usi clearing innocenti used for sale

The machines and lines of the SFM series are designed for processing nested containers such disposable syringes. The dosing station is designed to process liquid products using rotary piston pumps. Depending on machine type and equipment, nests are supplied manually or fully automatically. Filling and closing are always fully automatic. The machines are also designed for vacuum-assisted dosing and insertion of plunger stoppers. This virtually eliminates entrapped air when filling disposable syringes with pharmaceutical product

Manufacturer: Deltax Holder: Hydraulic holder Dimensions (L x W x H): 2010 x 902 x 1500 mm Knife length: 610 mm Number of strokes at 1/4 opening: 40 cuts at quarter opening Number of strokes at full opening: 12 cuts at full opening Measuring opening: 330 mm Cutting force: 206 tons Drive: 11 kw/32 CEE plug Weight: approx. 2250 kg Deltax_DTX600S with hydraulic holder (New machine) The DTX 600S has 20% more cutting power than the standard Deltax DTX600. This was achieved by installing a larger cylinder and using a smaller second pump. A larger first pump is used to maintain the same cutting speed. All other modifications are used to amplify the machine to handle the additional power. The weight gain due to the reinforcement modifications and the larger pestle is about 250 kg. Alternatively: Deltax DTX600 Difference Cutting force: 172 tons | Weight: 2000Kg | All othe ...

Snow slingshot Beilhack HS 231 Z, PTO drive 540 rpm.(in driving left, left), heavy design with mounting plate and hydraulic lifting, 360° hydraulically swivelling ejection fireplace, height-adjustable sliding skids. Clearance width 2.30 m, clearing height approx. 1.20 m, throwing distance up to approx. 12 m. Condition good, hydraulic hoses as good as new. other smaller snow blowers as well as snow clearing shields in stock - see photos.

The SteriWasher is an innovative new robust, high-performance, validateable part washing system designed for use in pharmaceuticals, biotechnology, food, beverages, healthcare and other critical areas. The washroom is accessible via a robust wing door and is made of 316 stainless steel. It is hygienically constructed. By using a combination of specially developed spraying technologies with variable performance, the washing machine offers energy-rich washing along with an energy-saving rinse, which is selected by a simple recipe selection. Description The SteriWasher ™ parts washers use existing and new technologies to provide an environmentally friendly washing system with low water and energy consumption in production and research environments for equipment ranging from critical small parts and tools to large mixers, barrels and containers. The range is available with a range of c ...

Punching machine EDEL - Maximum power: 25to. - Extension 26 cm - Height: 170cm - Width: 65cm - Depth: 50cm Good condition fully functional can be visited and tried out on site. Shipping abroad. Visit: Basically, I would like to point out to you that in order to avoid misunderstandings, the article can be viewed before purchase and tested under electricity. Please ask questions before purchasing to avoid any ambiguity. If you have any general questions or make an appointment for a visit, I can be reached at any time, using the telephone number below or above. Errors in the description and intermediate sale reserved. The VAT is shown separately on my invoices. Shipping with forwarding.

Scatterattachment Küpper-Weisser STA 95 – E50H, spreader for trucks with usable volume 5 m3, screw conveyor, hydraulic drive, spreading width 1 to 6 m, with tarpaulin folding roof, all-round warning light, GPS antenna, wind shield, control panel. More scattering and clearing technology available, see photos!

Feinbau Scherer PM 1 F-2 - 3 speed levels on the right - 3 speed levels on the left - Weight: 180kg - Height: 120cm - Depth: 50cm - Width: 100cm Good condition fully functional can be visited and tried out on site. Shipping abroad. Visit: Basically, I would like to point out to you that in order to avoid misunderstandings, the article can be viewed before purchase and tested under electricity. Please ask questions before purchasing to avoid any ambiguity. If you have any general questions or make an appointment for a visit, I can be reached at any time, using the telephone number below or above. Errors in the description and intermediate sale reserved. The VAT is shown separately on my invoices. Shipping with forwarding.

For sale we offer a measuring and weighing system for packages from Bedal. It is a perfect system for all package acceptance or shipping. It can be used for example.B: In shipping at industry, wholesale or e-commerce, fulfillment service providers (e..B. forwarding agents, logistics), or at parcel reception points (e.B. courier services). Package dimensions: Min. BxWxH 10x10x4 cm Max. BxWxH 43x41x48 cm undressed max: LxWxH 75x41x48 cm Tolerance: LxWxH 1.0 x0.5 x 0.5cm Weight: 0.25kg: 0.05Kg (50g) / 25-32kg : 0.075kg (75g) Parcel Kiosk is an economical solution for weighing and dimensioning packages. It is certified by the international organization OIML. Automating packet measurement improves efficiency and saves resources. Thanks to the Parcel Kiosk system, you can be sure that accurate weight and dimensions are read and that your company is protected from errors an ...

Polishing machine steel - Continuous speed - Height: 130cm - Depth: 110cm - Width: 100cm - Weight: 500kg Good condition fully functional can be visited and tried out on site. Shipping abroad. Visit: Basically, I would like to point out to you that in order to avoid misunderstandings, the article can be viewed before purchase and tested under electricity. Please ask questions before purchasing to avoid any ambiguity. If you have any general questions or make an appointment for a visit, I can be reached at any time, using the telephone number below or above. Errors in the description and intermediate sale reserved. The VAT is shown separately on my invoices. Shipping with forwarding.

Karl Hertel Bending Bench / Round Bending Machine Kombi - Width: 150cm - Depth: 90cm - Height: 120cm - Weight: 350kg Good condition fully functional can be visited and tried out on site. Shipping abroad. Visit: Basically, I would like to point out to you that in order to avoid misunderstandings, the article can be viewed before purchase and tested under electricity. Please ask questions before purchasing to avoid any ambiguity. If you have any general questions or make an appointment for a visit, I can be reached at any time, using the telephone number below or above. Errors in the description and intermediate sale reserved. The VAT is shown separately on my invoices. Shipping with forwarding.

KELLENBERGER UR 175-1000 Yes it is a machine that we are using in Exact. We replace it because a new Studer will arrive next week and we have no more space in the company. The machine works very well and has just been overhauled by us, replacing many electrical and mechanical parts. KELLENBERGER UR 175-1000 Hardinge

Wieland Suction Cup IS-30 T - Weight: 100 kg - rpm: 2895 - 3 kW - Space requirement: 600 x 1200 x 1200 mm Wieland Suction Cup IS-35 T - Weight: 90kg - RPM: 2895 Good condition fully functional can be visited and tried out on site. Shipping abroad. sightseeing: Basically, I would like to point out to you that in order to avoid misunderstandings, the article can be viewed before purchase and tested under electricity. Please ask questions before purchasing to avoid any ambiguity. If you have any general questions or make an appointment for a visit, I can be reached at any time, using the telephone number below or above. Errors in the description and intermediate sale reserved. The VAT is shown separately on my invoices. Shipping with forwarding.

Korsch EK III single station eccentric tablet press, maximum tablet diameter 60mm, maximum depth of fill 70mm (currently set for maximum 30mm depth of fill). Maximum pressure 200kN. Four speed (11, 22, 32, 42 strokes/minute) capacity up to 2520 tablets per hour, using a single-tip tool.

Ordering no: RE002 TECHNICAL DATA main saw diameter 300-550mm Height of the main saw adjustment vertically for a saw 0300 0-75mm for a saw ⌀350 15-100mm for a saw ⌀400 40-125mm for a saw ⌀450 73-150mm for a saw ⌀500 90-175mm for ⌀550 saw 120-200mm The height of the main saw adjustment at an angle of 45 ° for a saw ⌀300 0-50mm for a saw ⌀350 10-70mm for a saw ⌀400 28-85mm for a saw ⌀450 50-105mm for a saw ⌀500 63-122mm for ⌀550 saw 85-140mm Saw blade tilt 0-45° / (optional) 0-46 ° Length of sawing with an auxiliary table with the strip at the back of the table for a movable table 250 = 2500mm with a strip at the back of the table for a movable table 300 = 3000mm with the strip at the back of the table for a movable table 320 = 3200mm with the strip at the back of the table for a movable table 390 = 3700mm Sawing width using a bumper on an au ...

Romaco-Promatic P91S horizontal intermittent motion cartoning machine for strips, sachets, etc. carton size range min. 15 x 15 x 60 mm (AxBxC), max. 95 x 70 x 160 mm, capacity up to 140 cartons per minute, pre-folded leaflet inserter, ink deboss coder (2 lines each up to 12 digits), glue closure of the carton flaps using a Nordson ProBlue Type 7 hot glue unit, bar code reader for leaflet and carton, includes Romaco-Siebler FlexTrans FT1-400 with two (2) ABB FlexPicker robots for the automatic transfer of the strips, etc. from the belt into the infeed of the cartoner, product format range: pack width from 40 to 120 mm, pack length from 45 to 200 mm, stacking height up to 80 mm, capacity up to 375 packs per minute

The SUPERBOX is a box butterfly that feeds, opens, folds, shapes the boxes and seals their lower part with adhesive tape. Its great versatility also lies in the possibility of using commercially available adhesive tape rolls. The machine consists of a cardboard magazine, an area where the cartons are opened and an output roller conveyor, on which the bottoms of the folding cartons are provided with adhesive tape. The format change is conveniently controlled via 5 handwheels, which is followed by an adjustment of the passport stamps of the cardboard magazine and the position of the suction cups. specifications Product dimensions: Length: 570 mm Width: 410 mm Height: 500 mm Min. product dimensions: Length: 250 mm Width: 170 mm Height: 90 mm Cardboard magazine for standard machine: 50/60 Operating voltage: 400V 3Ph+T 50Hz (others on request) Power consumption: 1 kW  ...

Pester PEWO-fold 1 overwrapping machine for single cartons and carton collations, in OPP-, PVC-, PE-materials, with foil width from 90 mm to 300 mm, film thickness from 0.02 mm to 0.05 mm, maximum roll diameter 350 mm. Size range min. 60 x 60 x 20 mm, max. 400 x 350 x 140 mm, Machine controlled using ELAU/Schneider PacDrive, Electrical connection 3x400V, V+N+PE/50-60 Hz, connected load 5.2 kW/12.5A, Operating pressure 4 bar, compressed air 4 to 10 bar. Infeed height approx. 900 mm, outfeed height approx. 900-950 mm. Output up to 60 cycles/collations per minute. Includes: Infeed conveyor, 1100 mm long x 260 mm belt width, outfeed conveyor, 2000 mm long x 260 mm belt width, Alpha Compact labeller, PEWO-collect collating table, miscellaneous sets of format parts

turning diameter: 250 mm turning length: 100 mm control: SIEMENS 840 D total power requirement: 35 kW weight of the machine ca.: 7500 kg dimensions of the machine ca.: m E M A G (Germany) Vertical CNC Controlled Hard Turning and Grinding machine with tool turret and workpiece handling System Model VSC 250 DS Year 2004 # M7 28.69324 _______________________________________________________ Turning Ø, max. 250 mm Turning length internal / external 100 mm Workpiece length min./max. 29 – 100 mm 6-positon tool turret Ø / swing-Ø 480/790 mm Workpiece spindle Slide travel, X / Z / stroke 680 / 400 / 200 mm Feed rate / Quick feed X/Z 45/30 m/min. Feed force X/Z 5,5/11 kN Spindle speed 4.300 / 6.000 rpm Spindle drive 28 kW Total electrical load, ...

x-travel: 11200 mm y-travel: 3130 mm z-travel: 1000 mm Control: NUM 1060 W A-axis: +- 120 ° c-axis: +215/-210 ° spindle motor: 15 kW spindle taper: HSK-F63 turning speeds: 24000 U/min table width: 1500 mm table length: 9400 oder 2x3000 mm total power requirement: kW weight of the machine ca.: 20 t dimensions of the machine ca.: 14,6x5,0x4,225 m Use: e.g. for processing aluminum panels, drilling profiles, advertising (signs milling, etc.), mold construction (prototypes) and processing of light steel frames / -beams using HSC milling The vertically arranged high-frequency milling spindle for automatic Tool change is mounted in a fork head on the Z-axis plate. The Spindle can be moved with the fork head in 2 NC axes, in the A axis and the C-axis. The vertical movement is carried out via the Z-axis. Liquid cooling via a cooling unit. Tool magazine: moving plate changer in the potal, outsid ...

Qty. 1 Second-hand section rolling mill plant Mfc.: Pomini, OMV, BM, Bendotti Built: 1989 continuously modernised Stopped: 2019 Installed power: 16.2 MW Billet income sizes: 120 x 120 up to 160 x 160 mm Length: 6.0 m Section production: Round bar dia.: 30 – 60 mm Angles from 30x3 up to 100x12 mm U” channel from 40x20 and 120x55 mm T” shape from 30 till 100 mm T” shape from 30 to 120 mm (Special for elevator rails- Leader in Europa) The rolling mill can be implemented with many other profiles by using different grooved rolls. Production capacity: 250,000 – 270,000 T/annum depending on the production mix Scope of supply: Reheating furnace Section rolling mill line Tying Machine Descaler Bundle Machine Cooling tower Machine shop

: Bj. 1996 pulling capacity: 100 kn stroke length max.: 2500 mm speed: 1-22 m/min return speed: 2-27 m/min Control: SPS S5-115 U Cast aluminum bars were cleared mechanically on this production line machined (drilling / milling) and separated into individual parts This also includes: -1 broaching machine (HOFFMANN, horizontal) so far for steel processing (Shift rods) - Horizontal broaching machine from Hoffmann - Machine type: RAW 630 x 2500 x100 - year of construction 1984 - Control S5 Siemens - 4 clearing points with 3 partial positions each - 1 x reloading for rear side processing - Loading and unloading: - 3x bunkers for raw parts - 3 x feed belts - Loading and unloading handling with 4 x loading and 4 x unloading grippers - 1 x turning device - 3 x material buffers for finished parts - year of construction 1995 - Siemens S7 control The data for this ad was created with ModulMWS - t ...

sheet width: 3100 mm plate thickness: 50 mm pre-bending: 40 mm total power requirement: kW weight of the machine ca.: 40 t dimensions of the machine ca.: 6,7 x 3,0 x 3,0 m 4-ROLL Hydraulic Plate Rolling Machine Working length 3100 mm Maximum thickness Pre-bending 40 mm Bending 50 mm Yield Point: 240 N/mm2 Number of rolls 4 Motor Power 55 kW Min. diameter mm - Ø Top Roll Diameter x 3 Top roll Ø 540 mm Bottom roll Ø 510 mm Side roll Ø 440 mm Length 6700 mm Height 3000 mm Width 3000 mm Weight 40.000 kg With: Cone bending device Induction hardened rolls Digital readout for side rolls Fully welded steel (St-52) frame Separate moveable control panel Dual bending speeds Electronic Parallelism All rolls are mounted in spherical roller bearings Hydraulically opened/closed drop end controlled from control panel Activation of cone rolling function and position adjustment via buttons on the  ...

The Diper Design DEVANADORA D5-EH-V35 sheet profiling machine was built in 2004 by the Spanish company Diper Design. The machine is designed for profiling metal sheets with a maximum width of 1250 mm. The mandrel diameters (closed / open) are 450 and 550 mm, respectively, and the roller diameter is 1500 mm. The profiling machine works with a bending speed of 35 m / min. Roof flashings were produced on the machine. By using an appropriate matrix on the machine, it is possible to produce e.g. gutters, metal shelves, window sills, profiles, etc. The total weight of the machine is 5 tons. The machine is fully operational and ready for further work. Technical data of the Diper Design DEVANADORA D5-EH-V35 profiling machine - bending speed: 35 m / min - maximum sheet width: 1250 mm - roll diameter: 1500 mm - spindle diameter (closed): 450 mm - spindle diameter (open): 550 mm – maximu ...

core drilling diameter max.: 25 mm bore depth: 1000 mm swing diameter: mm total power requirement: 25 kW weight of the machine ca.: 12,5 t dimensions of the machine ca.: m T B T (Germany) CNC-Controlled Horizontal Deep Hole Drilling Centre Model BWP 250 Year 1996, but reconditioned mechanically and electrically in 2006 ______________________________________________________________________ _____________ Working range: X Axis, machine column cross 2,000 mm Z Axis, drilling slide horizontal 1,200 mm Drilling depth 1.000 mm Y Axis, drilling slide vertical 1,100 mm Table clamping area 1,200 x 2,000 mm Drilling capacity in solid material, approx. 4 - 25 mm Tool holder taper HSK 50 Spindle speeds 1.260 - 15,000 rpm Feed rates / quickfeed, XYZ, infinitely variable 100 - 10,000/15.000 mm/min. Force rate of feed  ...

pressure: 10 t throat: 0 mm stroke: 400 mm total power requirement: 7,5 kW weight of the machine ca.: 6500 t dimensions of the machine ca.: m D U N K E S (Germany) CNC Controlled Hydraulic Double Column Press Model HD 10 Year 1993 ________________________________________________________ Pressure 10 tons Ram stroke 400 mm Mounting height 600 mm Table size 400 x 300 mm Table height above floor 820 mm Ram area 400 x 300 mm Ram bore 40 mm Quickspeed, downwards, max. 70 mm/s Working speed, downwards, using max. pressure 40 mm/s Working speed, min. 5 mm/s Working speed adjustable from 5 - 70 mm/s Return stroke speed, min./max. 20 / 175 mm/s Drive 7.5 kW Total electrical load, approx. 12 kW - 380 V - 50 Hz Weigh ...

Fill 3D-Ultrasonic Cutter Here we offer you a Fill 3D ultrasonic cutting system. Fill 3D-ULTRASONIC SCHNEIDER 3D ULTRASONIC CUTTER The 3D ultrasonic cutter from Fill enables three-dimensional contour cutting of fiber-reinforced plastics using ultrasonically excited cutting systems. Your advantages: Ergonomic feeding and unloading Easy creation of bleed programs (NC control) Space-saving system concept (as an alternative to the robot) High repeatability High process stability Easy and fast tool change Possible integration into an overall process chain The principle: The linear axis portal enables precise guidance of the ultrasonic knife with a small footprint and simple kinematics. Thanks to the Siemens 840 D CNC control, the trimming device can be programmed like a machine tool. Tool corrections or path changes can simply be carried out directly on the machine. As standa ...

Grinding diameter: 0 mm Grinding length: 0 mm Workpiece weight: 0 kg CNC Brand: 0 CNC Model: 0 Control: GE FANUC Series 18-T Technical data Centre height: 175 mm Distance between centres: 1000 mm Max. grinding diameter: 348 mm Grinding length: 1000 mm Workpiece weight on centres max.: 250 kg Grinding wheel: Diameter: 500 mm Width: 100 mm Peripheral speed: 45 m/s Longitudinal slide: Max. travel: 1400 mm Resolution: 0.0001 mm Feed speed up: 8000 mm/min Transversal slide: Max. travel: 340 mm Resolution: 0.0001 mm Feed speed up: 8000 mm/min Swivelling range: +9/-9 ° Work piece spindle head: speeds: from: 20 rpm up to: 1000 rpm rotatable: +30/-45 ° Précision d´usinage: 0.0005 mm taper in spindle: MT: 6 Tailstock: Taper in tailstock:: 4 MT Tailstock travel of barrel: 50 mm Voltage 50 Hz 3x: 400 Volt Grinding spindle motor: 15 kW Total power required: 26.5 kW Total power requi ...

workpiece diameter: 250 mm centre distance: 0 mm honing length max.: mm max. module: 5 Gear Ø, min./max. 10 / 250 mm Module range 1 - 5 Length of teeth / max. table stroke 500 mm Height of centres of tailstocks 220 mm Max. weight of workpiece 50 / 100 kg Honing head swivelling +/- 35 ° Speeds of honing tool 20 - 500 rpm Size of honing tool, Ø x width 300 x 40 mm Workpiece speeds 500 - 3,000 rpm Total adjustment of cross slide 270 mm Rapid traverse of cross slide 50 mm Infeed travel of cross slide, mechanical 1 - 8 mm/Ø Roughing / finishing infeed 1 - 29 / 0.2 - 2.8 mm/sec Table speeds, hydraulic 0 - 6 m/min Total electrical load 5.5 kW - 380 V - 50 Hz Weight 3,200 kg Accessories / Special Features Working parameters can be preset using counters and control units. Automatic working process with workpiece counter. All roughing and finishing infeeds can be adjusted by a decade switch ...

rolling capacity max.: NA t workpiece diameter: 38 mm workpiece length: 500 mm total power requirement: 24 kW weight of the machine ca.: 10 t dimensions of the machine ca.: m Max.Ø tool slide stroke 760 mm Max.Ø rack length 610 mm Length of workpiece between centres, approx. 500 mm Max. tooth width / profile width 92 mm Max. workpiece Ø 38 mm Tailstock stroke on outboard support, hydraulic, approx. 500 mm Module range 0.3 - 1.3 Total electrical load, approx. 24 kW - 380 V - 50 Hz Weight, approx. 10,000 kg Accessories / Special Features KBH Workpiece Feed Device, standing parallel to the machine, at present set-up for feed-in and feed-out of shaft-formed workpieces, approx. Ø 16 x 200 mm long, with prism conveyor belt and lifting station for 2 shafts (blank and finished part), as well as workpiece positioning control. Originally, external gears were formed on the machine using  ...

Qty. 1 Second-hand section rolling mill plant Mfc.: Pomini, OMV, BM, Bendotti Built: 1989 continuously modernised Stopped: 2019 Installed power: 16.2 MW Billet income sizes: 120 x 120 up to 160 x 160 mm Length: 6.0 m Section production: Round bar dia.: 30 – 60 mm Angles from 30x3 up to 100x12 mm U” channel from 40x20 and 120x55 mm T” shape from 30 till 100 mm T” shape from 30 to 120 mm (Special for elevator rails- Leader in Europa) The rolling mill can be implemented with many other profiles by using different grooved rolls. Production capacity: 250,000 – 270,000 T/annum depending on the production mix Scope of supply: Reheating furnace Section rolling mill line Tying Machine Descaler Bundle Machine Cooling tower Machine shop

Drilling capacity in St 60: 40 mm threading in St 60: M 24 threading in GG 20: M 30 Short spindle: MK 3 bore stroke: 120 mm throat: 293 mm column diameter: 115 mm Machine table - usable table surface: 514x360 mm T-Slots Amount - Width - Distance: 2 x 14 x 224 mm Distance spindle - machine table min./max.: 117/701 mm feed: 0,10 + 0,20 mm/U spindle turning speed range: 160-2.250 UpM total power requirement: 1,45/1,9 kW height of the machine: 1840 mm weight of the machine ca.: 285 kg Standard equipment: 7 TFT - LCD display with touch function: manual input of spindle speed Setpoint, speed display actual value, integrated drilling depth display with touch Zero point transfer, virtual drilling depth scale in the display, machine Status displays and warnings in the display, service information, selectable User language: DE / EN / FR / ES / IT / NL / RU Pos. 37.5 Technology computer in the disp ...

: 26 mm : 30 mm : 30 mm threading in St 60: M 20 threading in GG 20: M 24 : MK 3 : 120-2.200 U/min. throat: 293 mm : 514x360 mm : 2 x 14 x 224 mm : 90/675 mm column diameter: 115 mm spindle stroke: 160 mm feeds: 0,1-0,2-0,3-0,4 mm/U total power requirement: 1,0/1,6 kW Machine height: 1865 mm weight: 380 kg Standard equipment: 7 TFT LCD display with touch function: manual input of spindle speed Setpoint, actual speed display, integrated drilling depth display with touch Zero point transfer, virtual drilling depth scale in the display, machine Status displays and warnings in the display, service information, selectable User language: DE / EN / FR / ES / IT / NL / RU - Thread cutting device, for thread cutting with stop, max. 6th Thread / min (thread cutting performance dependent on spindle speed), thread depth adjustable via depth stop and in the TFT - LCD display (4 tools) - Infinitely va ...

: 34 mm : 40 mm : 40 mm threading in St 60: M 24 threading in GG 20: M 30 : MK 4 : 100-1.800 U/min. throat: 300 mm : 615x430 mm : 2 x 14 x 224 mm : 138/688 mm column diameter: 145 mm spindle stroke: 160 mm feeds: 0,1-0,2-0,3-0,4 mm/U total power requirement: 1,4/2,2 kW Machine height: 1865 mm weight: 470 kg Standard equipment: 7 TFT LCD display with touch function: manual input of spindle speed Setpoint, actual speed display, integrated drilling depth display with touch Zero point transfer, virtual drilling depth scale in the display, machine Status displays and warnings in the display, service information, selectable User language: DE / EN / FR / ES / IT / NL / RU - Thread cutting device, for thread cutting with stop, max. 6th Thread / min (thread cutting performance dependent on spindle speed), thread depth adjustable via depth stop and in the TFT - LCD display (4 tools) - Infinitely v ...

groove width: 16 mm x-travel: 16-200 mm table length: 1500 mm table width: 375 mm milling spindle: ISO 40 max. clampable toolpiece shaft diameter: 30 mm max. useable hobs, normal diameter: 40 mm distance between milling spindle and table: 150-250 mm axial move. of milling spindle (auto./manual): 120 mm vertical adjust. of milling slide (manual): 100 mm weight of the machine ca.: 3,1 t dimensions of the machine ca.: 2,00x1,40x2,40 m K4 - TECHDETAIL UK: 0,11 kW K4 - TECHDETAIL UK: 0,6/1,1 kW K4 - TECHDETAIL UK: 3 x 0,012-0,05 mm/U K4 - TECHDETAIL UK: 16x60 mm K4 - TECHDETAIL UK: 12 x 280 - 3550 U/min K4 - TECHDETAIL UK: 0,85 kW K4 - TECHDETAIL UK: 0-2,0 mm K4 - TECHDETAIL UK: 250 mm Condition: ready for production The machine is suitable for the manufacture of flutes and slots using undersize cutters with hydraulic adjustment. Roughing and finishing can be done in one single clamping.  ...

max. wheel diameter: 1600 mm gear width: 250 mm max. module: 20 min. module: 1,5 base circle dia. - max.: 1450 mm base circle dia. - min.: 150 mm specimen weight from/to: 4000 kg feeler adjustment movement - parallel: 1400 mm max.helical angle: 0 - 90 ° wheel diameter with counterstay: 1000 mm feeler adjustment movement - parallel: 800 mm centre height: 1150 mm electrics - voltage/frequency: 400 / 50 V/Hz dimensions of the machine ca.: 2,8 x 2,4 x 2,3 m total power requirement: 2 kW weight of the machine ca.: 3 t Universal Involute and Helix Testing Machine - modernized 1995 Machine is suitable for measuring all individual tooth data on straight and helical spur gears, and shaping and shaving cutters. Following tooth data can be tested: Tooth flanks, Involute base circle dia. and pressure angle, Profile c ...

FMS SYSTEM: Machining Cell consisting of: Two 5-Axis machining Centres 8-Pool Pallet System(1250 x 1250mm x 3.000kg) Pallet Storage System X= 3.000 mm, Y= 2.000H/1.720V, Z= 2.000mm; A= 175°, B=0,001°; 640 Pos. ATC ; Spindle Taper HSK-A100; Spindle n= 3.000; Motor 50kW; Feeds: X,Y= 40m/min, Z= 30m/min Siemens 840D, Chip-conveyor; Serial No. 1450-03 and 1451-3, both from 2003 FR: À VENDRE MAINTENANTFMS SYSTEME ; 8 Pos. Piscine à palettes (1250 x 1250mm x3.000kg). 2x MCM Jet Five Mirror 5 axes CENTRE D'USINAGE/BEARBEITUNGSZENTREN/MACHINE CENTERS, X= 3.000, Y= 2.000H/1.720V, Z= 2.000mm ; A= 175°, B=0,001° ; 640 Pos. ATC ; Cône de broche HSK-A100 ; Broche n= 3.000 ; Moteur 50kW ; Alimentation : X,Y= 40m/min, Z= 30m/minSiemens 840D, convoyeur à copeaux ; numéros de série 1450-03 et 1451-3, à partir de 2003

max. wheel diameter: 215 mm gear width: 40,65 mm max. module: total power requirement: 20 kW weight of the machine ca.: 10 t Max. external Ø of workpiece 215 mm Tooth profile, height x width 16 x 40.65 mm No. of teeth 5 - 200 Max. tooth ratio 1 : 10 Grinding wheel Ø 51 - 190 mm Grinding wheel speeds 1,000 - 6,000 rpm X Axis (horizontal) 152 mm Y Axis (vertical) 178 mm Z Axis (slide base plate) 304 mm Distance from middle of machine to middle of workspindle 115 mm Axial speed 125 mm/sec Workpiece speeds 0 - 30 rpm Workspindle bore, conical 3 29/32 inch Total electrical load 20 kW - 380 V - 50 Hz Weight, approx. 10,000 kg Accessories / Special Features FANUC CNC Control, Model 150 MB, for 7 axes, with monitor and direct input. Automatic calculation of all workpiece and grinding parameters. Extensive coolant equipment with filter system, band filter, etc. Driv ...

max. wheel diameter: 400 mm max. number of teeth: 150 max. module: 5 total power requirement: 16 kW weight of the machine ca.: 10 t Workpiece Ø, min./max. 30 - 400 mm Number of teeth 6 - 150 Module range, max. 5 Tool holder shaft Ø SK 30 / 20 Tool speeds 4,000 rpm Spindle drive max. infinitely variable 1.8 kW Feeds, longitudinal and cross 0.001 - 12 m/min Workpiece speed, max. (1.5 kW) C Axis 2,000 rpm Workspindle slide 400 mm Tool speed, max. 3,000 rpm Tool holder SK 30 Total electrical load, approx. 16 kW - 380 V - 50 Hz Weight, approx. 10,000 kg Accessories / Special Features BWO (HECKLER & KOCH) CNC Control model 785 H for altogether 7 axes. Input via monitor. The control has all the supervision and fault diagnosis features necessary for fully automatic working process. 2 workspindle units, left and right, which can be set at any angle. CNC controlled: Z and W Axes for tool cr ...

FMS SYSTEM; Machining Cell consisting of: Two 5-Axis Machining Centres 12-Pool Pallet System (630 mm X 630 mm); Pallet Storage System X= 750 mm, Y= 860 mm, Z= 850mm; B= 0,001°; 334 Pos. ATC Spindle Taper HSK-A100; Spindle n= 11.000; Spindle 25 kW; Feeds 32.000mm/min; Chip-conveyor; Coolant System Serial No. 1283-01 (2001) Siemens 840D; and Coolant System Serial No. 1024-98 (1999) Siemens 840C FR: À VENDRE MAINTENANTFMS SYSTEME ; 12 Pos. Piscine à palettes (630 X 630mm) ; 2x horloge MCM 5 axes CENTRE D'USINAGE/BEARBEITUNGSZENTREN/MACHINE CENTERS ; X= 750, Y= 860, Z= 850.mm ; A= .. ? ? B= 0,001° ; 334 Pos. ATC ; cône de broche HSK-A100 ; broche n= 11.000 ; broche 25 kW ; avance 32.000mm/min ; convoyeur à copeaux ; système de refroidissement n° 1283-01 (2001)Siemens 840D ; et système de refroidissement n° 1024-98 (1999)Siemens 840C

pressure: 100 t chamfer lenght: 3100 mm distance between columns: 2550 mm column arm: 450 mm ajustment speed: 160 mm/sec working feed: 10 mm/sec return speed: 120 mm/sec work stroke: 270 mm back stop - adjustable: 650 mm table height: 850 mm table width: 100 mm tank capacity: 200 l total power requirement: 7,5 kW weight: 7,5 t Overall size: 3,76 x 2,15 x 2,76 m GENERAL SPECIFICATIONS Hydraulic operation with two cylinders – Assistmach High performance hydraulic gear pump – Rexroth High pressure filter (with clogging detector and bypass) placed before all components, Air removal filter in the reservoir Fast descent by gravity, bending phase and return of the ram are controlled electronically via a proportional flow valves h Bending force controlled by proportional pressure valves – Rexroth Quality oil with high viscosity index Frame is designed and sized using Analyze program Hydrau ...

Clamp length: , mm Clamp width: , mm : , Nm RU-LH Painting Assistance Painting assistance for the simultaneous painting of sash and glazing ledges. A clamp has to be positioned in each corner of the already made frame. The operation is started by using a foot valve. For different thickness of ledges the clamping device is height- and depth adjustable. The positioning is diagonally and the clamps stick out of the wood about 25 mm. Now the frame can be pressed into the sash and is fixed. For the painting the frame is positioned now about 10 mm outside in front of the sash. After drying, the frame is pressed into the sash, it will be removed before the glazing. The clamps can be removed by hand for the further processing. For different thickness of ledges the clamping-device is height- and depth adjustable. The height is adjustable from 700 – 1200 mm. Advantages: Quick assembly No jammin ...

working length: mm Working width: mm Working height: mm TGT Robby 420 universal, the glass mounting device for working without Effort The TGT Robby 420 420 universal is battery powered and its Telescoping movements, crane arm forward (work 1,25 m in front of the wheels), adjust large discs sideways exactly (100 mm to the right 100 mm to the left), and the lift head to Tilt 60 ° and turn 180 ° upwards, are using a Cable remote control made. Equipped with an Accusauganlage carrying capacity approximately 500 kg the TGT Robby 420 universal is the safe response aid. Of course, the lift head can also be rotated 360 ° manually. moreover The lift head can be equipped with an articulated joint (Turn the disc completely sideways) to drive through narrow doors to be able to. The TGT Robby 420 universal is also with a strong front-wheel drive equipped, so the effor ...

GeneralVertical Machining Centres; Control: Control F0iMF CharacteristicsTable surface1400 x 560 mmMovement X / Y / Z1100/560/510 mmSpindle taperBT 40 Tool Magazine with60 PositionsDrive power (25% DC)15 kWDrive power (100% DC)11 kWSpeed max.12000 rpmMaximum load (table centre)1000 KgRapid feed X / Y / Z36/36/30 m/minDimensions (L x W x H)3,19 x 2,76 x 2,94 (3,82 x 3,58 x 3,01) mWeight approx.5500 KgStandard spindle 12,000 min-1, 15/ 11 kWStandard Spindle 12,000 min-1, 15/ 11 kW Spindle speed: 12,000 min-1 Output: 15/13/11 kW (20/17.33/15 HP) (25%ED/30min/cont) Torque: 119/70/57 Nm (87.76/51.62/42.04 ft·lbf) (25%ED/30min/cont)Spindle Taper 7/24 Taper #40/ Grip MAS Spindle Taper 7/24 Taper #40/ Grip MAS This specification uses the spindle No. 40 7/24 taper / Grip MAS tool holder. The grip type and retention knob type of ATC are specified separately.Retention Knob: Special (Center-Throug ...

cutting diameter: 330 mm saw band length: 3870 x 34 x 1,1 mm cutting width: 400 mm band speed: 15 - 90 m/min : 400 x 200 mm cutting capacity - round: 330 bei 90° mm : 250 x 170 mm cutting capacity - round: 250 bei 45° mm work height max.: 940 mm cutting capacity - square: 320 bei 90° mm cutting capacity - square: 230 mm total power requirement: 3,0 kW weight of the machine ca.: 665 kg dimensions of the machine ca.: 2660 x 204 x 2060 mm Description: The ARG 330 F. is a robust manual metal band saw with high cutting accuracy for medium to heavy workpieces! Your exceptionally compact design, as well as its massive saw frame made of gray cast iron are ideally suited for use in workshops and production facilities. The The basic equipment of the machine enables the processing of a wide variety of different materials, including stainless and tool steels. With With this machine, miter cuts ar ...

bore capacity in steel (diameter): 50,0 mm arm length: 320 - 1.220 mm workpiece height max.: 330 - 1.170 mm turning speeds: 25 - 2000 U/min spindle taper MT: 5 MK base plate: 1300 x 980 mm threading: 42 M quill stroke: 335 mm total power requirement: 4,0 kW weight of the machine ca.: 3000 kg. range L-W-H: 2035 x 1000 x 2830 mm Furnishing: - Large-sized base plate, ideal for processing large workpieces - Thick-walled, polished column for increased sliding properties of the boom - Extension arm and drill head with independent hydraulic clamping - Simple height adjustment of the extension arm using a lifting motor - Ideal for drilling, countersinking, reaming and thread cutting - Hardened and ground gears, running in an oil bath - Good gliding ability of the drill head on the boom - sanded surface Scope of delivery: - Cube table - Drill chuck arbor MK 5 / B 16 - Reducing sleeves MK 5/4, MK  ...

Double standing seam roofing machine F3 is used for making double standing seam lock for the roofing panels that are used for installation of the double standing seam roofing. The double standing seam roofing is widely used because it’s impossible for the water to get under the closed double standing roofing panels in the places of their contact with each other, thanks to lock’s special shape. The special shape means that double standing seam panels cover each other in the places of their contact, and after their installation on the roof it will be closed using special double standing seam closing tools (manual tool for closing double standing seam lock and electric machine for closing double standing seam lock). The advantage of this Standing seam machine is possibility to change the width of the standing seam roofing panels in very simple way. There’s a special screw at th ...

Window drip cap roll forming machine PO-1 Window drip cap roll forming machine PO-1 allows to produce window trim” profile by rolling the sheet metal through forming rolls. A window trim is an element that is widely used in construction while windows installation. In the standard way the window trim is bent step by step using a manual folding machine. This is a cheaper, but more time-consuming process. The metal sheet must be pre-marked for each bending operation. Each bend is then performed using a manual bending machine. The operator must set the necessary dimensions according to the marks, fix the sheet metal with the machine's fixation mechanism, and then bend it. The length of the window trim is limited to the maximum working length of the bending machine. Thus, each manual folding operation is time-consuming and the production process becomes expensive and inefficient. To im ...

Grooving machine, make RAUSCH type RS 1/800Masch. -No: 1384 built in 1964Technical specifications:Clearing force 1.0 tStroke 800 mmMax. Groove width 20 mmMax. Tool length 1000 mmClearing speed 3.0 m / min.Rewind speed 6.0 m / minTable size 320 x 220 mmDrive power 1.5 / 3.0 kWWeight 340 kgExternal dimensions approx. 700 x 600 x 1500 mmWith- 8 broaches: 5JS9, 6JS9, 8JS9, 8P9, 10J9, 10R9, 12J9, 14J9- many guide bushesused, despite the year of construction in good conditionPrice on request.Delivery: ex warehouse or location free loading truck.Payment: net at takeover or by appointment.Technical data are not binding. Errors excepted.We would be pleased, if you like our offer and are always available for your queries.Best regardsM. WaldeckWAHO Machine Tools

sheet width: 1020 mm plate thickness: 2,0 mm daylight opening: 48 mm bending angle max.: 0 - 135 ° work height max.: 900 mm total power requirement: von Hand kW weight of the machine ca.: 285 kg dimensions of the machine ca.: 1350 x 820 x 1140 mm Furnishing: - Segmented upper and bending beam for a wide variety of bending options - Clamping by means of a foot pedal - Hands remain free for optimal positioning of the sheet - Universally applicable bending machine for plumbing and repair shops - Robust construction in a modern design - Manual bending machine for standard bending tasks - Segmented upper beam for a large number of bending options - Optimal price-performance ratio - Quick and easy bending process using a bow handle - Non-slip rubber coating on the foot pedal for safe working - Easy adjustment of the lower beam to the respective sheet thickness - High upper beam for producing  ...

ully automatic wood copy milling machine make REICHENBACHER type KS225Make -No: 1182, year of construction 10/1994 with Siemens OP 393 III controlSimultaneously mills and grinds two small parts with complicated shapes, such as tobacco pipes, golf club heads, sports pistol grips, wooden shift levers, etc.Technical specifications:machine constructionStable frame construction in a closed, against dust andNoise-encapsulated housing. Upper area of the front with gas pressure springHinged door, with security window.machine equipmentTo craft 2 copies of a model at once, you have:2 milling spindles each with a milling head dia. 240 mm (equipped with HS steels), via flat belts jointly driven by motor 2.2 kW; number of milling spindles 7200 rpm; Direction of rotation right.2 grinding units each with a 120 mm wide endless grinding belt, together with a 0.75 kW motor driven; belt speed 13 m/s; wi ...