injection moulding machines used for sale (1,088)

Key data: 250 kN, 29 g/PS, 22 mm

Year of Make: 2005 Clamping force: 25 tons. Capacity: 38 cm³ Screw diameter: 22 mm Good condition

Key data: 450 kN, 80 g/PS, 30 mm

Year of Make: 2001 Clamping force: 45 tons. shot volume: 99 cm³ shot weight: 80 gr./PS Screw diameter: 30 mm good condition

Key data: 4000 kN, 763 g/PS, 60 mm

Year of Make: 2000 Clamping force: 400 tons. Shot volume: 848 cm³ Screw diameter 60 mm Injection pressure increased: 2,421 bar Good condition, immediately available

clamping force: 1500 kNinjection volume: 141 g/PSscrew diameter: 35 mmplaten size: 470 x 470 mmCondition: used,Specification: horizontal injection moulding machine, Type: Allrounder 470C 1500-400 GE GOLDEN EDITIONInjection unit:- Screw diameter: 35 mm (wear-resistant)- Centring ring diameter: 125 mm- Max. shot weight: 141 g (PS)- Injection pressure: 2,500 barClosing unit:- Clamping force: 1,500 kN- Max. opening stroke: 750 mm- Mould installation height: min. 250 mm- Mould clamping plates: 470 x 470 mm- Approx. operating hours: 79,000 h (still in use)- Operating voltage: 3x 400 V, 50 Hz- Nominal motor heating current: 75 / 40 A- Total current: 115 A- Total connection: 65 kW- Core pulls: 1x- Hot runner control points: 6x- Temperature control unit interfaces: ...

Ref. no.: 18643Hersteller: ARBURGYear of construction: 2008Clamping unitClamping force: 150 tonOpening stroke: 500 mmDistance between tie bars: 470 x 470 mmMould height min.: 250 mmOpening width: 750 mmInjection unitScrew diameter: 35 mmInjection volume: 154 cm³Shot weight: 141 gInjection pressure: 2500 barMeasurements and weightMachine weight: 4850 kgDimensions LxWxH part 1: 4,6 x 1,6 x 2,1 mAdditional information & extrasCore pull: 1 pcsFurther information:Communication card for ProSeS interface is available (OPC-UA).Robot interface is available (EUROMAP 67).

An old Arburg injection molding machine and five HB-Therm temperature control units are available. 1) Injection molding machine Arburg Allrounder 270S 250-70, clamping force: 250kN, tie bar distance: 270mm/270mm, platen dimensions X/Y: 380mm/380mm, mold height range: 200mm/550mm. 2) Temperature control unit HB-Therm HB-W 140, year of manufacture: 1999, max. temperature: 140°C, flow rate: 40l/min, max. operating pressure: 12bar, machine dimensions X/Y/Z: approx. 650mm/300mm/1000mm, weight: approx. 75kg. An on-site inspection is possible.

Key data: 4 kN, 70 mm

Injection Molding Machine Injection Molding Machine Manufacturer: Krauss Maffei Type: KM350 /1900 C2 Year of Make: 2005 Clamping force: 3,500 kN Tool opening force: 220 kN Driving Force Moving Plate: open: 105 kN close: 95 kN Clamping plate (h x v): 1,060 x 1,095 mm Clear width (h x v): 710 x 710 mm Tool opening travel: 920 mm Tool installation height min.: 380 mm Opening width: 1,300 mm Ejector stroke: 250 mm Ejector force forward/backward: 95 / 48 kN Pump motor: 75 kW Installed heating capacity: 30 kW Cylinder heating control zones: 6 Dry run rate: 1,550 1/h Oil filling: 720 ltr. Dimensions and weights: Net weight with control cabinet: approx. 16.0 to L/W/H: 6,510 x 2,040 x 2,380 mm Tool weight max.: 4,780 kg Injection unit: Working capacity: 1900 Screw diameter: 70 mm Spray pressure: 1,778 bar Displacement: 1,047 cm3 Shot weight for PS: 953 g I ...

Key data: 1500 kN, 415 g/PS, 55 mm

Built in 1999 Clamping force: 150 tons. Screw diameter: 55 mm Displacement: 456 cm³ Spray pressure: 1564 bar Very good condition!

Brand Ferromatik Milacron GmbH Type eQ-280 - 2290 Bj Ud Dvsw Ebpweycjlp Year of manufacturing 2023 Machine hours 50 hours Clamping Force 2.800 kN Screw ø 60 Mm Injection Pressure 2.238 bar Shotvolume max. 905 cm3 Max. distance between holms 710 x 660 mm Min. mould height 250 mm Distance between plates max. 1.400 mm Dimensions (LxWxH) 8.500 x 2.100 x 2.500 mm Weight 18.400 kG

Total connected load 21.7 kW Bj Ud Devu Dncevycolp Pump motor 18.50 KW Weight 7,400 KG

Key data: 6500 kN, 105 mm

Location is : Latino America !

B&A REF:  9237 TON: 320 SCREW DIAMETER:  70MM SHOT WEIGHT: 1078 STROKE VOLUME:  1185CM3 INJECTION PRESSURE:  1500AR PLATEN SIZES:  980 X 980MM DBTB: 650 X 650MM MIN MOULD HEIGHT:  200MM MAX MOULD HEIGHT: 730MM MOULD OPENING STROKE:  710MM MAX DAYLIGHT:  1440MM EJECTOR STROKE:  240MM CONTROLS: SEF 200 CORE PULLING: 1 AIR VALVES: 1 MOTOR: 37 HEATING CAPACITY: 22KW ROBOT INTERFACE: EUROMAP 12 SCREW DRIVE:  HYDRAULIC

B&A REF:  9222 TON: 85 SCREW DIAMETER:  35MM SHOT WEIGHT: 155 STROKE VOLUME:  170CM3 INJECTION PRESSURE:  1700AR PLATEN SIZES:  590 X 570MM DBTB: 400 X 360MM MIN MOULD HEIGHT:  150MM MAX MOULD HEIGHT: 450MM MOULD OPENING STROKE:  360MM MAX DAYLIGHT:  810MM EJECTOR STROKE:  125MM CONTROLS: DIMI EL 2000 CORE PULLING: 1 AIR VALVES: 2  MOTOR: 11 HEATING CAPACITY: 7.5KW ROBOT INTERFACE: EUROMAP 12 SCREW DRIVE:   HYDRAULIC

B&A REF:  9213 TON: 60 SCREW DIAMETER:  25MM SHOT WEIGHT: 45 STROKE VOLUME:  49CM3 INJECTION PRESSURE:  2240AR PLATEN SIZES:  446 x 446MM DBTB: 320 X 320MM MIN MOULD HEIGHT:  200MM MOULD OPENING STROKE:  350MM MAX DAYLIGHT:  550MM EJECTOR STROKE:  125MM CONTROLS: SELOGICA CORE PULLING: 1 MOTOR: 15 HEATING CAPACITY: 8.9KW SCREW DRIVE:   HYDRAULIC

B&A REF:  9224 TON: 55 SCREW DIAMETER:  32MM SHOT WEIGHT: 109 STROKE VOLUME:  120CM3 INJECTION PRESSURE:  1700AR PLATEN SIZES: 455 X 420MM DBTB: 315 X 280MM MIN MOULD HEIGHT:  120MM MAX MOULD HEIGHT: 350MM MOULD OPENING STROKE:  255MM MAX DAYLIGHT:  605MM EJECTOR STROKE:  75MM CONTROLS: DIMI EL2 PLUS CORE PULLING: 1 AIR VALVES: 1 MOTOR:  11 HEATING CAPACITY: 6KW ROBOT INTERFACE: EUROMAP 12 SCREW DRIVE:  HYDRAULIC

An Arburg injection molding machine with integrated rotary table is available. Connected load: 61kW, clamping force: 500kN, opening force: 40kN, opening stroke: 250mm, max. mold installation height: 270mm, platen distance: 520mm, rotary table diameter: 900mm, rotation angle: 180°, max. table load: 240kg, max. injection pressure: 2500bar. Machine dimensions X/Y/Z: approx. 3250mm/2000mm/2600mm, weight: approx. 3200kg, operating hours: 6244h. Documentation available. An on-site inspection is possible.

Eight Arburg injection molding machines, one Engel injection molding machine, and one Demag injection molding machine are available. 1) Arburg 270M 350-90, year of manufacture: 1996, operating hours: approx. 110000h. 2) Arburg 270M 350-90 U, year of manufacture: 1998, operating hours: approx. 108000h. 3) Arburg 270M 350-90, year of manufacture: 1992, operating hours: approx. 178000h. 4) Arburg 420C 1000-250, year of manufacture: 1995, operating hours: approx. 96000h. 5) Arburg 370C 800-225, year of manufacture: 1992, operating hours: approx. 156000h. 6) Arburg 320M 500-90, year of manufacture: 1991, operating hours: approx. 94000h. 7) Arburg 270M 350-90 U, year of manufacture: 1998, operating hours: approx. 83000h. 8) Arburg 630S 2500-675, year of manufacture: 2003, operating hours: approx. 93000h. 9) Demag Viva 100-400, year of manufacture: 1999, operating hours: approx. 116000h. 10) En ...

Injection moulding machine for food and beverages caps

Injection moulding machine for PET preforms

Clamping Force: 300 ton // Shot Weight (Max): 476 g

Clamping Force: 150 ton // Mould Height (Max): 730 mm

Clamping Force: 200 ton

Clamping Force: 350 ton // Shot Weight (Max): 694 g

Injection moulding machine for food and beverages caps

Injection moulding machine for PET preforms

Clamping Force: 420 ton // Shot Weight (Max): 1555 g

Injection moulding machine for PET preforms

Cup printing machines

Clamping Force: 1000 ton // Shot Weight (Max): 6995 g