Manufacturer:
(Category: 102)
CAPACITIES AND CHARACTERISTICS CNC Fagor 8055 Retrofitted in 2018 TABLE – CROSS SLIDE • D – Table diameter: 2050 mm • A – Maximum turning diameter: 2300 mm • DB – Normal table height from the floor: 731 mm • H – Maximum machinable height (tool overhang 15 mm): 2000 mm • T – Vertical stroke of the cross slide: 1700 mm • Continuous range of table speeds: 1.6 to 200 rpm • Table motor power: 37 kW • Maximum allowable load on table: 20 tons • Cross slide travel speed: 400 mm/min TOOL CARRIAGE • Section of the tool carriage slide: 224 x 224 mm • C – Travel of the tool carriage slide: 1600 mm • CD – Travel to the right of the table axis: 1305 mm • CG – Travel to the left of the table axis: 400 mm • Continuous feed range: 0.05 to 24 mm/rev • Tool positioning speed: 1 to 3600 mm/min Verniers: • 1 divisi ...
A Pinacho CNC precision parallel lathe is available. Center height: 180mm, center width: 750mm-1000mm, turning diameter over guide bed/longitudinal slide/cross slide: 360mm/335mm/198mm, bed width: 250mm, bore: 42mm, speed: 4000rpm, feed X/Z: 10m/min, rapid traverse X/Z: 10m/min. Tailstock shank diameter: 58mm, tailstock shank length: 200mm, Morse taper: MK3, min. travel of moving/fixed steady rest: 10mm, max. travel of moving/fixed steady rest: 70mm/114mm, control: Fanuc 0i. Documentation available. On-site inspection is possible
Turning diameter over bed/face slide: 360mm/160mm, center distance: 800mm, travel X/Z: 205mm/810mm, speed: 3150rpm, spindle bore: 60mm, tool positions: 8, rapid traverse X/Z: 10m/min. Machine dimensions X/Y/Z: approx. 3300mm/1800mm/1800mm, weight: approx. 3300kg, control: Traub System TX-8. An on-site inspection is possible.
turning diameter over bed: 250 mmturning diameter over slide rest: 145 mmturning length: 550 mmcenter height over bed: 125 mmcentre distance: 550 mmbed width: 135 mmspindle bore: 26 mmturning speed range - stepless: 50 - 2.000 U/minpower requirement: 750 W3-jaw-chuck diameter: 125 mmtaper in tailstock-quill: MK 2 dia. of quill: 30 mmquill stroke: 70 mmvoltage: 230 Vweight of the machine ca.: 120 kgdimensions of the machine ca.: 1,25 x 0,60 x 0,50 mThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
workpice diameter max.: 90 mmforward bearing diameter: 140 mmTurning speeds mainspindle: 4.200 U/minPower: 35,5 KWControl: INDEX C 200-4 travel -x axis: 1.500 mmtravel -z axis: 340 mmtravel -y axis: 180 mmb-axis: 360 °CNC turning and milling center vertical | INDEX - V300 equipped with a turret for driven tools as well as y- + B- axis.Further information:- direct measuring system on X + ZThe machine is in good condition.For additional equipment information please refer to the original order confirmation which is included in the offer of this machine.- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -#Tags: V-300 | V 300The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
: 0390 mm: 240 mm: 1250 mm: 190 mm: 54 mm: 5,5 kWThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
used
Turning diameter 400 mm Turning lenght 800 mm Spindle speed 4000 rpm With C axis Controller Siemens 840D
UGB-150 widht: 1435mm rangę diameter : ø600 do ø1500mm maks. distance: 1500mm
Key data: 430 mm, 1000 mm, 430 mm
Turning length: 1,000 mm Turning diameter over bed: 430 mm Turning diameter over slide: 255 mm Spindle speeds: 19 - 2,000 rpm Spindle bore: 56 mm Equipped with: - Various Multifix tool containers - Coolant device Country of origin: Germany Motor power: 7.5 kW Machine LxWxH: 360 x 103 x 130 cm Machine weight: 1800 kg
Key data: 870 mm, 3000 mm
Turning length: 3000 mm Turning diameter: 870 mm above bed 560 mm over cross slide Weight between tips: 3,600 kg without bezel 4,400 kg with 1 bezel 5,600 kg with 2 bezels Spindle speed: 0 - 900 rpm Spindle bore: 162 mm Control: Fagor Equipped with: - Extra jaw chuck on the rear side of the main spindle - 1 fixed bezel Ø420 mm - 1 rotating bezel - 4-jaw chuck Ø800 mm - 3-jaw chuck Ø 400 mm - 10 tool containers - Coolant and chip container at the rear - Machine documents Country of origin: Spain Motor power: 30 kW Machine weight: 9,000 kg Machine LxWxH: 5.1 x 2.4 x 2.0 mtr.
Circumferential diameter over bed ... 500mm Turning length ... 2000mm Max. workpiece weight ... 300kg Circumferential diameter via support ... 270mm Spindle bore ... 52mm Spindle speed ... 22-2000 rpm Main engine power ... 5.5kW L x W x H ... 3640x1100x1580mm Machine weight ... 1940kg The machine is in good condition, possible to test under power.
12 position upper turret (6 are driven) -10 positionlower turret (5 are driven) - sub spindle - 2 x C axis - equipped with Lns Sprint S2 bar loader with front magazine, fixed and driven tool holders, manuals - Fanuc 18T Control
Circulation/rotation Ø over bed: 475 mmRotation/rotation Ø via cross slide: 260 mmSledge path plan: 260 mmcentre distance: 1000 / 1500 / 2000 mmpower capacity: 22 kWGear stages. m= manual / e= electric.: 2 e Spindle head DIN 55026 / DIN 55027: A6 / 6 Spindle Ø in front bearing: 115 mmspindle bore: 78 / 70 mmturning speed range (V-constant): 1 - 3.000 U/minfeed range flat: 1µ - 1.000 mm/Ufeed range lengthwise and thread: 1µ - 2.000 mm/URapid traverse plan/longitudinal: 5 / 10 m/mindiameter of quill: 70 mmquill travel: 120 mmquill inner cone: 5 MKThis machine is used for the production of individual parts and small batches from simple to the most complex contours.It is characterised by:--> Ease of operation Precision Working range
: 0400 mm: 1250 mm: : 200 mm: 80 mm: 315 mm: 2700 U/min : D1-8 DIN 55029 : 73 mm: 140 mmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
number of spindles: 8 bar capacity: 36 mmcontrol: FANUC 30i-B Subspindle speed: 7.500 U/minBar Automatic Lathe - Multi Spindle | DMG GILDEMEISTER - MULTISPRINT 36 equipped with bar feeder and a coolant system.The machine only has 15.666h spindle hours.The machine is in a well-maintained condition and can be inspected under power.For additional equipment information please refer to the original order confirmation which is included in the offer of this machine.The machine works with a EGS loading system ->This can be purchased separatelyAn extensive tool package is included.- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -#Tags: MULTISPRINT36 | MULTISPRINT-36The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
