Manufacturer:
(Category: 101)
x-travel: 1100 mmy-travel: 600 mmz-travel: 500 mmtable surface area: 1300 x 600 mmspindle taper: SK 40 spindle turning speed - stepless: 10.000 U/minATC: 40 Poscontrol: HEIDENHAIN, TNC 530 total power requirement: kWweight of the machine ca.: 8,8 tdimensions of machine L x W x H: 2,58 x 3,04 x 2,35 mAccessories: 2 hydr. vices make HILMA, model NC 160, width of jaws 160 mm, various tool holders, chip conveyor, coolantThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
x-travel: 1500 mmy-travel: 800 mmz-travel: 700 mmtable surface area: 1760 x 700 mmspindle taper: SK 40 spindle turning speed - stepless: 8000 U/minspindle drive: 15 kWfeeds: 1 - 8000 mm/minrapid traverse X/Y/Z axis: 15 / 15 / 12 m/mintable load: max. 2500 kgspindle throat: 760 mmATC: 40 Poscontrol: HEIDENHAIN, TNC 530 total power requirement: kWweight of the machine ca.: 12,5 tdimensions of machine L x W x H: 4,23 x 2,98 x 2,74 m- with coolant through spindleAccessories: NC-dividing unit (=4th Axis) with tailstock, center height 250 mm, 2 hydr. vices make HILMA, model NC 160, width of jaws 160 mm, various tool holders, chip conveyor, coolant- geometrical overhauled in 2022 -- new ball bearing spindle installed on Y-axis in NOV. 2022 -- the magnetic plates shown on the photo are not included -The data for this ad was created with ModulMWS - the software solution o ...
x-travel: 710 mmy-travel: 630 mmz-travel: 500 mmtable surface area: 1100 x 585 mmrotary table dia.: 500 mmspindle taper: SK 40 spindle turning speed range: 5 - 6300 U/minspindle power: 11 kWno. of tools in magazin: 2 x 22 control: HEIDENHAIN, TNC 426 total power requirement: 20 kWweight of the machine ca.: 5,8 tAccessories: various tool holders, probe RENISHAW OMP 60, coolantThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
bore capacity in steel (diameter): 50 mmarm length: 1100 mmworkpiece height max.: ca. 1000 mmbore capacity in cast iron: 60 mmspindle taper: MK 5 spindle turning speed range: 28 - 2500 U/minfeeds: 0,05 - 2 mm/Uquill stroke: 300 mmdistance basic plate - spindle nose: 630 - 1380 mmcrossrail adjustment vertical: 750 mmtotal power requirement: 6 kWweight of the machine ca.: 4 tdimensions of machine L x W x H: 2,74 x 1,14 x 2,59 mm- with thread cutting attachment -Accessories: box table 550 x 550 x 550 mm, vice, coolantThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
table length: 2000 mmtable width: 2000 mmtable load: 25 ttable rotating: 360 °Control: total power requirement: 4 kWweight of the machine ca.: 8,2 tdimensions of the machine ca.: 3 x 2,9 x 0,9 mBoring mill table Skoda E25A- Boring mill table Skoda E25A- Dead weight: 8,2t- Max. Clamping weight. 25t- First commissioning: 1996- Decommissioned and stored since 2014- All axes are electrically controllable and ready for operation- 360° rotary drilling table ready for operation- Dimensions: see data sheet- Heidenhain rotation measuring system with digital display ready for operation- Heidenhain linear measuring system with digital display ready for operation- Boring mill table fully functionalThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
GeneralCNC Turning Centre; Control: CELOS with Siemens 840D sl Operate Working areaSwing diameter over guide ways620 mmTransverse stroke260 mmLongitudinal stroke795 mmClamping chuck diameter max.315 mmWork spindle (left)Spindle bore91 mmSpindle diametre on front bearing140 mmMain drive 1Drive power (100% DC)22 kWSpeed range- 4000 rpmTorque (100% DC)410 NmMax. torque (40% DC)525 NmAccuracy at point stopping0,001 degreeTool holder 1Number of tool stations12 Shank diametre according to DIN 6988040 mmNumber of driven tools12 Speed max.-6000 rpmPower max. (100% DC)10 kWFloor space/WeightDimensions (L x W x H)3,99 x 2,03 x 2,2 mWeight approx.6500 KgTechnologie cycle alternating speedTechnology cycle for the application of an alternating speed for vibration sensitive set-ups (Only in conjunction with Siemens control)Chuck rinsing device, outsidechuck rinsing device, outside (main spindle)Main s ...
GeneralTwo spindle Swiss turning automatic lathe; Control: Fanuc 310is Working areaBar diameter max.42 mmChanging kit from steady to sliding headstockChanging kit from steady to sliding headstock including application bush type Dunner B236 and bush-spindle syncronismDrive for support for back workingDrive for support for back working operation (slide 2) power 0.55 KWAxial drilling unit for back work.oper.Axial drilling unit for support for back working operation (slide 2) with 2 rot.spindles, junction for collet ESX/ER 20 and 2 cyl.junction diam.25mmDouble tool h. for ext.machining on rev.Double tool holder for external machining on revolver for shaft 16x16Double drill hold. on rev.cyl.junct.d.25Double drill holder on revolver with cyl. junction diam.25mmRad.driven mill.-drill.unit on rev.Radial driven milling and drilling unit on revolver with junction for collet ESX/ER 20 ratio 1:1 ...
GeneralCNC Swiss type lathe with Fanuc control; Control: FANUC 310 iTB Working areaTurning diameter33 mmSpecial equipmentHinged belt chip conveyor with Discharge height 1200 mm Aut. bar feeder IEMCA BOSS 545/32 E, max_ L=3200 mm, incl. guide channel diam. 18 mm
x-travel: 600 mmy-travel: 400 mmz-travel: 400 mmcontrol: MSX 501 Mori Seikiwork table:: table surface area: 700 x 450 mmmax. table load: 350 kgnumber of T-slots: 4 T-slot - width: 18 mmT-slot - distance: 100 mmMain spindle: Number of revolutions: 12.000 U/minpower capacity - main spindel: 18,5 / 15 / 11 kWtool taper: BT 40 max. Torque: 110,5 Nmdiameter of forward milling spindle bearing: 70 feeds: rapid travel x/y/z: 20.000 mm/minfeed speeds: 1 - 20.000 mm/minTipp feed: 15 Steps / 0 - 1.260 mm/minTool-Presetter:: Number of Toolpositions in magazine: 40 Pos.Max. mould width: 80 mmmax. tool-dia with free toolbox: 125 mmmax. tool length: 250 mmmax. tool weight: 8 kgchange-time chip to chip: 2,8 secchange-time tool to tool: 1,0 sectotal power requirement: 34 kVAweight of the machine ca.: 7,2 tdimensions of the machine ca.: 2,8 x 3,0 x 2,9 mDocuments: Chip conveyor: triple signal light: ...
GeneralCNC Turning Centre with C axis and tool drive; Control: CELOS with Siemens 840D sl Operate Working areaSwing diameter over guide ways700 mmTurning diameter410 mmTransverse stroke300 mmLongitudinal stroke850 mmMax. Turning Length800 mmClamping chuck diameter max.315 mmBar diameter max.65 mmWork spindle (left)Spindle noseFlat flange Spindle bore87 mmDiametre of spindle nose170h5 mmSpindle diametre on front bearing130 mmTool holder 1Number of tool stations12 Shank diametre according to DIN 6988040 mmNumber of driven tools12 Speed max.-6000 rpmPower max. (40% DC)10 kWMain drive 1Drive power (100% DC)25 kWTorque (100% DC)280 NmSpeed range25 - 5000 rpmAccuracy at point stopping0,01 degreeFloor space/WeightDimensions (L x W x H)3,99 x 2,69 x 1,99 mWeight approx.6500 KgTechnologie cycle alternating speedTechnology cycle for the application of an alternating speed for vibration sensitive s ...
GeneralCNC Turning Centre; Control: CELOS with Siemens 840D sl Operate Working areaSwing diameter over guide ways620 mmTransverse stroke260 mmLongitudinal stroke795 mmClamping chuck diameter max.315 mmWork spindle (left)Spindle bore91 mmSpindle diametre on front bearing140 mmMain drive 1Drive power (100% DC)22 kWSpeed range- 4000 rpmMax. torque (40% DC)525 NmTorque (100% DC)410 NmAccuracy at point stopping0,001 degreeTool holder 1Number of tool stations12 Shank diametre according to DIN 6988040 mmNumber of driven tools12 Speed max.-6000 rpmPower max. (100% DC)10 kWFloor space/WeightDimensions (L x W x H)3,99 x 2,03 x 2,2 mWeight approx.6500 KgTechnologie cycle alternating speedTechnology cycle for the application of an alternating speed for vibration sensitive set-ups (Only in conjunction with Siemens control)Y-Axis PartingTechnology cycle to parting off the workpiece by the Y-axis to a ...
GeneralMilling Specification; Control: Control M730UM with CELOS CharacteristicsMax machining diameter278 mmDimensions (L x W x H)2,82 x 2,09 x 2,15 mDrive power tool spindle5,5/5,5/3,7 kWDrive power main spindle11/15/15 kWRapid feed X / Z30/30 m/minInput precision of C-axis on Mainspindle0,001 degreeRotary tool spindle speed10000 rpmMovements X / Z260/590 mmNumber of tool stations12 Speed max.6000 rpmBar diameter max.52 mmSwing- Ø, max.755 mmMax. Turning Length192 mmWeight approx.4900 KgCELOS - ERGOline TouchCELOS - ERGOline Touch to facilitate machine operation incl. 21.5 ERGOline Touch ® control with multi touch screens Uniform management, documentation and visualization of order, process - and machine data Networkable with CAD / CAM User friendly and pHigh-output spindle (Left Spindle) 15/ 11 kW, 6,000 min-1(Left Spindle) High-Output Spindle 15/11 kW (20/15 HP), 6,000 min-1 The N ...
GeneralCNC Turning Centre with C axis and tool drive; Control: CELOS with Siemens 840D sl Operate Working areaSwing diameter over guide ways700 mmTurning diameter410 mmTransverse stroke300 mmLongitudinal stroke850 mmMax. Turning Length800 mmClamping chuck diameter max.315 mmBar diameter max.65 mmWork spindle (left)Spindle noseFlat flange Diametre of spindle nose170h5 mmSpindle bore87 mmSpindle diametre on front bearing130 mmMain drive 1Drive power (100% DC)25 kWSpeed range25 - 5000 rpmTorque (100% DC)280 NmC-Axis Speed-200 rpmTorque of C-Axis (holding torque)225 NmAccuracy at point stopping0,01 degreeTool holder 1Number of tool stations12 Shank diametre according to DIN 6988040 mmNumber of driven tools12 Speed max.-4000 rpmPower max. (40% DC)11,3 kWFloor space/WeightDimensions (L x W x H)3,99 x 2,69 x 1,99 mWeight approx.6500 KgTechnologie cycle alternating speedTechnology cycle for the ...
GeneralCNC Turning Centre with C axis and tool drive; Control: CELOS with Siemens 840D sl Operate Working areaSwing diameter over guide ways700 mmTurning diameter410 mmTransverse stroke300 mmLongitudinal stroke850 mmMax. Turning Length800 mmClamping chuck diameter max.315 mmBar diameter max.65 mmWork spindle (left)Spindle noseFlat flange Diametre of spindle nose220h5 mmSpindle diametre on front bearing160 mmSpindle bore102 mmMain drive 1Drive power (100% DC)33 kWSpeed range20 - 4000 rpmTorque (100% DC)580 NmC-Axis Speed-200 rpmTorque of C-Axis (holding torque)580 NmAccuracy at point stopping0,01 degreeTool holder 1Number of tool stations12 Shank diametre according to DIN 6988040 mmNumber of driven tools12 Speed max.-6000 rpmPower max. (40% DC)10 kWFloor space/WeightDimensions (L x W x H)3,99 x 2,69 x 1,99 mWeight approx.6500 KgTechnologie cycle alternating speedTechnology cycle for the a ...
GeneralCNC Turning Centre with C axis and tool drive; Control: CELOS with Siemens 840D sl Operate Working areaSwing diameter over guide ways700 mmTurning diameter410 mmLongitudinal stroke850 mmTransverse stroke300 mmMax. Turning Length800 mmClamping chuck diameter max.315 mmBar diameter max.65 mmWork spindle (left)Spindle noseFlat flange Diametre of spindle nose170h5 mmSpindle diametre on front bearing130 mmSpindle bore87 mmMain drive 1Drive power (100% DC)33 kWSpeed range20 - 4000 rpmTorque (100% DC)580 NmC-Axis Speed-200 rpmTorque of C-Axis (holding torque)225 NmAccuracy at point stopping0,01 degreeTool holder 1Number of tool stations12 Shank diametre according to DIN 6988040 mmNumber of driven tools12 Speed max.-4000 rpmPower max. (40% DC)11,3 kWFloor space/WeightDimensions (L x W x H)3,99 x 2,69 x 1,99 mWeight approx.6500 KgTechnologie cycle alternating speedTechnology cycle for the ...
GeneralCNC Turning Centre with C axis and tool drive; Control: CELOS with Siemens 840D sl Operate Working areaSwing diameter over guide ways700 mmTurning diameter410 mmTransverse stroke300 mmLongitudinal stroke850 mmMax. Turning Length800 mmClamping chuck diameter max.315 mmBar diameter max.65 mmWork spindle (left)Spindle noseFlat flange Diametre of spindle nose170h5 mmSpindle bore87 mmSpindle diametre on front bearing130 mmMain drive 1Drive power (100% DC)25 kWSpeed range25 - 5000 rpmTorque (100% DC)280 NmC-Axis Speed-200 rpmTorque of C-Axis (holding torque)225 NmAccuracy at point stopping0,01 degreeTool holder 1Number of tool stations12 Shank diametre according to DIN 6988040 mmNumber of driven tools12 Speed max.-4000 rpmPower max. (40% DC)11,3 kWFloor space/WeightDimensions (L x W x H)4,46 x 1,88 x 2,30 mWeight approx.6500 KgTechnologie cycle alternating speedTechnology cycle for the ...
x-travel: 2.600 mmy-travel: 700 mmz-travel: 700 mmControl: SIEMENS SINUMERIC 840D table-size: 2.900x700 mmtable weight: 2.150 Kgtool adaptor: SK 40 DIN 69872 workpiece length - max.: 300 mmworkpiece weight: 6 kgworkpiece dia.: 80/130 mm: 30 fachmain drive: 18,4/14 kWspeed: 14.000 mm/minrapid traverse: 40 m/minfeed: 40 m/minMachine on: 18.859 hSpindle hours: 5.666 hinternal coolant system feed: 40 Bar/600 l Chip coveyor: inkl. total power requirement: 55 kWweight of the machine ca.: 14.520 kgdimensions of the machine ca.: 10.280 x 7.230 x 3.042 mmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
The Röders RFM 1000/2 is a high-precision vertical machining center designed for intricate milling tasks. Below are its key technical specifications: Travel Distances: X-Axis: 1,000 mm Y-Axis: 800 mm Z-Axis: 600 mm Table Specifications: Dimensions: 1,200 mm x 1,000 mm Maximum Load Capacity: 2,000 kg Spindle Details: Speed Range: 100 to 36,000 rpm Power: 17 kW Sortware update :2019 Find more here - / Contact us at -
Horizontal machining center, 6 pallets, Priced to sell - dismantled and loaded into truck, OKUMA MA40 HA 6P OSP U100M CNC 6 pallets 400mm x 400mm max 400 kgs max workpiece dimensions 600710 Spindle BT40 / coolant through the spindle 4th axis 1° Tool changer: 100 pos. X = 560mm, Y = 610mm, Z = 560mm 40 m/min under power Mimu Machine Tools (Italy), X: 560, pallet: 6, Pallet size: 400400
spindle turning speed - stepless: 26 - 1650 U/minvoltage: 380 V0: 50 Hzrated current: 15 Aconnected load: 6,5 kWtool taper: MK 4 weight of the machine ca.: 2,3 tdimensions of the machine ca.: 1500 x 1200 x 2500 mmOperating voltage: 380 VFrequency: 50 HzControl voltage: 220 VRated current: 15 AConnection: 6.5 kWAutomatic feed: 0.05 - 0.45 mm/revColumn lifting speed: 40 mm/sColumn stroke: 450 mmDrilling spindle stroke: 200 mmDrilling zone: 430 - 1150 mmHeight adjustment of the drilling spindle: 330 - 780 mmTool holder: MK 4Table dimensions: 1525 x 560 mmTable height: 800 mmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
HAAS VF-0 Vertical Machining Center YOM 1998 Table 660x356 mm X/Y/Z 508/406/508 mm Spindle speed 0-7500rpm Spindle motor 14.9kW Rapid feed rate 18m/min Tool Capacity 20 Max. part weight 340.3 kg Spindle taper BT40 Machine Weight 3175Kg Remark: The machine had worked small parts in the production of hunting and sporting rifles. Mechanically OK, Defective a cirquit board
Control Heidenhain ... TNC 530 Clamping table surface... 600mm Axis X ... 800mm Axis Y ... 700mm Axis Z ... 610mm Spindle speed ... 20-15000 rpm controlled axes ... 5 cooling ... 20bar ISO 40 Max. workpiece weight ... 300kg Main engine power ... 25kW Rapid traverse ... 32,32,16m/min Number of positions in the tool changer... 30 Machine weight ... 8750kg L x W x H ... 3710x2530x3230mm
heavy 40s Gillardon with cross table
Drilling capacity steel/GG: 15 mm Spindle holder: 1 MK Projection: 300 mm Table size: 210 x 300 mm Quill stroke: 110 mm Spindle speeds: 200 - 3000 rpm Drive motor: 380 V, 1.1 kW Space requirement: 850 x 420 x 1860 mm Weight: 220 kg
Vertical machining center, CHIRON FZ08KW, 2 pallet, 15000 RPM, HSK40A, CNC Fanuc 21iM, The machine is visible in our warehouse in Gussago BS. M i m u Machine Tools Gussago BS Italy The machining center is a machine tool equipped with a numerical control capable of performing multiple mechanical operations with a single set-up on multiple surfaces of the same work piece. It is generally equipped with several motion axles and one automatic tool exchange system and sometimes multiple pallets
STAMA MC325 / S 2-palllet Double fourth axes Spindle 9000 rpm / 36 tools priced to sell low price - good deal The machine is visible in our warehouse in Gussago BS., Mimu Machine Tools, Gussago BS Italy, The machining center is a machine tool equipped with a numerical control capable of performing multiple mechanical operations, with a single set-up on multiple surfaces of the same work piece. It is generally equipped with several motion axles and one, automatic tool exchange system and sometimes multiple pallets, CNC type: Siemens, Fourth axis: 2 + 2, Number of pallets: 2, Spindle speed RPM: 9000
Key data: 50 mm, 800 1/min
Speeds infinitely variable from 40 - 800 rpm 4 drill feeds . Clearly good original condition
Control: Heidenhain iTNC 530 Travel: X-axis F/H: 3,220 / 2,600 mm Y-axis 800 mm + 65 mm Z-axis F/H 850 / 1,000 mm T-slots 7 pieces Mount: SK 40 Tool magazine: 100 – compartment Spindle speed: 50 - 12,000 rpm Equipment - Internal cooling (IKZ) 20 bar - Belt filter coolant 1250 l -Conveyor - Laser Tool Control System TM200 - Rinsing gun - Electrostatic exhaust air filters - Electronic handwheel -Partition - 2x LTA suction - Prepared for 5th axle
Key data: 835 mm, 510 mm, 510 mm
Fully Functional CNC Milling Machine Machining Center Vertical DMG DMC 835 V Year of construction 2006 Control: SINUMERIK 840 D Powerline Spindle speed: 12,000 rpm Spindle motor: 14 kW X - Travel: 835 mm Y - Travel: 510 mm Z - Travel: 510 mm A-axis: available Rapid traverse: 30 m/min Tool holder: SK 40 Tool changing device: 30 Table load: 800 kg Clamping area: 1,000 x 560 mm Operating hours: 49,660 | 12,902 h (30.01.2025) Footprint of the machine: 2,100 x 2,700 mm Machine weight: approx. 4,200 kg Equipment SIEMENS 840D ShopMill Linear scales Electronic handwheel IKM – 25 bar / 30 l/min Conveyor Canopy Location of the machine: 76661 Philippsburg The machine can be viewed on site at any time. This is always desired. We would love to hear from you.
