Manufacturer:
(Category: 301)
Awaiting refurbishment at our headquarters in Northamptonshire is this BOY 55A injection moulding machine, fitted with the Procan CT Controller. Any machines awaiting refurbishment (or undergoing refurbishment) with us can be reserved with a 10% deposit and we then prioritise the refurbishment and aim to have the machine available for inspection within 8 weeks from order. Refurbished machines from STV Machinery undergo a comprehensive test procedure during which every function of the machine is tested and if necessary repaired. A production run of at least 5000 fault free cycles prior to sign off ensures trouble free operation once delivered. Machines are ultra clean and cosmetically as good as we can get them. We guarantee our refurbs are delivered fault free and leak free. Prices shown are ex-works, but we can quickly provide DAP (Delivered at Place) Incoterm pricing on reques ...
Awaiting refurbishment at our headquarters in Northamptonshire is this BOY 22A injection moulding machine, fitted with the Procan Alpha Controller and 22mm screw. Any machines awaiting refurbishment (or undergoing refurbishment) with us can be reserved with a 10% deposit and we then prioritise the refurbishment and aim to have the machine available for inspection within 8 weeks from order. Refurbished machines from STV Machinery undergo a comprehensive test procedure during which every function of the machine is tested and if necessary repaired. A production run of at least 5000 fault free cycles prior to sign off ensures trouble free operation once delivered. Machines are ultra clean and cosmetically as good as we can get them. We guarantee our refurbs are delivered fault free and leak free. Prices shown are ex-works, but we can quickly provide DAP (Delivered at Place) Incoterm ...
Awaiting refurbishment at our headquarters in Northamptonshire is this BOY 90E injection moulding machine, fitted with the Procan Alpha Controller. Any machines awaiting refurbishment (or undergoing refurbishment) with us can be reserved with a 10% deposit and we then prioritise the refurbishment and aim to have the machine available for inspection within 8 weeks from order. Refurbished machines from STV Machinery undergo a comprehensive test procedure during which every function of the machine is tested and if necessary repaired. A production run of at least 5000 fault free cycles prior to sign off ensures trouble free operation once delivered. Machines are ultra clean and cosmetically as good as we can get them. We guarantee our refurbs are delivered fault free and leak free. Prices shown are ex-works, but we can quickly provide DAP (Delivered at Place) Incoterm pricing on req ...
Key data: 220 kN
Awaiting refurbishment at our headquarters in Northamptonshire is this BOY 22M injection moulding machine. Any machines awaiting refurbishment (or undergoing refurbishment) with us can be reserved with a 10% deposit and we then prioritise the refurbishment and aim to have the machine available for inspection within 8 weeks from order. Refurbished machines from STV Machinery undergo a comprehensive test procedure during which every function of the machine is tested and if necessary repaired. A production run of at least 5000 fault free cycles prior to sign off ensures trouble free operation once delivered. Machines are ultra clean and cosmetically as good as we can get them. We guarantee our refurbs are delivered fault free and leak free. Prices shown are ex-works, but we can quickly provide DAP (Delivered at Place) Incoterm pricing on request. We can take out the hassle and add ...
Key data: 600 kN, 132 g/PS, 35 mm
Arburg 320C-600-250 Injection Moulding Machine (241) Ability to work vertically Number: 241 Availability: in stock Year of production: 2008 Producer: Arburg Condition of Injection Molding Machine: Used Screw diameter [mm]: 35 Injection weight [g]: 132 Injection pressure [bar]: 1820 Clamping force [kN]: 600 Gap spacing [mm]: 320×320 Panel size [mm]: 446 x 446 Min. mould height [mm]: 200 Control Type: Selogica Tongue: German Installed power [kW]: 23.9 Working hours [h]: 74753 Weight [kg]: 2330 Dimensions [mm]: 3500×1500 Feed hopper: NO Robot Socket: Yes Core String: 1x
ENGEL ES 1350/350 HL injection moulding machine was built in 1995 in Austria by ENGEL AUSTRIA GmbH. The machine, which is designed for the economical production of plastic parts, is distinguished by the use of many components with excellent technical parameters. These parts are produced using the reliable injection moulding method, which involves feeding plasticised plastic into a mould and then clamping it with high press force. A precision mould clamping system, operating at a maximum force of 350 tonnes, guarantees high repeatability and quality of the manufactured parts. Once the production process is complete, the robot automatically transfers the finished products from the workspace to a conveyor belt. The ES 1350/350 HL injection moulding machine weighs 5000 kg. Technical specifications of the ENGEL ES 1350/350 HL injection moulding machine - CNC controller: ENGEL - maximum m ...
Clamping force: 220kN, min. mould height: 200mm, max. opening stroke: 200mm, max. platen distance: 400mm, ejector stroke: 80mm, machine dimensions X/Y/Z: approx. 2600mm/800mm/1600mm, weight: approx. 760kg. An on-site inspection is possible.
• Clamping Force: 80 tons (800 kN) • Screw Diameter: 35 mm • Shot Weight (PS): 165 grams • Tie Bar Spacing (H × V): 420 mm × 420 mm • Opening Stroke (Max): 450 mm • Minimum Mould Height: 250 mm • Maximum Daylight (Platen Distance): 700 mm • Control System: Selogica • Power Consumption: 29.9 kW • Machine Dimensions (L × W × H): 5,200 mm × 1,600 mm × 2,200 mm • Machine Weight: 3,800 kg
An almost like-new injection moulding machine Arburg is available. Clamping force: 1600kN, tie bar distance: 520mm, clamping stroke: 364mm, ejector stroke: 150mm, ejector force: 40kN, injection unit: 400, injection pressure: 2500bar. Machine dimensions X/Y/Z: approx. 6000mm/1800mm/2200mm, weight: approx. 6000kg, control: Selogica, operating hours: approx. 67h. Includes enclosure with clean air supply FilterFanUnit and removal robot. Documentation available. An on-site inspection is possible.
Chen Hsong SM4500-TP (2013) Supermaster Servo drive seriesClamping force: 4500 tScrew diameter: 250 mmShot weight: 61166 gDistance between tie bars V: 2100 mmDistance between tie bars H: 2430 mmOpening stroke: 2300-3400 mmShot volume: 67216 cm3Max daylight: 4500 mm
Injection Moulding Machine Krauss Maffei KM 850-12000 MXKrauss Maffei LRX 500 RobotYear of Manufacture: 2011Machine Description:Hydraulic-mechanical two-platen clamping system with 4 pressure pads and 4 locking units on the moving platen.PV-controlled injection unit.MC 5 control system with color monitor, integrated control panel, and USB data storage.Plasticizing Unit:Complete plasticizing system for thermoplastics with a 135 mm diameter screw, shut-off nozzle, and open nozzle.Nozzle radius: 25 mm, nozzle opening: 9 mmTechnical Specifications:Clamping Unit:Clamping force: 8,500 kNMold opening force: 560 kNPlaten size (H x V): 1600 x 1600 mmTie bar spacing (H x V): 1140 x 1140 mmMold opening stroke: 1600 mmMold height (min–max): 500 – 1100 mmDaylight opening: 2100 mmEjector stroke: 300 mmEjector force: 200 / 100 kNInjection Unit:Screw diameter: 135 mmInjection pressure: 1389 barInjec ...
Engel INSERT 330H/90Controll: CC100 Condition: funtional Vertical machine with Horizontal injectionRotary table diameter: 1100mmClamping force: 90 tonOpening max. : 570Opening min. : 270Platen size: 590x340Screw: 40 mmScrew length: 160 mmInjection volume: 201 cm3Injection pressure: 1230 barMotor: 15 kwWeight: 5600 kgHeight 2800 mm
R1304Injection moulding machine ARBURG 270-350-90 Multronica thermoset the previous owner sold the Multronica controller for 2,500€ I wanted to convert the machine to thermoplastic. I also found a Multronica controller. There are the following options ---------------------------------------------------------------------- ----------- without control, without funnel, without thermoset device as Spare parts carrier (engine, pump, valves, cylinders, electrics, etc.) €800,-- ---------------------------------------------------------------------- ------------------- with thermoset module + replacement Multronica for assembly €1000.-- ---------------------------------------------------------------------- --------------------- with additional thermoplastic module €1200.-- ---------------------------------------------------------------------- --------------------- all prices +VA ...
Key data: 850 kN, 40 mm
R1295Injection moulding machine ARBURG 320-850-210 Multronica Screw D=40mm Locking force 85 t.Converted from floppy disk drive to CL drive Viewing by e-mail appointment is desirable Sale only to traders and under the following conditions The machine is considered to have been taken over when it leaves the company, subsequent complaints cannot be taken into account So no guarantee and return.We do not assume any liability for compliance with all requirements mentioned in the UVV (accident prevention regulations)
Two injection moulding machines are available. 1) Ferromatik K 110 1100-493, year of manufacture: 2000, clamping force: 1100kN, min. mould installation height: 300mm, max. opening stroke: 550mm, screw diameter: 40mm, injection volume: 201cm³. The control no longer starts up properly, probably due to the circuit board. Includes a 3-axis handling robot Remak. Without conveyor belt. 2) Arburg 270 M 500-90, year of manufacture: 1995, clamping force: 500kN, min. mould installation height: 225mm, max. opening stroke: 325mm, screw diameter: 30mm, injection volume: 70cm³. The cylinder is slightly leaking. Documentation available. An on-site inspection is possible.
Price 4.900+VAT (claimable)free loading on truck Injection molding machine Locking force 200t Distance between the spars 520 x 520mm Screws D.=50mm = Injection weight in hp 297gr. Machine very well preserved comes from medical equipment manufacturer Dissolution of injection molding department .with operating instructions and 2 discs. Viewing by e-mail appointment is desirable Sale only to traders and under the following conditions The machine is considered to have been taken over when it leaves the company, subsequent complaints cannot be taken into account So no guarantee and return.We do not assume any liability for compliance with all requirements mentioned in the UVV (accident prevention regulations)
R1317 Injection moulding machine ARBURG A 221 - 250 - 55 Year of manufacture 1997 Control Multronica with handling device without hopper and water distributor converted to CF drive but without card, with operating instructions for Arburg and one for the robot Machine was freed up by the purchase of new machines. but no function check from us Price free loaded on truck € 1950.-- +VAT a viewing is desirable Sale only to traders and under the following conditions The machine is considered to have been taken over when it leaves the company, subsequent complaints cannot be taken into account So no guarantee and return.We do not assume any guarantee for compliance with all requirements mentioned in the UVV (accident prevention regulations).
Special price because without dukumentation / without disc without funnel +VAT (reclaimable) R1277 Injection moulding machine Arburg A 270 Hydronica D-Version Dialogica topZustand screw D 30mm with device for injection into the parting plane a viewing is desirable by appointment Sale only to traders and under the following conditions The machine is considered to have been taken over when it leaves the company, subsequent complaints cannot be taken into account So no guarantee and return.We do not assume any liability for compliance with all requirements mentioned in the UVV (accident prevention regulations).
B&A REF: 9194 TON: 450 SCREW DIAMETER: 85MM SHOT WEIGHT: 1936 STROKE VOLUME: 2128CM3 INJECTION PRESSURE: 1354AR PLATEN SIZES: 1120 X 1120MM DBTB: 800 X 800MM MIN MOULD HEIGHT: 300MM MAX MOULD HEIGHT: 770MM MOULD OPENING STROKE: 760MM MAX DAYLIGHT: 1530MM CONTROLS: UNILOG B4 CORE PULLING: 3 AIR VALVES: 1 MOTOR: 55 HEATING CAPACITY: 48KW SCREW DRIVE: HYDRAULIC
Key data: 2000 kN, 562 g/PS, 55 mm
Specification Injection Moulding Machine Engel VC 1350/200 Tech General data Clamping force: 200 t Year of Make: 2007 Injection unit weight: 562 g Injection Unit .../1350 Screw diameter: 55 mm Specific injection pressure: 2183 bar Injection volume: 618 cm³ Injection unit weight: 562 g Tool clamping unit 200/... Clamping force: 200 t Dimensions of the tool plates: 860 x 570 mm Output force: 80 kN Tool height: 400 mm Opening travel: 750 mm Maximum panel spacing: 1150 mm Discharge stroke: 180 mm Other Specifications Weight: 14200 kg Dimensions (L x W x H): 6.3 x 1.9 x 2.3 m Year of Make: 2007 Equipment 2 x hydraulic core on the moving plate Pneumatic valve Integrated robot 8 zones for hot runners Rotameter 8-fold
Key data: 500 kN, 172 g/PS, 40 mm
Arburg Allrounder 320C 500-250 spray gossip machine
ARBURG 221 M 250-55 injection moulding machine. Clamping force 250 kN Year of construction 1996. Machine does not work. It is sold in the state as is, perhaps with its defects we don't have the skills to diagnose. It is complete, likely that repair is needed, or for replacement parts.
Injection molding machine Krauss Maffei KM 650-4300 CX BJ 2010
Injection molding machine Krauss Maffei KM 800-4300 MX BJ 2006
A two-component injection moulding machine Engel with piggyback configuration, including Engel Viper 40 robot and safety enclosure, is available. Clamping force: 1800kN, nozzle diameter: 35mm, min. mould installation height: 270mm, max. platen distance: 1020mm, tie bar spacing: 980mm, centering: 180mm. Screw diameter 1/2: 22mm/15mm, injection pressure 1/2: 2392bar/2203bar, injection weight 1/2: 66g/19.5g. Robot year of manufacture: 2014, robot travel X/Y/Z: 700mm/1300mm/2360mm. Machine dimensions X/Y: approx. 6700mm/2100mm, control: CC400, operating hours: approx. 38567h. The 22mm screw needs to be replaced. Without conveyor belt. Documentation available. An on-site inspection is possible.
Clamping force: 1500kN, screw diameter: 50mm, tie bar spacing: 500mm, platen dimensions X/Y: 780mm/790mm, opening stroke: 600mm, daylight: 900mm, ejector stroke: 150mm, shot volume: 305cm³, injection weight: 278g, injection pressure: 2336bar. Machine dimensions X/Y/Z: approx. 4700mm/1550mm/2200mm, weight: approx. 7000kg, control: MC4. Includes Sepro handling system. Documentation available. An on-site inspection is possible.
Key data: 1100 kN, 99 g/PS, 30 mm
Used Ferromatic K110D-S plastic injection moulding machine. New 2000. Technical specifications of the machine · Manufacturer: FERROMATIK MIALACRON. · Model: K110D-S. · New: 2000. · Clamping force: 1100 kN. · Injection volume: 99 cm3. · Screw diameter: 30 mm. · Maximum distance between plates: 620 mm. · Control: IQT33. · Machine weight: 5500 kg. Technical documentation. The machine is regularly serviced, fully functional and ready for operation.
Key data: 1100 kN, 254 g/PS, 45 mm
Used Ferromatic K110D-S plastic injection moulding machine. New 2000. Technical specifications of the machine: · Manufacturer: FERROMATIK MIALACRON. · Model: K110D-S. · New: 2000. · Clamping force: 1100 kN. · Injection volume: 254 cm3. · Screw diameter: 45 mm. · Maximum distance between plates: 800 mm. · Control: IQT44. · Machine weight: 5500 kg. Technical documentation. The machine is regularly serviced, fully functional and ready for use.
STVmachinery
