Manufacturer:
(Category: 102-118)
Guiding and pulling spindle lathe OPTIMUM "Optiturn 4210 V" With 3 axis digital display Year of Make: 2015 Spindle bore: 54 mm Center width: 1000 mm Center height: 200 mm Speed range: 30 – 3000 rpm Stepless speed with display With the following accessories: Multifix Tool Holder Coolant Setup Three-jaw chuck 0 200 mm Four-jaw chuck 0 250 mm Collet chuck complete with collets up to 0 32 mm Feed protection Chip protection with lighting Fixed Lynette 0 approx. 150 mm Moving Lynette 0 approx. 100 mm 4 Height Adjustable Machine Shoes 1 pc. Rotating centering tip Operating instructions
turning diameter over bed: 330 mmturning diameter over slide rest: 195 mmturning length: 750 mmcenter height over bed: 160 mmcentre distance: 650 mmdigital readout: 3 Achsen HEIDENHAINbed width: 205 mmspindle bore: 36 mmspindle taper: KK5 DIN 55027turning speed range: 48 - 2500 U/minpower requirement: 3,0 kW4-jaw-chuck diameter: 160 mmquick change toolholder: MULTIFIX Typ Ataper in tailstock-quill: MK 3 dia. of quill: 40 mmquill stroke: 100 mmvoltage: 400 Vtotal power requirement: 3,2 kWweight of the machine ca.: 680 kgdimensions of the machine ca.: 1,60 x 0,80 x 1,55 m- Serial-No.: 4432- HEIDENHAIN 3-axis digital readout- MULTIFIX quick-change tool holder- Collet chuck including collets Ø 8 - Ø 27 mm- Face plate Ø 250 mm- Quick-action drill chuck- Center pointThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Tip height: 150 mm Center width: 760 mm Swivel Ø over bed/support slide: 300/165 mm Spindle bore: 32 mm Spindle holder, short taper according to DIN 55027: Gr. 5 Tailstock quill taper: MK 3 12 spindle speeds: 85 - 2000 rpm 48 feeds: 0.006 - 1.77 mm 48 metric thread pitches: 0.1 - 28 mm 58 Inch Thread: 75 - 2.5 Gg/" 19 module threads: 0.1 - 1.75 module 19 Diametrical Pitch Thread: 70 - 4 DP electr. Drive: 220/380 V, 1400 rpm, 2.2 kW Weight: 800 kg Space requirement: 1800 x 770 x 1300 mm
turning diameter over bed: 320 mmturning diameter over slide rest: 180 mmturning length: 1000 mmturning diameter in the gap: 460 mmturning speeds: 70 -2000 U/mincentre height: 160 mmspindle bore: 27 mmtotal power requirement: 2,0 KWweight of the machine ca.: 0,7 tdimensions of the machine ca.: 1,8 x 1,2 x 1,6 mCentre lathe (lead-screw and feed-rod lathe)- 160 mm 3-jaw chuck- Faceplate- Spare jaws- Quick-change tool post (base unit)- 3 tool holders- 2 steadies- Live centre- Chip trayThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Tip height: 125 mm Center width: 800 mm Gr. turning Ø over bed/over carriage guide: 280/245 mm Spindle holder, thread according to DIN 800 Spindle bore: 24 mm Spindle speeds infinitely adjustable: 26 - 2000 rpm 36 longitudinal feeds: 0.019 - 0.528 mm Metric thread pitches: 0.25 - 6 mm 44 Inch Thread: 4 - 112 Gg/" electr. Connection: 380 V, 0.7/1.4 kW Space requirements: Weight approx.: 500 kg
turning diameter over bed: 380 mmturning diameter over slide rest: 190 mmturning length: 1000 mmtotal power requirement: 4 kWweight of the machine ca.: 1,5 tdimensions of the machine ca.: 2,511,8 mTraining Machine - First-HandFeatures:3-axis digital display 3-jaw chuck4-jaw chuckCollet chuckActive chuck guardCover for lead and feed spindlesThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Year of manufacture 1980s/90s Technical data: Tip height: 185 mm Center width: 750 mm Turning diameter over bed: 370 mm Spindle bore: 36 mm Bed width: 250 mm Speed range: 38 - 1600 rpm Tailstock mount: MK 3 Quill stroke: 110 mm Dimensions (WxDxH), approx.: 1950 x 900 x 1200 mm Weight, approx.: 800 kg Equipment: - 3-jaw lathe chuck, brand: Röhm, ø 200 mm - Quick-change holder with 4 inserts - Bed stop - Chip tray
: 0400 mm: 246 mm: 1250 mm: 195 mm: 54 mm: 7,5 kWThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Key data: 230 mm, 460 mm, 25 U/min
Optimum D460x1500 lathe – fully functional Description: For sale is a used Optimum lathe D460x1500, built in 2006/01. The machine is fully functional and ready for immediate use in the workshop and production. It is ideal for turning medium-sized metal and steel parts. Technical data: Manufacturer: Optimum Model No.: D460x1500 Year of construction: 2006/01 Circumferential diameter over bed: 460–465 mm Circumferential diameter over upper slide: 270 mm Circumferential diameter without bed bridge: 690 mm Center width: 1500 mm Tip height: 230 mm Bed width: 300 mm Spindle bore: 58 mm Spindle cone: MK 6 Spindle mount: Camlock ASA D1–6 Speed range: 25 – 2,000 rpm⁻¹ Longitudinal feed: 0.031 – 1.7 mm/rev Transverse feed: 0.014 – 0.784 mm/rev Thread metric: 0.1 – 14 mm Thread imperial: 1/2 – 2 gears/inch Motor power ...
: 0460 mm: 270 mm: 1500 mm: 230 mm: 76 mm: 11 kWThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Offer 24204 Technical data: - Largest turning diameter over bed 420 mm - Center width 1000 mm - Spindle bore mm - Mounting cone of the tailstock quill MK 4 - Travel of the tailstock quill 200 mm - Spindle speeds 40 - 2000 rpm - Feeds longitudinal + flat - Metric thread pitches - Inch thread - Module thread - Drive 400 V - with: - 3 jaw chucks - SWS steel holder with 3 inserts - Space requirement approx. W 2800 x H 1250 x D 950 mm - Weight approx. 2200 kg
: neu : Bulgarien : 114970 €: 2172.93 €: 890 mm: 3000 mm: 400 mm: 155 mm: 490 mm: 700 mm: 15 : 160 MK: 24 : 160 : 0.032 - 38.9 mm/U: 0.016 - 19.45 mm/U: 0.5 - 480 mm: 60 - 1/16 Gänge/: 0.125 - 120 : 525 mm: 270 mm: 125 mm: 6 MK: 260 mm: 22 kW: 7500 kgdriven by manual transmission3-axes digital readoutquick change toolpostAmestra with 4 holders (3 square, 1 round)3-jaw chuck Bison 3204/DIN6350, Ø 500 mmspindle dead centercoolant equipmentfull length rear splash guardleadscrew and shaft protectionsafety guard for the chucktoolholder guardlevelling bolts and platestailstock quill reducerelectric motor movement of tailstocklow voltage machine lampoperating manualmachine according to ",CE",FURTHER TURNING LENGTHS: turning length1.500 mm € 100120,00 turning length2.000 mm € 103850,00 turning length4.000 mm € 123510,00 turning length5.000 mm € 134810,00 turning length6.000 ...
L+Z Lathe WEILER Praktikant 160 – Partially Overhauled Machine in very good used condition – delivery on order, delivery time by arrangement! ✅ Technical data Year of construction: approx. 1990 Digital Display: 3-Axis (NEW) Max. turning diameter over bed: approx. Ø 320 mm Max. turning diameter via support: approx. Ø 198 mm Max. turning length: approx. 650 mm Bar passage: approx. Ø 40 mm Spindle speed: 96 – 2500 rpm Spindle nose: A 2 - 5 Drive power: approx. 2.2 kW Threading: Metric, Inch, DP, Module Tailstock: MK 3 Dimensions (LxWxH): approx. 1700 x 1000 x 1700 mm Weight: approx. 650 kg ✅ Accessories 3-jaw chuck 160 mm (NEW) Quick-change steel holder + 1 insert Electric Lining Guard (NEW) Work light (NEW) Complete machine documentation Emergency stop Various tension wrenches Coolant Setup L+Z Spindle ...
: neu : Bulgarien : 81780 €: 1545.64 €: 760 mm: 3000 mm: 380 mm: 132 mm: 520 mm: 560 mm: 11 : 140 MK: 17 : 7,5 - 1015 1/min: 150 : 0.039 - 18 mm/U: 0.02 - 9 mm/U: 0.5 - 180 mm: 60 - 1/6 Gänge/: 0.125 - 45 : 410 mm: 150 mm: 105 mm: 6 MK: 225 mm: 15 kW: 4470 kgdriven by conventional transmission3-axes digital readoutquick change toolpostAmestra type Multifix with 4 holders (3 square, 1 round)3-jaw chuck Bison3295/DIN6350, Ø 400 mmspindle dead centerfour way rapid traverse devicefoot pedal brakelongitudinal stop for 1 positioncoolant equipmentfull length rear splash guardleadscrew and shaft protectionsafety guard for the chucktoolholder guardlevelling bolts and platesquick release tailstocktailstock quill reducermechanized movement of tailstocklow voltage machine lampoperating manualmachine according to ",CE",FURTHER TURNING LENGTHS: turning length1.500 mm € 67770,00 turning ...
Digital Center height 150 mm Circulation over bed 300 mm Center width 1000 mm 3-jaw chuck, Arbor Chip protection Chip tray
: gebraucht : 2015 : 1686 : prompt, Zwischenverkauf v : England : 14800 €: 1 : 330 mm: 1000 mm: 167 mm: 38 mm: 210 mm: 12 : 40 - 2500 1/min: 16 : 0.03 - 1 mm/U: 0.2 - 14 mm: 2 - 56 TPI Gänge/: 190 mm: 92 mm: 42 mm: 3 MK: 110 mm: 2.2 kW: 1940 mm: 1000 mm: 1550 mm: 685 kg3-axis digital read out Newall4-jaw chuck Bison diameter 160mm with inside and outside jawsQuick-change tool post with 1 holdCoolant deviceChuck protectionSteel holder protectionLead screw coverMachine lightManual brakeOperating manual in German with EC declaration of conformityBUYING USED MACHINERY IS A MATTER OF TRUST - OUR TRANSPARENCY PROMISEWe offer you maximum security and complete transparency.• HONEST INSIGHTS: Detailed photos and functional videos of the current condition• LIVE ON-SITE CHECK: Live testing is possible at our facility• DIGITAL DEMONSTRATION: Individual live demonstration via video call• R ...
Weiler Commodor – lead and pull spindle lathe (partially overhauled, built approx. 1990) Condition: Partially overhauled, very good general condition Year of construction: approx. 1990 Manufacturer: Weiler Model No.: Commodor Machine Type: Lead and Pull Spindle Lathe Technical data (approx. information): Max. turning diameter over bed: 380 mm Max. turning diameter over support: 190 mm Max. turning length: 1000 mm Bar Passage: 56 mm Speed range: 25 – 2000 rpm Spindle Nose: A2-6 Drive power: 4.0 kW Tailstock: MK4 Automatic longitudinal and flat feeds: 0.011 – 0.80 mm/rev Thread ranges: Metric: 0.3 – 10 mm Inch: 80 – 2 3/4 G/" Diametrically Pitch: 80 – 5.5 Dp Module: 0.2 – 5 Dimensions (L x W x H): 2200 × 1200 × 1800 mm Weight: approx. 1500 kg ⚙️ Equipment & Accessories: 3-Axis Digital Display SINO (New) ...
: gebraucht : 2023 : 1675 : prompt, Zwischenverkauf v : Bulgarien : 17600 €: 1 : 325 mm: 1000 mm: 165 mm: 32 mm: 190 mm: 200 mm: 5 : 4,5 MK: 12 : 85 - 2.000 1/min: 48 : 0.006 - 1.77 mm/U: 0.003 - 0.885 mm/U: 0.1 - 28 mm: 75 - 2,5 Gänge/: 0.1 - 1.75 : 150 mm: 95 mm: 40 mm: 3 MK: 100 mm: 2.2 kW: 2150 mm: 950 mm: 1350 mm: 770 kgdemo machine / mint conditionnet price (price for new machine € 23.970,00)driven by manual transmission3-axes digital readout Fagor 40iquick change toolpostAmestra with 4 holders (3 square, 1 round)3-jaw chuck Bison 3204/DIN6350, Ø 160 mmspindle dead centercoolant equipmentfull length rear splash guardleadscrew and shaft protectionsafety guard for the chucktoolholder guardlevelling bolts and platesquick release tailstocklow voltage machine lampoperating manualmachine according to ",CE",incl. following optional equipment:1 lenght stopBUYING USED MACHINER ...
Offer 25432 Specifications: - Turning diameter 320 mm - Center width 750 mm - Largest turn – Ø over bed 550 mm - via flat slide 175 mm - Spindle bore 32 mm - Spindle holder - Pick-up cone of the tailstock quill MK 3 - Quill stroke 180 mm - 18 spindle speeds 85 - 2000 rpm - Feeds longitudinal + flat - Metric thread pitches -Thread - Module thread - Diametrical Pitsch thread -Arbor - Cheek chuck -Lunette - Drive 400 V / 2.2 kW - Space requirement approx. W 2100 x D 750 x H 1300 mm - Weight approx. 750 kg
: neu : Bulgarien : 58370 €: 1103.19 €: 600 mm: 2000 mm: 300 mm: 80 mm: 400 mm: 400 mm: 8 : 90 MK: 3 : 20 - 100, 80 - 400, 400 - U/Min: 120 : 64 : 0.5 - 120 mm: 60 - 1/4 Gänge/: 0.125 - 30 : 315 mm: 130 mm: 90 mm: 5 MK: 230 mm: 11 kW: 3600 mm: 1500 mm: 1650 mm: 3110 kgIn contrast to the universal lathes, here the adjustment of the revolutions is infinitely variable by means of a frequency inverter.It is possible to ensure a ",constant cutting speed", (V-const), i.e. when changing the diameter to be machined, the speed remains unchanged and thus a higher accuracy and smoothness of the surface is achieved. At the customer&apos,s request, the machines can be manufactured with a reading of the linear displacement and positioning by mounting a digital display.driven by variable speed control (3 steps)3-axes digital readout Fagor with CSS (constant surface speed)quick change toolp ...
Tip height: 355 mm Center width: 3000 mm large circulation Ø over bed/recess/bed slide: 715/790/520 mm Spindle bore: 86 mm Spindle holder according to DIN 55027: Gr. 11 Tailstock quill taper: MK 5 21 spindle speeds: 5.6 - 560 rpm 42 feeds longitudinal/flat: 0.09 - 5.6/0.045 - 2.8 mm 22 Whitwort Thread: 2 - 28 Gg 28 metric thread pitches: 1 - 14 mm 27 module thread pitches: 0.25 - 3.5 module 32 module threads: 4 - 56 module 32 Diametrical Pitch Threads: 8 - 112 DP Drive motor, pole-switchable: 380 V, 7/11 kW Weight approx.: 7 t Approx. space requirement: 6000 x 2300 mm
: neu : Bulgarien : 140320 €: 2652.05 €: 1320 mm: 3000 mm: 625 mm: 155 mm: 940 mm: 700 mm: 15 : 160 MK: 4 : 3,7 - 15,6, 14,7 - 62, 58 U/Min: 160 : 0.032 - 38.9 mm/U: 0.016 - 19.45 mm/U: 0.5 - 480 mm: 1/16 - 60 Gänge/: 0.125 - 120 : 685 mm: 270 mm: 125 mm: 6 MK: 260 mm: 30 kW: 8550 kgdriven by variable speed control (4 steps)3-axes digital readout FAGOR with CSS (constant surface speed)quick change toolpostAmestra with 4 holders (3 square, 1 round)3-jaw chuck Bison 3204/DIN6350, Ø 500 mmspindle dead centercoolant equipmentfull length rear splash guardleadscrew and shaft protectionsafety guard for the chucktoolholder guardlevelling bolts and platestailstock quill reducerelectric motor movement of tailstocklow voltage machine lampoperating manualmachine according to ",CE",FURTHER TURNING LENGTHS: turning length1.500 mm € 125460,00 turning length4.000 mm € 148950,00 turning ...
Specifications: Tip height: 140 mm Turning length: 500 mm Accessories (included): Lunette Multifix "A" Collets 0.5 – 24 mm Milling device (Y-axis) 3-jaw chuck 125 mm Cs Urh Axexlr Hkszorh Face Plate 260 mm Running tip Chuck Die stock 4-jaw chuck Coolant pump Instruction manual (German)
: neu : Bulgarien : 121770 €: 2301.45 €: 1090 mm: 3000 mm: 500 mm: 155 mm: 690 mm: 700 mm: 15 : 160 MK: 24 : 160 : 0.032 - 38.9 mm/U: 0.016 - 19.45 mm/U: 0.5 - 480 mm: 60 - 1/16 Gänge/: 0.125 - 120 : 525 mm: 270 mm: 125 mm: 6 MK: 260 mm: 22 kW: 7500 kgdriven by manual transmission3-axes digital readoutquick change toolpostAmestra with 4 holders (3 square, 1 round)3-jaw chuck Bison 3204/DIN6350, Ø 500 mmspindle dead centercoolant equipmentfull length rear splash guardleadscrew and shaft protectionsafety guard for the chucktoolholder guardlevelling bolts and platestailstock quill reducerelectric motor movement of tailstocklow voltage machine lampoperating manualmachine according to ",CE",FURTHER TURNING LENGTHS turning length1.500 mm € 107020,00 turning length2.000 mm € 110650,00 turning length4.000 mm € 130410,00 turning length5.000 mm € 141610,00 turning length6.000 ...
Tip height: 195 mm Center width: 1250 mm large recirculating Ø over bed/support slide: 400/265 mm Spindle Holder/Bore: Camlock D1-6"/54 mm Tailstock quill taper: MK 5 Spindle speeds infinitely variable in 3 groups: 0 - 2500 rpm Feeds longitudinal: 0.018 - 1.2 mm Feed plan: 1/2 of the longitudinal feeds 51 metric thread pitches: 0.2 - 14 mm 56 Inch Thread: 2 - 56 Gg/" 20 module threads: 0.2 - 3.5 module 20 Diametrical Pitch Threads: 8 - 56 DP electr. Connection: 400 V, 7.5 kW Weight: 1500 kg Space requirement: 2500 x 1300 x 1300 mm
: neu : Bulgarien : 96240 €: 1818.94 €: 860 mm: 3000 mm: 430 mm: 135 mm: 620 mm: 560 mm: 11 : 140 MK: 7 - 42, 28 - 170, 165 - 1 U/Min: 150 : 0.039 - 18 mm/U: 0.02 - 9 mm/U: 0.5 - 180 mm: 60 - 1/6 Gänge/: 0.125 - 45 : 240 : 435 mm: 150 mm: 105 mm: 6 MK: 225 mm: 15 kW: 4650 kgdriven by variable speed control (3 steps)3-axes digital readout FAGOR with CSS (constant surface speed)quick change toolpostAmestra type Multifix with 4 holders (3 square, 1 round)3-jaw chuck Bison3295/DIN6350, Ø 400 mmspindle dead centermain motor with frequency invertorfour way rapid traverse devicefoot pedal brakelongitudinal stop for 1 positioncoolant equipmentfull length rear splash guardleadscrew and shaft protectionsafety guard for the chucktoolholder guardlevelling bolts and platesquick release tailstocktailstock quill reducermechanized movement of tailstocklow voltage machine lampoperating manualmachin ...
Key data: 165 mm, 330 mm, 2800 U/min
WEILER Condor lead and pull spindle lathe (overhauled) Circumferential diameter over bed 300 mm Center width 800 mm Turning diameter over carriage 170 mm Gr. workpiece weight between the tips 100 kg Bed width 240 mm Spindle bore 38 mm Spindle speeds 24 - 2800 rpm Spindle motor 3 KW Z-travel 800 mm X-travel 170 mm Z1-travel 100 mm Lead screw diameter 24 mm Thread pitches: 35 Metric 0.35 - 12 mm 40 Witworth 2 - 45 Gg / " 25 Module 0.2 - 4 Module 32 Diametrical Pitch 5 - 90 D.P. Tailstock quill stroke 110 mm Tailstock quill diameter 50 mm Tailstock quill cone 3 MK 2-axis digital display 3-jaw chuck Multifix holder B with 8 cassettes Rotating grain tip Tailstock Thread Device: Metric, Witworth, Module, Diametral Pitch Geometrically outdated!
: neu : Bulgarien : 89440 €: 1690.42 €: 760 mm: 3000 mm: 380 mm: 132 mm: 520 mm: 560 mm: 11 : 140 MK: 3 : 7 - 42, 28 - 170, 165 - 1 U/Min: 150 : 0.039 - 18 mm/U: 0.02 - 9 mm/U: 0.5 - 180 mm: 60 - 1/6 Gänge/: 0.125 - 45 : 410 mm: 150 mm: 105 mm: 6 MK: 225 mm: 15 kW: 4470 kgdriven by variable speed control (3 steps)3-axes digital readout FAGOR with CSS (constant surface speed)quick change toolpostAmestra type Multifix with 4 holders (3 square, 1 round)3-jaw chuck Bison3295/DIN6350, Ø 400 mmspindle dead centermain motor with frequency invertorfour way rapid traverse devicefoot pedal brakelongitudinal stop for 1 positioncoolant equipmentfull length rear splash guardleadscrew and shaft protectionsafety guard for the chucktoolholder guardlevelling bolts and platesquick release tailstocktailstock quill reducermechanized movement of tailstocklow voltage machine lampoperating manualmachine ...
Tip height: 175 mm Center width: 800 mm Circumferential diameter over bed: 350 mm Circumferential diameter over support: 310 mm Spindle bore: 46 mm Speed range: 25 - 2000 rpm With digital display
: neu : Bulgarien : 56920 €: 1075.79 €: 630 mm: 2000 mm: 315 mm: 103 mm: 430 mm: 400 mm: 11 : 120 MK: 21 : 12,5 - 1250 1/min: 120 : 0.04 - 12 mm/U: 0.02 - 6 mm/U: 0.5 - 120 mm: 60 - 1/4 Gänge/: 0.125 - 30 : 240 - 1 : 315 mm: 90 mm: 90 mm: 5 MK: 230 mm: 11 kW: 3310 kgdriven by manual transmission3-axes digital readoutquick change toolpostAmestra with 4 holders (3 square, 1 round)3-jaw chuck Bison 3204/DIN6350, Ø 315 mmspindle dead centerlongitudinal stop for 1 positioncoolant equipmentfull length rear splash guardleadscrew and shaft protectionsafety guard for the chucktoolholder guardlevelling bolts and platesquick release tailstocklow voltage machine lampoperating manualmachine according to ",CE",FURTHER TURNING LENGTHS: turning length1.000 mm € 53520,00 turning length1.500 mm € 54880,00 turning length3.000 mm € 61360,00 turning length4.000 mm € 67270,00 turning len ...
Make: Colchester Type / Model: Student Center width: 500 mm Passage: 42 mm Tip height: 175 mm Turning diameter over bed: 350 mm over slides: 200 mm Speed range: 34 to 1,500 mm Feed lengthwise: flat: 0.04 to 0.25 mm/rev Connection: 1.1 / 2.2 kW Accessories: Steel holder, 3-jaw chuck, 4 jaw chucks, steel bracket Weight: approx. 800 kg Dimensions: 1,550 x 900 x 1,200 mm
: neu : Bulgarien : 64180 €: 1213 €: 630 mm: 2000 mm: 315 mm: 103 mm: 430 mm: 400 mm: 11 : 120 MK: 3 : 16 - 63, 63 - 250, 315 - U/Min: 120 : 0.04 - 12 mm/U: 0.02 - 6 mm/U: 0.5 - 120 mm: 060 - 1/4 Gänge/: 0.125 - 30 : 315 mm: 130 mm: 90 mm: 5 MK: 230 mm: 11 kW: 3310 kgdriven by variable speed control (2 steps)3-axes digital readout FAGOR with CSS (constant surface speed)quick change toolpostAmestra with 4 holders (3 square, 1 round)3-jaw chuck Bison 3204/DIN6350, Ø 315 mmspindle dead centerlongitudinal stop for 1 positioncoolant equipmentfull length rear splash guardleadscrew and shaft protectionsafety guard for the chucktoolholder guardlevelling bolts and platesquick release tailstocklow voltage machine lampoperating manualmachine according to ",CE",FURTHER TURNING LENGTHS: turning length 1.000 mm € 60780,00 turning length1.500 mm € 62160,00 turning length3.000 mm € ...
Lead and pull spindle lathe WEIPERT Year of Make: 1956 Spindle bore: 90 mm Center width: 3000 mm Circulation Ø over bed : 800 mm Circulation 0 over slide: 610 mm Circulation 0 in offset: 1120 mm Speed range: 7.5 – 475 rpm With the following accessories: Multifix tool holder with 11 inserts Coolant Setup Three-jaw chuck 0315 mm Three-jaw chuck 0 400 mm Three-jaw chuck 0 500 mm Face Plate 0 400 mm Face Plate 0 800 mm Face Plate 0 1000 mm Running Lynette Various turning tools (30 pcs. indexable insert tools) 2 moving centering tips 1 drill chuck Operating instructions
: neu : Bulgarien : 126650 €: 2393.69 €: 890 mm: 3000 mm: 400 mm: 155 mm: 490 mm: 700 mm: 15 : 160 MK: 4 : 3,7 - 15,6, 14,7 - 62, 58 U/Min: 160 : 0.032 - 38.9 mm/U: 0.016 - 19.45 mm/U: 0.5 - 480 mm: 60 - 1/16 Gänge/: 0.125 - 120 : 525 mm: 270 mm: 125 mm: 6 MK: 260 mm: 30 kW: 7500 kgdriven by variable speed control (4 steps)3-axes digital readout FAGOR with CSS (constant surface speed)quick change toolpostAmestra with 4 holders (3 square, 1 round)3-jaw chuck Bison 3204/DIN6350, Ø 500 mmspindle dead centercoolant equipmentfull length rear splash guardleadscrew and shaft protectionsafety guard for the chucktoolholder guardlevelling bolts and platestailstock quill reducerelectric motor movement of tailstocklow voltage machine lampoperating manualmachine according to ",CE",FURTHER TURNING LENGTHS: turning length1.500 mm € 111610,00 turning length2.000 mm € 115430,00 turning ...
This offer is aimed exclusively at entrepreneurs within the meaning of § 14 BGB. The price is net plus 19% VAT. Manufacturer: EST Ticino Type: ET-BM 400 Turning length: 1500 mm Turning diameter bed Ø: 800 mm Turning diameter slide: 470 mm Turning diameter pit Ø: 400 mm Pit length: 750 mm Spindle bore: 130 mm Power spindle: 15 kW Bed width: 600 mm Quill: 130 Ø Stroke quill: 300 mm Spindle mount: 6 Mk Speed: 600 rpm Dimensions (estimated) Length: 4500 mm Width: 1800 mm Height: 1800 mm Weight: 5200 kg with accessories: -Safety equipment - Face plate, four-jaw chuck, clamping jaws, tool holders, tips, drill chucks, tools All information is made to the best of our knowledge, errors excepted. The sale is subject to exclusion of any warranty. The exclusion does not apply to claims for damages arising from grossly negligent or intentional breach of the S ...
turning length: 750 mmturning diameter: 310 mmturning diameter over slide rest: 175 mmspindle bore: 32.0 mmtailstock quill taper MT: 3 MKturning speeds: 85 - 2200 U/minbed width: 200 mmspindle taper: DIN 55027 GR 5 total power requirement: 2.2 kWweight of the machine ca.: 710 kgrange L-W-H: 1884 x 717 x 1262 mm New price ~ 20.000 euros from a technical college ()- in checked condition - machine videos -https://www.youtube.com/watch?v=iqU7Bkh6INohttps://www.youtube.com/wa tch?v=aSViqjk51IkFurnishing:- Robust conventional center lathe- 3-jaw lathe chuck Ø 160 mm, with replacement jaws- NEWALL digital display, front left- MULTIFIX steel holder with 4x inserts- fixed bezel- moving bezel- Movable tailstock- Foot/spindle brake- Machine swing feet- User manual (PDF/NL) all technical data:- Turning diameter over bed 310 mm- Distance between centers 750 mm- Turning diameter over support 175 mm- ...
Key data: 180 mm, 2000 U/min
Built in 1990 Center height 180 mm Turning diameter over carriage 190 mm Center width 1,000 mm Spindle passage 55 mm Max. spindle speed 13-2,000 rpm Spindle drive 7.5 kW Quill stroke 150 mm (MK4) Machine weight 1,650 kg Accessories: Digital display, 3-jaw chuck, quick-change steel holder with 4 inserts, 2 steady rests, coolant device.
: neu : ca. 4 Monate ab Auftragse : Bulgarien : 86980 €: 1643.92 €: 860 mm: 3000 mm: 430 mm: 132 mm: 620 mm: 560 mm: 11 : 140 MK: 17 : 7,5 - 1015 1/min: 150 : 0.039 - 18 mm/U: 0.02 - 9 mm/U: 0.5 - 180 mm: 60 - 1/6 Gänge/: 0.125 - 45 : 240 - 2/3 : 435 mm: 150 mm: 105 mm: 6 MK: 225 mm: 15 kW: 3470 mm: 1700 mm: 1730 mm: 4650 kgdriven by conventional transmission3-axes digital readoutquick change toolpostAmestra type Multifix with 4 holders (3 square, 1 round)3-jaw chuck Bison3295/DIN6350, Ø 400 mmspindle dead centerfour way rapid traverse devicefoot pedal brakelongitudinal stop for 1 positioncoolant equipmentfull length rear splash guardleadscrew and shaft protectionsafety guard for the chucktoolholder guardlevelling bolts and platesquick release tailstocktailstock quill reducermechanized movement of tailstocklow voltage machine lampoperating manualmachine according to ",CE",F ...
Tip width: 430mm Tip Height: 120mm Spindle bore: 23mm Spindle speeds: 60-3000 RPM Short taper spindle head DIN 4 Tailstock MK2 Feeds from 0.03 to 2.5 mm Weight approx. 360 kg New Aikron 3-axis digital display, brake of spindle motor renewed, technically checked. Accessories: Collet device, lathe chuck Quick-change steel holder
turning diameter: 360 mmturning length: 1000 mmswing diameter over bed slide: 215 mmreus: 30 - 3000 U/minspindle bore: 38 mmfeed: längs 0,043 - 0,653 m/mintotal power requirement: 3,5 kWweight of the machine ca.: 1500 kgdimensions of the machine ca.: 1900 x 900 x 1300 mmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Center distance 5,000mm Height of the tips 600mm 105mm bar passage carriage equipped with grinding Machine in very good condition
turning diameter over bed: 340 mmturning diameter over slide rest: 260 mmturning length: 700 mmspindle bore: 48 mmspindle turning speed range: 25 - 2000 U/minspindle nose: DIN 55027 KK 5voltage: 380 Volttotal power requirement: 2,2/4,4 kWweight of the machine ca.: 1000 kg.dimensions of the machine ca.: 1.800 x 700 x 1.500 mmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Center distance 11,000 mm Turning diameter 730 mm Drill height 500 mm turnable on the bench 1050 mm Motor power 22 kW
turning diameter over bed: 400 mmturning diameter over slide rest: 245 mmturning length: 800 mmtotal power requirement: 4.5 kWweight of the machine ca.: 1.25 trequired space: 1.96x1.69x1.06 mThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Offer 24177 Specifications: - Tip height 180 mm - Center width 1000 mm - larger circulation – Ø over bed 355 mm - via flat sleds approx. 200 mm - Spindle bore 36 mm - Pick-up cone of the tailstock quill MK 5 - Travel of the tailstock quill 260 mm - Spindle speeds 18 - 1800 rpm -Feeds - Travel of the cross slide approx. 200 mm - Travel of the upper slide approx. 115 mm - Drive 400 V / 5.8 kW - with: - Tailstock, 3-jaw lining, bezel - Steel holder, moving center punch, - Chip tray - Space requirement approx. W 2500 x H 1500 x D 1200 mm - Weight approx. 2100 kg
turning diameter: 760 mmturning length: 3000 mmswing diameter over bed slide: 520 mmcentre height: 380 mmreus: 17 (7,5 - 1015) U/mintail stock: MK6 quill stroke: 225 mmdiameter of quill: 105 mmspindle bore: 132 mmfeed: längs 0,039 - 18 mm/minfeed: quer 0,02 - 9 mm/mintotal power requirement: 15 kWweight of the machine ca.: 4700 kgdimensions of the machine ca.: 4900 x 1650 x 1650 mm- Coolant device- Machine light- Chip back wall- Spindle protection- Lathe chuck protection- Tool holder protection- Interchangeable gearsSpecial equipment- 3-jaw chuck Ø 250 mm type 3204/ DIN6350, BISON- MULTIFIX quick-change holder type B, including 4 tool holders- 3-axis digital display DRO Newall- Foot pedal with brake function CEThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Tip height: 205 mm Center width: 1500 mm Circumferential Ø: over bed 410 mm Spindle bore: 47 mm Spindle holder: size 6 Pick-up cone tailstock: 4 MK Spindle speeds: 28 - 1250 rpm Feeds: longitudinal/flat 0.03-1.3/0.008-0.33 mm/rev Thread pitches: 0.25 - 76 mm Electrical connection: 380 V, 3 kW Space requirement: 2800 x 1100 x 1600 mm Weight: 1330 kg
turning diameter over bed: 500 mmturning diameter over slide rest: 300 mmturning length: 1000 mmtotal power requirement: ? kWweight of the machine ca.: 1,5 tdimensions of the machine ca.: 2,511,5 mThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Tip height: 250 mm Center width: 2000 mm Circumferential Ø: over bed 500 mm Spindle bore: 50.8 mm Spindle holder: size 6 Pick-up cone tailstock: 5 MK Spindle speeds: 22 - 2000 rpm Feeds: longitudinal/flat 0.05-6.4/0.025-3.2 mm/rev Thread pitches: 80 - 1 mm Electrical connection: 380 V, 5.5 kW Space requirement: 3600 x 1100 x 1500 mm Weight: 1875 kg
: gebraucht : 2020 : 1658 : prompt, Zwischenverkauf v : Bulgarien : 26500 €: 1 : 22600 €: 400 mm: 1000 mm: 200 mm: 52 mm: 235 mm: 320 mm: 6 : 6 MK: 12 : 50-2.240 1/min: 80 : 0.015 - 0.6 mm/U: 0.0075 - 0.3 mm/U: 40 : 0.25 - 7.5 mm: 120 - 4 Gänge/: 0.0625 - 1.875 : 235 mm: 110 mm: 50 mm: 4 MK: 100 mm: 4 kW: 2750 mm: 1100 mm: 1600 mm: 1540 kgThis machine is used in our workshop for repair work,therefore it has only been used very little so far.(New price € 37,910.00)driven by manual transmission3-axes digital readout Fagor 40iquick change toolpostMultifix Type Bwith4 holders (3 square, 1 round)3-jaw chuck Bison 3204/DIN6350, Ø 200 mmspindle noseNr. 6 DIN 55027four way rapid traverse devicespindle dead centercoolant equipment1 pce. flange plate for lathe chuckØ 200 mm1 adapter sleevefull length rear splash guardleadscrew and shaft protectionsafety guard for the chucktoolholder guard ...
