subcategories
(3rd category level)
Manufacturer:
(Category: 706)
2 Head Automated Cask Washer - Second Hand 2 heads cleaning, stainless steel cask washer, with rotating spray balls. Heated detergent tank Air Actuated Valves Single Phase 240 Volts Manufactured by ABUK - 10/07/2004 Serial Number: AB06 For more information and more available stock please visit us at - advancedbrewing.co.uk
Brewing Kettle /Hot water tank 75HL Vertical cylindrical stainless steel External cladding and insulation finished in riveted stainless steel Mounted on 4 stainless steel legs with adjustable feet Working Capacity 75HL Vessel is fitted with a Lanemark gas burner Vessel is fitted with a wedge wire floor for whole flower hop retention. Previous owner devised a successful method for using pelletized hops utilising an upstand on the central outlet below the wedge wire floor. For more information and more available stock please visit us at - advancedbrewing.co.uk
Grist Hopper - Second Hand Stainless Steel Manufacture: APS Length Approx 2000mm Width Approx 2000mm 4" Flange Outlet Second Hand For more information and more available stock please visit us at - advancedbrewing.co.uk
75HL Vessel - Atmospheric Fermenting vessels Vertical Cylindrical with conical base Approx dimensions: Overall height 4850mm Overall diameter 2200mm Legs 1830mm Top Dish 450mm Working capacity 75HL Max Brim full capacity 100HL estimated Fittings inlet/outlet 2” RJT Vessels fitted with internal rotating sprayballs ,sample taps, ,racking point with racking arm and a central top manway entrance There are cooling jackets on the Cone and the side wall (single zone) Vessels are insulated and clad in riveted stainless steel The vessels have previously operated at up to 3 Bar. However there are no specification plates on the vessels and the design drawings are not available Second Hand For more information and more available stock please visit us at - advancedbrewing.co.uk
Porter Lancastrian 1500L/10BBL Vessel - Second Hand Vertical stainless steel tank Manufacture: Porter Lancastrian Dished Top & Bottom Diameter Approx 1000mm Overall height Approx 2900mm Single Skin Stainless Steel Inlet 1" RJT Side Manway Sight Level Tube Front Sight Port 3 x Legs Second Hand For more information and more available stock please visit us at - advancedbrewing.co.uk
1000l Vessel - Dish Bottom Vertical stainless steel tank Diameter Approx 1050mm Overall height Approx 1650mm Side entry manway door Single skin stainless steel 1.5" RJT Top and Bottom Fittings Sight Glass DIN 80 Top fitting for gas vent 3 x Adjustable Feet Second Hand For more information and more available stock please visit us at - advancedbrewing.co.uk
1000L Vessel - Dish Bottom Vertical stainless steel tank Manufacturer: BBG Diameter Approx 1200mm Overall height Approx 1900mm Side entry man way door with DIN 15 Male Sample Port and Sample Tap Cooling Jackets Insulated with stainless steel cladding CIP Arm with Spray Ball Bottom Central Outlet DIN 50 Male Racking Outlet DIN 25 Male Temp Probe Pocket 2 x Sight Glasses 3 x Adjustable Feet Second Hand For more information and more available stock please visit us at - advancedbrewing.co.uk
1000l Cylindroconical Vessel Vertical stainless steel tank Floor Length Cladding Manufacturer: BBG Diameter Approx 1200mm Overall height Approx 2300mm Side entry man way door with DIN 15 Male Sample Port Cooling Jackets Insulated with stainless steel cladding CIP Arm with Spray Ball Temp Probe Pocket Bottom Central Outlet DIN 50 Male Racking Outlet DIN 25 Male 2 x Sight Glasses 3 x Adjustable Feet Second Hand For more information and more available stock please visit us at - advancedbrewing.co.uk
Cylindrical, Vertical stainless steel tank 25BBL Working capacity Supplied By East field Process Diameter Approx 2400mm Overall height Approx 2850mm Top entry man way door External cooling Jackets on tank shell Insulated with stainless steel cladding over Second Hand For more information and more available stock please visit us at - advancedbrewing.co.uk
GEA Homogeniser Last used in 2020 Full asset list and spares available upon request
Single head semi automated cask filling machine, that incorporates isinglass finings dosing. Manufacture : Microdat Model: CF55 Year of Manufacture: 2013 Single phase For more information and more available stock please visit us at - advancedbrewing.co.uk
Moravek CW Carbonator & Bottle Filler. Twin-head machine. Various Prices as we currently have a few in stock. - Please Enquire Product is carbonated immediately product prior to filling. Range of bottle sizes from 0.2 litres to 2 litres capacity. Filling of glass bottles and P.E.T. bottles. Filling still or carbonated product. Suitable for a wide range of beverages including beer, wine, soft drinks, mineral water, cider and champagne. Simple to operate and flexible. Capable of carbonating at ambient temperature. Available with additional chilling, if required. Compact. Occupies minimal floor space. Integral product pump. Simple to change bottles sizes. All stainless steel construction. This is a second hand machine offered in good condition. For more information and more available stock please visit us at - advancedbrewing.co.uk
Krones Spirit Filling Line Max Speed 18,000 BPH Suitable for 70cl, 75cl and 1 litre bottles Includes; Accummulator - Hartness Dynac - Dynac 6400 - 2004 Cap Feed Elevator - Gassner - Compact Feeder - 2005 Cap Feeder Elevator - Zalkin - Promach 400l - 2020 Cap Feed Elevator - Zalkin - FCT 1911 - 1998 Cartoner - Langenpac - HCC - 2004 Case Erector 1 - Krones - Variocart C-40 - 2004 Case Erector 2 - Krones - Variocart C-40 - 2004 Case Printer 1 - Marsh - Encore - 2007 Case Printer 2 - Marsh - Encore - 2007 Case Sealer - Krones - Variocol H-120 - 2004 Depallitiser - Krones - ABSCH.PRESS.URI1 - 2004 Deshrouder - MSK - MSK 800 - 2004 Divider - SFT Syncro Laner - VWS - 2004 Fill level inspection - Mapex - FLO - 2004 Capper 1 - Zalkin - T9/360 - 2004 Capper 2 - Zalkin - T9/360 - 2004 Capper 3 - Zalkin - T9/360 - 2004 Filler Bloc ...
Velo 40cm x 40cm Filter Frame with Pump Second Hand Manufacturer: Velo acciai Model Type: SF44NDF Serial No: 13789 For more information and more available stock please visit us at - advancedbrewing.co.uk
Vertical Cylindrical Conical Bottomed Fermenter. Stainless Steel. - Second Hand 2500L / 25HL - Brim Full Capacity Top entry manway doors. Cooling Jackets, insulation and cladding, with two cooling zones on cone and tank wall. Fully Welded Cladding in stainless, insulated 50mm. Sample tap & temp probe pocket. Bottom outlet with 1.5" RJT Male Valve. Manufactured Approximately 2015. Total Height: 3330mm - 3100mm - depending on which tank. OD: 1750mm - 1650mm - depending on which tank. For more information and more available stock please visit us at - advancedbrewing.co.uk
Vertical Cylindrical Conical Bottomed Fermenter. Stainless Steel. - Second Hand 2500L / 25HL - Brim Full Capacity Top entry manway doors. Cooling Jackets, insulation and cladding, with two cooling zones on cone and tank wall. Fully Welded Cladding in stainless, insulated 50mm. Sample tap & temp probe pocket. Bottom outlet with 1.5" RJT Male Valve. Manufactured Approximately 2015. Total Height: 3330mm - 3100mm - depending on which tank. OD: 1750mm - 1650mm - depending on which tank. For more information and more available stock please visit us at - advancedbrewing.co.uk
Overview The swing top closing machine was built in 2004 by the German manufacturer Rico. The machine is still in operation and can be inspected at any time. Technical data Output: 12,000 bottles/h Formats: 0.33 l (Steinie bottle) 14 capping stations Running direction: clockwise Touch panel for operation Control system: Siemens S7
- With chassis - Belt length, between axles: 6'500mm - Belt width : 300mm - Motor: 400V, 50Hz - With large inlet hopper attachment - Dumping height : approx. 1200mm - Hopper width: 1000mm - With rack and pinion winch - In good condition
8-fold cartridge filter housing with new filter elements on request for an extra charge
A 3-compartment filter housing is sold On request and for an extra charge with new filter elements
A Kematec MBK 1 AR clocked rotary bottle capper is available. On-site viewing is possible.
GRACO pneumatic pump used in a pharmaceutical factory, Max Air WPR: 1.2 MPa / 12 bar / 180 PSI, Max fluid WPR: 6.2 MPa / 62 bar / 900 PSI , Max Flow: 9.5 L/MIN / 2.5 GPM / 5:1 RATIO , LPM: 9.5, MOC: 2.5, MPa: 1.2, bar: 12, PSI: 180, Max air WPR: 1.2 MPa / 12 bar / 180 PSI, MaxFlow: 9.5 L/MIN / 2.5 GPM / 5:1 RATIO
GRACO pneumatic pump, ATEX, Max flow: 9.5 L/min / 2.5 GPM / 5:1 RATIO , Max Air WPR: 1.2 MPa / 12 bar / 180 PSI , Maxflow: 9.5 L/min / 2.5 GPM / 5:1 RATIO, Max fluid WPR: 6.2 MPa / 62 bar / 900 PSI , Max air WPR: 1.2 MPa / 12 bar / 180 PSI
(Exhibition model) - Material : DIN 1.4301, upper bottom and dome made of DIN 1.4404 - Surface, inside: III d, weld seams pickled and ground - Exterior surface : marbled - Capacity : approx. 2400L Dimensions : - Depth : approx. 1310 mm - Width : approx. 1080 mm - Cooling jacket height: approx. 1750 mm - Height of the shelves : approx. 450 mm - Total height : approx. 2570 mm Equipment : - 4 adjustable feet - Rectangular manhole 420x320 mm - Residual drain with disc valve NW40, Fredrich no 2 NW40 - Clarification drain with ball valve NW40, Fredrich no 2 NW40 - Stand display - Sampling - Thermometer, digital - Double jacket with piping pulled upwards - Labeling board - Ladder bracket - Dom NW 300 Vent Nozzle NW 50 - Crane straps
with 200 mm adhesive height Running direction: left - right Frequency-controlled
Blowing machine KRONES Contiform S 8 year of manufacturing: 2003 capacity: 14.000 bph neck size: PCO 28 - 1881 Bottle size: 1,5 ltr. PET bottle incl. cooling unit incl. preform feeding system incl. preform container incl. preform tilting device air conveyor system is available immediately available in Germany The machine is in a good condition.
Running direction: left - right with safety cladding Capacity: 1,500 - 7,000 bph including glue pump Top condition
PET Aseptic filling line Sidel There are 2 capacities: 18.000 ltr./h and 27.000 ltr. / h - depending on the bottle sizes Capacity: 36.000 bph by 0,5 ltr. and 0,4 ltr. 18.000 bph by 1,5 ltr. Year of manufacturing: 2006 - 2025 Aseptic line produces aseptic products and has been operating since 2006. All maintenance activities have been done twice / year according to OEM specification and with original OEM parts by OEM service technicians. The line includes processing area (mixer, pasteurizer and aseptic tank) APA platform (solution for sterilizing the PET bottles and caps), filler, CIP modules for processing and filler, 4 cameras full bottles inspector (360 degrees), accumulation table, labeling machines (roll on and sleever) packer, palletizer and stretch wrapper. OEM for the sensitive part of the line is Sidel and for processing – Tetra Pak. Over the years, all main elect ...
CIP tank. Volume 2x 5.000 liter (1x compartment of 10.000 liter dividend in 2x compartments). Pressure in the tank: ATM. Aearator on top of the tank. Manholes on the side (oval 450 x 300 mm) and on the top (400 mm diameter) of the tank (1x for each compartment). CIP bowls for cleaning inside the tank. 3 Stainless steel legs. Outlet in the bottom, 110 mm height. Cylindrical height: 3.000 mm. Total dimensions: Ø 2.300 x 4.100 mm. The tank has a lot of lime on the inside., Additional features:, Tank already dismantled out of the factory and located in an outside warehouse in France., Has been a set of 3x tanks, stocknumber: #911 / #912 / #913., Type of Machine: CIP Tank, Volume: 2x 5.000 liter, Double jacketed: No, Insulation: No, Material: SS 304, Type of agitator: No agitator, CIP Spray bowls: Yes, Manhole: Yes 2x pieces, one in each compartment, Number of feet: 3, Internal height: 3.000 ...
