We use cookies to optimize our website for you and to be able to continuously improve it. By continuing to browse the site you are agreeing to our use of cookies.
Disagree
Type; AUMA 15SN X 1600 Manufacturer: Berstorff, Germany Year of manufacture: 1998 Technical Specification: Working width: 1600 mm Steel belt width: 1750 mm Steel belt thickness: 1,8 mm Steel belt length: 15600 mm Rolls width: 1950 mm Center distance between frames: 2330 mm Heating roll diameter: 1500 mm Stretch rolls (I, II, III) diameter - 1000 mm Vulcanizing time: 1?30 min Working speed: 7?.210 m/h Max steam pressure in heating roll: 13 bar Max steam pressure in lower stretch roll: 8 bar Surface temperature of: Heating roll: ca. 195oC Lower stretch roll: ca. 175oC Pressure in heating zone between steel belt and rubber: 60 N/cm2 Main motor speed: 1 ...
QTY 1 x Berstorff Auma, Original year of manufacture 1972, Main Drum 1700mm wide x 1000mm dia, Aux drums 1700mm x 600mm dia, Steam heated, currently with 1660mm wide rubber coated woven steel belt, max pressure 192 Bar (approx 3000psi), 2 speed gearbox, Modern 5.5kW DC variable speed motor. Including let off and wind up units. Complete and in good working condition.
QTY 1 x used Berstorff AUMA Serial no. AO 3178/75, year 1975, Main drum width +/- 2500mm Main drum dia +/- 3000mm Aux drum dia. 1400mm Thermal oil heating With Sandvik 2250mm 1650SM grade stainless steel belt 1.8mm thick. Hydraulic pressure 350kp/cm With 40HP motor and 3 stage reduction gearbox. The main drum and steel belt are in good/serviceable condition (the drum and belt were replaced in 1990's). Note ALSO Available: 1 x new/unused spare Sandvik 1650SM grade stainless steel belt, 2250mm wide (in original crate).
1 x Berstorff GmbH 250mm strainer extruder, Year of manufacture: 1988, L/D ratio 7:1, power roller feed (300mm wide), with 120kW, 1800rpm DC variable speed motor mounted on top of gearbox (belt drive), with tube head and knife at top for sheet extrusion. Complete with control panel etc and in very good condition.
Pin-Convert-Extruder, GE 120 SC, make Berstorff, cold lined ...
Berstorff Strainer Extrusion Line Consisting of: Extruder Supplier Berstorff Type GE 150KSx16D Year of construction 2007 Pins: 12 Pins per level: 8 Condition: good Weight approx. 10000 kg Screen change: hydraulic, bladder accumulator 20lt / 300Bar D = 200mm Gear pump Supplier: Maag Pump Systems Type: extrex® 110-5 RV Volume 716 cm³ / rev Year of construction 2013 Condition: good Heaters Supplier: Regloplas Type P140 Year of construction various Number 5 pcs. Cooling bath Cooling medium Water above, 2 rows below with 4 fans each Year of construction 2006 Condition: good Dimensions 9m Weight approx. 500 kg Especially 8 fans Installation tape Year of constructio ...
Berstorff 8inch (200mm) Cold Feed Pin Extruder Manufactured by: Krauss Maffei Berstorff Extruder Type: Vac GE 200 SC, Pin Type No of Pins: 2 X10 + 1X12 (Hydraulic adjustment) Screw Diameter: 8"/200 mm L/D ratio 18:1 Drive: 300 Kw, 1500 RPM Screw speed: 33pm Complete with Control Panel Roller Die Suitable for rubber compounds Year 2009
Berstorff 6inch (150mm) Strainer Extruder Manufactured by: Krauss Maffei Berstorff Model: GE 150 K Screw Diameter: 6"/150 mm L/D Ratio: 6 Speed: Variable, up to 45 rpm Motor: 90 KW, 1500 RPM Transmission: Direct Drive, 3 steps reduction Gear Reduction Ratio: 33:1 Year 2009 ...
available Berstotff Rollerhead - Extruder Cold Feed Extruder - 200mm x 218D 2 roll calendars 400mm x 1200mm see attached description! ...
Extruding height 1010 mm, Mailefer screw, ...