Manufacturer:
(Category: 102)
Ref. -No.: 10367Manufacturer: WEILERYear of construction: 1996Type of control: CNCControl: SiemensStorage location: HalberstadtCountry of origin: GermanyTurning Speeds: 500 RPMMachine length: 7000 mmMachine width: 2300 mmMachine Height: 2600 mmWeight Of The Machine Ca.: 9,25 tSpindle Taper: 6 Mk Travel quill: 300 mmBed width: 800 mmTurning Length: 3000 mmTurning Diameter Over Bed: 900 mmSwing Diameter Over Bed Slide: 530 mmSpindle Bore: 254 mmSpindle power: 45 kWTailstock - Insertione Into The Sleeve: 140 Ø Max. Workpiece Weight: 5000 kgFurther information:Machine can be inspected under power.
Ref. -No.: 10366Manufacturer: MONFORTSYear of construction: 2000Type of control: CNCControl: EURO TURNStorage location: HalberstadtCountry of origin: DeutschlandMachine length: 5000 mmMachine width: 1970 mmMachine Height: 1800 mmX stroke: 370 mmZ - stroke: 2880 mmChuck diameter: 200/250/315 mmCentre Distance: 3040 mmSpindle Head: DIN 55027 - 8x220 Feed Capacity - Z: 18,9 kNFeed Capacity - X: 11,3 kNRapid Travel Speed X-Axis: 5 m / minRapid Travel Speed Z-Axis: 10 m / minCircumferential diameter over radial slide: 350 mmMax swing diameter: 720/630 mmtravel of the cross slide: 375 mmSpindle head max. passage for violent material: 68 mmSpindle head max. passage for bare material: 70 mmTailstock outside diameter of the quill: 110 mmTailstock maximum quill stroke: 210 mmTailstock inner cone: MK6 TypeFurther information:Additional lubricating oil tank approx. 6l
Ref. -No.: 10365Manufacturer: MONFORTSYear of construction: 1997Type of control: CNCControl: MTC KStorage location: HalberstadtCountry of origin: DeutschlandMachine-No.: 178.05 Machine length: 5200 mmMachine width: 2110 mmMachine Height: 1995 mmWeight Of The Machine Ca.: 6,850 (Ohne Späneförderer und Kühlmittelbehäter) tX stroke: 455 mmZ - stroke: 2850 mmChuck diameter: 315/400/500 mmCentre Distance: 3000 mmSpindle Head: DIN 55027 - 11x290 Feed Capacity - Z: 23,9 kNFeed Capacity - X: 11,3 kNRapid Travel Speed X-Axis: 6,8 m / minRapid Travel Speed Z-Axis: 4 m / minCircumferential diameter over radial slide: 540 mmMax swing diameter: 830 mmtravel of the cross slide: 450 mmSpindle head max. passage for violent material: 88 mmSpindle head max. passage for bare material: 90 mmTailstock outside diameter of the quill: 125 mmTailstock maximum quill stroke: 200 mmTailstock inner cone: MK6 Typ ...
Ref. -No.: 10364Manufacturer: MAZAKYear of construction: 1997Type of control: CNCControl: MAZATROL T PLUSStorage location: HalberstadtCountry of origin: JapanMachine length: 6365 mmMachine width: 3180 mmMachine Height: 2800 mmWeight Of The Machine Ca.: 7 tBar passage: 64 mmMax rotation diameter: 510 mmTurning Diameter: 400 mmTurning Length: 1539 mmSpindle power: 22-26 kWSpindle Speed Min.: 35 RPMSpindle Speed Max.: 3500 RPMRapid Travel Speed X-Axis: 12 m / minRapid Travel Speed Y-Axis: 10 m / minRapid Travel Speed Z-Axis: 18 m / minMotor power milling spindle: 7,5 kWMax. speed milling head: 15-6000 RPMX-axis travel: 450 mmY-axis travel: +/- 90 mmZ-axis travel: 1539 mmNumber of tools in the chain magazine: 40 (15 + 25) POS Further information:The main spindle was replaced with a new one in Oktober 2019. In the course of this, small spare parts were renewed or reworked.
Ref. -No.: 10362Manufacturer: SCHIESSYear of construction: 2023Type of control: CNCControl: Siemens - Heidenhain - Fanuc (configurable)Storage location: HalberstadtCountry of origin: Germanyfinancing: nach AnfrageSpindle Speed Max.: 3500 RPMPallet diameter: 1600 mmMax. machining diameter: 2000 mmNumber of claw boxes: 4 pcClamping force per claw box: 55 kNNumber of radial T-slots: 8 Max. speed for turning: 140 min-1Max. speed for milling: 5 min-1Max. torque for turning: 27000 NmMax holding power: 36 kNpositioning speed: 3000 mmAdjustment from center to right: 850 mmShift from center to right (head and tool change): 2750 mmAdjustment from center to left: 850 mmMax feed rate: 2000 mm / minMax rapid traverse speed: 20000 mm / minMax. Feed force: 30 kNcross-section: 280 x 240 mmMax. cutting force when turning: 36 kNMax Spindle Torque: 1200 NmPressure: 6 barAir requirement: 20 m³/h
Ref. -No.: 10359Manufacturer: BRINKMANNYear of construction: 2005Type of control: CNCStorage location: HalberstadtCountry of origin: DeutschlandTool holder type: Sauter Werkzeugrevolver Operating hours: 45000 HoursFurther information:Hinged chip conveyorCoolant cleaning with 2 pumpsCooling system1x jaw chuck without cooling mist exhaust system
Ref. -No.: 10319Manufacturer: TAKANGType of control: Digitalanzeige ACU-RiteControl: KonventionellStorage location: HalberstadtCountry of origin: TaiwanWeight Of The Machine Ca.: 1,3 tSwing diameter over bed: 430 mmBed width: 300 mmTip length: 1500 Centre Height: 215 mmBed length: 1600 mm
Ref. -No.: 10320Manufacturer: TOSType of control: Digitalanzeige - MitutoyoControl: KonventionellStorage location: HalberstadtCountry of origin: TschechienTip length: 1500 Centre Height: 280 mmCentre Distance: 750,1000,15000,2000 mmSpindle Bore: 56 mmSwing diameter over bed: 500 mmNumber of speed levels: 18 Circumferential diameter over the support: 320 mmCircumferential diameter over the bed recess: 560 mmBed length relieved from headstock: 300 mmUniversal chuck diameter: 250 mmDiameter of the clamping disc: 500 mmFurther information:Universal center lathe
Ref. -No.: 10317Manufacturer: NOSOTTIType of control: Digitalanzeige - Mini wizardControl: KonventionellStorage location: HalberstadtCountry of origin: ItalyTip length: 3000 Centre Height: 260 mm
Ref. -No.: 10314Manufacturer: PINACHOYear of construction: 2005Type of control: KonventionellStorage location: HalberstadtCountry of origin: SpainTravel quill: 180 mmTurning Diameter: 630 mmTurning Length: 3000 mmTurning Diameter Over Bed: 620 mmCross Movement. (X-Axis): 365 mmTailstock Quill Diameter: 72 mmTurning diameter over cross slide: 880 mm
Ref. -No.: 10313Manufacturer: MONFORTSYear of construction: 2001Type of control: CNCControl: EUROTURNStorage location: HalberstadtCountry of origin: DeutschlandMachine-No.: 164 01 Machine length: 6200 mmMachine width: 2110 mmMachine Height: 1995 mmWeight Of The Machine Ca.: 7,7 tX stroke: 450 mmZ - stroke: 3850 mmChuck diameter: 315/400/500 mmTurning Diameter: 630 mmTurning Length: 3000 mmCentre Distance: 3985 mmSpindle Head: DIN 55027 - 11x290 Feed Capacity - Z: 23,9 kNFeed Capacity - X: 11,3 kNRapid Travel Speed X-Axis: 4 m / minRapid Travel Speed Z-Axis: 5 m / minTailstock Quill Diameter: 125 mmTailstock Quill Stroke: 200 mmSpace requirement: 7500 x 3500 mmCircumferential diameter over radial slide: 540 mm mmspindle taper diameter: 140 mmJaw chuck diameter: 400 mmjaw continuity: 102 mmQuills Morse taper: 6 Max swing diameter: 830 mmtravel of the cross slide: 450 mmSpindle head max. pa ...
Ref. -No.: 10294Manufacturer: SCHNEIDER WERKZEUGMASCHINENYear of construction: 1983Type of control: CNCControl: Siemens Sinumerik 840 DStorage location: HalberstadtCountry of origin: DeutschlandMachine-No.: 27.0175 Weight Of The Machine Ca.: 4 tTurret places: 8 PcsTurning Diameter: 595 mmTurning Length: 3000 mmBezel diameter (inside): 240 - 490 mmFurther information:Tool turret, with 8 holders, with chip conveyor, approx. 300 mm wide,Belt filter system Mayfran, 2 bezels, 1 x for diam. up to 240 mm, 1 x for diam. until about 490 mm
Ref. -No.: 10258Manufacturer: SCHAERERType of control: KonventionellStorage location: HalberstadtCountry of origin: GermanyLining: Forkardt F315 BrandMachine length: 3.800 mmMachine width: 1.300 mmMachine Height: 1.500 mmWeight Of The Machine Ca.: 4 tTool holder type: Multifix Typ C Turning Length: 1.800 mmTurning Diameter Over Bed: 520 mmTurning Diameter Over Slide Rest: 320 mmSpindle Bore: 62 mmBezel diameter (inside): 270 mmHole in the jaw chuck: 84 x 120 mm
Ref. -No.: 10257Manufacturer: HEIDENREICH & HARBECKYear of construction: 1981Type of control: KonventionellStorage location: HalberstadtCountry of origin: DeutschlandMachine-No.: 80-0512-0562 Turning Speeds: 20-2000 RPMMachine length: 2.900 mmMachine width: 1.200 mmMachine Height: 1.800 mmWeight Of The Machine Ca.: 3,5 tTool holder type: Multifix Typ B Turning Length: 1.000 mmTurning Diameter Over Bed: 480 mmTurning Diameter Over Slide Rest: 295 mmBezel diameter (inside): 1 x 145, 1 x 255 mm
Ref. -No.: 10229Manufacturer: GÖPPINGERYear of construction: 1953Type of control: KonventionellControl: N/aStorage location: HalberstadtCountry of origin: DeutschlandMachine length: 4700 mmMachine width: 1450 mmMachine Height: 1300 mmWeight Of The Machine Ca.: 3,1 tSupply voltage: 380 VTurning Length: 3000 mmTurning Diameter Over Bed: 530 mmCentre Distance: 3050 mmSwing Diameter Over Bed Slide: 305 mmSpindle Bore: 58 mmTotal Power Requirement: 5,5 kWCirculation in the crank: 720 mm
Ref. -No.: 10154Manufacturer: HEYLIGENSTAEDTYear of construction: 2014Retrofit: 2015Type of control: CNCControl: SINUMERIK 840D solution lineStorage location: HalberstadtCountry of origin: DeutschlandBed width: 2000 mmFeed rate: 1-5000 mm / minTurning Diameter: 2600 mmTurning Length: 10000 mmCentre Distance: 11500 mmFaceplate Diameter: 2000 mmSpindle Speeds: 0,5 - 36 min-1/20 - 140 min-1 RPMMax. Torque: 120 NmMax. Workpiece Weight: 40000 - 70000 kgTotal Power Requirement: 230 kWCross slide shift (X-axis): 640 mmFurther information:
Ref. -No.: 10036Manufacturer: JOHNFORDYear of construction: 2009Type of control: CNCControl: Fanuc Series 18i-TBStorage location: HalberstadtCountry of origin: TaiwanMachine length: 9800 mmMachine width: 3695 mmMachine Height: 5292 mmWeight Of The Machine Ca.: 32,6 tamount of positions: 12 Bar passage: 165 mmSerial no.: TDF9007 Turning Length: 2000 mmTurning Diameter Over Bed: 1550 mmSwing Diameter Over Bed Slide: 1270 mmLongitudinal Travel (Z-Axis): 2000 mmSpindle Head: A2-15 Spindle Diameter In Front Bearing: 240 mmSpindle Bore: 185 mmSpindle power: 37/30 kWCross Travel: 685 mmSpindle Speeds: 1000 RPMRapid Travel Speed X-Axis: 10 m / minRapid Travel Speed Z-Axis: 12 m / minTool changer: 12 Pcs
turning diameter: 330 mmturning length: 140x130 mmcontrol: turning diameter over slide: 140 mmtravel -x axis: 107 mmtravel -z axis: 230 mmtotal power requirement: kWweight of the machine ca.: tdimensions of the machine ca.: mThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
CNC Vertical Lathe PIETRO CARNAGHI Model AP 140 TMY Year: 2013 Never used Table Diameter: 10000mm Max. swing: 14000mm Max. loading on table: 500t Max RPM: 0.2-35 Turning height: up to 8900mm CNC Siemens 840D Ram size: 600x600mm Ram stroke: 4000mm Milling head power: 100kW Machine is packed in containers and ready for shipment. The machine was assembled by manufacturer, tested, disassembled and shipped to the buyer. And was never installed after that.
turning diameter: 200 mmturning length: 508 mmx-axis: 176 mmz-axis: 520 mmcontrol: Fanuc-Series O-TD total power requirement: kWweight of the machine ca.: 3,2 tdimensions of the machine ca.: 2,73x1,98x1,64 mThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
CNC lathe LB 3000 EX II Manafacture: Okuma Corporation Year of manufacture: 2017 Control OKUMA ... OSP-P300LA Turning diameter ... 580mm Turning length ... 950mm inclined bed Axis Y ... 120mm Spindle bore ... 91mm Tool turret ... 12/12 Axis X ... 260mm Axis Z ... 510mm Spindle speed ... 0-5000 rpm. Rapid traverse of the X axis ... 25m/min Rapid traverse of the Z axis ... 30m/min Rapid traverse of the Y axis ... 12.5m/min Axis C ... 360° Main engine power... 22kW L x W x H ... 3420 x 2041x 2444 mm Machine weight ... 6600kg The machine is in good condition, possible to test under power.
NDT lathe - Böhringer Type VDF 400 Spindle 600-440 mm maximum length 2000mm Tool magazine with 12 tools
turning diameter: 750 mmturning length: 1520 mmcontrol: Fanuc 18 iT-B total power requirement: 22,0 kWweight of the machine ca.: 15,5 tdimensions of the machine ca.: mThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
turning diameter: 300 mmturning length: 2000 mmswing diameter over bed slide: 520 mmtotal power requirement: 7,5 kWweight of the machine ca.: 2,8 tdimensions of the machine ca.: 4745 mm x 1340 mm mThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Key data: 42 mm, 588 mm
bar capacity 42 mm - three x 12 position turrets (3 x Y axis +/- 31 mm) - LNS Sprint S3 new in 2007 with rear magazine - weel tooled - Fanuc 31iTA Control
turning diameter: 330 mmturning length: 510 mmcontrol: FANUC 18i - T turning diameter over bed: 600 mmturning diameter over slide: 550 mmx-travel: 250 mmz - travel: 580 mmy-travel: 100 (±50) mmb-axis: 0.001 mmrapid travel x/y/z: 20/7,5/24/ m/minrapid taverse: B- Achse 20 m/minc-axis: 4.500/ 6.000 °spindle passage: 76/ 45 mmspindle nose: A2#6 spindle turning speed range: 4.500/ 6.00 U/minspindle drive: 15/ 7,5 kWTurret: 12- fach Stationen Chip coveyor: Inkl. chuck: Hauptspindel 210 mmchuck: Subspindel 160 mmtotal power requirement: 50,7 kVAweight of the machine ca.: 4,9 tdimensions of the machine ca.: 3.118 x 1.705 x 2.076 mmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
turning diameter over bed: 1450 mmturning diameter over slide rest: 1070 mmturning length: 7000 mmturning speeds: 2,24-450 U/minControl: faceplate: 1400 mmspindle passage: 160 mmsteady: 400 mmdrive capacity - workpiece: 63 kWTail stock:: elektr. diameter of quill: 200 mmbed width: 950 mmcontrol: Siemens total power requirement: kWweight of the machine ca.: tdimensions of the machine ca.: mThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Ergomat TBC 60 - Multi-slide turning center - as good as new exhibition machine - Rod passage: 60 mm - Tool holder: VDI 25 Compact multi-carriage turning center with eight CNC axes, two-channel control and backside machining. Developed for the ready-to-use production of complex turned parts. - Fanuc 31i-TB dual-channel control - 8 CNC-controlled axes - 2 vertical shaped slides and piercing slides - CNC cross slide at the front - Rear CNC cross slide with servo-driven Sauter turret and driven tools - Tapping spindle integrated in the turret - Astonishingly short cycle times - Backside processing - Coolant device - Generously dimensioned working area for unhindered chip fall - Chip collector - Year of construction: 2021 Specifications: Rod passage: - Round material: 60 mm - Hexagonal material: 52 mm - Square material: 42 mm Main drive: - max. spindle speed: ...
Very well preserved CNC lathe WEISSER Heilbronn, type Gigant. From precision operation, only ultra-fine machining. Details Type Gigant Machine No. 27-0166 hydraulically self-tightening fork art chuck with power clamping cylinder 4x Sauter revolver, size 400 mm2 Siemens SINUMERIK 840D fully functional Commissioning 04/2003 Travels X 725 mm (stroke), Z 1,480 mm Main spindle drive DC 45 kW (nominal power) Speeds in 3 stages up to max. 1,120 rpm a set of basic jaws inside/outside without Lynette (but can be provided for customization) incl. documentation
Vertical lathe MORANDO 3000 for sale Technical data: X axis: 1500 mm Axial travel: 1200 mm Turning diameter: 3100 mm Maximum turning height: 1840 mm Platform diameter: 3000 mm Maximum table load: 47000 kg Spindle power: 52 KW Number of spindle revolutions/minute: 100 rpm CNC: Siemens 840D
SWH GmbH
