clamping force: 350 kNinjection volume: 59 cm³screw diameter: 25 mmplaten size: 400 x 400 mmCondition: used,Specification: injection moulding machine for rubber - used International size: 350-90 clamping unit:- clamping force: 350 kN- clamping platen size: 400 x 400 mm- Clear distance between tie bars: 270 x 270 mm- Mould installation height min.: 225 mm- Distance between clamping platens: max. 550 mm- Opening stroke max.: 325 mm- Ejector stroke: 125 mmInjection unit:- Screw diameter: 25 mm x 20D- Injection volume max.: 49 cm³- Injection part weight: 59 g/hp- Max. injection pressure: 1,860 bar- Screw circumferential speed: 37 m/min- Cylinder heating: 4x 900 W- Nozzle heating: ...
clamping force: 1.300 kNinjection volume: 230 cm³screw diameter: 45 mmplaten size: 685 x 685 mmCondition: used,Specification: injection moulding machine for TPE - usedincluding Koch dosing unitclamping unit:- clamping force: 1.300 kN- heating platen size: 685 x 685 mm- Clear distance between tie bars: 470 x 470 mm- Mould installation height min.: 250 mm- Distance between platens max.: 900 mm- Opening stroke max.: 650 mm- Ejector stroke: 225 mmInjection unit:- Screw diameter: 45 mm x 18D- Injection volume max.: 230 cm³- Injection part weight: 210 g/hp- Max. injection pressure: 1,670 bar- Screw circumferential speed: 75 m/min- Cylinder heating: 4x 2,200 W- Nozzle heating: 600 W- Connection value: 3x 400 V, 50 Hz- Electrica ...
clamping force: 350 kNinjection volume: 58,5 cm³screw diameter: 28 mmplaten size: 260 x 254 mmCondition: used,Specification: injection moulding machine for TPE - usedclamping unit:- clamping unit: vertical- clamping force: 350 kN- opening stroke max.: 300 mm- platen distance max.: 500 mm- Mould installation height min.: 200 mm- Clear width between tie bars: 260 x 254 mm- Ejector stroke max.: 80 mm- Clamping unit: VV- Lift of protective bonnet: 500 mmInjection unit:- Screw diameter: 28 mm- Screw L/D ratio: 18.6- Screw stroke max.: 95 mm- Injection volume max.: 58.5 cm³- Injection pressure: 1577 bar- Plasticising flow: 8.6 g/s- Injection flow: 85.5 g/s- Connected load: 3x 400 V, 50 Hz- Max. heating power: 5.8 kW- Drive power: 7,4 kW- Total power: ...
clamping force: 11000 kNinjection volume: 12500 cm³screw diameter: -- mmplaten size: -- mmCondition: used,Specification: injection moulding machine for rubber - used, in very good condition machine was serviced annually by manufacturerclamping unit:- Euromap (size): 11000-25600- clamping force: 11.000 kN- size of heating platens L/W/H: -- x -- x mmInjection unit:- Injection volume max.: 12,500 cm³- Injection pressure: 2050 bar- Dosing force: 118 kN- Control: Siemens S7- Connected load: 3x 400 V, 50 Hz, N- Total current: 276 A- Back-up fuse: 300 A- Pump drive: 277 bar- Driving power: 45 kW- Weight approx.: 43.8 tOperating hours approx.: 33,130 hoursThe data for this ad was created with ModulMWS - t ...
clamping force: 13500 kNinjection volume: 22900 cm³screw diameter: -- mmplaten size: -- mmCondition: used,Specification: injection moulding machine for rubber - used, in very good condition machine was serviced annually by manufacturerclamping unit:- Euromap (size): 13500-46900- clamping force: 13.500 kN- size of heating platens L/W/H: -- x -- x mmInjection unit:- Injection volume max.: 22,900 cm³- Injection pressure: 2050 bar- Dosing force: 118 kN- Control: Siemens S7- Connected load: 3x 400 V, 50 Hz, N- Total current: 424 A- Back-up fuse: 425 A- Pump drive: 250 bar- Driving power: 75 kW- Weight approx.: 72,0 tOperating hours approx.: 17,855 hoursThe data for this ad was created with ModulMWS - t ...
DESMA 400 ton rubber injection molding machine -Model : SIGMA 4000
clamping force: 250 kNinjection volume: 49 cm³screw diameter: 25 mmplaten size: 300 x 300 mmCondition: used,specification: C-frame injection moulding machine - usedclamping unit:- clamping force: 250 kN- heating platen size: 300 x 300 mm- clamping/opening stroke: 330 mm- Closing direction: from below- Lateral ejector: yes- Ejector stroke/force: 115 mm / 12 kNInjection unit:- Injection volume max.: 49 cm³- Screw diameter: 25 mm- Screw length: 16- Screw speed max.: 250 rpm- Injection: from above- Voltage: 3x 400 V, 50 Hz, N, PE- Connected load: 55 kW/92 A- Weight approx.: 3,500 kgVarious accessories are also available:- Injection unit (25 screw)- 2 heating plates- Funnel and various small partsThe data for this ad was created with ModulMWS - ...
clamping force: 450 kNinjection volume: 135 cm³screw diameter: 35 mmplaten size: 600 x 400 mmCondition: used,Specification: C-frame injection moulding machine for TPE - usedclamping unit:- clamping force: 450 kN- heating platen size: 600 x 400 mm- sliding table: yes- Clamping direction: from below- Ejector / lifter: Up + LoInjection unit:- Injection volume max.: 135 cm³- Screw diameter: 35 mm- Connected load: 3x 400 V, 50 Hz- Weight approx.: 5,500 kgThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
clamping force: 450 kNinjection volume: 99 cm³screw diameter: 30 mmplaten size: 860 x 320 mmclosing stroke: 406 mmCondition: used,Specification: C-Frame Injection Moulding Machine - second-hand Serial No.: 45083Clamping unit:- Clamping force: 450 kN- Opening travel: 406 mm- Heating plate size: 860 x 320 mm- Mould height min.: 264 mm- Max. plate spacing: 464 mm- Ejector stroke: 20 mm- Ejector force: 20 kNInjection unit:- Screw diameter: 30 mm- Screw length L/D: 16- Dosing stroke: 140 mm- Stroke volume max.: 99 cm³- Max. spray weight: 114 g- Screw speed: 20 - 300 rpm- Injection flow: 106 cm³/s- Injection flow increased: 71 cm³/s- Special injection pressure: 1451 bar- Spec. injection pressure increased: 2205 bar- Nozzle path: ...
clamping force: 450 kNinjection volume: 99 cm³screw diameter: 30 mmplaten size: 860 x 320 mmclosing stroke: 406 mmCondition: used,Specification: C-Frame Injection Moulding Machine - second-hand Serial No.: 45083Clamping unit:- Clamping force: 450 kN- Opening travel: 406 mm- Heating plate size: 860 x 320 mm- Mould height min.: 264 mm- Max. plate spacing: 464 mm- Ejector stroke: 20 mm- Ejector force: 20 kNInjection unit:- Screw diameter: 30 mm- Screw length L/D: 17- Dosing stroke: 140 mm- Stroke volume max.: 99 cm³- Max. spray weight: 114 g- Screw speed: 20 - 300 rpm- Injection flow: 106 cm³/s- Injection flow increased: 71 cm³/s- Special injection pressure: 1450 bar- Spec. injection pressure increased: 2210 bar- Nozzle path: ...
clamping force: 1.550 kNinjection volume: 135 / 49 cm³screw diameter: 35 / 25 mmplaten size: -- mmCondition: used,Specification: injection moulding machine for TPE - used type: K-TEC 155 S/2F clamping unit 1550:- Clamping force: 1,550 kN- Clear column spacing: 500 x 500 mm- Max. platen spacing: 950 mm- Platen spacing min.: 650 mm- Opening stroke min.: 300 mm- Ejector stroke: 180 mmInjection unit 1:- Screw diameter: 35 mm- Injection volume max.: 135 cm³- Injection part weight: 125 g- Injection pressure max.: 1.964 barInjection unit 2:- Screw diameter: 25 mm- Injection volume max.: 49 cm³- Injection pressure max.: 2.254 bar- Connection value: 3x 400 V, 50 Hz- Engine power: 37 kW- Total heating power: 14.8 kW- Electrical connectio ...
clamping force: 2500 kNinjection volume: 2x 190 cm³screw diameter: 45 mmscrew length: 22 D platen size: 510 x 670 mmCondition: usedSpecification: Vertical Injection Moulding Machine for Rubber - second-hand- clamping force: 2500 kN- screw diameter: 45 mm- screw length: 22 D- screw speed: max. 300 rpm- injection volume: 2 x 190 cm3 - Injection pressure: 1900 bar- Number of heating zones: 5- open nozzle with nozzle head - Clear column spacing: 510 x 670- Mains supply voltage: 380 V, 50 Hz- Machine weight approx.: 7.8 t without oil filling- Oil filling approx.: 260 litres, 230 kgTwo identical machines (built 1991, 1993) are available.The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Rotary rubber injection press, good technical condition. Injection volume 1000cm3. Plates size: 500 x 380mm. Clamping force: 2500kN. Plates heating power: 51kW. Max. injection pressure: 180MPa. Good technical condition.
LWB VCE 500/160 C Frame Injection Press Type: VCE-T Year 2006 Clamp force 500kn Injection volume 160 cm3 26kw Suitable for joing and corner moulding
Mapelli 60ton Injection Machine Platen 400 deep x 500 wide Single station Motor invertor driven Omron screen Suitable for joining / corner moulding injection
clamping force: 300 kNinjection volume: 105 cm³screw diameter: -- mmplaten size: 300 x 400 mmCondition: used,Specification: Vertical C-frame Injection Moulding Machine for rubber - second-handsuitable for vulcanising together extruded rubber profilesto sealing frames or for the production of small precisionmoulded parts. The C-frame design ensures very good mould accessibilityaccessibility of the tools from three sides, so that when vulcanisingthe necessary space when vulcanising sealing profiles.to be able to work comfortably even with multiple tools.be able to work comfortably.Injection unit:- Injection volume approx.: 105 cm³- Injection pressure approx.: 1,800 barClamping unit:- Clamping force: 300 kN- Size of heating platen: 300 x 400 mm- Clamping speed: 100 mm/sec- Heating power per platen: 3 kW- Total power with sliding table: 9 kWWith alternating sliding table ...
clamping force: 1.013 kNinjection volume: 400 cm³screw diameter: 25 mmplaten size: 335 x 400 mmCondition: used,Specification: injection moulding machine for rubber - usedclamping unit:- clamping unit: vertical- clamping force: 1.013 kN- size of heating platen: 335 x 400 mm (standard) core turning unit Injection unit:- screw diameter: 25 mm- Barrel diameter: 51 mm- Injection volume max.: 400 cm³- Injection pressure: 1,500 bar- Connection value: 3x 400 V, 50 Hz 42A fuse protection (incl. periphery)- Electrical power: 29,1 kVA- Control: G8 Control- Hydraulics: 250 bar (tank 200 litres)- Further connections: Cooling water inlet/outletDimensions L/W/H approx.: 2,300 x 3,400 x 2,250 mmWeigh ...
