Manufacturer:
(Category: 307)
90 mm cold feed extruder, GE 90 x 18 D with vacuum zone, make Troester, with profile spray head, drive 48 KW Siemens DC, 5 TCU Weinreich TD 6
90 mm cold feed extruder, GE 90 x 16 D with vacuum zone, make Troester, with large hose / profile spray head, drive 48 KW Siemens DC, 5 TCU Weinreich TD 6
Key data: 550 mm, 1500 mm
Mixing mill 550 × 1500 mm, manufactured by Bata in 1937. This historic machine is fully functional and can be used both in production and as an exhibition piece.
Key data: 300 mm, 600 mm
Diameter: 300 mm Length: 600 mm Surface: smooth NIP setting: manual Motor: 30 kW Siemens Dimensions: approx. 1700 x 1560 x 1635 mm Weight: approx. 3000 kg CE marked from 2018 (engine with reverse gear, knee emergency stop)
Powder machine Fabikat PEKU with 1000 mm passage width for powdering top and bottom for Plates, profiles, hoses, etc.
Capacity 75 kg Output capacity max. 800 kg/h Blank weight 0.25 - 3100 g
120 mm cold feed pen convert-extruder, GE 120 SC, make Berstorff, output capacity up to 1,000 kg /h as a power extruder with strip spray head, complete rebuild mechanically and electrically in 2024
Key data: 400 mm, 1000 mm
Buzuluk 14231 CE conversion in 2010 Antifriction bearing Motor: 55 kW Motorized NIP adjustment Baseplate
3 to 5-Roll calender Buzuluk Number of rolls: 4 pcs. Roll diameter: 150 mm Roll length: 400 mm
Press 400x600 make ZDA Type 100660 manualy operated electrical heated plates Clamping force 1540 kN
Press force max.:: 10.000 kNheating plates:: 1200 x 1200 mmelectrically heated:: °Cpiston stroke:: ca. 700 mmno. of stages:: 1 Condition: Second-hand, reconditionedSpecification: Vulcanising press 1200 x 1200 mm, steel plate construction, second-hand, reconditioned- Clamping force approx.: 1,000 t- Clamping action: bottom-up- Heating plates: 2 electric plates- Heating plate power approx.: 2 x 25 kW- Heating plate dimensions: 1,200 x 1,200 mm- Distance between the heating plates, variant 1: approx. 1,100 mm- Distance between the heating plates, variant 2: approx. 1,500 mm- Piston stroke approx.: 700 mm- Hydraulic power unit with new solenoid valves- AC motor for pump approx.: 30 kW to be checked during overhaul- New control cabinet with 7 Siemens touch panel- Sieme ...
Press force: 2800kN, heating platen size X/Y: 500mm/500mm, daylight between the heating platens: 200mm, max. hydraulic pressure: 300bar, heating power: 9.4kW, drive power: 7.5kW, control: Siemens S5 with OP17, weight: approx. 5000kg. Equipped with sliding table, vacuum pump, vacuum chamber and vacuum receiver tank. An on-site inspection is possible.
Press force: 2800kN, heating platen size X/Y: 500mm/500mm, daylight between the heating platens: 200mm, max. hydraulic pressure: 300bar, heating power: 9.4kW, drive power: 7.5kW, control: Siemens S5 with OP17, weight: approx. 4500kg. Equipped with sliding table, vacuum pump, vacuum chamber and vacuum receiver tank. An on-site inspection is possible.
machine measurements: -- mmmachine weight: -- kgpower capacity: -- kWCondition: used, Specification: drum-type blast deburring machine type: MEWO Rotor TS 60- batch volume approx.: 1-100 litres,- working temperature: - 150°C- drum speed: 5 - 30 rpm- Blast wheel speed: 1,000 - 9,500 rpm- Control: Siemens S7 SimaticThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
specimen dia.: - mmlength of specimen: - mmtotal power requirement: - kWweight of the machine ca.: - tdimensions of the machine ca.: - mVolumetric samples - cutter / sample punch The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
roll diameter: 500 mmroll length: 1500 mmrolls drilled: Kernbohrung Nip adjustment: hydraulisch 0total power requirement: 110 kWCondition: used, overhauled Specification: Rolling mill 500 x 1500 mm - second-hand- roller diameter: 500 mm- roll length: 1500 mm- monoblock motor under the rollers- Fixed friction between the rollers- Rollers: with core bore, with central chamber for water cooling- Gap adjustments: NEW hydraulic- Hydraulic unit: NEW- Tilting material guide jaws made of steel with mechanical with mechanical safety interlock- Rollers: mounted on bronze bushes with circulating oil lubrication via pump- New Johnson-Fluiten ball swivel joints for connection to water circuit to water circuit- New safety brake for EMERGENCY STOP- New AC moto ...
roll diameter: 250 mmroll length: 500 mmrolls drilled: Kernbohrung nip adjustment: mechanisch drive power:: kWThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
machine measurements: 3.000 mmmachine weight: -- kgpower capacity: 90 kWThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
roll diameter: 700 mmroll length: 2200 mmrolls drilled: Kernbohrung Nip adjustment: hyraulisch 0total power requirement: 160 kWThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Press force max.:: 3000 kNheating plates:: 600 x 630 mmelectrically heated:: °Cheating power:: kWpiston stroke:: 420 mmno. of stages:: 1 Condition: Used, reconditionedSpecification: Press 600 x 630 mm, second-hand- clamping force: 300 tonnes (3,000 kN)- closing: from bottom to top- Heating platens: 2 electric platens, with new heating rods- Heating platen dimensions approx.: 600 x 630 mm- Distance between the heating platens approx.: 420 mm- New electric valves- AC machine output oil pump: 5.5 kW- New control cabinet with Siemens 7’ touch panel- PLC control system make Siemens S7-1200- New cabling- Frequency inverter made by Schneider- Light barriers in the front area,Overhauled in accordance with CE standard safety regulationsOperating instructions and maintenance instructions in GermanWarranty: 1 yearThe data for this ad was created with ModulMWS - the sof ...
0: 200 °CTorque: - 0Dimensions (HxWxD): 680 x 1320 x 760 mmweight: 177 kgThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
machine measurements: 1500 x 2400 x 1150 mmmachine weight: -- kgpower capacity: 12 kWThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
roll diameter: 550 mmroll length: 1500 mmrolls drilled: peripher Nip adjustment: hydraulisch 0total power requirement: 110 kWCondition: used, overhauled Specification: rolling mill 550 x 1500 mm - used- roll diameter: 550 mm- roll length: 1500 mm- monoblock - motor under the rolls- Fixed friction between the rolls- Rolls: peripherally drilled, for water cooling- Gap adjustments: NEW hydraulic- Hydraulic unit: NEW- tiltable steel material guide jaws- Rollers: mounted on bronze bushes with oil circulation lubrication via pump- new ball bearing slewing rings for connection to water circuit- Safety brake for EMERGENCY STOP- New AC motor 110 kW - 400 V - 50 Hz - New pan for receiving the mixture- Safety bars bi-directional- New electrical control cabinet with PLC system S7-120 ...
screw ø:: 60 mmscrew length:: 11D screw speedl:: -- U/mindrive power:: 18,5 kWCondition: used, reconditionedSpecification: rubber extruder – used- Screw diameter: 60 mm- Screw length approx.: 11D- New screw- Cylinder refurbishment- Feed roller refurbishment- New safety cage- New rotary joint for water- New AC motor: 18.5 kW- New control cabinet with Siemens S7-1200 PLC system- New control panel with Siemens KTP700 Basic touch panel- New Siemens G120 frequency converter for variable speed- Remote maintenance device- New cabling- Pressure sensors on the extruder head- Safety device- CE marking and an operating and maintenance manual in EnglishRefurbished in accordance with CE standard safety regulationsWarranty: 1 yearOption: TCU for temperature control of the water up to 95°C, for placement near the extruderThe data for thi ...
clamping force: 2.700 kNinjection volume: 6.000 cm³screw diameter: -- mmplaten size: 560 x 630 mmCondition: second-hand,Specification: rubber injection moulding machine - second-hand, partially dismantled, but would be restored to its previous condition EUROMAP size 2500 – 7000Clamping unit:- Clamping unit: vertical- Clamping force: 2.700 kN- Platen size: 560 x 630 mm- Max. stroke: 550 mm (see data sheet) Injection unit:- Max. injection volume: 6,000 cm³- Injection pressure: 2150 bar- Power supply: 3x 400 V, 50 Hz, N, PE- Motor power: 28,2 kW- Installed heating capacity: 49,9 kW- Weight: Clamping unit approx.: 6,040 kg Injection unit approx.: 2,700 kg Hydraulic un ...
clamping force: 4.500 kNinjection volume: 3.300 cm³screw diameter: -- mmplaten size: 670 x 780 mmCondition: second-hand,Specification: rubber injection moulding machine - second-hand EUROMAP size 4000 – 7000Clamping unit:- Clamping unit: vertical- Clamping force: 4500 kN- Platen size: 670 x 780 mm- Max. stroke: 600 mm (see data sheet) Injection unit:- Max. injection volume: 3,300 cm³- Injection pressure: 2150 bar- Power supply: 3x 400 V, 50 Hz, N- Motor power: 35,5 kW- Installed heating capacity: 73,9 kW- Weight: Clamping unit approx.: 8,400 kg Injection unit approx.: 2,700 kg Hydraulic unit with oil and control cabinet 2,200 kg Additional equipment (approx.): 3,000 kg ...
clamping force: 4.500 kNinjection volume: 5.600 cm³screw diameter: 610 - 985 mmplaten size: 670 x 780 mmCondition: second-hand,Specification: rubber injection moulding machine - second-hand EUROMAP size 4500 – 12300Clamping unit:- Clamping unit: vertical- Clamping force: 4500 kN- Platen size: 670 x 780 mm- Max. stroke: 610 - 985 mm (see data sheet) Injection unit:- Injection unit type: ADV- Max. injection volume: 5,600 cm³- Injection pressure: 2200 bar- Power supply: 3x 400 V, 50 Hz, N, PE- Pump capacity: 27 kW- Weight: Cutting unit approx.: 10,200 kg Injection unit approx.: 3,500 kg Hydraulic unit with oil: 2,600 kg Accessories approx.: 4,700 kg Total weight approx.: ...
clamping force: 4.500 kNinjection volume: 5.000 cm³screw diameter: -- mmplaten size: 670 x 780 mmCondition: second-hand,Specification: rubber injection moulding machine - second-hand EUROMAP size 4500 – 10000Clamping unit:- Clamping unit: vertical- Clamping force: 4500 kN- Platen size: 670 x 780 mm- Max. stroke: 600 mm (see data sheet) Injection unit:- Max. injection volume: 5,000 cm³- Injection pressure: 2060 bar- Power supply: 3x 400 V, 50 Hz, N, PE- Motor power: 38 kW- Installed heating capacity: 67.5 kW- Weight:Clamping unit approx.: 8,900 kgInjection unit approx.: 3,200 kgHydraulic unit with oiland control cabinet 2,350 kg- For dimensions, see the installation data in the appe ...
clamping force: 300 kNinjection volume: 180 cm³screw diameter: -- mmplaten size: 300 x 300 mmCondition: second-hand,Specification: C-frame injection moulding machine for rubber - second-handClamping unit:- Clamping unit: vertical- Clamping force: 300 kN- Platen size: 300 x 300 mm Injection unit:- Maximum injection volume: 180 cm³- Mains supply: 3x 400 V, 50 Hz- Power rating: 11 kW- Control system: MAPLANThe machine is still in production and can be viewedin operation.The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
roll surface width: 450 mmroll diam. toproll: 203 mmroll diam. bottom roll: 203 mmoutput: 8,8 kwSmall roll gap 0.1 mmMaximum roll gap 47 mmFront/rear roll speed 5-30 rpmFront/rear roll speed 3.2-19.1 m/minRolls individually drivenFriction variable max. 1:6Manual gap adjustmentManual speed controlExternal temperature controlRollers internally cooled (water cooling)Emergency stop handle (manual operation) on both sidesThe tech. Data are manufacturer or operator information and therefore non-binding. We reserve the right to prior sale, Our terms and conditions of sale apply exclusively.About us More than 400 of our own machines in stock Over 15,000 m² of storage space, 70 t crane capacity More than 10,000 items and accessories for your workshop If you are interested in selling machines, production lines, or your business, please contact us. You can find further offers on our website. Tours ...
