor level: 450 mm Slide overall dimensions: 860x910 mm The size of lateral windows: -Height: 560 E5931468 mm -Width: 600 mm Main motor: 110 kW Press overall dimensions: -Length: 5060 mm -Width: 3940 mm -Height above floor level: 5125 mm Press weight: 120 tons
Key data: 630 t, 275 mm
For sale is a used lowering press, manufacturer Sack + Kiesselbach, type EP 630. The machine is in very good condition. The press worked in an engraving company as a test press. Technical data: Pressing force: max. 630 tons. Installation height: max. 325 mm Stroke: max. 275 mm Weight: 4,000 kg
Key data: 100 t
Sale due to switch to eccentric press Pressing force 100 tons Loading depth 360 mm Stroke 500 mm Daylight 800 mm Plunger area 530 x 400 mm Table height above floor 710 mm Working speed 10mm/sec Approach speed 150 mm/sec Return speed 150 mm/sec Required power 17 kW Dimensions L x W x H 1,400 x 2,000 x 3,200 mm Weight of the machine approx. 5.1 t Year of manufacture 2001 Price is net, VAT can be claimed. Loading facilities available All information without guarantee
gebr. Post-bending press Fabr. Graebener, Type GRNM, YOC 2005 max. bending force 16 t. Tool length 1,600 mm Adjustment of the underswing, hydraulic 2 cylinders Dimensions 5080 x 3290 x 2540 mm Kj Uovvlllerhyxkenb Weight 65 t.
PRESS DESIGN drive system: eccentric / crank PRESS FORCES total force (nominal): 80 toPRESS TABLE table surface (left-right): 850 mm table surface (front-back): 550 mmSLIDE table surface (left-right): 560 mm table surface (front-back): 376 mm spigot hole diameter: 50 mm stroke: 110 mm stroke rate (max.): 60 /minSLIDE (MECHAN. PRESS) slide adjustment: 80 mm stroke min.: 0 mm stroke max.: 110 mmTOOL ASSEMBLY DIMENSIONS shut height (stroke down, adjustment up), BDC: 360 mmDIMENSIONS / WEIGHTS space requirements -left/right-: 855 mm space requirements -front/back-: 1635 mm total height: 2640 mm total weight approx.: 5400 kgATTACHMENTS (PRESSES) 2-hand engagement: yes foot engagement: optional European CE standards: yes
Pressing force: 4000kN, pressing pressure: 320bar, oil pressure: 250bar, blank holder force: 1600kN, blank holder stroke: 200mm, blank holder dimensions X/Y: 1000mm/800mm, blank holder ejector force: 160kN, ejector force: 63kN, ejector stroke: 100mm, overrun distance: 40mm, overrun time: 190ms. Documentation available. An on-site inspection is possible.
Punching force 45 t. 2 pcs. available from stock (Video under power on request)
Offer 25293 Specifications: -Max. Profile height up to 160 mm -Max. Profile width 100 mm - Tailings stroke 100 mm - Punching stroke 20 mm - Punching force at 6 bar 35 kN - Working pressure 6 - 8 bar - Air consumption per operation approx. 30 l - with: - Footswitch - 2 vertical, pneumatic hold-down devices - Adjustable punching heads - 2 swivelling support arms - Space requirement approx. W 980 x H 1400 x D 800 mm - Weight approx. 180 kg
pressure: 50 tchamfer lenght: 2500 mmdistance between columns: 2050 mmtable width: 140 mmtable height: 750 mmtotal power requirement: 8 kWweight of the machine ca.: 4,5 tdimensions of the machine ca.: 3, x 1,2 x 2,6 mEquipment:• manual back stop• upper and lower tools• 2 manual operation / foot switchThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
pressure: 20.0 tchamfer lenght: 850 mmdistance between columns: 850 mmback stop - adjustable: 375 + 400 mmstroke of upper beam: 196 mmdayligth: 470 mmajustment speed: 200 mm/sectable height: ca. 900 mmtotal power requirement: 5.0 kWweight of the machine ca.: 2500 kg New price ~ 85.000 euros well-kept / very good condition () with electromechanical direct drive (servo motor + ball screws) Machine is operated without hydraulic oil- in checked condition - machine video -https://www.youtube.com/watch?v=foxzKIA7vX8Description :High performance, fast travel speeds and the best ergonomicsthis bending machine to a perfect tool in terms of productivity andAccuracy.This allows an unrivaled high productivity in the field of small andmiddle bending parts can be achieved, since even complicated bending sequencesseveral stations can be processed very quickly.A large number of different and universally ...
pressure: 80.0 tchamfer lenght: 2550 mmdistance between columns: 2130 mmcolumn arm: 420 mmajustment speed: 100 mm/secworking feed: 10.0 mm/secreturn speed: 80.0 mm/secstroke: 200 mmdayligth: 470 mmtable width: 60.0 mmtable height: 910 mmNumber of working hours: ca. 37.102 htotal power requirement: 9.0 KWweight of the machine ca.: 5750 kgrange L-W-H: 3100 x 2180 x 2540 mm good / well-maintained condition ()- Inspected condition - Machine video -https://www.youtube.com/watch?v=fwdjSiQYq_AEquipment:- CNC electro-hydraulic press brake- OPERATEUR CNC control for 8 axes X1 + X2, Y1 + Y2, R1 + R2, Z1 + Z2- CNC-controlled backgauge adjustment (X-axes)- CNC-controlled vertical adjustment of the stop fingers (R-axes)- CNC-controlled left-right adjustment of the stop fingers (Z-axes)- Freely movable two-hand control & foot switch- Tool crowning - AMADA type- Various tools- CE marking- Side guards ( ...
pressure: 50 tchamfer lenght: 2500 mmdistance between columns: 2050 mmthroat: 200 mmtable width: 140 mmtable height: 750 mmdistance table - lower edge of ram: 300 mmmax. ram stroke: 100 mmclosing speed: 9 - 160 mm/secreturn speed: 55 mm/secvoltage: 380 V / 50 Hzengine output: 4,1 kWtotal power requirement: 5 kWweight of the machine ca.: 3,5 tdimensions of the machine ca.: 3, x 1,2 x 2,6 mEquipment:• manuel back stop• upper and lower tools Split , lower tool 2000 mm long• 2 manual operation / foot switchThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
pressure: 25 tno. of strokes: 1500 Hub/minsheet width: mmtotal power requirement: 20 kWweight of the machine ca.: tdimensions of the machine ca.: mThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
pressure: 25 tno. of strokes: 1500 Hub/minsheet width: mmtotal power requirement: 20 kWweight of the machine ca.: tdimensions of the machine ca.: mThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Key data: 250 t
Inv. Num. : 8652 Type: ZHS 250 Producer: ŽDB Hydraulika Generated: 2000 Parameters: Compressive force: 250 t Table length: 3500 mm Table width: 1200 mm Stroke: 700 mm Ram dimensions: 3500 x 1200 mm Working speed: 13-60 mm/s Machine height: 6000 mm Machine length: 3000 mm Machine width: 5000 mm Machine weight: 60000 kg
Inv. Num. : 8643 Type: LEK 250 Producer: ZTS Generated: GO Parameters: Compressive force: 250 t
pressure: 80.0 tstroke: 250 mmtable surface area: 1040 x 260 mmcolumn travel between the guideways: 1040 mmajustment speed: 8.0 mm/secworking feed: 5.0 mm/secreturn speed: 10.0 mm/secengine output: 5.5 kWweight of the machine ca.: 835 kg.dimensions of the machine ca.: 1810 x 700 x 2100 mmFurnishing:- Robust electro-hydraulic workshop press, with fixed cylinder- Ideal for aligning axles, shafts, etc., but also for pressing in and out of bolts, bearings, bushings and much more.- Robust welded steel construction for high demands- Table height adjustment via piston rod including round steel chain and 2x locking bolts Piston rod with metric socket- 1x set of V-block prism supports- Manometer for pressure display- simply constructed hand control with: 1x delivery speed 1x working speed 1x retreat speed- Piston can be stopped in any position- Hydraulic tank mounted on the side- Operation manua ...
pressure: 20 tthroat: 200 mmstroke: 0 - 50 mmtable:: 360 x 550 mmtable:: 140 mm - Bohrung no. of strokes: 160 Hub/minbore: 35,0 mm - Werkzeug compressed air: max. 6,0 bardayligth: 240 mmtotal power requirement: 2,2 kWweight: 1.250 kgrange L-W-H: 1310 x 1250 x 1860 mmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
