Manufacturer:
(Category: 106)
Pressing force max KN 600 Withdrawal force max KN 300 Die Supporting force max KN 300 Die return force max KN 32 Upper punch travel mm 190 Upper punch adj.travel mm 200 Filling height max mm 180 Pressing travel max. mm 90 Withdraw travel max. mm 95 Top pressing travel max mm 18 Adjustment at Die position mm 50 Filler travel mm 140 Maximum forming Diameter mm 130 Cycle stroke /min 12-25 Main Motor Power KW 15 Total Power KW 15 Speed control method Inverter Driving pressure for Clutch MPa 0.55 Pre-load Travel mm 110 Total air consumption L/min 300 Total weight Kg 5800 Overall size H mm 3200 W mm 1750 D mm 1480
Inv. Num. : 7936 Type: T450 RCE Producer: Sangiacomo Created: 2018 Parameters: Compressive force: 450 t Table length: 1800 mm Table width: 1000 mm Stroke length: 20-250 mm Total power requirement: 37 kW Adjusting the ram: 120 mm Maximum stroke rate: 50 1/min Ram dimensions: 1400 x 900 mm Machine height: 4960 mm Machine width: 2880 mm Machine weight: 50000 kg
Inv. Num. : 7920 Type: UPW 12,5 Producer: VEB Wema Bad Düben DDR Created: 1980-GO 1998 Parameters: Rolling force: 12.5 t Max. workpiece diameter: 70 mm Workpiece width: 200 mm Power consumption: 4 kW Length: 1125 mm Width: 1400 mm Height: 1150 mm Weight: 2100 kg Equipment: Thread Rollers Ring magazine for automatic operation Support ruler
Inv. Num. : 7919 Type: UPW 12,5 Producer: VEB Wema Bad Düben DDR Created: 1986 Parameters: Rolling force: 12 5 t Max. workpiece diameter: 70 mm Workpiece width: 2000 mm Length: 1125 mm Width: 1400 mm Height: 1150 mm Weight: 2100 kg Equipment: Thread Rollers Ring magazine for automatic operation Support ruler
Inv. Num. : 7918 Type: UPW 12,5 Producer: VEB Wema Bad Düben DDR Created: 1984, GO 2006 Parameters: Rolling force: 12.5 t Max. workpiece diameter: 70 mm Workpiece width: 2000 mm Power consumption: 4 kW Length: 1125 mm Width: 1400 mm Height: 1150 mm Weight: 2100 kg Equipment: Thread Rollers Ring magazine for automatic operation Support ruler
2 x Schmidt Eccentric Press ZHS-4/36 - 600 tons of pressing force Good condition, fully functional, can be viewed and tried out on site. Shipping also abroad. Sightseeing: Basically, I would like to point out that the article can be viewed and tested under power before purchase in order to rule out misunderstandings. Please ask questions before purchasing to avoid confusion. If you have any general questions or would like to make an appointment for a viewing, I can be reached at any time on the telephone number below or above. Errors in the description and prior sale excepted. VAT is shown separately on my invoices. Shipping with forwarding agent.
Millutensil spotting press BV25/PM - Output force adjustable (with max. pressure): 100 - 800 kgf - Ejector stroke max.: 120 mm - Hydraulic pressure adjustable from 5 - 100 bar - Width: 150 cm - Depth: 150 cm - Height: 200 cm - With operating instructions Good condition, fully functional, can be viewed and tried out on site. Shipping also abroad. Sightseeing: Basically, I would like to point out that the article can be viewed and tested under power before purchase in order to rule out misunderstandings. Please ask questions before purchasing to avoid confusion. If you have any general questions or would like to make an appointment for a viewing, I can be reached at any time on the telephone number below or above. Errors in the description and prior sale excepted. VAT is shown separately on my invoices. Shipping with forwarding agent.
Control Thrust... 80t Bending length ... 2620mm controlled axes ... 4 Plunger stroke... 200mm Machine weight ... 5750kg The machine is in good condition, possible to test under power.
ULTRAPRAS WKR70H hydraulic press built in 2021 by the Polish company SAKOMET is designed for even the most demanding cold metal forming operations. The operations, such as precise cutting, stamping, punching and extruding of workpieces, are performed with a force of 16 tonnes using a hydraulic cylinder with a diameter of 100 mm. Induction limiters additionally allow adjustment of the piston advance and retraction limits, making the machine adaptable to the working range of various tools. In turn, centrally beneath the piston is a large cross-cut work table with a 90mm diameter bore. The UltraPras WKR 70H 16t hydraulic press weighs 420 kg. Technical specifications of the ULTRAPRAS WKR70H press - press force: 16 t - piston stroke: 70 mm - piston diameter: 100 mm - maximum working speed: 9.8 mm/s - minimum working speed: 2 mm/s - return speed: 20 mm/s - work table dimensions (L x ...
Description of the chip press: Powerful metal chip press with chip shredder for long turnings. The area of application is the processing of large quantities of milled and turning chips. Materials: aluminum, steel, cast iron Drip pan as oil tank Geared motor for optimal agitator operation Hydraulic Compression Cylinder Hydraulic press cylinder with two coaxial sections Diameter of briquettes 60 mm Automatic briquette length adjustment with displacement transducers Inductive Proximity Sensors Pre-compaction cylinder in conjunction with special compression hydraulic cylinder that compacts the material in the bushing-bulkhead unit Briquette ejection system, consisting of a compression chamber and a bulkhead with special anti-wear treatment Highly efficient closed-circuit oil cooling system consisting of an air/oil heat exchanger Hydraulic system with B ...
pressure: 100 tthroat: 315 mmstroke: 8 - 112 mmtable surface area: 725 x 570 mmram surface: 410 x 315 mmram adjustment: 80 mmno. of strokes: 55 / 82 Hub/mintool shank hole (depth x diameter): 85 x 50 mmdayligth: 355 mmtotal power requirement: 7,5 kWweight of the machine ca.: 6 tdimensions of machine L x W x H: 2,00 x 1,00 x 2,87 mThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Capacity, ton 630 Stroke path till its position where it develops nominal capacity, mm 16 Slider stroke, mm 320 Slider strokes, spm 20 Max. distance between table and slider, mm 800 Distance adjustment between table and slider, mm 180 Table size, mm 1250 x 1250 Slider dimensions, mm 1000 x 1000 Opening in the table, mm 800 x 800 Thickness of bolster, mm 180 Cushion stroke, mm 130 Main motor power, kW 58 Machine dimensions, mm 3280 x 3470 x 6190 Machine weight, kg 55500
Nominal force, kN 2500 Slider stroke, mm 400 Number stroke per minute 25 adjustment mm 260 Distance between table and slider, mm 750 Main motor power kW 47 Table size width / length mm 1250/2500 Dimensions of the machine Length Width Height (mm) 4555_2900_5855 Weight kg 50100
Maximum force of slide: T 250 Stroke of slide: mm 400 Stroke rate per min 12 Adjustability of slide: mm 120 Bed area (W x D): mm 2500x1400 Main motor power: kW 32 Max depth of extraction 100mm pressing force during the maximum depth of extraction T 100 Force holding extract unit: T 50 Height above ground: mm 5000 Weight: 66 ton
BRUDERER BSTA 25 Precision high speed punching press. Nominal capacity: 250 kN; 25 tons. Min./Max. number of strokes: 100/1500. Max width of strip: 200 mm. Adjustable stroke: 13, 16, 19, 25, 32, 38 mm. Fitted with roll feeder BBV 202/120 on left hand side. Feed length variable up to 120 [mm] max. Optional: Sound insulating cabin. Condition: good working and visual order. Oil pump. Oil cooler. Execution: 4 supports. Front and rear safety guards. Fitted on rubber feet. Table dimensions: 530 x 530 mm. Passage between the supports: Longitudinal 540 mm; Lateral 200 mm. Slide/Ram adjustment 51 mm. Documentation in German or English language included. Press weight cca. 4800 kg. Press dimensions: 2055 x 1355 x H26200 mm.
Nominal force: 500 ton Slide stroke: 250 mm Slide strokes per minute: 25 Table dimensions: 1400 x 2500 mm Max distance between table and slide in its lower position at the upper position of adjustment: 750 mm Size of distance adjustment between table and slide: 250 mm Press dimensions (Length x Width x Height): 4130 x 2945 x 7200 mm Press weight: 69000 kg
Inv. Num. : 7827 Type: LKT 250D Producer: PRESSMONT Created: GO 2019 Parameters: Compressive force: 2500 kN Ram stroke: 250 mm Machine weight: 21000 kg
Technical data: Capacity, ton 1000 Ram stroke, mm 400 Max. ram strokes per min. 20 Shut height,mm 1000 Ram adjustment, mm 320 Table size, mm 3150 x 1800 Ram size (front-to-back), mm 1700 Column gap size, mm 1500 x 1900 Bolster plate thickness, mm 250 Ram travel to its extreme position where it develops nominal capacity, mm 12 Pneumatic cushion capacity, ton 200 Pneumatic cushion stroke, mm 200 Upper knock-out capacity, ton 50 Main motor power, kW 132 Press dimensions, mm 5150 x 4700 x 7830 Press weight, kg 200000
Herdwage n Glühöfen Kammerschmiedeöfen Wärmebehandlungskammeröfen Wärmebehandlungs Kammeröfen für ALU-Blechcoils Wärmebehandlungs Schachtöfen Haubenöfen Härten Anlassen bei niedriger und hoher Temperatur Glühen Normalglühen Austenitisieren Spannungsfreiglühen Vorwärmen vor dem Schmieden Rollenherdöfen Kontinuierliche Öfen für die Wärmebehandlung von buerstlein Nichteisenmetallbändern Anlage für Wärmebehandlung von Wagenfahrgestellgüsse Öfen für die Wärmebehandlung von Transformatorblech Warmrundlaufprüfanlagen Öfen für Feuerwiderstandsprüfungen zirlguss Hubbalken und Hubherdöfen Schachtofen Haubenofen Rollenherdöfen Durchstoßöfen Härten Glühen Normalisieren Weichglühen Vergüten Anlassen Entspannen Durchschuböfen Hubbalkenöfen Hubherdöfen Trockenöfen Rollenherdöfen Drehherdöfen Kammeröfen Mehrkammeröfen Verfahrbare Haubenöfen H ...
Inv. Num. : 7796 Type: HSA 200 T Producer: Hidroliksan Created: 2022 Parameters: Operating hours: 1600 h Compressive force: 200 t Maximum stroke: 450 mm Top table length: 1600 mm Top table width: 1400 mm Speed (high): 250 mm/s Speed (down): 160 mm/s Working speed: 5-18 mm/s Machine height: 5000 mm Machine length: 3650 mm Machine width: 3400 mm Machine weight: 18,000 kg
Used High Quality Bystronic pressbrake 6-axis for a sale.
pressure: ca.10 tthroat: anpassbar mmstroke: 250 mmtable surface area: 220 x 220 mm mmmaterial diameter max.: ca. Ø 267 mmtotal power requirement: 1,5 kWweight of the machine ca.: 430 kgdimensions of the machine ca.: 899 x 772 x 1520 mThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
pressure: 5 tdistance between columns: 300 mmdayligth: ? mmweight of the machine ca.: - tdimensions of the machine ca.: - mHandspindelpresse 5 toWorkspace: Tischfläche 280 x 260Control: ca. 180 mm HubThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
ULTRAPRAS UPV100TT SPECIAL hydraulic press built in 2022 Poland is the perfect choice for a range of demanding cold metal forming operations. This highly efficient and versatile machine can perform such operations as precision bending, profiling, flattening, bending, hole punching and stamping. Inside the robust design, there is a power unit-powered hydraulic piston with a diameter of 220 mm, which performs all these machining processes with a high press force of 100 tonnes. In addition, the entire working area is protected by light curtains, thanks to which the UltraPras four-column press also offers a high level of operational safety. During its service life, the machine has operated for just 595 hours and completed a total of 37042 work cycles. The UPV 100 TT SPECJAL 100t hydraulic press weighs 6500 kg. Technical specifications of the ULTRAPRAS UPV100TT SPECIAL press - maximum pre ...
pressure: 2 tdistance between columns: - mmstroke: ? mmthroat: ? mmtotal power requirement: kWweight of the machine ca.: tdimensions of the machine ca.: mhydraulic press 2tDrive: 0The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
WEINGARTEN DE 200-20 press built in 1975 in Germany is used for precision workpiece machining. The rigid construction combined with a high press force of 200 tonnes make the machine the perfect solution for mass production of various types of parts. The process of precision sheet metal pressing can be fully automated when the WEINGARTEN press is retrofitted with a sheet metal feeder. Technical specifications of the WEINGARTEN DE200-20 200 t press - press force: 200 t - maximum slider stroke: 200 mm - minimum slider stroke: 15 mm - maximum number of slider strokes: 60/min - minimum number of slider strokes: 20/min - slider adjustment: 110 mm
Key data: 250 t
Catalog No. : 7693 Type: CD 250 Producer: Mecamaq Made in: 2022 Characteristic: Pressing force: 250 t Maximum stroke: 250 mm Machine weight: 3200 kg
HUNGER Maschinenbau GmbH Press cylinder for a hydraulic metal scrap press / scrap press shear (Metso-Lindemann) fully assembled and ready for installation Piston diameter 260mm Piston rod diameter 210mm Stroke 8910mm Outer diameter of the housing 335 mm Cylinder head diameter 365mm Total length 10,635 mm Working pressure cylinder head 180 bar Working pressure cylinder base 225 bar Test pressure cylinder head 250 bar Test pressure cylinder base 315 bar Maximum pressure force 1195 kN Maximum tensile force 332 kN Medium hydraulic oil ISO VG46 Installation position horizontal
pressure: 20 tstroke: 200 mmtable-size: 550 x 550 mmworking speed:: 10 mm/ sec.work height max.: 940 mmtoolpiece height max.: 200 mmtotal power requirement: 2,2 kW: 200 x 10 mmweight: 650 kgdimensions: 1,1 x 0,6 x 1,22 mmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
pressure: 110 tthroat: 295 mmstroke: 20-120 mmno. of strokes: 60/90 Hub/minram adjustment: 85 kWtable surface area: 920x580 mmram surface: 540x280 mmhole in the table: Ø280 mmtable height: 830 mmweight of the machine ca.: 5,1 tdimensions of the machine ca.: BxTxH 1500x2000x2560 mmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
