Производитель:
(Категория: 209)
Lindner T500/200-4 — стационарный промышленный древесиноруб, 1979 год, произведённый в Австрии. Основной привод мощностью 90 кВт, 380 В, 50 Гц, электродвигатель с V-образной коробкой передач. Подающий бункер с зубчатыми впускными роликами, тяжёлый ротор ножа против фиксированного контрножа и интегрированная сита для контроля размера щепы. Полностью сварная стальная конструкция для обработки древесины, плит, бордюров и остатков древесины лесопилки. Тяжёлая машина, разработанная для непрерывной раб ...
Поперечный конвейер Pinomatic для строгальной и пильной линии Год постройки 2001 Производитель Pinomtatic OY Тип POS 9+10 Серийный номер P1033 Моторизованный поперечный конвейер с 7 цепными талями Длина кронштейнов: : 6000 мм Ширина поперечного конвейера до 4000 мм (регулируемая ) Высота: 900 мм 6 цепных талей стационарного монтажа 1 цепная таль может регулироваться по-разному Напряжение 230/ 400 В переменного тока
Паллетная гвоздёжная машина Böhm und Kruse Тип 3 20 1250 Максимальная ширина прохода 1250 мм Максимальная высота клиренса 200 мм Минимальное расстояние между ногтями — 45 мм Общая подключённая нагрузка 12 кВт 20 кормилов для гвоздей 2 коробки для гвозде
Number of dust containers: 3 St.: 200 mmoutput: 3,7 kw: 2.950 m³/h: 2.200 paThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
: 2,2 mmoutput: 1,68 kw: 2.800 m³/hThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Radial fan, dust extraction blower, fan, extraction, dust blower, blower, exhaust fan -Dust extraction fan: radial fan -Motor: Loher ENGV-132SB-04M 5.0 kW 1440 rpm Ex protected -Volume flow rate: m³/h -Connection: Inlet Ø 500 mm -Connection: Outlet Ø 500 mm -Fan wheel: Ø 510 x 220 mm -Dimensions: 1000/750/H1630 mm -Weight: 156 kg
Код: 0507 Бренд: SCM MINIMAX - ИТАЛИЯ Модель: CU 350 K - Norme CE Universal 5 Works комбинированная машина для столярных мастерских, ремесленников, мебельщиков, индивидуальных мебельных изделий, дверей, деревянных столярных изделий, DIY, панелей и различных применений — CE Standard Технические данные: Основание состоит из одного полностью сварного стального моноблока Чугунный рабочий стол Широкая площадь рабочего стола Трёхфазные двигатели мощностью 380/50 л.с. каждый Поверхностный строгалка: Рабочая шири ...
Производитель: Fravol Модель No: M200-23 Год: 2021 Состояние: Использовано Номер наличия: 9627 Толщина кромки: 12-45 мм Толщина детали: 10-45 мм Минимум. Длина материала: 120 мм Минимум. Ширина материала: 80 мм Вес: 1000 к
Klöckner TH 240 x 650 L-4WV стационарный промышленный дробильщик древесины, 2000 год. Подходит для переработки остатков древесины, плит, отходов и производственных отходов в древесную щепу. Включает шкаф управления и запасные части. Полная система утилизации остатков древесины с скребком, вибрирующим парашобом и конвейером доступна по запросу. Конструкция с тяжёлой сталью и ленточный привод для бесперебойной работы на лесопилках и биомассовых заводах. Последний сервис 2025 года, капитальный ремон ...
A CMS CNC woodworking center is available. Axes: 5, travel X/Y/Z: 3500mm/2200mm/300mm, spindle power: 15kW, speed: 24000rpm, tool holder: HSK-F63, tool places: 20, table type: matrix vacuum table, control: Osai S10. The system control was modernized in 2006. Documentation available. On-site inspection is possible.
A Trima CNC gantry machining center is available. Workpiece dimensions X/Y/Z: 2500mm/1100mm/80mm, spindle power: 7.5kW, speed: 24000rpm, tool positions: 10, traversing speed X/Y/Z: 55m/35m/15m/min. Machine dimensions X/Y: approx. 4400mm/2500mm, weight: approx. 3200kg, control: Siemens Sinumerik. The machine has a control defect. The reference run is aborted. Documentation available. On-site inspection is possible.
Митровый пунш Morsoe, в хорошем состоянии, сразу доступен. Если вы заинтересованы, мы также с радостью расскажем вам о других машинах нашей компании. Вы можете посетить машину в нашем доме по предварительной записи.
Feed speed: 18-25m/min, with FK11 max. 20m/min, working height: approx. 950mm, max. workpiece thickness: 60mm, edge banding material rolls: approx. 0.3-3mm, edge banding material strips: approx. 0.4-6mm, max. roll diameter: 830mm, machine length: approx. 7845mm, operating hours: 25724h, feed operating hours: 3371h, machining time: 412h, control system: HOMAG powerControl PC22. Annual production: between 15000 and 22000 linear meters per year. Equipment: Top/bottom release agent spraying unit, joint trimming unit, glue application unit, 2-roll edge banding magazine, pressure zone, end trimming unit HL81, pre-milling unit BF10, profile trimming unit FK11, profile scraper PN10, finishing unit with glue joint scraper and buffing unit, preparation for HOMAG laserTec, powerControl PC22 with touchscreen, automation packages. In addition, scrapers for both 2mm and 1mm edges are available. Equipm ...
Drum crusher with hydraulic pusherKnife drum width: 800 mmMouth 800 x 1200 mmMotor: 18,5 kWextraction connection diameter 200 mm
Max working width: 1300mmMax working thickness: 140mmMax. machining width: 1300mmMotorized feed rollers2 brushing units
Workpiece thickness: 8 - 50 mmEdge thickness: Coil edges 0.4 - 3 mmFeed speed 10 m/minEquipment:manual height adjustment.Joint milling unit, 2 motors Panel edge heatingGluing area Pressure zone 1 driven and 2 non-driven rollersEnd trims, 2 x 0,8 kW motors, straight and chamfer 15°Top and bottom trimmingProfile scraping unit for PVC edgingGlue scrapers
Panel thickness: 8 - 50 mmThickness of the edges: 0,4- 3 mmFeed speed 8 - 11 m / minPU pressure rollersEquipment:Squaring unit, 2 motors 2,2 kWPanel edge heatingEdge magazine for coil and stripsHot melt application with rollerAirtec AT4510 unitThe Airtec aggregate is positioned so you can use Airtec or the standard glue potMotorized side pressure unitEnd trims, 2 motors, pneumatic positioning straight and with chamfertrimming unit above / belowContour trimming unitProfile scraping unitGlue scraping unitPolishing unitDetergent spray systemcentral lubrication
Fixed side at the leftFeedspeed 18 - 25 m/minWorking width min 60mm for panel thickness 22mm, 105mm for panel thickness 40mmPanel overhang 30mmPanel thickness 8 - 60 mm in stead of 12 - 40 mm (with limitations)Coil edge thickness: 0,3 - 3 mm, strips 0,4 - 20 mmCoil diameter 830 mmEquipment:Sprayers release agentSquaring device with 2 motors each 3 kWEdge heatingEdge magazine for 2 coils, guillotine for edges up to 3 mmGlueing part A20 with quickmelt applicationLateral pressure zone K, 1 driven and 6 after pressing rollersEnd trims HL84, 2 motors each 0,8kW Rough trimming, 2 motors 1,5kWContour trimming, 2 exchange unitsProfile scraping PN10Flat scrapers FA11Sprayers cleaning agentBuffingAutomation package straight/chamfer:-Automatic adjustment infeed fence-Automatic setting of pressure rollers-Pneumatic setting of end trims-Pneumatic setting of rough trims-Automatic setting of chamfer/ra ...
Single sided edge bander with hot melt, fixed side at the right, pre-milling unitEdge thickness: 0,4 to 12 mmWorkpiece thickness: 8 - 60 mmFeedspeed 8-20 m/min (limited to 10 m/min using the contour trimming)Workpiece transport by chain, top pressures with rubber rollersSound enclosure over all trimming motorsEquipment:Adjustable fencePre-milling with 2 shapers, each 2,2 kWCoil and strip magazine Hot melt unit, Quickmelt type Pressure zone with1 driven and 2 non-driven pneum. Loaded rollersEnd trims, 2 x 0,35 kW motors, straight and chamfer 15°Top/bottom trimming, motors 2 x 0,35 kWRadius trimmmingContour trimming unit, leading and following edge, 2 x 0,35 kWRadius scraping unitGlue scrapersBuffing unitControlls PC 20+
Workpiece thickness: 8 - 90 mm, electronically adjustableFeed rate: 18-32 m/min frequency controlledEdge thickness: 0.3 - 3 mm for roll edges, strips up to 20 mmEquipment:Inlet guide automatically adjustable via the control, extension 500 mmJoint milling unit: 2 x 3.0 KWworkpiece preheatingGluing unit A34edging magazine for rollPressure zone with 1 driven, 6 non-driven rollers, automatic adjustment from the controlCutting unit WK14, straight, 2 motors 0.8 kWPre-milling unit: 2 x 1.5 KW, pneumatic adjustmentForm milling unit FF 12 automatic, 2 motors 0.4 kWradius/phase milling unit FF12 automatic 4 motors 0.4 KWuniversal milling aggregate controlled UF11, 4 kWProfile scrapers PN20Glue scrapersNozzles for detergent and anti-stickPolishing unitControl: Power Control PC22
Fixed side at the leftFeedspeed 18 - 25 m/minWorking width min 60mm for panel thickness 22mm, 105mm for panel thickness 40mmPanel overhang 30mmPanel thickness 8 - 60 mm in stead of 12 - 40 mm (with limitations)Coil edge thickness: 0,3 - 3 mm, strips 0,4 - 20 mmCoil diameter 830 mmEquipment:Sprayers release agentSquaring device with 2 motors each 3 kWEdge heatingEdge magazine for 2 coils, guillotine for edges up to 3 mmGlueing part A20 with quickmelt applicationLateral pressure zone K, 1 driven and 6 after pressing rollersEnd trims HL84, 2 motors each 0,8kW Rough trimming, 2 motors 1,5kWContour trimming, 2 exchange unitsProfile scraping PN10Flat scrapers FA11Sprayers cleaning agentBuffingAutomation package straight/chamfer:-Automatic adjustment infeed fence-Automatic setting of pressure rollers-Pneumatic setting of end trims-Pneumatic setting of rough trims-Automatic setting of chamfer/ra ...
Fixed side at the leftPanel thickness min/max: 16/45 mmMin. panel width: 150 mmLateral panel support for panel width up to 900 mmMin/max. panel length: 700 / 3100 mmMax. laminate overhang: 110 mmMax. laminate thickness: 0,8 mmRadius min/max: 6 / 22 mm (depends the laminate)Feedspeed max. 18 m/minTop pressure by beltEquipment:Infeed fence, adjustable, defines the panel overhang2 x trimming unit 0,4 kW, HSK 25 toolholder1 x PVAc glue application5 x glue nozzle, adjustable1 x hot air blower3 x IR heating on top (55 cm length), 3 x bottom (90 cm length)Postforming zone 1,8 m. lengthVarious pre-installed profiling sets 1 x top trimmer 0,4 kW
Machining center in vertical design with automatic returnWorkpiece dimensions:Length: 200 to 3050 mmWidth: 50 to 1250 mmThickness: 8 to 80 mmweight max 60 kgPerformance- 2x vertical drilling unit separately controllable with variable speed. right left V10/32mm. 2.3 kW. Drill length 70 mm, D= max 35 mm- 2x horizontal drilling unit, 6 spindles in X direction, variable speed. right left can be controlled separately. Drill length 70 mm, D= max 20 mm- 2x horizontal drilling unit, 2 spindles in Y direction, variable speed. right left can be controlled separately. Drill length 70 mm, D= max 20 mm- Grooving saw unit X-Y can be swiveled 0°/90° saw diameter 125 mm, rpm 1500-7500 frequency controlled- Dowel insertion station for automatic insertion of dowels on the two transverse workpiece edges 1x left side / 1x right side glue pump, vibrating guide for dowels 8 x 35/40 mm- plausib ...
4-axis machining centerworking area: X Y Z : 3060 x 1080 x 155 mmMovement speed X 100 m/min, Y 100 m/min, Z 30 m/min14 vertical spindles4 horizontal spindles in X direction2 horizontal spindles in Y directionGrooving saw 0° - 90°toolchanger 7 positionstoolchanger 10 positionsRouter 7,5 kW, ISO 30 , 1000 - 24000 r/min, c-axislock milling aggregate available in option
Gantry-type, 3-axis CNC machining centreWorking area (type 2132): approx. 3300 x 2100 mmVacuum table with multiple switchable zonesInput: AES lifting table for automatic sheet loadingOutput: conveyor belt with label printer (labels are printed and applied manually)Main spindle: HSD ES929, HSK-F63 mount, 7.5 kW (9 kW), speed up to 24,000 rpm, 800 Hz, 380 VMain spindle overhauled in 2023Drilling unit with 16 spindles: 6 vertical spindles in X, 4 vertical spindles in Y, 2 double horizontal spindles in X, 1 double horizontal spindle in YSlotting sawTool changer with 12 positionsVacuum: Becker vacuum pumps, system approx. 500 m³/hControl: OSAI control system with AES ProcessController, operation via console with touchscreen and keyboardOperating hours: approx. 2,100 h (machine life), main spindle overhauled at approx. 1,360 h
Working area: X 5005 x Y 1520 mm x Z 200 mmMain spindle travel: X 5910 mm, Y 1815 mm, Z 655 mm.Travel speed: X 80 m/min, Y 80 m/min, Z 25 m/min8 workpiece consoles with automatically positioning vacuum cupsEquipment:Drilling unit with 19 spindles, 7 vertical spindles in X, 6 vertical spindles in Y, 2 double horizontal spindles in X, 1 double horizontal spindle in Y Slotting sawMilling motor 12 kW, 1000–24,000 rpm, HSK-F 63 mounting, liquid-cooled, 5-axis controlledTool changer with 22 positions Vacuum pumps with 2 x 100 m³/h capacityPC controlMasterwork software Integrated waste conveyor
Bridge type Capacity for all units: 3300 x 1100 mm(alternating: 2 x 1025 x 1100 mm)Capacity for routing with tooldiameter 25 mm: 1550 mmWorkpiece thickness up to 300 mm (stroke Z-axis 600 mm)Speed in X and Y: 60 m/min, Z: 25 m/min, Vector: 85 m/min6 Support rails with LED positioning indicationVacuum: 100/140 m3/hControlls: Powercontrol PC85Waste/chip removal belt in machine baseMachine pneumatically prepared to take pneumatic clamps, 3 pcs clamps includedDrilling unit V9/H4, 13 spindles, motor 2,2 kWMain spindle DRIVE5C+, 5-axis, 10 kW, HSKF63 taper, speed 1000 to 24000 r/min, tooldiameter up to 180 mm for routing, 350 mm for cutting14-fold rotary toolchanger and pick-up place for a sawbladeWoodwop software
112 € 
