Manufacturer:
(Category: 106)
pressure: 4,5 kNstroke: 40 mmthroat: 95 mmWorking height from to: 95 - 240 mmtable surface area: 160 x 110 mmspindle diameter: 25 mmweight of the machine ca.: 24 Kgdimensions: 160 x 230 mmDirect-acting pneumatic pressesbring the full pressure performance over the entire stroke length. You will above allused when long-stroke parts are machined with constant forceNeed to become.Convincing technology• Long and precise spindle guide for maximum dimensional accuracy• Hardened and ground piston rod for practically unlimited service life• Double-acting cylinders with end position cushioning on both sides• Double guide rings in the piston, constant and quiet running• Oil resistant sealing elementsSpecial features of the PND series• Spindle secured against twisting• Spindle return on the PND 85/S only via a cylinder chamber additional air savings• Easy, quick and prec ...
Dimensional range: M6-M14, length range: 110mm, number of strokes min./max.: 110strokes/125strokes/min, max. wire diameter: 15mm, slide stroke: 160mm, pressing force: 100t, oil capacity: 70l, oil type: CLP 68, clutch manufacturer: Ortlinghs, air consumption at 30 operations/min: 800l/min, weight: approx. 23000kg.
Punching force: 110t, max. punching capacity: 40mm/20mm, throat depth: 750mm, stroke rate: 28/min, max. stroke: 80mm, working height: 1066mm, machine dimensions X/Y/Z: approx. 2300mm/1300mm/2300mm, weight: approx. 4000kg. An on-site inspection is possible.
Max. Press force: 1000kN, max. retraction force: 110kN, max. stroke: 360mm, max. working pressure: 251bar, installation height: 560mm, control panel: Siemens SIMATIC OP27, weight: 7.5t, on-site inspection is possible.
Four Neff single-column presses are available. 1) Neff T 6.3, year of manufacture: 1989, output: 3kW. 2) Neff single-column press, operating hours: 9097h. 3) Neff EP 10 single-column press, year of manufacture: approx. 1950. 4) Neff single-column press. On-site inspection is possible.
ram capacity: 2000 treturn capacity: 150 ttable-size: 1015 x 1050 mmram head dimension: 975 x 1050 mmdist. between pillars (left to right): 975 mmdayligth: 1000 mmdistance table/ram: 600 - 1000 mmram stroke: 400 mmtable height over floor: 800 mmheight over floor: 3650 mmTable ejector: 63 KNRam ejector: 650 KNTable ejector stroke: 100 mmRam ejector stroke: 100 mmLenght of ram slide guiding: 1400 mm: Idle speed downward: 235 mm/sworking feed: max. 20 mm/secWorking speed at 10000 KN: 14 mm/sWorking speed at 20000 KN: 5 mm/sIdle speed upward: 250 mm/sovertravel time: 220 mssafety distance: 352 mmtotal power requirement: 194 kWweight of the machine ca.: 105 tdimensions of the machine ca.: ca. 5,00 x 6,50 x 8,00 mTechnical data without engagement: sizing press with oil-hydraulic drive, hydr. and electrical control depending on UVV, light barrier (Comp. Sick), ejector in table and pusher!The ...
A Bruderer differential stroke press (knuckle-joint press) is available. Press force: 3200kN, installation height min./max.: 420mm/520mm, clamping table dimensions X/Y/Z: 1400mm/1000mm/150mm, table height: 1030mm, ram dimensions X/Y: 1000mm/800mm, belt passage width and height: 400mm/450mm, machine dimensions X/Y/Z: approx. 2350mm/1850mm/4550mm. Documentation available. On-site inspection is possible.
Pressing force: 2000kN, max. installation height: 550mm, total power requirement: 72kW, operating pressure: 210bar. Including feed unit. On-site inspection is possible.
Pressing force: 440kN, working width: 1600mm, cylinder stroke: 150mm, travel X/R: 400mm/200mm, adjustment speed R-axis: 200mm/s, installation height: 400mm, throat depth: 200mm, machine stand distance: 1530mm, motor power: 7.5kW, weight: approx. 2100kg. Including various accessories and tools. Documentation available. On-site inspection is possible.
Press force: 160t, stroke adjustment: 20mm-140mm, stroke rate: 10-60 strokes/min, table dimensions X/Y: 1050mm/820mm, opening in table: 300mm/300mm, ram adjustment: 100mm. On-site inspection is possible.
A Mammut trimming machine in mint condition for the further processing of drawn and pressed parts including welding device is available. Operating hours: 444h. Including welding device CEA BSW 50, documentation available. On-site inspection is possible.
Pressing force: 63t, operating pressure: 160bar, pressing speed downwards/upwards: 200mm/400mm/s, ram stroke: 500mm, throat depth: 360mm, max. ram table distance: 800mm, weight: approx. 4200kg. On-site inspection is possible.
A roller press (briquetting press) Köppern Maco is available. Production capacity: 10 MT/h, roller diameter: 720mm, roller width: 315mm, briquetting shapes: bolted segments, motor type: Siemens electric motor, motor power: 190kW, gearbox type: spur gear, machine dimensions X/Y: approx. 5000mm/5000mm, weight: approx. 15000kg, control: Siemens S7-300 Simatic. Including two new segment sets and one installed segment set. Documentation available. On-site inspection is possible.
A Sahinler workshop press is available. Press pressure: 150t, max. pressure: 244bar, working width: 1520mm, piston stroke: 300mm, ram dimensions X/Y: 200mm/1520mm, through hole: 100mm, table dimensions X/Y: 600mm/1520mm, max. installation height: 610mm. Forward speed: 9mm/s, retraction speed: 10mm/s, working speed: 5mm/s, drive power: 11kW. Machine dimensions X/Y/Z: approx. 2500mm/1000mm/2400mm, weight: approx. 3000kg. Documentation available. On-site inspection is possible.
Compressive force: 1000kN/100t, ram stroke: 200mm, max. operating pressure: 290bar, control: DNC70, safety distance: 166mm, overtravel time: 104ms, overtravel distance: 7mm.
Pressing force: 2000kN, max. stroke: 400mm, throat depth: 300mm, ram table distance: 965mm, ram speed forward/reverse: 100mm/s, working speed: 10mm/s, table width: 1700mm, working length: 2600mm, working height: 1080mm, column distance: 2300mm. Machine dimensions X/Y/Z: approx. 3750mm/2600mm/3600mm, weight: approx. 17500kg. On-site inspection is possible.
Pressing force: 2000kN, working width: 3100mm, column passage: 3240mm, max. stroke: 400mm, throat depth: 250mm, max. installation height: 965mm, NC axes: 11, hydraulic volume: 550l, machine dimensions X/Y: approx. 4400mm/3400mm, weight: approx. 16600kg, control: Cyb-Tech Infinitron. Documentation available. On-site inspection is possible.
An old Künstner & Hampel eccentric press is available. Pressure capacity: 25 tons, power requirement: 2.5 HP. On-site inspection is possible.
Installation height: 408mm, max. working pressure: 315bar, max. pressing force upper piston/lower piston: 630kN/100kN, upper piston retraction force: 71kN, max. stroke upper piston/lower piston: 160mm/80mm, overtravel: 26mm, overtravel time: 106ms, safety distance: 169mm, hydraulic oil capacity: 250l, weight: approx. 3700kg, operating hours: 9283h. Documentation available. On-site inspection is possible.
A high-performance cold press is available for pre-pressing diamond segments in tools. Main cylinder: 2, cylinder diameter top/bottom: 100mm/100mm, cylinder stroke top/bottom: 180mm/150mm, max. operating pressure: 300bar, press force: 235kN. Die clamping cylinder: 2, piston diameter: 63mm, cylinder stroke: 15mm, max. clamping force: 62kN, max. operating pressure: 200bar, piston area: 31.2cm². Weighing stations: 2, weight range: 1g-50g, accuracy: +/-0.05g, powder hopper volume: 12l. Machine dimensions X/Y/Z: approx. 1800mm/1000mm/1900mm, weight: approx. 2000kg. Documentation available. On-site inspection is possible.
Key data: 50 t, 1600 mm, 200 mm
CNC Press Brake COLLY 502/A Numerical Command: CYBELEC type DNC 32 P-CM Capacity: Maxi length 2000 mm x 50 T Throat depth: 200 mm Distance between uprights: 1600 mm Back Gear Gauge 1 axe Defective cylinder Right cylinder joint to change Machine functional (only right cylinder joint to change) Voltage: 380 V Length: 2500 mm Depth: 2100 mm Total height: 2400 mm Weight: approx 4 T
