Manufacturer:
(Category: 106)
General Manufacturer: Transmatic Type: TS-3M Year of Make: 2007 Plate size: 38 x 38 cm Maximum pressure: 600 g/cm2 Temperature setting: 50 – 305°C Condition Condition: Used Functional: Tested and fully functional
CONTROLS PC controller BECKHOFF PRESS DESIGN drive system: knuckle-joint SLIDE total force (nominal): 250 to stroke: 61 mm stroke rate (max.): 60 /minCOUNTER RAM nominal force: 75 to stroke: 15 mmV-RING nominal force: 75 to stroke: 13 mmTOOL DIMENSIONS lower table (left-right): 540 mm lower table (front-back): 540 mm upper table (left-right): 540 mm upper table (front-back): 540 mm shut height max.: 320 mm ram adjustment: 145 mm distance between columns (H-frame): 560 mm passline opening (free passage in side columns): 270 mmSTRIP-FEEDER feeder type: roll feeder sheet width max.: 250 mm sheet thickness max.: 10 mm feeding step max.: 999.99 mm sheet length min: 1900 mm pilot release system: yes band lubrication system: yes Complete refurbished fineblanking press: disassembly into individual parts findings of all com ...
CONTROLS PLC SIEMENS S7 300 PRESS DESIGN drive system: hydraulic PRESS FORCES total force (nominal): 800 toPRESS TABLE table surface (left-right): 2000 mm table surface (front-back): 2000 mm height above floor level: 700 mmSLIDE table surface (left-right): 2000 mm table surface (front-back): 2000 mm stroke: 900 mmSLIDE (HYDR. PRESS) approximation velocity max.: 400 mm/s working velocity min.: 5 mm/s working velocity max.: 160 mm/s return velocity max.: 300 mm/sTOOL ASSEMBLY DIMENSIONS shut height (stroke down, adjustment up), BDC: 1700 mm distance between columns (H-frame): 2100 mmELECTRICAL SPECIFICATIONS total power consumption: 370 kW mains voltage: 400 V mains frequency: 50 HzDIMENSIONS / WEIGHTS total weight approx.: 81000 kgATTACHMENTS (PRESSES) press automation: yes gripper transfer system: yes acc. to actual acci ...
CONTROLS PLC SIEMENS S7-400 PRESS DESIGN drive system: hydraulic number of suspensions: 1 slide ejectors / cushion: no table cushion: no opening in table: no feedstock transport direction: back-front PRESS FORCES total force (nominal): 1000 toPRESS TABLE table surface (left-right): 2066 mm table surface (front-back): 2000 mm height above floor level: 630 mmSLIDE stroke: 900 mmSLIDE (HYDR. PRESS) approximation velocity max.: 600 mm/s working velocity min.: 15 mm/s working velocity max.: 40 mm/s return velocity max.: 390 mm/s return force: 100 toTOOL ASSEMBLY DIMENSIONS shut height (stroke down, adjustment up), BDC: 1710 mm distance table - slide max.: 1700 mmELECTRICAL SPECIFICATIONS total power consumption: 160 kW mains voltage: 400 V mains frequency: 50 HzDIMENSIONS / WEIGHTS height above floor level: 6500 mm t ...
PRESS DESIGN drive system: knuckle-joint frame design: H-frame, monoblock SLIDE total force (nominal): 160 to stroke: 60 mm stroke rate (max.): 72 /minCOUNTER RAM nominal force: 40 to stroke: 60 mmV-RING nominal force: 50 to stroke: 13 mmTOOL DIMENSIONS lower table (left-right): 470 mm lower table (front-back): 470 mm upper table (left-right): 500 mm upper table (front-back): 470 mm shut height max.: 277 mm ram adjustment: 80 mm distance between columns (H-frame): 500 mm passline opening (free passage in side columns): 220 mmSTRIP-FEEDER feeder type: roll feeder sheet width max.: 210 mm sheet thickness max.: 6 mm feeding step max.: 180 mmELECTRICAL SPECIFICATIONS mains voltage: 380 V mains frequency: 50 HzDIMENSIONS / WEIGHTS space requirements -left/right-: 1950 mm space requirements -front/back-: 1800 mm to ...
Press capacity: 50 ton Ram stroke adjustable: 16 - 51 mm Slide adjustment: 64 mm Free frontal opening L-R: 1100 mm Free lateral opening F-B: 250 mm Table surface area : 1080 x 650 mm Slide area: 980 x 420 mm Hole in table: 1060 x 200 mm Number of strokes: 100 - 750 s.p.m. Required power: 22 kW Working hours machine: 16850 h Height over floor approx.: 2471 x 1278 x 3150 mm Weight of machine approx.: 9 ton
Pressure total: 80 - 800 ton Ram stroke: 1600 mm Free frontal opening L-R: 2850 mm Free lateral opening F-B: 1000 mm Daylight: 1900 mm Table surface area : 2800 x 2000 mm Slide area: 2800 x 2000 mm Die cushion capacity in table: 32 - 320 ton Die cushion stroke: 400 mm Die cushion pad area: 2500 x 1700 mm Approach speed: 400 mm / sec Working speed: 5 -42,7 mm / sec Return speed: 420 mm / sec Required power: 246 kW Height over floor approx.: 7785 mm Weight of machine approx.: 100 ton No. of moving bolster: 1 pcs.
Pressure total: 140 ton Stroke: 800 mm Daylight: 1.004 mm Free frontal opening L-R: 2.060 mm Table surface area : 2.000 x 520 mm Slide area: 2.040 x 520 mm Working speed: 4 -20 mm / sec Rapid travel: 135 mm / sec Return speed: 120 mm / sec Weight of machine approx.: 14 ton Height over floor approx.: 4.810 mm Oil volume: 700 l
Press capacity: 315 ton Ram stroke adjustable: 30 - 100 mm Slide adjustment: 100 mm Shut height (stroke down, adjustment up): 370 mm Table surface area : 1600 x 1100 mm Slide area: 1600 x 1100 mm Hole in table: 600 x 180 mm Number of strokes: 15 - 180 s.p.m. Table height over floor: 1200 mm Required power: 170 kW Height over floor approx.: 4900 mm Dimensions L x W x H: 4900 x 1900 x 4900 mm Weight of machine approx.: 55 ton
Pressure total: 600 ton Ram stroke: 762 mm Slide adjustment: 406 mm Shut height (stroke down, adjustment up): 1322 mm Free frontal opening L-R: 3700 mm Table surface area : 3350 x 2134 mm Slide area: 3350 x 2134 mm Die cushion capacity in table: 180 ton Die cushion stroke: 305 mm Ejector in ram: 60 ton Ejector stroke in ram: 230 mm Number of strokes: 16 s.p.m. Required power: 90 kW Weight of machine approx.: 185 ton
Pressure total: 1400 ton Stroke: 950 mm Daylight: 2000 mm Table surface area : 3600 x 2500 mm Slide area: 3600 x 2500 mm Die cushion capacity in table: 400 ton Die cushion stroke: 500 mm Die cushion pad area: 3060 x 1860 mm Approach speed: 400 mm / sec Working speed: 40 / 80 mm / sec Return speed: 400 mm / sec Oil volume: 5000 l Required power: 450 kW Weight of machine approx.: 240 ton
Pressure total: 500 ton Stroke: 1100 mm Daylight: 1500 mm Table surface area : 2000 x 1250 mm Slide area: 2000 x 1250 mm Die cushion capacity in table: 160 ton Die cushion stroke: 300 mm Approach speed: 650 mm / sec Required power: 55 kW Weight of machine approx.: 50 ton
Capacity: 160 ton Throat depth: 350 mm Ram stroke: 20 - 140 mm Slide adjustment: 75 mm Shut height (stroke down, adjustment up): 740 mm Table surface area : 1000 x 680 mm Slide area: 600 x 300 mm Number of strokes: 50 s.p.m. Required power: 15 kW Weight of machine approx.: 12 ton
pressure: 6,3 tthroat: 200 mmstroke: 200 mmdayligth: 600 mmtotal power requirement: 2,2 kWweight of the machine ca.: 0,78 tdimensions of the machine ca.: - mHydraulic Press 63 kNStroke 200 mm, Throat 200 mm, feed rate: down 165 (28) mm/s, up 510 mm/s. Wheight 780 kg.Workspace: Table 450 x 380Drive: 2.2Movie: https://www.youtube.com/watch?v=tcxXfKlrFLYThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Press capacity: 160 ton Ram stroke adjustable: 20 - 130 mm Slide adjustment: 100 mm Daylight: 560 mm Table surface area : 1500 x 800 mm Slide area: 1400 x 800 mm Number of strokes: 20 - 60 s.p.m. Distance between the columns F - B: 520 mm Height over floor approx.: 3550 mm Required power: 48 kW Weight of machine approx.: 26 ton
diameter: 5 mmshaft length: 40 mmcutting lenght max.: 56 mmtotal power requirement: kWweight of the machine ca.: tdimensions of the machine ca.: mData on the machine type:Double-pressure rotor pressApplication: Screw productionMake: HilgelandYear of manufacture: 1990Max. wire diameter: 5 mmMax. shaft length: 40 mmMax. wire section length: 56 mmMax. output: 600 pieces/minMachine is fully operationalViewing possible by appointmentThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Qty. 1 Second-hand extrusion press line – in storage – never installed! Mfc.: Korean Manufacturer Force: 1650 UST Built: 2024 Type: Direct Single Action Horizontal Short Stroke Back Loading Aluminum Hydraulic: Rexroth PLC: Mitsubishi Diameter of billet: 152 mm (6 inch) Length: 400 – 750 mm Size of container: Φ157 mm × 800 mm Size of exit hole: Φ180 × 250 mm Container Size Inner Dia.: 164 mm (6˝) Length: 700 mm Main Ram Stroke: 1200 mm Scope of supply: Loading Lift System Billet Pushing Induction heating Furnace Billet Conveyor for Discharge Billet Feeding into Press Cooling System Hot Saw Run-out Table Double Puller Stretcher Finishing Saw Dies Furnace Aging Furnace
pressure: 100 tstroke: 400 mmtable surface area: 920 x 560 mmdayligth: 900 mmdistance between columns: 300 mmHeads: 175x115 mmfeed down: 7,6 mm/secfeed up: 13,4 mm/sectotal power requirement: 4,0 kWweight of the machine ca.: 1000 kgdimensions of the machine ca.: 1600x850x2450 mmDomestic equipments:- Stable welded construction- Pressure cylinder laterally adjustable- Electric control via selector lever / manually via hand lever- Pressure gauge via pressure gauge- Material requirements - CE markThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
pressure: 100 tthroat: 350 mmstroke: 130 mmstroke of worktool slide: 3070 Hub/minram adjustment: 100 mmram surface: 500x300 mmtable surface area: 1000x600 mmfeed - rapid adjustment: total power requirement: kWweight of the machine ca.: 9,8 tdimensions of the machine ca.: mThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
pressure: 20 tstroke: 150 mmdayligth: 700 mmOverall size: 670x870x1900 mmweight of the machine ca.: 200 kgDomestic equipments:- Stable welded construction- manually via hand lever- Pressure gauge via pressure gauge- CE markThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
pressure: 120 tstroke: 400 mmdayligth: 900 mmfeed down: 5,8 mm/secfeed up: 9,5 mm/secHeads: 200x125 mmtotal power requirement: 6 kWweight of the machine ca.: 1250 kgdimensions of the machine ca.: 1900x1000x2450 mmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
pressure: 200 tstroke: 400 mmFrame Width: 450 mmcolumn daylight: 1300 mmcylinder diameter: 170 mmwork height max.: 900 mmFront light range: 1400 mmLateral light range: 450 mmtotal power requirement: 7,5 kWweight of the machine ca.: 2600 kgdimensions of the machine ca.: 2500x1100x2800 mmAccessories / equipment:- stable welded construction- Pressure cylinder laterally adjustable- Electric control via selector lever / manually via hand lever- Pressure gauge via pressure gauge- Material supports adjustable in height by cylinder- CE markThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
pressure: 160 tstroke: 400 mmdayligth: 900 mmHeads: 225x135 mmfeed down: 6,2 mm/secfeed up: 9,8 mm/sectotal power requirement: 6 kWweight of the machine ca.: 1.300 kgdimensions of the machine ca.: 1640x1000x2550 mmAccessories / equipment:- stable welded construction- Pressure cylinder laterally adjustable- Electric control via selector lever / manually via hand lever- Pressure gauge via pressure gauge- Material supports adjustable in height by cylinder- CE markThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
pressure: 80 tstroke: 400 mmtotal power requirement: 4,0 kW: 7,4 mm/s: 11,5 mm/sHeads: 160x95 mmweight of the machine ca.: 725 kgdimensions of the machine ca.: 1560x850x2400 mmDomestic equipments:- Stable welded construction- Pressure cylinder laterally adjustable- Electric control via lever / manual over hand lever- Pressure gauge via pressure gauge- Material supports per cylinder in the height adjustable- CE markThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
: 60 tostroke: 400 mmdayligth: 900 mmHeads: 150x95 mmfeed up: 5,6 mm/secfeed down: 9,4 mm/secweight of the machine ca.: 700 kgtotal power requirement: 4 kWOverall size: 1460x850x2400 mmFurther information:stable welded constructionPrinting cylinder adjustableOperation electrically via shift lever / manually via hand leverPressure display by manometerHeight of material supports adjustable by cylinderCE markThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
pressure: 105 tchamfer lenght: 3100 mmdistance between columns: 2600 mmtable width: 100 mmtable height: 750 mmControl: DELEM DA 65 dayligth: 200 mmworking feed: 0 - 10 mm/secreturn speed: 0-100 mm/secrapid traverse - up: max. 100 mm/secvoltage: 380 V / 50 Hztotal power requirement: 11 kWweight of the machine ca.: 7,5 tdimensions of the machine ca.: 4 x 2,2 x 2,8 mEquipment:• CNC-control DELEM DA65 graphic video• manual back-off turning• upper and lower tool• 2 manual control / foot switchThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
pressure: 400 tthroat: 1140 mmstroke: 600 mmtable surface area: 2000x1000 mmPlate: 4000x1000x300 mmram head dimension: 2000x1040 mmCylinder: 300 mmDaylight: 650 total power requirement: kWweight of the machine ca.: tdimensions of the machine ca.: 3,9x4x4,2 mThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
pressure: 75 tstroke: 250 mmdaylight longitudinal/sideways: 800 x 215 mmdayligth: 170 - 885 mmworking pressure: 7,5 - 8.5 barweight of the machine ca.: 0,45 tdimensions: 1,2 x 0,8 x 2,1 mmHydraulic/pneumatic workshop pressCylinder can be moved sidewayspneumatic foot pedalWinch for table height adjustment2 pcs. pressing blocksCE markingThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Specifications: - Max. working length 4060 mm - Column passage 3680 mm - Max. pressing force 1700 kN - Max. distance table / plunger 385 mm - Stand projection 410 mm - Plunger stroke 215 mm - Lifting speeds - Downward speed idle max. 200 mm/sec - Upward speed 135 mm/sec - Downward pressing speed 1 to. 11 mm/sec - Total drive power 30 kW - Space requirement approx. W 5600 x H 3000 x D 2400 mm - Weight approx. 18000 kg - with: - with 6 axis CNC control DELEM - Two-hand control panel with foot switch - crowning device - Controlled backgauge with height adjustment 5 - 860 mm - hydr. Upper + Lower Tool Clamping - Die table displacement pneumatically supported
Inv. Num. : 8150 Type: PDqV 4-500 Producer: KRUPP Created: 1972, GO 2008 Parameters: Compressive force: 500 t Table length: 3000 mm Table width: 1800 mm Distance between frame walls: 3100 mm Maximum stroke rate upper table: 11 1/min Ram stroke: 850 mm Adjustment of the ram: 350 mm Main motor power: 75 kW Machine weight: 158000 kg According to the GO in 2008, the press was in operation for a maximum of 100 hours. In the years 1972–2008, the press was operated in two shifts.
