Manufacturer:
(Category: 106)
pressure: 60 tthroat: 280 mmstroke: 10-90 mmno. of strokes: 110 Hub/minram - range of adjustment: 60 mmtable surface area: 750x540 mmram surface: 600x200 mmhole in the table: 300x200 mmtable height: 780 mmtool hole in ram: Ø35 mmweight of the machine ca.: 3,7 tdimensions of the machine ca.: 1800x1800x2700 mmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
The press is function with two adaptor Pressing force max. kN 1800 Pull-off force max. kN 1500 Counterholding force kN 1200 in pressing position Upper punch stroke mm 220 Filling height max. mm 180 Pull-off travel max.mm 90 Pressing path max. mm 90 Distance of upper pressure max. mm 18 Drive motor kW 30 Stroke rate (infinitely adjustable) min-1 6-24 Pre-suspension. Distance max. mm 62 (surcharge). Force max. kN 5.3 Total height mm 4700 Total width mm 2360 without electricity Total depth mm 2700 Hydraulic unit Total weight, net kg 17000
Nominal force, tf 1000 The slider does not reach BDC, mm 12.5 Slider stroke, mm 600 Frequency of continuous strokes, min-1 12...18 Highest frequency of single strokes, min-1 9...13 Closed height, mm 1500 Adjustment of closed height, mm 400 Slider dimensions, mm from left to right 4500 front to back 2500 Dimensions of the die plate, mm from left to right 4500 front to back 2500 Main drive electric motor power, kW 200 Overall dimensions, mm from left to right 6745 front to back 5400 height above floor level 9360 Weight kg 320000
Key data: 220 t, 4000 mm
with CNC-controlled crowning LazerSafe Safety system Foot pedal with standard tool set Machine in little-used condition Colour: turquoise/grey Total power requirement:f 15 kW Projection: 400 mm Stand width: 3150 mm Drive power: 400 V Back gauge: 625 mm Flow speed: 130 mm/sec Working speed: 8 mm/sec Retraction speed: 85 mm/sec Stroke length min./max:. 260 mm R-axis 150 mm Dimensions: 5100 x 1920 x 3080 mm Weight: 12250 kg Machine Number:M00000948 LZ: approx. 8 - 10 weeks, machine is repaired, checked, cleaned by a specialist and is then fully functional. Test run is carried out.
Motorized Rounding Machine Foot Holder one. Rear angle infeed Emergency stop leash very good condition Colour: grey Total power requirement 16 A Shaft diameter: 65 mm Capacity: 1020x1.5 mm Weight: 300 kg Machine number: 05 125 001 Machine is repaired, checked, cleaned by a professional and is then fully functional. Test run is carried out.
with the following standard equipment: Chromed cylinder, welded steel frame, oil pressure gauge, pressure adjustment Optional equipment possible for an extra charge: Pressure Regulator, V-Block, Automatic Control, Hydraulically Moving Cylinder Pressure: 80 t Stroke: 400 mm Total power requirement: 3 kW Machine weight: 725 kg Dimensions: 900 x 1560 x 2400 mm Passage in the table: 900 mm Working speed: 5.4 mm/sec Return speed: 8.3 mm/sec
Clutch hub for hot forging press K8548 6300T Weight, kg 7100
Driven gear for hot forging press 6300T Weight, kg 1300
Drive gear for hot forging press K8548 6300T Weight, kg 15 700
Eccentric shaft for hot forging press K8548 6300T Weight, kg 27 800
Maximum force ton-force 400 Slider stroke length mm 250 Slider stroke length to lower position mm 12 Slider strokes per minute 25 Number of single turn-on 19 Maximum distance between table and slider (in lower position of slider) mm 510 Adjustment mm 160 The sizes of a under-forginig plate mm 1000 Table overall dimensions: mm ·from front to rear 1000 ·from left to right 1000 The sizes of an aperture in a table mm 630 Slider overall dimensions mm 800 x 800 window dimensions in cheeks mm 600 Total power of electric motors kW 43,3 Press overall dimensions mm ·length 3470 ·width 3140 ·height 5940 Press weight without hydropneumatic pillow kg 31 400
Stock number: 3855 ECCENTRIC PRESS Manufacturer: PMB, Type: EPF 64 Machine NO.: 744103, Year of manufacture: 1974 Specifications: Gr. pressing pressure 64 to Table size 520 x 700 mm Stroke length 8-96 mm Projection 265 mm Total power 5.5 kW Control Fabr. Pneumatic clutch. Length: 2000 mm, Height: 2500 mm, Width: 1200 mm, Weight: 4000 kg
Used Feintool HFA 4000 equipped with Feeder Line Saronni total force 2500-4000 kN blank holder force 200-2000 kN back pressure force 100-1000 kN shearing force 1000-3700 kN safety distance 14 mm FEEDER LINE brand SARONNI year 2006 - completely overhauled in 2012
Bruderer BSTA 200 High-performance automatic punching press. max. pressure: 200 kN 20 T Speed range: 100 – 600 spm Year of construction: 1990. Feed BBV on the left side. Adjustable stroke: 8; 13; 19; 25; 32; 38; 44; 51 mm Ram height adjustment: 51 mm Dimensions of the clamping plate (clamping plate): 510 x 400 mm Bed opening: 400 x 160 mm Max. distance of the tool width between the columns: 410 mm. Connected load: 36 kVA Power 400 V 50 Hz Control voltage: 24 V Machine dimensions: H 2540 x W 1661 x D 855 mm Machine weight: approx. 3100 kg Switch cabinet and control system. Including all original technical documentation in German.
Specifications: - Max. working length 4050 mm - Column passage 3050 mm - Max. pressing force 110 t - Plunger stroke 200 mm - Projection 350 mm - Table height 900 mm - Opening width 400 mm - Drive power 17.5 kW - Space requirement approx. W 4250 x H 2850 x D 2200 mm - Weight approx. 15.0 t -with: - Control CYBELEC ModEva 10 S renewed in 2011 - Y 1+ 2 , X , Z - Two-hand control panel: -Mot. Back gauge 5 - 1000 mm - Front support arms - Split sharpening tool, - Universal die
pressure: 125 tchamfer lenght: 3000 mmdistance between columns: . mmControl: CNC type: DA 65 R stroke: 200 mmsafety distance: 136 mmrapid traverse - down: 100 mm/secrapid traverse - up: 92 mm/secworking feed: 1-10 mm/secthroat: mmtotal power requirement: kWweight of the machine ca.: 13 tdimensions of the machine ca.: mThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Inv. Num. : 7510 Type: EP 124 Producer: Elumatec Created: 2009 Parameters: Compressive force: 7 t Press height: 140 mm Machine height: 1230 mm Machine length: 1100 mm Machine width: 950 mm Machine weight: 545 kg
Nominal pressing force... 160t Table dimensions ... 1000 x 740mm Max. ram stroke... 25-160mm Plunger Dimensions ... 710 x 425mm Plunger adjustment ... 100mm Installation height ... 455mm Main engine power ... 11kW L x W x H ... 1380 x 1950 x 3350mm Machine weight ... 12180kg The machine is in good condition, possible to test under electricity.
PLASOMAT PMS 63 CP eccentric press was manufactured in Poland in 2004. In order to meet all production requirements, the machine features a large area slider with the possibility of adjusting the height and number of strokes in the control cabinet. In addition, a stable, deformation-resistant monolithic structure combined with a high pressing force of 63 tonnes ensures the highest accuracy and precision in machining. All this makes the PMS 63 CP press the ideal choice for both small batch and high volume production. The offer includes additional equipment, consisting of among others 8 anti-vibration pads and an intermediate table. Technical specifications of the PLASOMAT PMS 63 CP press - maximum press force: 63 t (630 kN) - work table dimensions (L x W): 800 x 560 mm - number of slider strokes: 65-85/min - maximum slider stroke: 110 mm - minimum slider stroke: 8 mm - slider adj ...
Key data: 10 t, 300 mm, 300 mm
more info on request
ressure: 800 tons Number of strokes per minute: 45 Slide stroke: 160 mm Adjustment of rod length: 15 mm Closed height: 630 mm Table size: 860х860 mm Max. distance between table and slide in its lower position: 630 mm Distance between guides: 670 mm Height of a table above floor: 700 mm Main motor power: 28 kW Press dimensions: -Left-to-right: 2290 mm -Front-to-back: 2800 mm -Height: 4910 mm Press weight: 31,8 tons
Dirinler CD/PC 600 H - Eccentric Press - incl. tools & accessories - Built in 1990 Specification - Capacity: 60 t - Stroke rate: 52 rpm - Plunger adjustment: 80 mm - Table dimensions: 750 x 480 mm - Plunger area: 360 x 250 mm - Table recess: Ø 170 mm - Projection: 250 mm - Engine speed: 1400 rpm - Motor power: 4 kW - Operating voltage: 400 V - Machine dimensions WxHxD: 950 x 2500 x 1900 mm - Dimensions control cabinet WxHxD: 60 x 115 x 35 mm - Weight: approx. 4000 kg
Eccentric press vineyard type AR160 tons With protective shield. YOC 1971 2 rotational speeds via mechanical gearbox Switchable. Central lubrication. Low-wear steep-threaded coupling. Table dimensions : 800x1000 mm Visits : possible at any time. Total weight approx. 10.5 tons
VORONEZH K8544 Hot Forging press YEAR : 1980 / 2008 OVERHAUL AND INSTALLED FORCE : 2500ton RAM STROKE : 350 mm RAM SIZE : 1120X1070 mm TABLE OVERALL SIZE : 1400X1200 mm NUMBER OF STROKES IN CONTINUOUS MODE : 60 NUMBER OF STROKES IN MANUAL MODE : 26 SHUT HEIGHT : 890 mm STROKE OF UPPER KNOCK OUT : 60 mm STOROKE OF LOWER KNOCK OUT : 70 mm MAIN MOTOR : 132KW (CHANGED TO HYUDAI HEAVY Y2012) PRESS OVERALL DIMENSION : 5380X4680X6400 mm HYDRAULIC BOLSTER NEW IN 2007 CONDITION : VERY GOOD WORKING CONDITIONS Trimming press available
Specifications: Capacity 40 tons 2 strokes 57 + 86 H/min Projection 250 mm Plunger stroke 8 - 88 mm Plunger adjustment approx. 63 mm Table , WxD approx. 570 x 450 mm Max. installation height approx. 330 mm
Specifications: Capacity 300 to Stroke rate 35 strokes Plunger width 1000 mm Projection 450 mm Plunger stroke 20 - 140 mm Plunger adjustment 80 mm Engine power 30 hp Weight roughly estimated 18 tons
Press capacity: max. 60 t Stroke of the punch: 125 mm Filling height: max. 110 mm Motor: 15 kW Approx: 1650x1801x3390 mm Net weight: 5800 kg
Key data: 15 t, 66 mm
Burger Press D07 Length 1.20 m Width 0.60 m Height 1.70 m 2 Hand control Switch to foot control 1 press die
