136,416 used machines on RESALE, but how to find them? Machine Search
Roller spreader for rear mounting, drive via a 12 volt electric motor with overload protection (8 A). Container contents 120 ltr. , cam roller with interchangeable, asymetric cams (suitable for sand, salt and shards or granules)Roll width 125 cm, stirring shaft to prevent lump and bridge formation, low-wear 10-stage scattering volume regulation by adjustable spring bottom with rubber apron. With grating for accident protection and cable remote control (start/stop). Without growers! Scattering length salt approx. 5-6 km, sand approx. 1 km (manufacturer specifications) Built in 2012, unused, technically and visually as new condition, here and there paint somewhat repelled. Other roller spreaders, also trailers, self-loaders, drive hydraulic, PTO shaft or wheel stock. Winter service technology of all kinds, also slingshot spreaders, snow shields, snow blowers, tractors and used compon ...
The machine packs in full cartons or trays. Capacity up to 80 cartons per minute. The change to the new carton format takes place from the operator panel - very quickly. Siemens S-7 control. Machine dimensions: Length: 9m Maximum width: 3.2m Height: 2.4 m. Weight: 3.5 tonnes The machine is equipped with a set of necessary spare parts for 2-3 years of operation. The machine after complete renovation in very good condition. Ready to work. We provide 12 months warranty. The condition of the machine and the level of modernity ensure many years of operation.
Key data: 40 , 200 , 1340
The all-electric servo bending machine is one of the products with independent intellectual property rights developed by our company. Special high-load screw and guide rail structure, imported bearing installation, high load-bearing capacity, high positioning accuracy, long life, machine tool rigidity, precision retention, and reliability are close to perfection. By introducing advanced design concepts and scientific design methods, the shortcomings that traditional designs cannot avoid have been solved. This bending machine is fast and simple to program, can realize concurrent linkage of multiple axes, fast feed positioning, and significantly improves the efficiency, accuracy and consistency of bending, which is far superior to traditional hydraulic bending machines, and does not require the use of hydraulic oil, is environmentally friendly and pollution-free. Compared with traditional ...
Weibert FR3 Saw milling Demonstration device Format sliding table 2300mm or 2600mm Cutting height: 103mm Auslegertich kpl. Saw blade: swivel, max.315mm 3KW motors Milling: rigid 90° Milling rpm: Speeds: 1500/3500/6000/8000 rpm. Safety rails milling stop 500mm Right- and left-hand-running milling cutter WJ-400100
Key data: 420 mm, 650 mm
Machine Type: CNC Lathe Manufacturer: Okuma Type: LB400M-1SC Year of Make: 2000 Commissioning: 2001 Control: OSP-U100L Spindle hours: 14502 hrs Delivery time: in stock Machinery - Interior extraction from Hengst Filtration (built in 2023) - Touchsetter, tool measurement - C-axis (main spindle) - Tool breakage and wear monitoring - 3-jaw chuck, Kitagawa B210, Ø250 - Tailstock available - Coolant supply, also available through the tool - Dialogue programming IGF - Chip conveyor (scraper) Technical details - Max. turning length: 650 mm - Max. turning diameter: 420 mm - X-axis travel: 300 mm - Travel Z-axis: 675 mm - Travel C-axis: 360° - Chuck passage: 72 mm - Spindle passage: 95 mm - Clamping cylinder passage: 95 mm - Tool holder: VDI 40 - Tool stations: Stations 12 - Spindle speed: 2800 rpm - Main spindle power: 22/30 kW - M-spindle ...
Key data: 370 mm, 600 mm
Machine Type: CNC Lathe Manufacturer: Okuma Type: LU300-2ST Year of Make: 2005 Control: OSP-E100L Delivery time: in stock Machinery Parts conveyor belt and parts collection tray – workpiece chute with removal conveyor belt incl. electrical kit 2 disc turret with VDI40 (12 + 8 stations) Power clamping cylinder for hollow chips – Hole in the drawbar 52mm Extension Kit "D" – Kit one touch IGF-D Open/close chuck while the spindle is running via M-Code Reinforced coolant pump 8 bar Coolant on A and B turrets can be switched via M function Interface for connecting rod feed Chip conveyor Technical details Swing diameter over bed: 530mm Swing diameter over slide: 380mm Distance between the tips: 600mm Max. turning diameter: 370mm Max. turning length: 600mm Travel X-axis: upper 260mm ...
Key data: 340 mm, 1000 mm
Machine Type: CNC Lathe Manufacturer: Okuma Type: LU15-M Year of Make: 2000 Control: OSP-U100L Country of origin: Japan Delivery time: in stock Long turning length-1000 mm Towable Tailstock – Automatic G152 Partial hollow clamping device The lathe is in very good condition. The basic and additional equipment makes it possible to process long turning lengths of up to 1000 mm with this used machine. Effective productions continue to be achieved thanks to the towable tailstock – automatic, the tool breakage/wear control, the partial hollow clamping device, the K-pump and the dialogue programming (IGF). An optimal machine for economical and reliable production. The machine is user-friendly and can be integrated into production immediately. Machinery Spindle motor VAC built 22/15 kW Long turning length – 1000 mm towable tailstock – automatic G152 3-jaw chuck Forka ...
Technical data: Maximum parent roll width: 1420 mm Minimum parent roll width: 600 mm Maximum parent roll diameter: 1500 mm Maximum parent roll weight: 2500 kg Maximum unwinding tension (Ø1500 mm): 600 N Minimum unwinding tension (Ø1000 mm): 40 N Minimum standard slitting width: 100 mm Maximum rewinding width: 1400 mm Maximum rewinding diameter: 1050 mm Maximum rewinding weight: • Ø76 mm shaft: 600 kg • Ø152 mm shaft: 1000 kg Maximum rewinding tension: 600 N Maximum production speed: 600 m/min Power supply: 3 x 400V 50Hz Installed power: 30 kW Compressed air: 6 bar, dry Materials to be slit: • Paper-based / liner-based packaging laminates. • Board from 80 to 300 g/m². Unwind section: A separate between-centers unwinder, type T9, 1500 mm diameter, including: • Hydraulic cylinder control for lifting parent rolls from the floor. • Two motors driving th ...
[ 5000 characters max., no information about the advertiser ] Brand:MODUL Model:ZFWZ 2000/3 Type:Gear Hobbers Year:1981 Location:Czech Republic Specification: Max diameter of gear without tailstock 2100 mm Max diameter of gear with tailstock 1450 mm Max face of gear 1060mm Max module with hobbing head 22 Max/ Min center distance 1240/150 mm Min number of teeth 10 Max pressure angel 45 deg Table dia / number of slots 1800 mm/12 Bore in table / length 600/800 mm Max dia of hob / length 300/330 mm Max weight of workpiece 15000 kg Accessories: Standard milling head Tailstock (no clamping) Set of gear supports (shoes) Set of arbors Set of change gears
Showroom machine / exhibition machine CMS Tecnocut - IDROLINE S 2040 Axle experience: X-axis: 4,250 mm Y-axis: 2,000 mm Z-axis: 200 mm C-axis: endless B-axis: +/- 60° Facilities: - 5-axis cutting head JD5Ax for inclined cuts up to 60° and automatic angle correction - Chain conveyor for automatic sand application - Automatic lifting doors to secure the working area - Sand dosator for automatic software controlled sand dosing - Central lubrication - Altitude probe with anti-collision system High pressure pump Greenjet Electric high-pressure pump with directly controlled servo motor Total current consumption: 34 kW at 5 ltr. / min Power connection: 400 V +/- 5% / 50 Hz Max water pressure 4,150 bar Pressure vessel 1.2 ltr Water passage: max. 5 ltr. / min DÃ?SE: 0.40 mm max. Incl. assembly / training and 12 months warranty!
KRONEN AS 4 APPLE PEELING, CORING AND CUTTING MACHINE Manufacturer: KRONEN Model: AS 4 Year: 2017 Serial no.: 175012 Multipurpose semiautomatic apple processing machine designed to peel, core and cut apples into segments and slices of different sizes (depending on the cutting accessories that are used). It is capable of processing up to 3 apples at the same time. Made of stainless steel Max. capacity: 600 apples/hour (approx. 90 kg/h) Apple size: Ø 55 - 85 mm Electrical data: 230 V/50 Hz/0.18 kW/1PH Overall dimensions (mm): 300 x 660 x 400 (WxLxH) Weight: 35 kg The following cutting accessories are included: - Ø 23 mm corer - Blades for cutting into 10 and 24 segments
McIntyre Euro-strip 500 Cable Stripper The perfect bench-top cable stripper. Compact and efficient The Euro-strip 500 is one of the smallest in the range and is a low energy, large capacity unit that is easy to move around a yard. The Euro-strip Cable strippers are designed for simple, dependable operation without the need for constant adjustment, which suits all different material sizes. Taking up minimal space and emitting very low noise, the Euro-strip 500 will prove to be a valuable addition to your business.
Manufacturer: ESC – Europa-Siebdruck-Centrum GmbH & Co. KG Model designation according to nameplates: PAJD 1100-2C/IR and Perfection 1100 2C/IR Year of manufacture according to nameplates: 2016 and 2017 Machine/Factory Numbers: 9960-14-1065 / 11661 Electrical connection: 400 V, 50 Hz Rated current: 120 A (nameplate PAJD) Nominal power: 76 kW (Perfection nameplate) Degree of protection: IP40 Belt type: IR temperature tunnel with conveyor belt (width according to series: 1100 mm) Assembly: IR drying system for screen printing or varnishing processes Design: Closed safety enclosure with access doors Application: Drying/shortening of printed or coated components Location: Schierling Viewing possible by appointment.
Wabäma Economy Plus bread cutting machine with long bread inserting tray suitable for 52cm of bread. -with sickle knife -with oiling -Built in 2007 -Cutting width adjustable -three-phase current 400 volts -Rated power 1.9 A -Control voltage 24 volts -Operating voltage 24 volts -Weight 285 kg
CMS Tecnocut Easyline Cutting range / axis experience: X-axis: 2,000 mm Y-axis: 4,000 mm Z-axis: 150 mm Uiaw3u8 C-axis: 630° B-axis: +/- 60° Included equipment: - 5-axis snow head incl. angle correction - Sand dosing and vacuum monitoring - Height scan - CAD/CAM - Laser - Central lubrication CMS Tecnocut GREENJET Highly efficient electric high-pressure pump. Technical data Total current consumption: 34 kW at 5 ltr. / min Power connection: 400 V +/- 5% / 50 Hz Max water pressure 4,150 bar Pressure vessel 1.2 ltr Water passage: max. 5 ltr. / min Opening diameter DÃ?SE: max. 0.40 mm The pressure translator with directly driven servo motor offers the following advantages: + Energy efficient + Proportional power consumption + no maintenance-free hydraulics + 75 dBA + Low maintenance due to 60% less structural components + internal water pump + ...
Rego SM4 Stroke Machine Stirring Machine for 40 Liters For sale is a Rego SM4 stirring and stirring machine, a robust and powerful device for bakers. The machine is ideal for whipping and stirring various creams and light doughs. Rego SM4 Stroke and Stirring Machine - Manufacturer: Rego Herlitzius - Model: SM4 - for mixing, kneading, beating and stirring a wide variety of masses (e.g. doughs, creams, shames, etc.) - for a maximum of 40 litres - Speed adjustable - 2 working functions, stirring or beating - Boiler lighting - With EMERGENCY stop button - incl. 2 whisks + 1 kettle Technical data and dimensions: - Connection 400V, 16A plug - Power: 1.6 kW - Dimensions: 720 x 680 x 1710 mm, WxDxH - Weight approx. 285 kg The machine can be visited and tested by appointment. More information and pictures as well as delivery on request.
Below you can see the first impressions of our mobile screening machine, which was designed for separation tasks in the outdoor area. The system can separate different types of material into two fractions, depending on the selection of the mesh widths, the degree of the sifted material can be adjusted. The two fractions are discharged into wheelbarrows via the outlets of the screening machine. For the removal of fine goods, the stern must be removed. The coarse material enters another wheelbarrow or a suitable container via a second slide. The mobile screening machine can be rented and purchased. Ready to drive 450Kg
1 of used film-only multi-packer, make KHS, type Innopack Kisters SP 050 B2, new 2013. Operating side: links. Used for PET bottles 250/500 ml as 3x2=6-packs (dual lane) and 6x2=12-packs as well as 6x4=24-packs (single lane) in clear or print-registered film. Quick change-over via servos and spindles. Capacity upto 50 cycles per minute. Siemens S7 controls.
Soehnle Professional 2790 Weighing Terminal Floor Scale 9013 The SOEHNLE 2790 display unit is very handy and also protected according to protection class IP65, which means that it can also be used in wet areas without any problems With only five buttons, the SOEHNLE 2790 digital display device is particularly easy to operate. The built-in functions are on/off, tare, clear tare, zero and print. In addition, the 2790 indicator also has a piece counting function. The SOEHNLE 2790 display unit can be operated not only with the 230 V power supply included in the scope of delivery, but also with batteries for up to 100 hours independently of the mains. The 20 mm high digital display is backlit when plugged in and is therefore particularly easy to read. In battery or battery operation, an automatic switch-off can also be set to protect the batteries and batteries. Soehnle ...
Ger RHC1500 Universal Rectifier. Indoor head. Distance between points: 1500mm. Maximum part diameter: 355mm. Point height: 180mm. Tooth diameter: 400mm. Power: 7.5hp. Weight: 4500Kgs.
Parts cleaning system Industrial washing machine degreasing made entirely of stainless steel! Manufacturer Render Type W175 Built: 1994 5 loading trolleys with 5 washing baskets, Basket size 1,125 x 1,125 mm Manual workstation with viewing window on one side with integrated high-pressure cleaner. Machine to be loaded/unloaded from both sides! Machine comes from an operating resolution and was in use until dismantling. Tank capacity approx. 2,000 litres, oil scimmers, filters, high-pressure pumps... Vertical door opening (lifting doors) on two opposite sides. This allows you to load on one side and unload on the other side. Due to the very high inner height, the system offers an optimal possibility to accommodate both very heavy laundry material as well as parts with large dimensions.
No 2 circular blades motors HP 3 - 2800 rpm No 5 drilling units motors HP 1 - 2800 rpm No 1 conveyor belt feeding machine HP 0,5 - 1400 rpm Pneumatic movements with hydraulic brake Stacking / Destacking device with pneumatic cylinders Electro-pneumatic machine control with PLC: Overall dimensions: -Length Mm: 2500 (useful for cutting and drilling) -Height Mm: 1400 -Width Mm: 1800
Hydraulic rescue scissors operated with hydraulic pump (630bar) internal combustion engine. To be used as e.g. cable scissors for use in areas without power supply. 1 fuel-powered hydraulic unit 1 hydraulic scissors 1 hydraulic spreader Npjrx All the goods in very good, ready-to-use condition.
Band saw Jespa 340/630 HAP column guided Band saw Jespa Semi-automatic Type 340/630 HAP Column-guided Built in 2009 Saw blade length 5.150mm
Milling machine from a training workshop in very good condition Manufacturer lid Type FP1 Active
running direction: right - left for 28 mm VacuVent closure with safety housing
DIGI SM-5500B System Scale SM-5500B, the advanced PC-based system scale printer that provides you with multiple retail solutions. Increases operating revenue, improves operations with integrated queuing and collection system through various innovative features of the SM-5500B. Experience real retail solutions offered by DIGI's PC scales. • Linerless printing with integrated automatic cutting device • Watermark printing • Speed ID • InfoTag and electronic signage e.Label • Integrated queuing and collection system •Waste management • Interactive screen display Power source 230 V (50/60 Hz.) Operating Humidity 15% - 85% RH Non-condensing Operating temperature -10° C to +40° C Operator display 12.1" Customer Display 7"WVGA (800x480) Interface RS232C, Ethernet (standard) max. 15/30 kg, min. 100g, e = 5/10g, Dimensions (in mm) 385(W) x 507(D) x 148(H) ...
Pass width mm: 1300 02 Engines KW: 1 + 1 02 Brushes Brush diameter mm: 300 Vacuum table Control cabinet KW: 8.5
Grinding units Grinding belt length mm: 8000 Grinding width mm: 120 Feed max: 2200 m/min Manipulation unit Max machining range mm: 2100x650x400 Total connection kW: 7.2
General Manufacturer: Stama Type: MT 733 two Year of Make: 2020 Control: Siemens Sinumerik 840D SL Travel: X 615 mm Y 290 mm Z 500 mm Rapid traverse: 65 m/min Feed: x 4,000 N / Y 4,000 N / Z 8,000 N Main spindle unit Speed: 12,500 rpm Tool holder: HSK-T63 Pull-in force: 18 kN Spindle bearing diameter: 80 mm Tool magazine Number of available magazine slots: 64 Tool diameter max. when fully equipped: 78 mm Tool diameter max. with free secondary positions: 140 mm Tool length: max. 300 mm Tool holder: HSK-A/T63 Tool weight: max. 10 kg Total chain load: max. 115 kg Rotary swivel unit Swivel angle: +30 to -180° Swivel axis repeatability: ±1" Swivel axis speed: max. 61 1/min Clamping torque tangential swivel axis: 3,000 Nm Clamping torque tangential counter bearing: 1,800 Nm Condition Condition: Used Functional: tested and fully functional
Grinding width mm: 1350 Pass-through height mm: 3 - 160 Feed max m/min: 2 - 20 - Inverter KW 3 01 Grinding unit: Grinding belt length mm: 1380 x 3250 - 24 SH - 15 KW Blow-off device Vacuum table Scotch Brite x mm 200 Machine Control: Viet "IPC 15" Touch Screen Centering device Weight Kg: 3970
Pass height max mm: 2000 Battery: 24V Chargers: automatic and high-frequency Automatic reading of the charging height: Reflective light barrier Total power: 0.75 KW
Heid S-200 CNC Lathe Manufacturer: Heid Type: S 200 Machine Type: CNC Lathe Tailstock travel: 175 mm Tailstock quill holder: Morse cone: 4 MK Quill stroke: 140 mm Quill diameter: 95 mm Pressure capacity: 17 kN Connection 50 Hz 3x: 380 Volts Total power requirement: 65 kVA Spindle speeds: Infinitely variable from 0 rpm to: 4000 rpm Spindle bore: 77 mm Tool shank cross-section: 25x25 mm Turning diameter above the bed: 420 mm Turning diameter maximum: 250 mm Turret slide: Longitudinal travel (Z-axis): 1150 mm Flat travel (X-axis): 230 mm More items - new and used - can be found in our shop! International shipping costs on request!
Grinding width mm: 1350 Pass-through height mm: 3 - 160 Feed max m/min: 2 - 20 - Inverter KW 4 01 Grinding unit: Grinding belt length mm: 1380 x 3250 - 15 KW (INV) 01 Orbital grinding unit "Spinbrush" - KW 4 (INV) 01 Grinding unit: Grinding belt length mm: 1380 x 3250 - 15 KW (INV) Machine Control: Viet "IPC 15" Touch Screen Blow-off device 1 Blow-off device 2 Vacuum table Scotch Brite Weight KG: 7200
Description Seiger lathe SLZ 800E x 4000 Details Machine no. 4443 Year of construction 2008 Siemens Cycle Control Spindle holder according to DIN 55027 size 11 Spindle bore Ø 130 mm Spindle diameter in the front bearing 170 mm Spindle taper 1:20 Drive power 20/28 kW Main spindle speed switching stage "I" 9-1,800 min-1 Main spindle speed switching stage "II" 9-400 min-1 Maximum torque: 3,200 Nm Center width 4,000 mm Circulation Ø above the bed 810 mm Circulation Ø above the face slide 540 mm Bed width 480 mm Machine dimensions 2,000+center width x 2,750 x 2,000 mm Permissible workpiece masses between points without setting stick 2,000 kg Permissible workpiece masses between points with a setting stick 2,200 kg Permissible workpiece masses between tips with two setting sticks 2,500 kg Permissible workpiece masses flying i ...
Travel x 350 mm y 250 mm z 220 mm Water bath machine Automatic wire threading Glass scales x / y incl. box for large coils incl. cooler incl. functional guarantee
Sweeping width mm: 880 Number of brushes: 2 Weight: Kg 646 Total connection KW: 3
Description Heyligenstaedt Lathe NDb-630 Details Year of manufacture 1980 Tip height above bed 630 mm Turning length 3,000 mm Turning diameter over bed 1,240 mm Turning diameter over bed slide 960 mm Max. workpiece weight without support 10,000 kg Bed width over guideways 850 mm Number of guideways 2 Bed height 650 mm Slide path 3,000 mm Face plate diameter 1,100 mm Main spindle diameter in the front bearing 280 mm Max. torque at the face plate 25,000 Nm max. workpiece weight clamped on the fly at center of gravity distance 250 mm in front of face plate 4,000 kg Main spindle speed range 2.24 - 450 rpm. Number of main spindle speeds 4 mech. Levels Power main motor 50 kW Main motor speed 100-1,000-2,500 rpm. Number of supports: 1 Cutting force support 4,000 kg Guide length front bed track 1,300 mm Quill diameter 250 mm ...
used vertical hydraulic internal clearing machine with 3 clearing points in very good condition Pulling power:8.000 KG Clearance length: 1000mm Bgno2qtoyx Clearing: 3 pieces (4 pieces) Distance between clearing points:100mm Mounting diameter of the drawing heads3 x x 85mm Workpiece diameter: max. 1x 460mm / 2x 198mm / 3x 98mm Cutting speed: hydraulically infinitely adjustable from 1m/min up to max. 7m/min Return speed: hydraulically infinitely adjustable from 5 to max. 25m/min Space requirement of the machine (b x t x h) approx.:1400 x 2000x 3600mm (without service & operator environment) Power supply / connection value: 380Volt 50 HZ / 6.5 KW Accessories / Optional equipment: -manual and automatic clearing operation - Drawbridge for 3 clearing points - Workpiece table for 4 clearing points (only usable with special pullheads) - automatic tool feeder - tension dis ...
Ceever Spraymaster Turning Spray Washer The Spraymaster series of industrial washing systems are advanced solutions for spray cleaning of small and medium-sized components with a capacity of up to 4000 kg. Thanks to a rotary table that allows the parts to be evenly wetted with the spray jet, these systems ensure maximum effectiveness in surface treatment. Inside the treatment chamber, a channel system with strategically positioned nozzles allows for complete spray cleaning of all surfaces, optimizing chemical, mechanical and thermal processes in a single operation. Manufacturer: Ceever Type: Spray Master Turning Machine No. Z 429 Loading: 500 kg/batch Voltage: 380 volts Current consumption: 90 A Connected load: 62 kW More items - new and used - can be found in our shop! International shipping costs on request!
Woelfel B100/S used machine Spindle dia 125mm MK 6 Ram dia 165 mm with stroke 200 mm Spindle speed in 24 steps from 30 - 1200 rpm Vert. travel of headstock 1250 mm Bed clamping surface 870 x 700 mm Additional table 710 x 560mm height 500 mm Height between bed and spindle nose 1460 mm
4 Belt grinding unit 2 grinding brushes Carpet length mm: 5500 Carpet width mm: 400 (extendable) Weight Kg: 800
Dimensions (L/W/H): 2150x1300x1780 mm Weight: 1000 kg Total power requirement: 5,5 kw The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
GM-SB-38CNC-2A1S mandrel bending machine was built in 2022 in China by ZHANGJIAGANG KING-MACC MACHINERY MANUFACTURING CO., LTD. The machine is used for precision bending of bars, profiles and tubes with a maximum diameter of 38 mm. The process is performed by means of a reliable working head, operating in manual or automatic mode. In order to guarantee high positioning dynamics combined with excellent positioning accuracy, all axes are equipped with powerful servomotors. Ease of operation is ensured by a convenient operator panel with PLC control. Its large memory enables the storage of up to 200 working programmes, as well as the rapid programming of even the most complex shapes. All this makes the GM-SB-38CNC the perfect solution for any production facility. The GM-SB-38CNC-2A1S tube and profile bending machine weighs 2000 kg. Technical specifications of the GM-SB-38CNC-2A1S tube be ...
sheet metal cleaning machine from Schlee. The machine was built in 2011. Sheets up to 58 cm wide are suitable. Schlee sheet metal cleaning machine Type: Uni-58 Built in 2011 for sheets up to 58 cm wide cleans / brushes oiled mobile on wheels m. fixed Stainless steel More information on request. Dimensions: Height: approx. 115 cm Width: approx. 150 cm Depth: approx. 89 cm
KIMLA BPF 2070 CNC router was built in 2010 in Poland by POLCOM Przemysław Kimla. The machine is used for precision machining of parts made of such materials as wood, plastics and aluminium. The machining process is performed on a large work table with a length of 7050 mm and a width of 2085 mm by means of a reliable, high-speed spindle. Process stability, on the other hand, is ensured by an extremely rigid design that effectively eliminates any vibration and oscillation during even the most intense challenges. All this is complemented by an industrial CNC controller with easy-to-use PC-CAM software. The BPF 2070 CNC milling machine weighs 6000 kg. Technical specifications of the KIMLA BPF 2070 milling machine - machinable materials: wood, plywood, polycarbonate, polymer plates, aluminium, etc. - feed in the X/Y/Z axis: 2085/7050/500 mm - work area (L x W): 7050 x 2085 mm - maxim ...
maximum number of results exceeded
please refine your search
