| Standard spindle 12,000 min-1,
15/ 11 kW |
Standard Spindle 12,000 min-1, 15/ 11 kW
Spindle speed: 12,000 min-1 Output: 15/13/11 kW (20/17.33/15 HP)
(25%ED/30min/cont) Torque: 119/70/57 Nm (87.76/51.62/42.04 ft·lbf)
(25%ED/30min/cont) |
| Spindle Taper 7/24 Taper #40/ Grip MAS
|
Spindle Taper 7/24 Taper #40/ Grip MAS
This specification uses the spindle No. 40 7/24 taper / Grip MAS tool
holder. The grip type and retention knob type of ATC are specified
separately. |
| Retention Knob: Special (Center-Through)
(7/24 Taper #40) |
Retention Knob: Special (Center-through) (7/24
Taper #40) The spindle collet applicable to the special
(center-through) retention knob is installed. Tool retention knob is
not included. The through-spindle coolant specification requires a
dedicated r |
| Interface for Workpiece seating detection
(1 line) |
Interface for Workpiece Holding Detection (1
Circuit) For the workpiece holding detection interface, pneumatic 1
circuit 1 port are provided on the in-machine ceiling (right side).
The panel is installed on the upper right of the machine front and
the p |
| Interface for Hydraulic fixture
(hydraulic 2 circuits ) |
Interface for Hydraulic Fixture (Hydraulic 2
Circuits) For the fixture interface, hydraulic 2 circuit 4 ports are
provided on the in- machine ceiling (right side). The hydraulic unit
(made by NACHI) put on the oil pan with casters is placed at the
rear |
| Tool storage capacity 60 tools |
Tool Storage Capacity 60 Tools Chain-type magazine
Tool capacity: 60 tools Technical random address type Max. tool
diameter - With adjacent tools: f80 mm (dia.3.15 inch.) - Without
adjacent tools: f125 mm (dia. 4.92 inch.) Max. tool length: 300 mm
(11. |
| Chip conveyor (left discharge, inner pan
scraper type + drum filter) |
Chip Conveyor (Left Discharge, Inner Pan Scraper
Type + Drum Filter) Install the chip conveyor on the front side of the
machine. The discharge direction is left side. Chips accumulated on
the inner pan in the conveyor are scraped up by the scraper and
d |
| (X)Through-spindle coolant system (unit
on coolant tank) (center through, 1.5 MPa) |
Through-spindle coolant system (unit on coolant
tank) (center through, 1.5 MPa) |
| Coolant gun for machining side |
Coolant gun for machining side A coolant gun is
equipped on the front side of the machine for cleaning chips
accumulated inside the machine or adhering to the workpiece or the
fixtures. |
| Additional coolant system for tool
tip |
Additional Coolant System for Tool Tip Two
coolant nozzles are added to the rear side of the spindle. The
orientation of the additional nozzles can be adjusted. |
| Additional air blow for tool tip |
Additional Air Blow for Tool Tip One air blow
nozzle is added to the right side of the spindle. The orientation of
the additional nozzle can be adjusted. |
| (X)Mist collector (AFS 600) |
Mist collector (AFS 600) Mist and tiny dust
generated by machining are vacuumed and filtered. The filtered mist
is returned back to coolant tank. The mist collector is installed
onto E-box. Oil-based coolant is not available. |
| In-machine measuring system (spindle,
table) (RENISHAW) + W Setter (tool setter + workpiece setter) (tool
length + diameter) |
In-machine Measuring System (Spindle + Table)
(RENISHAW) + W Setter (Tool Setter + Workpiece Setter) (tool length +
diameter) This specification is a set of Renishaw touch sensor spindle
(OMP40) and table (OTS). Mounting the touch sensor on the spindle |
| Signal lamp Buzzer (SK-OP) |
Signal Lamp Buzzer The operator is informed of
the machining status with the buzzer according to the signal lamp
indication. The signal lamp is not included. It is necessary to
select the signal lamp separately. The buzzer continues to sound when
an A |
| Right Side Shutter |
Right Side Shutter The shutter that moves along
with vertical direction is attached. It is driven by pneumatic
cylinder. - Shutter opening/closing time: 3.5 sec. - Shutter opening
width: W 610 mm × H 774.5 mm (W 24.02 inch. × H 30.49 inch.) -
Distance f |
| EtherNetI/P I/F |
EtherNetI/P I/F This I/F is used for transferring
control signals between the machine and peripheral equipment via
Ethernet. This I/F can be connected to all peripheral equipment that
has terminals corresponding to LAN cables. This specification
D4452871 also |
| Interface for Robot (EtherNet/IP), Need
to select EtherNet/IP Interface |
Robot I/F (EtherNet/IP), Separate EtherNet/IP I/F
Required The interface signals for mounting robots are made
available. The signals are exchanged with the robots using the
EtherNet/IP communication protocol. The use of the robots allows the
automatic |
| Safety fence Interface (electric
Interface) |
Safety fence Interface (electric Interface) It
provids interface for the protective fence. It confirms the machinery
status (machine door, side shutter etc.) and determines the behavior
enable / disable according to the input of the interface for the
fe |
| [Robot system] Handling Package (work
stocker) 20kg |
Handling Package (work stocker) 20kg It consists
of a robot (M-710iC/70), robot hand, workstocker, temporary workpiece
station, NG chute, fence, and MAPPS-R. The robot system
attaches/detaches workpieces and discharges NG workpieces to the NG
chute. Ha |
|
|
| Manual pulse generator (separate
type) |
Manual pulse generator (separate type) Adding
handy type pulse handle improves operability during set-up operation.
The switch on the operation panel can change which pulse handle is
used on the operation panel or handheld side. Handheld pulse handle
o |
| Setting Unit mm |
Setting Unit, MM The unit to be used for the
screen display and program commands is set to millimeter (mm).
Turning: MM specification for the turret Horizontal machining center:
MM specification for the tapped pallet |
| Part program storage length 2 MB (5,120
m) in total + Registerable programs 1,000 in total (SK-OP) |
Part Program Storage Length 2 MB (5,120 m) in
Total + Registerable Programs 1,000 in Total The storage capacity of
CNC can be increased to 2 MB (5,120 m) to register up to 1,000
programs. |
|
|
| Screen display German |
Screen display German Language on MAPPS Screen:
German Language on MAPPS Warning Screen: German Language on NC Screen:
German Language on PC Screen: German |
| Please notice, for this machine you must
have a transformer. |
Please notice, for this machine you must have a
transformer, the transformer is not part of the machine equipment and
must be ordered separately. |
| Special equipment |
- DDRT-200X (connected through table) -
Rotary joint (6+1 Ports) for DDRT-200X - In-machine pipe parts -
Fixture for Measuring package - Measuring Module (CMM Inline 3D
measurement) - Add proximity sensor for workpiece stocker (between
loader |