Manufacturer:
(Category: 209)
Fixed side at the leftPanel thickness min/max: 16/45 mmMin. panel width: 150 mmLateral panel support for panel width up to 900 mmMin/max. panel length: 700 / 3100 mmMax. laminate overhang: 110 mmMax. laminate thickness: 0,8 mmRadius min/max: 6 / 22 mm (depends the laminate)Feedspeed max. 18 m/minTop pressure by beltEquipment:Infeed fence, adjustable, defines the panel overhang2 x trimming unit 0,4 kW, HSK 25 toolholder1 x PVAc glue application5 x glue nozzle, adjustable1 x hot air blower3 x IR heating on top (55 cm length), 3 x bottom (90 cm length)Postforming zone 1,8 m. lengthVarious pre-installed profiling sets 1 x top trimmer 0,4 kW
Max working width: 1300mmMax working thickness: 140mmMax. machining width: 1300mmMotorized feed rollers2 brushing units
machine 1:Fixed side at the left, working width 220 mm to 2500 mmWorkpiece overhang max. 110 mmElectronic width adjustmentPanel thickness 8 - 90 mmTop pressure by beltsRolling chain with automatic lubrication, automatic pop-up dogs every 1000 mmFeed speed 10 - 40 m/minChain infeed taking 1,62 m. panels in front of the dogsPanel alignment at the infeedMiddle supportNC 30 controllsEquipment left and right:1+1 Jump universal shaper 6 kW1+1 Twin hogging unit, motors 6,6 kW (2 motors)1+1 Universal shaper 6 kW1+1 Jump universal shaper 6 kWpanel turning device HOMAG TD 31/30/13Year 1989machine 2:Fixed side at the left, working width 220 mm to 3000 mmWorkpiece overhang max. 110 mmElectronic width adjustmentPanel thickness 8 - 90 mmTop pressure by beltsRolling chain with automatic lubrication, automatic pop-up dogs every 1000 mmFeed speed 8 - 40 m/minChain infeed taking 1,62 m. panels in front of ...
Workpiece thickness: 8 - 50 mmEdge thickness: Coil edges 0.4 - 3 mmFeed speed 10 m/minEquipment:manual height adjustment.Joint milling unit, 2 motors Panel edge heatingGluing area Pressure zone 1 driven and 2 non-driven rollersEnd trims, 2 x 0,8 kW motors, straight and chamfer 15?Top and bottom trimmingProfile scraping unit for PVC edgingGlue scrapers
Min./max. thickness edge banding on roll: 0,4 - 3mmMin./max. thickness edge banding in strips: 5 mmMin./max. panel thickness: 8 - 50mmMin. panel length/width: 190/110mmThroughput speed: 9m/minPre-milling unit: 2,2kW 7200 rpmSprayers release agentPanel heating device Automatic laoding for edgesGluing unit: 0,18kWEnd-cutting unit with radius: 0,19kWTrimming unit: 2x 0,35kW, 12000rpmRounding unit up to 3mm: 0,35kWEdge scraping unitSprayers cleaning agentGlue scraping unitBrushing unit
Motorised height-adjustmentSound enclosure over all trimming motorsEquipment:Coil and strip magazineHot melt unit Pressure zone End trims, chamfer and straight, automatic adjustmentTop/bottom rough trimmingTop/bottom fine trimming, tilting, Contour trimming unitScraping unitBuffing unitreturn conveyor Ligmatech ZHR 05
Fixed side at the leftFeedspeed 18 - 25 m/minWorking width min 60mm for panel thickness 22mm, 105mm for panel thickness 40mmPanel overhang 30mmPanel thickness 8 - 60 mm in stead of 12 - 40 mm (with limitations)Coil edge thickness: 0,3 - 3 mm, strips 0,4 - 20 mmCoil diameter 830 mmEquipment:Sprayers release agentSquaring device with 2 motors each 3 kWEdge heatingEdge magazine for 2 coils, guillotine for edges up to 3 mmGlueing part A20 with quickmelt applicationLateral pressure zone K, 1 driven and 6 after pressing rollersEnd trims HL84, 2 motors each 0,8kW Rough trimming, 2 motors 1,5kWContour trimming, 2 exchange unitsProfile scraping PN10Flat scrapers FA11Sprayers cleaning agentBuffingAutomation package straight/chamfer:-Automatic adjustment infeed fence-Automatic setting of pressure rollers-Pneumatic setting of end trims-Pneumatic setting of rough trims-Automatic setting of chamfer/ra ...
Workpiece thickness: 8 - 90 mm, electronically adjustableFeed rate: 18-32 m/min frequency controlledEdge thickness: 0.3 - 3 mm for roll edges, strips up to 20 mmEquipment:Inlet guide automatically adjustable via the control, extension 500 mmJoint milling unit: 2 x 3.0 KWworkpiece preheatingGluing unit A34edging magazine for rollPressure zone with 1 driven, 6 non-driven rollers, automatic adjustment from the controlCutting unit WK14, straight, 2 motors 0.8 kWPre-milling unit: 2 x 1.5 KW, pneumatic adjustmentForm milling unit FF 12 automatic, 2 motors 0.4 kWradius/phase milling unit FF12 automatic 4 motors 0.4 KWuniversal milling aggregate controlled UF11, 4 kWProfile scrapers PN20Glue scrapersNozzles for detergent and anti-stickPolishing unitControl: Power Control PC22
Single sided edge bander with hot melt, fixed side at the right, pre-milling unitEdge thickness: 0,4 to 12 mmWorkpiece thickness: 8 - 60 mmFeedspeed 8-20 m/min (limited to 10 m/min using the contour trimming)Workpiece transport by chain, top pressures with rubber rollersSound enclosure over all trimming motorsEquipment:Adjustable fencePre-milling with 2 shapers, each 2,2 kWCoil and strip magazine Hot melt unit, Quickmelt type Pressure zone with1 driven and 2 non-driven pneum. Loaded rollersEnd trims, 2 x 0,35 kW motors, straight and chamfer 15?Top/bottom trimming, motors 2 x 0,35 kWRadius trimmmingContour trimming unit, leading and following edge, 2 x 0,35 kWRadius scraping unitGlue scrapersBuffing unitControlls PC 20+
Machine for cutting, milling, drilling and dowelling frames or rails, straight or mitre, with or without counter profiles in small batch size or one-off productionWorkpiece length 160 - 2350 mm.Workpiece width:- 20 - 140 mm for 2 workpieces per field- 20 - 100 mm for 2 workpieces per field at 45 ?- 20 - 300 mm for 1 workpiece per fieldWorkpiece thickness 10 - 30 mm.Angle adjustable between 45 ? and 90 ?Tables can be tilted 25 ?PC controlled on 3 axesDrilling and inserting on point-to-point basisEquipment:Sawing station: saw blade 350 x 30 mm, motor 2.2 kW, 2800 R / minDrilling station: drill bit diameter 10 mm, motor 2 kWMilling station: diameter tool 100 - 200 mm, spindle diameter 40 mm, clamping length 70 mm, motor 3 kW, 6000 - 12000 R / minDowelling station: dowel dimensions 8 x 30 mm, 8 x 20 mm
Machine designed for machining solid wood doors with frame and raised panelsWorkpiece dimensions Length 150 - 3000 mm Width 40 - 300 mm Thickness 20 - 60 mm Material: hard woods/soft woods Machine equiped with 2 working areas, including - 3 NC-axes X, Y, Z- telephone modem- 1 sawing unit- 1 horizontal boring unit- distance horizontal drill above table (Z):max. 40 mm- fixed workpiece table- central lubrication- CE package- max. workpiece length 2.400 mm KOCH Numeric with 3 NC-axes Positioning control with PC Pentium CPU Operating system Windows XP Professional: english 15? Touchpanel VGA + Touchscreen by means of LVDS connection USB-connection on PC and on Touchpanel Seriel and parallel interface on the PC Hard disk 2,5? Input of machine commands and motor control through the Touchpanel PS2 connection for external keyboard Office PC software Stretched machine bas for max. workpiece width ...
Workpiece sizes: Length 180 - 2500 mm, width 150 - 800 mm, thickness 12 - 40 mmFixed side at the left, motorised width adjustment of the right side Working height/ transport height: 920 mmWorkpiecetransport with belts, infeed belts can lift upVariable feed speedEach side has got 5 glue injectors and 8 dowel inserters (Type 34)Doweldiameter: 8 mm, dowellength 30 mm, dowelprojection 7-14 mm, dowelcenters min. 32 mm, max. 736 mmEach side with dowel hopper feed with shaker and separatorsControll mirrorGlue pump 1:1 Glue injection controlls type ELC
X=3700mm Y=1440mm, Z=150mmMoving speed: X: 80 m/min, Y: 80 m/min, Z: 20 m/min8 supports with vacuum cups, pneumatic clamping8 fences at the rear8 fences in front2 left fences and 2 right fences6 rails for panel loading with pneumatic liftingPositioning the vacuum cups using a laser1 connection for templatesVacuum pump with flow rate 100 m3/hConfiguration V25,H8X/6Y, N1 X-Y 90?, F1-HSK63-15KW,F1-HSK63-9KW, C axis, W14 rearMain motor 15 kW, 1250-24000 rpm, air-cooled, 360? C-axis, C-axis interpolation axis, HSK 63 mountingC axis extension for flex-5 aggregateMain motor 9 kW, 1250-24000 rpm, air cooled, HSK 63 mountingTool changer operating in X direction with 14 positions, rear mounted2 x 4 vertical X drilling pins, 2 x 3 vertical Y drilling pins14 horizontal drilling spindles90? groove saw X-Y directionPC 85 power control software with:Woodwop: workshop-oriented programming systemImport 2 ...
Single sided postforming line, capable of doing L - and U profiles, with or without insert.Workpiece thickness: 16 to 60 mm.Min. workpiece width: 150 mm.Workpiece overhang: 70 mm.Max. laminate overhang: 105 mm.Feed speed 3 - 18 m/min.Fence side at the leftEquipment:Squaring and shaping part:1 x Postforming squaring unit, 2 motors each 1kW, 1st motor removing the laminate, 2nd motor trimming the overhaning laminate1 x scoring, motor 1 kW, top position1 x milling unit for the laminate when doing U profiles 1 x laminate support Postforming part1 x blow cleaning nozzle 6 x glue nozzle for the glue application 2 x glue roller9 x IR heating, each 2,2 kW2 x Hot air blower, each 10 kW1 x Basic postforming pressure zone for L-profiles, using rollers1 x Basic postforming pressure zone for U-profiles, using rollers1 x VF postforming pressure zone for special profiles, using pressure pathsFinishing ...
Machining center in vertical designWorkpiece dimensions:Length 200 to 3050 mmWidth 70 to 850 mmThickness 12 to 60 mmMax workpiece weight 35 kg1 milling spindle 10 kW (HSK63)with tool changer with 4 positions13 independently callable vertical drilling spindles4 independent horizontal drilling spindles in X2 horizontal drilling spindles in Y1 grooving cutter in XWood WOP operating softwareWood WOP import basicDXF import basicOperating language: nl, de, enWoodwop 7 Office license included
Working field: axis x: 2310 mm, axis y: 628 mm, axis z: 90mmMax programmable speed: axis x: 100 m/min, axis y: 75 m/min, axis z: 15 m/minDrill chuck: diameter 10 mmSpindle speeds: 4000 rpmGrooving saw: diameter 120 mmDrill spindles: 4 horizontal spindles in X,12vertical spindles in X lineWorking air pressure: 6 barMax consumption of compressed air: 0,75 NL/cycleInstalled power: max 7.5 kWCapacity of vacuum tools: 40 m?/hCNC:screen: monochromatic 9?Floppy disk unitPLC for control of the machine cycle
Working field: axis x: 3200 mm, axis y: 944 mm, axis z: 110mmMax programmable speed: axis x: 100 m/min, axis y: 75 m/min, axis z: 15 m/minDrill holder: diameter 10 mmSpindle speeds: 4000 rpmGrooving saw: diameter 120 mmDrill spindles: 24 horizontal spindles in X,10 vertical spindles in X lineWorking pressure air pressure: 6 barInstalled power: max 25 kWCapacity of vacuum tools: 40 m?/hCNC:screen: monochromatic 9?Floppy disk unit
Working area: X 5200 x Y 1260 mmHeading of main spindle: X 5709 mm, Y 1650 mm8 workpiece consolesEquipment:Drilling unit with 18 spindles, 12 vertical sp?ndles, 6 horizontal spindles (4 in direction X , 2 in direction Y )Grooving sawMilling motor 11 kW, 20000 rpm max, HSK-F 63 take-up, liquid-cooled, 5-axis controlledTool changer with 16 positionsLaterally positioned changer with 8 positions PC control
Right-hand versionCutting-off saw: 1.5 kW2 x horizontal shaft: 2 x 1.5 kW1 x vertical shaft, diameter 50 mm, length 160 mm, 2.2 kW
Right-hand versionWorkpiece dimensions: max. length 3000 mm, min. 250 mm, max. thickness 100 mm, min. 30 mm, width 200 mmOverhead cutting saw, 3 kW, 3000 rpm, manual horizontal movement over 120 mm, 400 mm blade, cutting height 100 mm1 vertical shaft, 340 mm long, 40 mm diameter, 7.5 kW, 3100 rpm, suction port with 150 mm diameter (x2), max. tool diameter: 320 mmCarriage with pneumatic clamping1100 x 500 mm tableStop, positioning from -45? to 45?Motorized carriage with electronic control 2-32 m/min
Working width 180 - 3200 mm, electronic setting Sieb & MeyerFixed side at the leftChain transport, 80 mm wideInfeed for panels of about 1 m.Top pressure by driven beltsMax. workpiece thickness: 80 mmFeedspeed 7 - 35 m/min, motor 2,2 kWPop-up dogs every 1m10Equipment left / right:1 st postFront: 1+1 Jump scorer, motor 1,5 kW, 100 Hz, joined to 1+1 Hogger, motor 3 / 4,4 kW, 50/100 HzRear: 1+1 Jump milling, tilting, motor 1,5 kW, 100 Hz2nd postFront: 1+1 Jump milling, tilting, motor 1,5 kW, 100 HzRear: 1+1 Fixed milling, tilting, motor 2,2/3,3 kW, 50/100 Hz3th postFront: 1+0 Jump milling, tilting, motor 2,2/3,3 kW, 50/100 HzRear: 1+1 Jump milling, tilting, motor 1,5 kW, 100 HzAll units with horizontal/vertical adjustment and Siko read-outOutfeed chain approx. 80 cm lengthSound and safety enclosures
Miscellaneous Auction-ID: A1-41272-258
Miscellaneous Auction-ID: A1-41272-256
Miscellaneous Auction-ID: A1-41272-257
including various profile cutters, saw blades, etc Auction-ID: A1-41272-273
Miscellaneous Auction-ID: A1-41272-277
This STEFANI Solutions 86 edgebander was manufactured in 2009. It features Nordson equipment, a maximum glued edge thickness of 25 mm, and a maximum panel thickness of 60 mm. The machine includes electric height adjustment, upper belt pressure, and a preheating zone. It also boasts interchangeable roller storage with 12 positions and a replaceable glue pot. Consider the opportunity to buy this STEFANI Solutions 86 edgebander. Contact us for more information about this machine.
Workbench with all firmly connected parts, e.g. from Carl Steuernagel Kleinmaschinenbau Leipzig General: – Used with traces of use from the estate - Function not checked during the inspection – Scope as seen, without any other accessories – For professional self-dismantling and exclusively by collection – In auction until 17.01.2026
Lead screw lathe on heavy casting frame The machine is equipped with lead screw, cross slide and upper slide and has handwheels on transverse and longitudinal feed. A three-jaw chuck is mounted on the headstock. The drive is provided by an electric motor with V-belt and pulley drive underneath. Technical characteristics (according to nameplates and inspection): - Design: Lead screw lathe on free-standing cast iron frame with shelf - Drive: Electric motor with pulleys, mounted on the side/bottom of the frame - Headstock with pulleys and gear drive - Tailstock with handwheel adjustment - Mechanical longitudinal and transverse feed via lead screw - Several pulleys for speed selection General: – Used with traces of use from the estate - Function not checked during the inspection – Scope as seen, without any other accessories – For professional self-dismantling and exc ...
Vebim
10 € 
