Manufacturer:
(Category: 102)
Hoofdspindelmotor: 26 kW - max. spindelsnelheid: 4000 tpm Onderspindelmotor: 11 kW - max. onderspindelsnelheid: 6000 tpm Gereedschaprevolver met 12 stations (aangedreven) - max. snelheid: 4500 tpm (5,5 kW) Toolsetter / tool eye Mayfran chiptransporteur De stangaanvoer is optioneel. MistCleaner is optioneel. De zwarte onderdelenvanger aan de voorzijde is optioneel.Swing over bed: 380 mm Distance centre tot centre: 504 mm Max longitudinal travel Z-axis: 625 mm Max cross travel X-axis: 234 mm Dia of spindle bore: 76 mm Power on the spindle: 18,5 kW Number of speeds: 4000 rpm Command: Mazatrol Matrix Nexus 2 Toolchanger: yes Number of tools: 12 positions
2008 Spindle module replaced Circumferential diameter over bed 630 mm Circumferential diameter over support 370 mm Spindle through bore 105 mm the machine is delivered with a 250 mm manual chuck. Spindle speed range 1: 4 - 430 rpm. Spindle speed range 2: 430 - 2500 rpm. Main motor power: 18.5kw S6-40%
swing diameter: 2000 mmturning height: 1800 mmControl: Siemens Sinumerik 840 Dsl turning speeds range: 2,8-315 U/mincross rail adjustment - vertical: 1200 mmcross rail adjustment - horizontal: +/- 1150 mm: 1500 mmbit feeder section: 240 x 240 mmMinimum immersion diameter: 340 mmcutting capacity: 50 kNmax. torque on the faceplate: 50000 Nmspeed range step 1: 2,8 - 80 U/minspeed range step 2: 12 - 315 U/minMax. clamping weight: 12000 Kgpower capacity faceplate: 105 kWweight of the machine ca.: 33 tdimensions of the machine ca.: 10 x 5 x 6,5 mFurther technical data: - Feed range of three-phase servo motors: 1–3000 mm/min, 0.01–50 mm/rev - Crossbeam travel speed: 425 mm/minFeatures/Accessories - Increased turning height (+600 mm) - Z-axis extended to 1500 mm - Magazine capacity: 20 positions - Magazine type: disc magazine - Max. tool length: 525 mm - Chip conveyo ...
Main spindle: Technology: Motor spindle Speed: 4,000 rpm Power (max.): 29 kW Torque (max.): 250 Nm Bar Passage: 76 mm Sub-spindle: Technology: Motor spindle Speed: 5,000 rpm Power (max.): 29 kW Torque (max.): 250 Nm Ejector: Pneumatic Travel in Z: 800 mm Tool carrier I (X/Y/Z): Technology: 12-station turret Tool holder: VDI30 Tool drive: 5,000 rpm, 6.7 kW, 25 Nm Travel in X/Y/Z: 260/100/800 mm Rapid traverse in X/Y/Z: 30/12/30 m/min Tool carrier II (X/Z): Technology: 12-station turret Tool holder: VDI30 Tool drive: 5,000 rpm, 6.7 kW, 25 Nm Travel in X/Z: 210/800 mm Rapid traverse in X/Z: 30 m/min Equipment/accessories: Chip management: Chip conveyor Coolant management: IKZ system with paper belt filter and high pressure, 40 bar Raw material feed I: Robot interface prepared Raw Material Feed II: Bar Feeder Interface Prepared Finished part removal ...
Key data: 650 mm, 1500 mm
Double Spindle 5-Axis/7-Axis CNC Double Spindle Turning and Milling Center Okuma Multus U3000 1SW 1500 Year of construction 2021 OSP P300SA IGF-D CNC Controller Circumferential diameter over carriage 650 mm Turning diameter max. 1,500 mm Main spindle: Spindle bore 91 mm Spindle drive power 15/22 kW Spindle speeds max. 4,200 rpm. Chuck diameter 250 mm C-axis 0.0001° Sub-spindle: Spindle bore 91 mm Spindle drive power 15/22 kW Spindle speeds max. 4,200 rpm. Chuck diameter 250 mm C-axis 0.0001° Tool support: Single tool carrier in the work area Tools for turning (L) and milling (M) CAPTO C6 Tool Holder Milling spindle drive power 19/25 kW Milling spindle speeds 50 – 12,000 rpm. Tool magazine and automatic tool changer 80 tool magazine positions Axes/travels: Flat path X 645 mm Perpendicular travel (off-center) 250 mm Longitudinal travel Z 1,600 m ...
Inv. Num. : 9065 Type: GLS 200 Producer: GOODWAY Created: 2016 Parameters: Control System: FANUC Series Oi-TF Switch-on hours: 15380 h Hours: 7757 h Max. turning length: 300 mm Grinding diameter: 350 mm Maximum turning diameter over bed: 500 mm Maximum turning diameter over support: 380 mm Maximum spindle speed: 4500 1/min Spindle passage: 65 mm Number of tool head positions: 12 Weight: 3200 kg Equipment: Chuck Tool probe Bar Feeder Grips
Key data: 2020 mm, 1600 mm, 350000 mm
Stock number: 4023 LATHE Manufacturer: SKODA, Type: SUT 200 TD x 35000 Machines NO.: ob22780, Year of manufacture: 1984 Specifications: Turning length 35000 mm Turning over transverse slides 1600 mm Ø Gr. turning diameter 2020 mm Max. weight in quill 63000 Kg Spindle Motors Power 2 x 82 kW Total power 2x150 kw kW Accessories: Querschlitte 2 x ( Double ) Universal chuck 2 x 2000 mm mm Ø Rotating bezel 6 Fixed bezel 5 + 2 mm Ø Tailstock 2 x Machine needs be to rebuild - with new control Length: 45,200 mm, Height: 3000, Width: 3500 mm, Weight: 150,000 kg
Key data: 500 mm, 1000 mm
Circumferential diameter over bed 500 mm, over support 290 mm Center width 1000 mm Speed range 1-3000 1/min, spindle nose bayonet Gr 8 Spindle bore 70 mm Tailstock quill MK 5 / stroke 160 mm incl. Control MTC K, Face Plate Fixed bezel with rolling heads Steel holder head system Multifix C with 1 cassette Coolant Setup
Key data: 330 mm, 850 mm, 190 mm
Circumferential diameter over bed / support 330 / 190 mm Center width 850 mm Bore 36 mm Speed range 60 - 2400 1/min Tailstock quill MK 3 / stroke 100 mm incl. accessories: 4-fold holder, chip back panel, T-slots in cross support Tightening tube for collets (New machine was designed according to DIN 8605)
Key data: 840 mm, 3000 mm, 490 mm
Circumferential. over bed 840 mm, over cross slide 490 mm Center width 3000 mm Speed range 10-1250 rpm, spindle nose DIN 55022 Gr. 11 Spindle bore 105 mm Feeds 0.060 - 1.4 mm // 0.024 - 0.518 mm Thread metric 1 - 224 mm Drive power 18.5 kW Quill path / cone 220 mm / MK 6 incl. Hardened and ground bed guides, electromagnetic brake of the main spindle mechanically driven upper support, rapid traverse longitudinal/transverse Multifix steel holder, fixed bezel 2-axis digital display,
Year of manufacture: 1978 / overhauled: 2024 Circumferential diameter over bed... 710mm Max. workpiece length ... 4000mm Circumferential diameter via support ... 420mm Spindle speed ... 90-1000 rpm L x W x H ... 6000x1440x1560mm Machine weight ... 3500kg The machine is in very good condition - after the general overhaul. More info on request. It is possible to visit our warehouse in Brno.
Year of manufacture: 1979 / overhauled: 2024 Circumferential diameter over bed ... 710mm Turning length... 2000mm Max. workpiece weight ... 850kg Circumferential diameter via support ... 420mm Spindle speed ... 10-1000 rpm Main engine power ... 7.5kW Machine weight ... 3000kg L x W x H ... 4000x1440x1560mm The machine is in very good condition - after the general overhaul. More info on request. Viewing is possible at our warehouse in Brno.
Year of manufacture: 1994 / overhauled: 2025 Circumferential diameter over bed ... 630mm Turning length ... 2000mm Circumferential diameter via support ... 340mm Main engine power ... 7.5kW L x W x H ... 4000 x 1400 x 1520mm Machine weight ... 2960kg The machine is in very good condition - after the general overhaul. More info on request. It is possible to visit our warehouse in Brno.
Circumferential diameter over bed ... 840mm Turning length ... 2750mm Max.workpiece weight ... 6000kg Circumferential diameter via support ... 530mm Spindle bore... 82mm Spindle speed ... 7-900 rpm The machine is in good condition, possible to test under power.
turning diameter over bed: 1420 mmturning diameter over slide rest: 1000 mmturning length: 15000 mmturning dia. in gap: 2050 mmspindle diameter: 160 mmspeed: 1 - 400 U/minfaceplate diameter: mmspindle motor: 30 kWtotal power requirement: - kWweight of the machine ca.: - tdimensions of the machine ca.: - m- 4-jaw face plate- 4 Steady rest- 4-way toolpost- Rapid traverse- tailstock- Taper turning attachmentThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
CNC Lathe Manufacturer: Gildemeister Type twin 42 Year of manufacture 2005 Control Siemens 840D Turning length 210mm 2 X 12-fold turret all places are powered Engine A 83700 Spindle A 50809 Machine has a defect in the pick-up spindle, probably bearing With Breuning Profimat bar loading magazine
Key data: 660 mm, 3000 mm, 440 mm
Sine 330/3000 D Well-maintained conventional lathe without mounted lathe chuck but with standard accessories The construction follows the classic design however, is based on a heavy, one-piece cast machine bed. How in the case of heavy lathes here, too, the adhesion between the engine and spindle via a manual Multi-plate clutch. With integrated Features such as the removable bed bridge, rapid traverse and a Taper turning device. WORKSPACE Workpiece length 3000 mm Turning diameter over bed 660 mm Circumferential Ø over support 440 mm Turning diameter without bridge 900 mm Bridge length 320 mm Bed width 400 mm TRAVELS X-axis travel 368 mm Travel Z1 axis 230 mm Swivel range upper slide 45° MAIN SPINDLE Spindle speed 25 1/min - 1600 1/min Spindle bore 105 mm Spindle holder D1-8 RUSH COURSE Rapid traverse X-axis 2000 mm/min Rapid traverse Z-axis 4000 mm/min ...
turning diameter over bed: 280 mmturning diameter over slide rest: 170 mmturning length: 600 mmweight of the machine ca.: 400 kgspindle passage: 26 mmspeeds: 55-2000 U/mintotal power requirement: 1,4 kWdimensions of the machine ca.: 1,5 x 0,8x 1,3 mIncluding EMCO SOD grinding supportIncluding EMCO 4-jaw chuckIncluding machine feetIncluding change gearsThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
faceplate diameter: 3600 mmswing diameter: 4500 mmturning height: 1850 mmmax. workpiece weight: kgvertical adjustment of the crossrail: mmtravel -x axis: mmtravel -y axis: mmtravel -z axis: mmturning speed range: 0,6- 50 U/minpower capacity: kWmax. torque on the faceplate: weight of the machine ca.: 72 tdimensions: mverticale turning machine double coloumn - digital scale - double coloumn - 2x ram - movable cross slide - extra toolholder (four station) on the side of facing plateThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Parallel Lathe SCULFORT type MAXICAP 315-3000 R Between points: 3000 mm Maxi Ø on bench: Ø 635 mm Maxi Ø over saddle: Ø 470 mm Maxi diameter in brocken bed: Ø 1000 mm x Width 200 mm Spindle motor: 13 CV Spindle diameter: Ø 71 mm Rotation: from 20 to 1300 RPM Square turret GOODSHAPE 3-jaws chuck Ø 380 mm Threadings: Metric + Whitworth Tailstock: CM5 Feeds: longitudinal + transversal auto advances Equipped with: 1 lubricant pump + 1 face plate Ø 1000 mm Equipped with: 2 fixed steadies: Ø 380 mm + Ø 1000 mm Voltage: 380 V Dimensions (L x W x H): 5200 x 1600 x 1700 mm Weight: approx 5 T
Inv. Num. : 9058 Type: SPV 40 CNC Producer: CZ. TECH Created: 2008 Parameters: Control system: SIEMENS Table diameter: 533 mm Feed length X-axis: 550 mm Feed length Z-axis: 850 mm Max. turning diameter: 850 mm Max. workpiece height: 800 mm Max. workpiece weight: 800 kg Weight: 12500 kg
Inv. Num. : 9056 Type: SPRY 40 CNC-D Producer: ZPS Created: 1994, GO 2016 Parameters: Control system: Siemens Sinumeric 840D Maximum turning length: 300 mm Max. turning diameter: 110 mm Maximum main spindle power: 10 kW Spindle bore: 50 mm Max. rod diameter: 40 mm Weight: 2400 kg Equipment: Duplomatic tool head with rotary tools 3 meter pole holder
Offered is a precision lead and feed screw lathe: Center distance: approx. 1000mm, center height: 180mm, swing diameter over bed: 360mm, spindle bore: 35mm, spindle mount: D1-3 Camlock, spindle taper: MK5 (MT5), speed steps: 12 speeds, speed range: approx. 40-1800rpm, longitudinal feeds: 0.05-0.7mm/rev, cross feeds: 0.02-0.4mm/rev, metric threads: 0.4-7.0mm, inch threads (Whitworth): 4-56threads/inch. Inspection possible by appointment.
turning diameter: 250 mmturning length: 600 mmcontrol: FANUC Series 31i-Model A total power requirement: 23 kWweight of the machine ca.: 7,7 tdimensions of the machine ca.: 2.880 x 2.130 x 1.990 mm mThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Offered is a CNC vertical turning machine - pick-up system. Chuck diameter: approx. 160mm - 200mm, swing diameter: approx. 270mm, travels X/Z: approx. 500 - 600mm/approx. 160 - 200mm, max. spindle speed: 6000rpm, tool carrier: 12-station turret, drive system: Siemens SIMODRIVE 611, hydraulic unit: available, coolant system: including pumps and filter (One Eye Ind. magnetic filter installed), hinged belt chip conveyor. Inspection is possible by appointment.
Key data: 500 mm, 1000 mm, 2500 1/min
Lathe Voest Alpine Steinel WNC 500 S x 1000 Turning diameter 500 mm Turning length: 1000 mm Control system Sinumerik 810 T-GA 2 2 stage gearbox i = 4 Power: 37 KW at 100% ED Max. torque during turning: 1450 Nm Tailstock manual with clamping and coupling Speed max 2500 rpm Electronic handwheel For milling: Hydraulically swivelling servo motor with 720 Nm and max. 18.5 rpm 12-speed disc turret with driven tools max. 3000 rpm at 4 kw Tool holder VDI 40 Many VDI 40 tool holders for internal and external machining as well as driven tools, incl. some tools - e.g. internal turning steels otherwise without tools!
DMG MORI NRX 2000™ CNC Lathe TECHNICAL FEATURES: Year: 2017 NC Type: MITSUBISHI M730UM Maximum diameter Machinable: 150 [mm] X-axis travel: 100 [mm] Z-axis travel: 220 [mm] X1 Axis Fast Feed Speed: 30000 [mm/min] Fast feed speed X2 axis: 30000 [mm/min] Z1 axis fast feed speed: 30000 [mm/min] Z2 axis fast feed speed: 30000 [mm/min] Spindle Nose: JIS A2-5 Maximum length Machinable Spindle 1: 100 [mm] Maximum length Machinable Spindle 2: 100 [mm] Maximum speed Spindle 1: 6000 [rpm] Maximum speed Spindle 2: 6000 [RPM] Turret Turning Tool Power 1: 1.5 [kW] Turret 2 rotating tool power: 1.2 [kW] Number of posts - Turret 1 : 10 Maximum speed Rotating Tools - Turret 1: 10000 [RPM] Number of posts - Turret 2: 10 Maximum speed Rotating Tools - Turret 2: 10000 [RPM] Installed power: 38 [kVA] Supply voltage: 400 [V] Working time: 12270 [h] Weight: 5700 [Kg] EQUIPMEN ...
A CNC flatbed lathe Optimum is available. Swing diameter over bed/slide: 280mm/170mm, center distance: 700mm, spindle bore: 27mm, speed: 4000rpm, travel X/Z: 165mm/660mm, feed X/Z: 2m/min/3m/min, tool stations: 4, quill stroke: 85mm. Machine dimensions X/Y/Z: approx. 2000mm/750mm/1550mm, weight: approx. 450kg, control: Siemens Sinumerik. Documentation available. An on-site inspection is possible.
turning diameter: 1500 mmturning length: 4500 (5500) mmcontrol: Siemens 840 Dsl max. workpiece weight between centres: 6000 kgtotal power requirement: kWweight of the machine ca.: 40 tdimensions of the machine ca.: mCNC machine configured as a 4-way center lathe with full travel over the steady rests and superstructuresZ-axis travel (longitudinal slide) = 5000 mm (6000 mm with TAE3)X-axis travel (transverse cross slide) = 1000 mmY-axis travel (vertical movement) = 350 mmMaximum workpiece diameter = 1500 mmSwing diameter over cross slide = 1500 mmCenter distance = 4500 mm (5500 mm with TAE3)The cross slide and cross slide do not restrict the diameter range due to their lateral positioning on the lathe bed. Therefore, there is no associated diameter restriction over the cross slide/tool carrier.The cross slide unit, including the cross slide superstructure, can travel completely past the ...
